-
First results on monolithic CMOS detector with internal gain
Authors:
U. Follo,
G. Gioachin,
C. Ferrero,
M. Mandurrino,
M. Bregant,
S. Bufalino,
F. Carnesecchi,
D. Cavazza,
M. Colocci,
T. Corradino,
M. Da Rocha Rolo,
G. Di Nicolantonio,
S. Durando,
G. Margutti,
M. Mignone,
R. Nania,
L. Pancheri,
A. Rivetti,
B. Sabiu,
G. G. A. de Souza,
S. Strazzi,
R. Wheadon
Abstract:
In this paper we report on a set of characterisations carried out on the first monolithic LGAD prototype integrated in a customised 110 nm CMOS process having a depleted active volume thickness of 48 $μ$m. This prototype is formed by a pixel array where each pixel has a total size of 100 $μ$m $\times$ 250 $μ$m and includes a high-speed front-end amplifier. After describing the sensor and the elect…
▽ More
In this paper we report on a set of characterisations carried out on the first monolithic LGAD prototype integrated in a customised 110 nm CMOS process having a depleted active volume thickness of 48 $μ$m. This prototype is formed by a pixel array where each pixel has a total size of 100 $μ$m $\times$ 250 $μ$m and includes a high-speed front-end amplifier. After describing the sensor and the electronics architecture, both laboratory and in-beam measurements are reported and described. Optical characterisations performed with an IR pulsed laser setup have shown a sensor internal gain of about 2.5. With the same experimental setup, the electronic jitter was found to be between 50 ps and 150 ps, depending on the signal amplitude. Moreover, the analysis of a test beam performed at the Proton Synchrotron (PS) T10 facility of CERN with 10 GeV/c protons and pions indicated that the overall detector time resolution is in the range of 234 ps to 244 ps. Further TCAD investigations, based on the do** profile extracted from $C(V)$ measurements, confirmed the multiplication gain measured on the test devices. Finally, TCAD simulations were used to tune the future do** concentration of the gain layer implant, targeting sensors with a higher avalanche gain. This adjustment is expected to enhance the timing performance of the sensors of the future productions, in order to cope with the high event rate expected in most of the near future high-energy and high-luminosity physics experiments, where the time resolution will be essential to disentangle overlap** events and it will also be crucial for Particle IDentification (PID).
△ Less
Submitted 28 June, 2024;
originally announced June 2024.
-
The EUSO-SPB2 Fluorescence Telescope for the Detection of Ultra-High Energy Cosmic Rays
Authors:
James H. Adams Jr.,
Denis Allard,
Phillip Alldredge,
Luis Anchordoqui,
Anna Anzalone,
Matteo Battisti,
Alexander A. Belov,
Mario Bertaina,
Peter F. Bertone,
Sylvie Blin-Bondil,
Julia Burton,
Francesco S. Cafagna,
Marco Casolino,
Karel Černý,
Mark J. Christ,
Roberta Colalillo,
Hank J. Crawford,
Alexandre Creusot,
Austin Cummings,
Rebecca Diesing,
Alessandro Di Nola,
Toshikazu Ebisuzaki,
Johannes Eser,
Silvia Ferrarese,
George Filippatos
, et al. (57 additional authors not shown)
Abstract:
The Extreme Universe Space Observatory on a Super Pressure Balloon 2 (EUSO-SPB2) flew on May 13$^{\text{th}}$ and 14$^{\text{th}}$ of 2023. Consisting of two novel optical telescopes, the payload utilized next-generation instrumentation for the observations of extensive air showers from near space. One instrument, the fluorescence telescope (FT) searched for Ultra-High Energy Cosmic Rays (UHECRs)…
▽ More
The Extreme Universe Space Observatory on a Super Pressure Balloon 2 (EUSO-SPB2) flew on May 13$^{\text{th}}$ and 14$^{\text{th}}$ of 2023. Consisting of two novel optical telescopes, the payload utilized next-generation instrumentation for the observations of extensive air showers from near space. One instrument, the fluorescence telescope (FT) searched for Ultra-High Energy Cosmic Rays (UHECRs) by recording the atmosphere below the balloon in the near-UV with a 1~$μ$s time resolution using 108 multi-anode photomultiplier tubes with a total of 6,912 channels. Validated by pre-flight measurements during a field campaign, the energy threshold was estimated around 2~EeV with an expected event rate of approximately 1 event per 10 hours of observation. Based on the limited time afloat, the expected number of UHECR observations throughout the flight is between 0 and 2. Consistent with this expectation, no UHECR candidate events have been found. The majority of events appear to be detector artifacts that were not rejected properly due to a shortened commissioning phase. Despite the earlier-than-expected termination of the flight, data were recorded which provide insights into the detectors stability in the near-space environment as well as the diffuse ultraviolet emissivity of the atmosphere, both of which are impactful to future experiments.
△ Less
Submitted 19 June, 2024;
originally announced June 2024.
-
Tests and characterisation of the KI trigger for fast events on the EUSO-SPB2 Fluorescence Telescope
Authors:
Hiroko Miyamoto,
Matteo Battisti,
Alexander Belov,
Mario Bertaina,
Sylvie Blin,
Alxandre Creusot,
Johannes Eser,
George Filippatos,
Pavel Klimov,
Massimiliano Manfrin,
Marco Mignone,
Etienne Parizot,
Lech Wiktor Piotrowski,
Guillaume Prévôt,
Daniil Trofimov
Abstract:
The second generation Extreme Universe Space Observatory on a Super-Pressure Balloon (EUSO-SPB2) mission is a stratospheric balloon mission developed within the Joint Exploratory Missions for Extreme Universe Space Observatory (JEM-EUSO) program. The Fluorescence Telescope (FT) is one of the two separate Schmidt telescopes of EUSO-SPB2, which aims at measuring the fluorescence emission of extensiv…
▽ More
The second generation Extreme Universe Space Observatory on a Super-Pressure Balloon (EUSO-SPB2) mission is a stratospheric balloon mission developed within the Joint Exploratory Missions for Extreme Universe Space Observatory (JEM-EUSO) program. The Fluorescence Telescope (FT) is one of the two separate Schmidt telescopes of EUSO-SPB2, which aims at measuring the fluorescence emission of extensive air showers from cosmic rays above the energy of 1 EeV, looking downwards onto the atmosphere from the float altitude of 33 km. The FT measures photons with a time resolution of 1.05 $μ$s in two different modes: single photon counting (PC) and charge integration (KI). In this paper, we describe the latter and report on the measurements of its characteristics. We also present a new trigger based on this channel, the so-called KI trigger, which allows to measure additional types of events, namely very short and intense light pulses. We report on the tests of this trigger mode in the laboratory and at the TurLab facility, and its implementation in the EUSO-SPB2 mission.
△ Less
Submitted 11 October, 2023;
originally announced October 2023.
-
An end-to-end calibration of the Mini-EUSO detector in space
Authors:
Hiroko Miyamoto,
Matteo Battisti,
Dario Barghini,
Alexander Belov,
Mario Bertaina,
Marta Bianciotto,
Francesca Bisconti,
Carl Blaksley,
Sylvie Blin,
Karl Bolmgren,
Giorgio Cambiè,
Francesca Capel,
Marco Casolino,
Igor Churilo,
Christophe De La taille,
Toshikazu Ebisuzaki,
Johannes Eser,
Francesco Fenu,
Geroge Filippatos,
Massimo Alberto Franceschi,
Christer Fuglesang,
Alessio Golzio,
Philippe Gorodetzky,
Fumioshi Ka**o,
Hiroshi Kasuga
, et al. (29 additional authors not shown)
Abstract:
Mini-EUSO is a wide Field-of-View (FoV, 44$^{\circ}$) telescope currently in operation from a nadia-facing UV-transparent window in the Russian Zvezda module on the International Space Station (ISS). It is the first detector of the JEM-EUSO program deployed on the ISS, launched in August 2019. The main goal of Mini-EUSO is to measure the UV emissions from the ground and atmosphere, using an orbita…
▽ More
Mini-EUSO is a wide Field-of-View (FoV, 44$^{\circ}$) telescope currently in operation from a nadia-facing UV-transparent window in the Russian Zvezda module on the International Space Station (ISS). It is the first detector of the JEM-EUSO program deployed on the ISS, launched in August 2019. The main goal of Mini-EUSO is to measure the UV emissions from the ground and atmosphere, using an orbital platform. Mini-EUSO is mainly sensitive in the 290-430 nm bandwidth. Light is focused by a system of two Fresnel lenses of 25 cm diameter each on the Photo- Detector-Module (PDM), which consists of an array of 36 Multi-Anode Photomultiplier Tubes (MAPMTs), for a total of 2304 pixels working in photon counting mode, in three different time resolutions of 2.5 $μ$s, 320 $μ$s, 40.96 ms operation in parallel. In the longest time scale, the data is continuously acquired to monitor the UV emission of the Earth. It is best suited for the observation of ground sources and therefore has been used for the observational campaigns of the Mini-EUSO. In this contribution, we present the assembled UV flasher, the operation of the field campaign and the analysis of the obtained data. The result is compared with the overall efficiency computed from the expectations which takes into account the atmospheric attenuation and the parameterization of different effects such as the optics efficiency, the MAPMT detection efficiency, BG3 filter transmittance and the transparency of the ISS window.
△ Less
Submitted 11 October, 2023;
originally announced October 2023.
-
Description and performance results of the trigger logic of TUS and Mini-EUSO to search for Ultra-High Energy Cosmic Rays from space
Authors:
M. Bertaina,
D. Barghini,
M. Battisti,
A. Belov,
M. Bianciotto,
F. Bisconti,
C. Blaksley,
K. Bolmgren,
G. Cambie,
F. Capel,
M. Casolino,
T. Ebisuzaki,
F. Fenu,
M. A. Franceschi,
C. Fuglesang,
A. Golzio,
P. Gorodetzky,
F. Ka**o,
P. Klimov,
M. Manfrin,
L. Marcelli,
W. Marszal,
M. Mignone,
H. Miyamoto,
T. Napolitano
, et al. (14 additional authors not shown)
Abstract:
The trigger logic of the Tracking Ultraviolet Setup (TUS) and Multiwavelength Imaging New Instrument for the Extreme Universe Space Observatory (Mini-EUSO) space-based projects of the Joint Experiment Missions - EUSO (JEM-EUSO) program is summarized. The performance results on the search for ultra-high energy cosmic rays are presented.
The trigger logic of the Tracking Ultraviolet Setup (TUS) and Multiwavelength Imaging New Instrument for the Extreme Universe Space Observatory (Mini-EUSO) space-based projects of the Joint Experiment Missions - EUSO (JEM-EUSO) program is summarized. The performance results on the search for ultra-high energy cosmic rays are presented.
△ Less
Submitted 29 October, 2022;
originally announced October 2022.
-
Data acquisition system for a 146-channel counter of protons in particle therapy
Authors:
S. Giordanengo,
M. Abujami,
C. Galeone,
S. Garbolino,
O. A. Martì Villarreal,
F. Mas Milian,
G. Mazza,
M. Mignone,
A. Vignati,
R. Wheadon,
R. Cirio,
V. Monaco,
R. Sacchi
Abstract:
A prototype of proton counter was developed by the University and the National Institute for Nuclear Physics of Torino to be used as online fluence beam monitor in particle therapy. The single particle identification approach aims at increasing the sensitivity and readout speed with respect to the state-of-the-art gas ionization chambers. The sensitive area is 2,7 x 2,7 cm^2 to cover the clinical…
▽ More
A prototype of proton counter was developed by the University and the National Institute for Nuclear Physics of Torino to be used as online fluence beam monitor in particle therapy. The single particle identification approach aims at increasing the sensitivity and readout speed with respect to the state-of-the-art gas ionization chambers. The sensitive area is 2,7 x 2,7 cm^2 to cover the clinical beam cross section characterized by a full width at half maximum of about 1 cm at the isocenter. The sensor is a thin Low Gain Avalanche Diode segmented in 146 strips with 180 micrometer pitch and with 50 micrometer active thickness, designed and produced by the Fondazione Bruno Kessler (Trento, Italy). The frontend readout to identify the single proton signal provided by each strip is based on a 24channel custom ASICs, named ABACUS, optimized to discriminate the signal pulses in a wide charge range (3-150 fC) with a maximum dead-time of 10 ns. With these specifications, at the maximum fluence rate of 10^8 p/(cm^2s) in the clinical energy range (60-230 MeV) and considering the silicon strips described above, a maximum pileup counting inefficiency less than 1 percent is achieved. A frontend board housing 6 ABACUS chips to readout the 146 strips was developed, the digital outputs being sent to 3 FPGAs (Kintex7) for the counting. A LabVIEW program implements the interface with the FPGAs, displays online the counting rate from each strip and stores the data for offline analysis.
△ Less
Submitted 6 May, 2022;
originally announced May 2022.
-
The Mini-EUSO telescope on board the International Space Station: Launch and first results
Authors:
M Casolino,
D Barghini,
M Battisti,
A Belov,
M Bertaina,
F Bisconti,
C Blaksley,
K Bolmgren,
F Cafagna,
G Cambiè,
F Capel,
T Ebisuzaki,
F Fenu,
A Franceschi,
C Fuglesang,
A Golzio,
P Gorodetzki,
F Ka**o,
H Kasuga,
P Klimov,
V. Kungel,
M Manfrin,
W Marszał,
H Miyamoto,
M Mignone
, et al. (14 additional authors not shown)
Abstract:
Mini-EUSO is a telescope launched on board the International Space Station in 2019 and currently located in the Russian section of the station. Main scientific objectives of the mission are the search for nuclearites and Strange Quark Matter, the study of atmospheric phenomena such as Transient Luminous Events, meteors and meteoroids, the observation of sea bioluminescence and of artificial satell…
▽ More
Mini-EUSO is a telescope launched on board the International Space Station in 2019 and currently located in the Russian section of the station. Main scientific objectives of the mission are the search for nuclearites and Strange Quark Matter, the study of atmospheric phenomena such as Transient Luminous Events, meteors and meteoroids, the observation of sea bioluminescence and of artificial satellites and man-made space debris. It is also capable of observing Extensive Air Showers generated by Ultra-High Energy Cosmic Rays with an energy above 10$^{21}$ eV and detect artificial showers generated with lasers from the ground. Mini-EUSO can map the night-time Earth in the UV range (290 - 430 nm), with a spatial resolution of about 6.3 km and a temporal resolution of 2.5 $μ$s, observing our planet through a nadir-facing UV-transparent window in the Russian Zvezda module. The instrument, launched on 2019/08/22 from the Baikonur cosmodrome, is based on an optical system employing two Fresnel lenses and a focal surface composed of 36 Multi-Anode Photomultiplier tubes, 64 channels each, for a total of 2304 channels with single photon counting sensitivity and an overall field of view of 44$^{\circ}$. Mini-EUSO also contains two ancillary cameras to complement measurements in the near infrared and visible ranges. In this paper we describe the detector and present the various phenomena observed in the first year of operation.
△ Less
Submitted 4 January, 2022;
originally announced January 2022.
-
Towards observations of nuclearites in Mini-EUSO
Authors:
L. W. Piotrowski,
D. Barghini,
M. Battisti,
A. Belov,
M. Bertaina,
F. Bisconti,
C. Blaksley,
K. Bolmgren,
F. Cafagna,
G. Cambiè,
F. Capel,
M. Casolino,
T. Ebisuzaki,
F. Fenu,
A. Franceschi,
C. Fuglesang,
A. Golzio,
P. Gorodetzki,
F. Ka**o,
H. Kasuga,
P. Klimov,
V. Kungel,
M. Manfrin,
L. Marcelli,
W. Marszał
, et al. (16 additional authors not shown)
Abstract:
Mini-EUSO is a small orbital telescope with a field of view of $44^{\circ}\times 44^{\circ}$, observing the night-time Earth mostly in 320-420 nm band. Its time resolution spanning from microseconds (triggered) to milliseconds (untriggered) and more than $300\times 300$ km of the ground covered, already allowed it to register thousands of meteors. Such detections make the telescope a suitable tool…
▽ More
Mini-EUSO is a small orbital telescope with a field of view of $44^{\circ}\times 44^{\circ}$, observing the night-time Earth mostly in 320-420 nm band. Its time resolution spanning from microseconds (triggered) to milliseconds (untriggered) and more than $300\times 300$ km of the ground covered, already allowed it to register thousands of meteors. Such detections make the telescope a suitable tool in the search for hypothetical heavy compact objects, which would leave trails of light in the atmosphere due to their high density and speed. The most prominent example are the nuclearites -- hypothetical lumps of strange quark matter that could be stabler and denser than the nuclear matter. In this paper, we show potential limits on the flux of nuclearites after collecting 42 hours of observations data.
△ Less
Submitted 4 January, 2022;
originally announced January 2022.
-
Development of a cosmic ray oriented trigger for the fluorescence telescope on EUSO-SPB2
Authors:
George Filippatos,
Matteo Battisti,
Alexander Belov,
Mario Bertaina,
Francesca Bisconti,
Johannes Eser,
Marco Mignone,
Fred Sarazin,
Lawrence Wiencke
Abstract:
The Extreme Universe Space Observatory on a Super Pressure Balloon 2 (EUSO-SPB2), in preparation, aims to make the first observations of Ultra-High Energy Cosmic Rays (UHECRs) from near space using optical techniques. EUSO-SPB2 will prototype instrumentation for future satellite-based missions, including the Probe of Extreme Multi-Messenger Astrophysics (POEMMA) and K-EUSO. The payload will consis…
▽ More
The Extreme Universe Space Observatory on a Super Pressure Balloon 2 (EUSO-SPB2), in preparation, aims to make the first observations of Ultra-High Energy Cosmic Rays (UHECRs) from near space using optical techniques. EUSO-SPB2 will prototype instrumentation for future satellite-based missions, including the Probe of Extreme Multi-Messenger Astrophysics (POEMMA) and K-EUSO. The payload will consist of two telescopes. The first is a Cherenkov telescope (CT) being developed to quantify the background for future below-the-limb very high energy (E>10 PeV) astrophysical neutrino observations, and the second is a fluorescence telescope (FT) being developed for detection of UHECRs. The FT will consist of a Schmidt telescope, and a 6192 pixel ultraviolet camera with an integration time of 1.05 microseconds. The first step in the data acquisition process for the FT is a hardware level trigger in order to decide which data to record. In order to maximize the number of UHECR induced extensive air showers (EASs) which can be detected, a novel trigger algorithm has been developed based on the intricacies and limitations of the detector. The expected performance of the trigger has been characterized by simulations and, pending hardware verification, shows that EUSO-SPB2 is well positioned to attempt the first near-space observation of UHECRs via optical techniques.
△ Less
Submitted 7 October, 2022; v1 submitted 3 January, 2022;
originally announced January 2022.
-
EUSO@TurLab project in view of Mini-EUSO and EUSO-SPB2 missions
Authors:
H. Miyamoto,
M. E. Bertaina,
D. Barghini,
M. Battisti,
A. Belov,
F. Bisconti,
S. Blin-Bondil,
K. Bolmgren,
G. Cambie,
F. Capel,
R. Caruso,
M. Casolino,
I. Churilo,
G. Contino,
G. Cotto,
T. Ebisuzaki,
F. Fenu,
C. Fuglesang,
A. Golzio,
P. Gorodetzky,
F. Ka**o,
P. Klimov,
M. Manfrin,
L. Marcelli,
M. Marengo
, et al. (15 additional authors not shown)
Abstract:
The TurLab facility is a laboratory, equipped with a 5 m diameter and 1 m depth rotating tank, located in the fourth basement level of the Physics Department of the University of Turin. In the past years, we have used the facility to perform experiments related to the observations of Extreme Energy Cosmic Rays (EECRs) from space using the fluorescence technique for JEM- EUSO missions with the main…
▽ More
The TurLab facility is a laboratory, equipped with a 5 m diameter and 1 m depth rotating tank, located in the fourth basement level of the Physics Department of the University of Turin. In the past years, we have used the facility to perform experiments related to the observations of Extreme Energy Cosmic Rays (EECRs) from space using the fluorescence technique for JEM- EUSO missions with the main objective to test the response of the trigger logic. In the missions, the diffuse night brightness and artificial and natural light sources can vary significantly in time and space in the Field of View (FoV) of the telescope. Therefore, it is essential to verify the detector performance and test the trigger logic under such an environment. By means of the tank rotation, a various terrestrial surface with the different optical characteristics such as ocean, land, forest, desert and clouds, as well as artificial and natural light sources such as city lights, lightnings and meteors passing by the detector FoV one after the other is reproduced. The fact that the tank located in a very dark place enables the tests under an optically controlled environment. Using the Mini-EUSO data taken since 2019 onboard the ISS, we will report on the comparison between TurLab and ISS measurements in view of future experiments at TurLab. Moreover, in the forthcoming months we will start testing the trigger logic of the EUSO-SPB2 mission. We report also on the plans and status for this purpose.
△ Less
Submitted 23 December, 2021;
originally announced December 2021.
-
Simulations studies for the Mini-EUSO detector
Authors:
H. Miyamoto,
F. Fenu,
D. Barghini,
M. Battisti,
A. Belov,
M. E. Bertaina,
F. Bisconti,
R. Bonino,
G. Cambie,
F. Capel,
M. Casolino,
I. Churilo,
T. Ebisuzaki,
C. Fuglesang,
A. Golzio,
P. Gorodetzky,
F. Ka**o,
P. Klimov,
M. Manfrin,
L. Marcelli,
W. Marszał,
M. Mignone,
E. Parizot,
P. Picozza,
L. W. Piotrowski
, et al. (9 additional authors not shown)
Abstract:
Mini-EUSO is a mission of the JEM-EUSO program flying onboard the International Space Station since August 2019. Since the first data acquisition in October 2019, more than 35 sessions have been performed for a total of 52 hours of observations. The detector has been observing Earth at night-time in the UV range and detected a wide variety of transient sources all of which have been modelled throu…
▽ More
Mini-EUSO is a mission of the JEM-EUSO program flying onboard the International Space Station since August 2019. Since the first data acquisition in October 2019, more than 35 sessions have been performed for a total of 52 hours of observations. The detector has been observing Earth at night-time in the UV range and detected a wide variety of transient sources all of which have been modelled through Monte Carlo simulations. Mini-EUSO is also capable of detecting meteors and potentially space debris and we performed simulations for such events to estimate their impact on future missions for cosmic ray science from space. We show here examples of the simulation work done in this framework to analyse the Mini-EUSO data. The expected response of Mini-EUSO with respect to ultra high energy cosmic ray showers has been studied. The efficiency curve of Mini-EUSO as a function of primary energy has been estimated and the energy threshold for Cosmic Rays has been placed to be above 10^{21} eV. We compared the morphology of several transient events detected during the mission with cosmic ray simulations and excluded that they can be due to cosmic ray showers. To validate the energy threshold of the detector, a system of ground based flashers is being used for end-to-end calibration purposes. We therefore implemented a parameterisation of such flashers into the JEM-EUSO simulation framework and studied the response of the detector with respect to such sources.
△ Less
Submitted 23 December, 2021;
originally announced December 2021.
-
Observation of ELVES with Mini-EUSO telescope on board the International Space Station
Authors:
Laura Marcelli,
Enrico Arnone,
Matteo Barghini,
Matteo Battisti,
Alexander Belov,
Mario Bertaina,
Carl Blaksley,
Karl Bolmgren,
Giorgio Cambiè,
Francesca Capel,
Marco Casolino,
Toshikazu Ebisuzaki,
Christer Fuglesang,
Philippe Gorodetzki,
Fumiyoshi Ka**o,
Pavel Klimov,
Wlodzimierz Marszał,
Marco Mignone,
Etienne Parizot,
Piergiorgio Picozza,
Lech Wictor Piotrowski,
Zbigniew Plebaniak,
Guilliame Prévôt,
Giulia Romoli,
Enzo Reali
, et al. (5 additional authors not shown)
Abstract:
Mini-EUSO is a detector observing the Earth in the ultraviolet band from the International Space Station through a nadir-facing window, transparent to the UV radiation, in the Russian Zvezda module. Mini-EUSO main detector consists in an optical system with two Fresnel lenses and a focal surface composed of an array of 36 Hamamatsu Multi-Anode Photo-Multiplier tubes, for a total of 2304 pixels, wi…
▽ More
Mini-EUSO is a detector observing the Earth in the ultraviolet band from the International Space Station through a nadir-facing window, transparent to the UV radiation, in the Russian Zvezda module. Mini-EUSO main detector consists in an optical system with two Fresnel lenses and a focal surface composed of an array of 36 Hamamatsu Multi-Anode Photo-Multiplier tubes, for a total of 2304 pixels, with single photon counting sensitivity. The telescope also contains two ancillary cameras, in the near infrared and visible ranges, to complement measurements in these bandwidths. The instrument has a field of view of 44 degrees, a spatial resolution of about 6.3 km on the Earth surface and of about 4.7 km on the ionosphere. The telescope detects UV emissions of cosmic, atmospheric and terrestrial origin on different time scales, from a few micoseconds upwards. On the fastest timescale of 2.5 microseconds, Mini-EUSO is able to observe atmospheric phenomena as Transient Luminous Events and in particular the ELVES, which take place when an electromagnetic wave generated by intra-cloud lightning interacts with the ionosphere, ionizing it and producing apparently superluminal expanding rings of several 100 km and lasting about 100 microseconds. These highly energetic fast events have been observed to be produced in conjunction also with Terrestrial Gamma-Ray Flashes and therefore a detailed study of their characteristics (speed, radius, energy...) is of crucial importance for the understanding of these phenomena. In this paper we present the observational capabilities of ELVE detection by Mini-EUSO and specifically the reconstruction and study of ELVE characteristics.
△ Less
Submitted 15 December, 2021;
originally announced December 2021.
-
The CGEM-IT readout chain
Authors:
A. Amoroso,
R. Baldini Ferroli,
I. Balossino,
M. Bertani,
D. Bettoni,
F. Bianchi,
A. Bortone,
R. Bugalho,
A. Calcaterra,
S. Cerioni,
S. Chiozzi,
G. Cibinetto,
A. Cotta Ramusino,
F. Cossio,
M. Da Rocha Rolo,
F. De Mori,
M. Destefanis,
A. Di Francesco,
F. Evangelisti,
R. Farinelli,
L. Fava,
G. Felici,
S. Garbolino,
I. Garzia,
M. Gatta
, et al. (22 additional authors not shown)
Abstract:
An innovative Cylindrical Gas Electron Multiplier (CGEM) detector is under construction for the upgrade of the inner tracker of the BESIII experiment. A novel system has been worked out for the readout of the CGEM detector, including a new ASIC, dubbed TIGER -Torino Integrated GEM Electronics for Readout, designed for the amplification and digitization of the CGEM output signals. The data output b…
▽ More
An innovative Cylindrical Gas Electron Multiplier (CGEM) detector is under construction for the upgrade of the inner tracker of the BESIII experiment. A novel system has been worked out for the readout of the CGEM detector, including a new ASIC, dubbed TIGER -Torino Integrated GEM Electronics for Readout, designed for the amplification and digitization of the CGEM output signals. The data output by TIGER are collected and processed by a first FPGA-based module, GEM Read Out Card, in charge of configuration and control of the front-end ASICs. A second FPGA-based module, named GEM Data Concentrator, builds the trigger selected event packets containing the data and stores them via the main BESIII data acquisition system. The design of the electronics chain, including the power and signal distribution, will be presented together with its performance.
△ Less
Submitted 17 August, 2021; v1 submitted 19 May, 2021;
originally announced May 2021.
-
Mini-EUSO mission to study Earth UV emissions on board the ISS
Authors:
S. Bacholle,
P. Barrillon,
M. Battisti,
A. Belov,
M. Bertaina,
F. Bisconti,
C. Blaksley,
S. Blin-Bondil,
F. Cafagna,
G. Cambiè,
F. Capel,
M. Casolino,
M. Crisconio,
I. Churilo,
G. Cotto,
C. de la Taille,
A. Djakonow,
T. Ebisuzaki,
F. Fenu,
A. Franceschi,
C. Fuglesang,
P. Gorodetzky,
A. Haungs,
F. Ka**o,
H. Kasuga
, et al. (35 additional authors not shown)
Abstract:
Mini-EUSO is a telescope observing the Earth in the ultraviolet band from the International Space Station. It is a part of the JEM-EUSO program, paving the way to future larger missions, such as KEUSO and POEMMA, devoted primarily to the observation of Ultra High Energy Cosmic Rays from space. Mini-EUSO is capable of observing Extensive Air Showers generated by Ultra-High Energy Cosmic Rays with a…
▽ More
Mini-EUSO is a telescope observing the Earth in the ultraviolet band from the International Space Station. It is a part of the JEM-EUSO program, paving the way to future larger missions, such as KEUSO and POEMMA, devoted primarily to the observation of Ultra High Energy Cosmic Rays from space. Mini-EUSO is capable of observing Extensive Air Showers generated by Ultra-High Energy Cosmic Rays with an energy above 10^21 eV and detect artificial showers generated with lasers from the ground. Other main scientific objectives of the mission are the search for nuclearites and Strange Quark Matter, the study of atmospheric phenomena such as Transient Luminous Events, meteors and meteoroids, the observation of sea bioluminescence and of artificial satellites and man-made space debris. Mini-EUSO will map the night-time Earth in the UV range (290 - 430 nm), with a spatial resolution of about 6.3 km and a temporal resolution of 2.5 microseconds, through a nadir-facing UV-transparent window in the Russian Zvezda module. The instrument, launched on August 22, 2019 from the Baikonur cosmodrome, is based on an optical system employing two Fresnel lenses and a focal surface composed of 36 Multi-Anode Photomultiplier tubes, 64 channels each, for a total of 2304 channels with single photon counting sensitivity and an overall field of view of 44 degrees. Mini-EUSO also contains two ancillary cameras to complement measurements in the near infrared and visible ranges. In this paper we describe the detector and present the various phenomena observed in the first months of operations.
△ Less
Submitted 5 October, 2020;
originally announced October 2020.
-
Mini-EUSO experiment to study UV emission of terrestrial and astrophysical origin onboard of the International Space Station
Authors:
M. Casolino,
M. Battisti,
A. Belov,
M. Bertaina,
F. Bisconti,
S. Blin-Bondil,
F. Cafagna,
G. Cambiè,
F. Capel,
I. Churilo,
G. Cotto,
A. Djakonow,
T. Ebisuzaki,
F. Fausti,
F. Fenu,
C. Fornaro,
A. Franceschi,
C. Fuglesang,
P. Gorodetzky,
A. Haungs,
F. Ka**o,
P. Klimov,
L. Marcelli,
W. Marszał,
M. Mignone
, et al. (20 additional authors not shown)
Abstract:
Mini-EUSO will observe the Earth in the UV range (300 - 400 nm) offering the opportunity to study a variety of atmospheric events such as Transient Luminous Events (TLEs), meteors and marine bioluminescence. Furthermore it aims to search for Ultra High Energy Cosmic Rays (UHECR) above $10^{21}$ eV and Strange Quark Matter (SQM). The detector is expected to be launched to the International Space St…
▽ More
Mini-EUSO will observe the Earth in the UV range (300 - 400 nm) offering the opportunity to study a variety of atmospheric events such as Transient Luminous Events (TLEs), meteors and marine bioluminescence. Furthermore it aims to search for Ultra High Energy Cosmic Rays (UHECR) above $10^{21}$ eV and Strange Quark Matter (SQM). The detector is expected to be launched to the International Space Station in August 2019 and look at the Earth in nadir mode from the UV-transparent window of the Zvezda module of the International Space Station.
The instrument comprises a compact telescope with a large field of view ($44^{\circ}$), based on an optical system employing two Fresnel lenses for light collection. The light is focused onto an array of 36 multi-anode photomultiplier tubes (MAPMT), for a total of 2304 pixels and the resulting signal is converted into digital, processed and stored via the electronics subsystems on-board. In addition to the main detector, Mini-EUSO contains two ancillary cameras for complementary measurements in the near infrared (1500 - 1600 nm) and visible (400 - 780 nm) range and also a 8x8 SiPM imaging array.
△ Less
Submitted 27 September, 2019;
originally announced September 2019.
-
Space Debris detection and tracking with the techniques of cosmic ray physics
Authors:
H. Miyamoto,
M. Battisti,
A. Belov,
M. E. Bertaina,
F. Bisconti,
R. Bonino,
S. Blin-Bondil,
F. Cafagna,
G. Cambiè,
F. Capel,
M. Casolino,
A. Cellino,
I. Churilo,
G. Cotto,
A. Djakonow,
T. Ebisuzaki,
F. Fausti,
F. Fenu,
C. Fornaro,
A. Franceschi,
C. Fuglesang,
D. Gardiol,
P. Gorodetzky,
F. Ka**o,
P. Klimov
, et al. (23 additional authors not shown)
Abstract:
Space Debris (SD) consist of non-operational artificial objects orbiting around the Earth, which could possibly damage space vehicles, such as the International Space Station (ISS) or other manned spacecrafts. The vast majority of such objects are cm-sized, not catalogued and usually the tracking data are not precise enough. Here we present the feasibility study of SD detection and tracking with t…
▽ More
Space Debris (SD) consist of non-operational artificial objects orbiting around the Earth, which could possibly damage space vehicles, such as the International Space Station (ISS) or other manned spacecrafts. The vast majority of such objects are cm-sized, not catalogued and usually the tracking data are not precise enough. Here we present the feasibility study of SD detection and tracking with techniques usually employed in cosmic-ray physics. For this purpose, we have evaluated the possibility of using Mini-EUSO, a space-borne fluorescence telescope to be deployed on the ISS, to track SD illuminated by the Sun. By means of ESAF (EUSO Simulation and analysis Framework) simulation and by develo** the trigger algorithms, we estimated the minimum size and maximum distances of detectable SD. We then studied the number of possible SD detections using an ESA software called MASTER (Meteoroid and SD Terrestrial Environment Reference). With the Mini-EUSO Engineering Model (Mini-EUSO EM), we performed some measurements to estimate the reflectance of the most common SD materials and to demonstrate the ability of Mini-EUSO to detect SD events. We also performed some tests in open-sky conditions, identifying and tracking fast-moving objects. In particular, the detection of a rocket body allowed us to confirm the simulation outcomes predictions and the expected performance of the detector.
△ Less
Submitted 12 September, 2019;
originally announced September 2019.
-
Trigger developments for the fluorescence detector of EUSO-TA and EUSO-SPB2
Authors:
M. Battisti,
M. Bertaina,
F. Fenu,
H. Miyamoto,
K. Shinozaki,
A. Belov,
F. Bisconti,
M. Mignone,
F. Capel
Abstract:
The JEM-EUSO program aims at detecting Ultra High Energy Cosmic Rays (UHECRs) by observing the fluorescence light produced by extensive air showers (EAS) in the Earth's atmosphere. Within this program, a new generation of missions is being built, including (i) Mini-EUSO that will be installed on board the ISS in August 2019, (ii) an upgrade to the ground-based telescope EUSO-TA and (iii) the secon…
▽ More
The JEM-EUSO program aims at detecting Ultra High Energy Cosmic Rays (UHECRs) by observing the fluorescence light produced by extensive air showers (EAS) in the Earth's atmosphere. Within this program, a new generation of missions is being built, including (i) Mini-EUSO that will be installed on board the ISS in August 2019, (ii) an upgrade to the ground-based telescope EUSO-TA and (iii) the second super pressure balloon flight (EUSO-SPB2). All these detectors will have a dedicated trigger system based on a board equipped with a Xilinx Zynq device that will be able to detect different types of events on three different time-scales: a microsecond time-scale for cosmic ray detection (L1), a hundreds of microsecond time-scale for slower events like transient luminous events (TLEs) (L2), and a tens of millisecond time-scale used to produce a continuous monitoring, for even slower events like meteors or nuclearites. The L1 trigger logic for the upgrade of EUSO-TA and EUSO-SPB2 are being developed taking into account the peculiarity of each detector (optic system, FOV, frame length) starting from the logic already developed for Mini-EUSO. In particular, every pixel will have an independent threshold that will be dynamically adapted to the level of the background; a predetermined condition on the number, the position and the time distribution of pixels above threshold has to be satisfied in order to issue a trigger. This contribution will summarize the L1 trigger logics and the tests currently performed.
△ Less
Submitted 12 September, 2019;
originally announced September 2019.
-
Mini-EUSO engineering model: tests in open-sky condition
Authors:
F. Bisconti,
D. Barghini,
M. Battisti,
A. Belov,
M. E. Bertaina,
S. Blin-Bondil,
F. Cafagna,
G. Cambiè,
F. Capel,
M. Casolino,
A. Cellino,
I. Churilo,
G. Cotto,
A. Djakonow,
T. Ebisuzaki,
F. Fausti,
F. Fenu,
C. Fornaro,
A. Franceschi,
C. Fuglesang,
D. Gardiol,
P. Gorodetzky,
F. Ka**o,
P. Klimov,
L. Marcelli
, et al. (23 additional authors not shown)
Abstract:
Mini-EUSO is a UV telescope that will look downwards to the Earth's atmosphere onboard the International Space Station. With the design of the ultra-high energy cosmic ray fluorescence detectors belonging to the JEM-EUSO program, it will make the first UV map of the Earth by observing atmospheric phenomena such as transient luminous events, sprites and lightning, as well as meteors and bioluminesc…
▽ More
Mini-EUSO is a UV telescope that will look downwards to the Earth's atmosphere onboard the International Space Station. With the design of the ultra-high energy cosmic ray fluorescence detectors belonging to the JEM-EUSO program, it will make the first UV map of the Earth by observing atmospheric phenomena such as transient luminous events, sprites and lightning, as well as meteors and bioluminescence from earth. Diffused light from laser shots from the ground, which mimic the fluorescence light emitted by Nitrogen molecules when extensive air showers pass through the atmosphere, can be used to verify the capability of this kind of detector to observe ultra-high energy cosmic rays. To validate the electronics and the trigger algorithms developed for Mini-EUSO, a scaled down version of the telescope with 1:9 of the original focal surface and a lens of 2.5 cm diameter has been built. Tests of the Mini-EUSO engineering model have been made in laboratory and in open sky condition. In this paper, we report results of observations of the night sky, which include the detection of stars, meteors, a planet and a rocket body reflecting the sunlight. Interesting results of the observation of city lights are also reported.
△ Less
Submitted 6 September, 2019;
originally announced September 2019.
-
The EUSO@TurLab: Test of Mini-EUSO Engineering Model
Authors:
H. Miyamoto,
M. Battisti,
A. Belov,
M. E. Bertaina,
F. Bisconti,
R. Bonino,
S. Blin-Bondil,
F. Cafagna,
G. Cambiè,
F. Capel,
R. Caruso,
M. Casolino,
A. Cellino,
I. Churilo,
G. Contino,
G. Cotto,
A. Djakonow,
T. Ebisuzaki,
F. Fausti,
F. Fenu,
C. Fornaro,
A. Franceschi,
C. Fuglesang,
D. Gardiol,
P. Gorodetzky
, et al. (25 additional authors not shown)
Abstract:
The TurLab facility is a laboratory, equipped with a 5 m diameter and 1 m depth rotating tank, located in the Physics Department of the University of Turin. Originally, it was mainly built to study systems of different scales where rotation plays a key role in the fluid behavior such as in atmospheric and oceanic flows. In the past few years the TurLab facility has been used to perform experiments…
▽ More
The TurLab facility is a laboratory, equipped with a 5 m diameter and 1 m depth rotating tank, located in the Physics Department of the University of Turin. Originally, it was mainly built to study systems of different scales where rotation plays a key role in the fluid behavior such as in atmospheric and oceanic flows. In the past few years the TurLab facility has been used to perform experiments related to the observation of Extreme Energy Cosmic Rays (EECRs) from space using the fluorescence technique. For example, in the case of the JEM-EUSO mission, where the diffuse night brightness and artificial light sources can vary significantly in time and space inside the Field of View of the telescope. The Focal Surface of Mini-EUSO Engineering Model (Mini-EUSO EM) with the level 1 (L1) and 2 (L2) trigger logics implemented in the Photo-Detector Module (PDM) has been tested at TurLab. Tests related to the possibility of using an EUSO-like detector for other type of applications such as Space Debris (SD) monitoring and imaging detector have also been pursued. The tests and results obtained within the EUSO@TurLab Project on these different topics are presented.
△ Less
Submitted 5 September, 2019;
originally announced September 2019.
-
Triple GEM performance in magnetic field
Authors:
M. Alexeev,
A. Amoroso,
S. Bagnasco,
R. Baldini Ferroli,
I. Balossino,
G. Bencivenni,
M. Bertani,
D. Bettoni,
F. Bianchi,
A. Bortone,
A. Calcaterra,
M. Capodiferro,
V. Carassiti,
S. Cerioni,
J. Chai,
W. Cheng,
S. Chiozzi,
G. Cibinetto,
A. Cotta Ramusino,
G. Cotto,
F. Cossio,
M. Da Rocha Rolo,
F. De Mori,
M. Destefanis,
D. Domenici
, et al. (43 additional authors not shown)
Abstract:
Performance of triple GEM prototypes in strong magnetic field has been evaluated bymeans of a muon beam at the H4 line of the SPS test area at CERN. Data have been reconstructedand analyzed offline with two reconstruction methods: the charge centroid and the micro-Time-Projection-Chamber exploiting the charge and the time measurement respectively. A combinationof the two reconstruction methods is…
▽ More
Performance of triple GEM prototypes in strong magnetic field has been evaluated bymeans of a muon beam at the H4 line of the SPS test area at CERN. Data have been reconstructedand analyzed offline with two reconstruction methods: the charge centroid and the micro-Time-Projection-Chamber exploiting the charge and the time measurement respectively. A combinationof the two reconstruction methods is capable to guarantee a spatial resolution better than 150μmin magnetic field up to a 1 T.
△ Less
Submitted 17 August, 2019;
originally announced August 2019.
-
GRAAL: Gem Reconstruction And Analysis Library
Authors:
R. Farinelli,
M. Alexeev,
A. Amoroso,
S. Bagnasco,
R. BaldiniFerroli,
I. Balossino,
M. Bertani,
D. Bettoni,
A. Bortone,
F. Bianchi,
A. Calcaterra,
S. Cerioni,
J. Chai,
W. Cheng,
S. Chiozzi,
G. Cibinetto,
F. Cossio,
A. Cotta Ramusino,
G. Cotto,
M. Da Rocha Rolo,
F. De Mori,
M. Destefanis,
F. Evangelisti,
L. Fava,
G. Felici
, et al. (25 additional authors not shown)
Abstract:
MPGD are the new frontier in gas trackers. Among this kind of devices, theGEM chambers are widely used. The experimental signals acquired with the detector mustobviously be reconstructed and analysed. In this contribution, a new offline software to performreconstruction, alignment and analysis on the data collected with APV-25 and TIGER ASICswill be presented. GRAAL (Gem Reconstruction And Analysi…
▽ More
MPGD are the new frontier in gas trackers. Among this kind of devices, theGEM chambers are widely used. The experimental signals acquired with the detector mustobviously be reconstructed and analysed. In this contribution, a new offline software to performreconstruction, alignment and analysis on the data collected with APV-25 and TIGER ASICswill be presented. GRAAL (Gem Reconstruction And Analysis Library) is able to measurethe performance of a MPGD detector with a strip segmented anode (presently). The code isdivided in three parts: reconstruction, where the hits are digitized and clusterized; tracking,where a procedure fits the points from the tracking system and uses that information to align thechamber with rotations and shifts; analysis, where the performance is evaluated (e.g. efficiency,spatial resolution,etc.). The user must set the geometry of the setup and then the programreturns automatically the analysis results, taking care of different conditions of gas mixture,electric field, magnetic field, geometries, strip orientation, dead strip, misalignment and manyothers.
△ Less
Submitted 8 May, 2019;
originally announced May 2019.
-
A fast and parametric digitization for triple-GEM detectors
Authors:
R. Farinelli,
M. Alexeev,
A. Amoroso,
S. Bagnasco,
R. Baldini Ferrioli,
I. Balossino,
M. Bertani,
D. Bettoni,
A. Bortone,
F. Bianchi,
A. Calcaterra,
S. Cerioni,
J. Chai,
W. Cheng,
S. Chiozzi,
G. Cibinetto,
F. Cossio,
A. Cotta Ramusino,
G. Cotto,
M. Da Rocha Rolo,
F. De Mori,
M. Destefanis,
F. Evangelisti,
L. Fava,
G. Felici
, et al. (26 additional authors not shown)
Abstract:
Triple-GEM detectors are a well known technology in high energy physics. In order to have a complete understanding of their behavior, in parallel with on beam testing, a Monte Carlo code has to be developed to simulate their response to the passage of particles. The software must take into account all the physical processes involved from the primary ionization up to the signal formation, e.g. the…
▽ More
Triple-GEM detectors are a well known technology in high energy physics. In order to have a complete understanding of their behavior, in parallel with on beam testing, a Monte Carlo code has to be developed to simulate their response to the passage of particles. The software must take into account all the physical processes involved from the primary ionization up to the signal formation, e.g. the avalanche multiplication and the effect of the diffusion on the electrons. In the case of gas detectors, existing software such as Garfield already perform a very detailed simulation but are CPU time consuming. A description of a reliable but faster simulation is presented here: it uses a parametric description of the variables of interest obtained by suitable preliminary Garfield simulations and tuned to the test beam data. It can reproduce the real values of the charge measured by the strip, needed to reconstruct the position with the Charge Centroid method. In addition, particular attention was put to the simulation of the timing information, which permits to apply also the micro-Time Projection Chamber position reconstruction, for the first time on a triple-GEM. A comparison between simulation and experimental values of some sentinel variables in different conditions of magnetic field, high voltage settings and incident angle will be shown.
△ Less
Submitted 12 April, 2019;
originally announced April 2019.
-
Design and performance of the TIGER front-end ASIC for the BESIII Cylindrical Gas Electron Multiplier detector
Authors:
Fabio Cossio,
Maxim Alexeev,
Ricardo Bugalho,
Junying Chai,
Weishuai Cheng,
Manuel D. Da Rocha Rolo,
Agostino Di Francesco,
Michela Greco,
Chongyang Leng,
Huaishen Li,
Marco Maggiora,
Simonetta Marcello,
Marco Mignone,
Angelo Rivetti,
Joao Varela,
Richard Wheadon
Abstract:
We present the design and characterization of TIGER (Turin Integrated Gem Electronics for Readout), a 64-channel ASIC developed for the readout of the CGEM (Cylindrical Gas Electron Multiplier) detector, the proposed inner tracker for the 2018 upgrade of the BESIII experiment, carried out at BEPCII in Bei**g. Each ASIC channel features a charge sensitive amplifier coupled to a dual-branch shaper…
▽ More
We present the design and characterization of TIGER (Turin Integrated Gem Electronics for Readout), a 64-channel ASIC developed for the readout of the CGEM (Cylindrical Gas Electron Multiplier) detector, the proposed inner tracker for the 2018 upgrade of the BESIII experiment, carried out at BEPCII in Bei**g. Each ASIC channel features a charge sensitive amplifier coupled to a dual-branch shaper stage, optimized for timing and charge measurement, followed by a mixed-mode back-end that extracts and digitizes the timestamp and charge of the input signals. The time-of-arrival is provided by a set of low-power TDCs, based on analogue interpolation techniques, while the charge measurement is obtained either from the Time-over-Threshold information or with a sample-and-hold circuit. The ASIC has been fabricated in a 110 nm CMOS technology and designed to operate with a 1.2 V power supply, an input capacitance of about 100 pF, an input dynamic range between 3 and 50 fC, a power consumption of about 12 mW/channel and a sustained event rate of 60 kHz/channel. The design and test results of TIGER first prototype are presented showing its full functionality.
△ Less
Submitted 13 March, 2019;
originally announced March 2019.
-
Innovative design and construction technique for the Cylindrical GEM detector for the BESIII experiment
Authors:
A. Amoroso,
M. Alexeev,
R. Baldini Ferroli,
M. Bertani,
D. Bettoni,
F. Bianchi,
A. Calcaterra,
N. Canale,
M. Capodiferro,
V. Carassiti,
S. Cerioni,
JY. Chai,
S. Chiozzi,
G. Cibinetto,
F. Cossio,
A. Cotta Ramusino,
F. De Mori,
M. Destefanis,
J. Dong,
F. Evangelisti,
R. Farinelli,
L. Fava,
G. Felici,
E. Fioravanti,
I. Garzia
, et al. (27 additional authors not shown)
Abstract:
Gas detector are very light instrument used in high energy physics to measure the particle properties: position and momentum. Through high electric field is possible to use the Gas Electron Multiplier (GEM) technology to detect the particles and to exploit the its properties to construct a large area detector, such as the new IT for BESIII. The state of the art in the GEM production allow to creat…
▽ More
Gas detector are very light instrument used in high energy physics to measure the particle properties: position and momentum. Through high electric field is possible to use the Gas Electron Multiplier (GEM) technology to detect the particles and to exploit the its properties to construct a large area detector, such as the new IT for BESIII. The state of the art in the GEM production allow to create very large area GEM foils (up to 50x100 cm2) and thanks to the small thickness of these foil is it possible to shape it to the desired form: a Cylindrical Gas Electron Multiplier (CGEM) is then proposed. The innovative construction technique based on Rohacell, a PMI foam, will give solidity to cathode and anode with a very low impact on material budget. The entire detector is sustained by permaglass rings glued at the edges. These rings are use to assembly the CGEM together with a dedicated Vertical Insertion System and moreover there is placed the On-Detector electronic. The anode has been improved w.r.t. the state of the art through a jagged readout that minimize the inter-strip capacitance. The mechanical challenge of this detector requires a precision of the entire geometry within few hundreds of microns in the whole area. In this presentation will be presented an overview of the construction technique and the validation of this technique through the realization of a CGEM and its first tests. These activities are performed within the framework of the BESIIICGEM Project (645664), funded by the European Commission in the action H2020-RISE-MSCA-2014.
△ Less
Submitted 21 March, 2018;
originally announced March 2018.
-
Test beam results of a Cylindrical GEM detector for the BESIII experiment
Authors:
G. Mezzadri,
M. Alexeev,
A. Amoroso,
R. Baldini Ferroli,
M. Bertani,
D. Bettoni,
F. Bianchi,
A. Calcaterra,
N. Canale,
M. Capodiferro,
V. Carassiti,
S. Cerioni,
JY. Chai,
S. Chiozzi,
G. Cibinetto,
F. Cossio,
A. Cotta Ramusino,
F. De Mori,
M. Destefanis,
J. Dong,
F. Evangelisti,
R. Farinelli,
L. Fava,
G. Felici,
E. Fioravanti
, et al. (28 additional authors not shown)
Abstract:
Gas detector are very light instrument used in high energy physics to measure the particle properties: position and momentum. Through high electric field is possible to use the Gas Electron Multiplier (GEM) technology to detect the charged particles and to exploit their properties to construct a large area detector, such as the new IT for BESIII. The state of the art in the GEM production allows t…
▽ More
Gas detector are very light instrument used in high energy physics to measure the particle properties: position and momentum. Through high electric field is possible to use the Gas Electron Multiplier (GEM) technology to detect the charged particles and to exploit their properties to construct a large area detector, such as the new IT for BESIII. The state of the art in the GEM production allows to create very large area GEM foils (up to 50x100 $\mathrm{cm}^2$) and thanks to the small thickness of these foils is it possible to shape it to the desired form: a Cylindrical Gas Electron Multiplier (CGEM) is then proposed. The innovative construction technique based on Rohacell, a PMI foam, will give solidity to cathode and anode with a very low impact on material budget. The entire detector is sustained by Permaglass rings glued at the edges. These rings are used to assembly the CGEM, together with a dedicated Vertical Insertion System and moreover they host the On-Detector electronic. The anode has been improved w.r.t. the state of the art through a jagged readout that minimize the inter-strip capacitance. The mechanical challenge of this detector requires a precision of the entire geometry within few hundreds of microns in the whole area. In this contribution an overview of the construction technique, the validation of this technique through the realization of a CGEM, and its first tests will be presented. These activities are performed within the framework of the BESIIICGEM Project (645664), funded by the European Commission in the action H2020-RISE-MSCA-2014.
△ Less
Submitted 20 March, 2018;
originally announced March 2018.
-
Performance of the micro-TPC Reconstruction for GEM Detectors at High Rate
Authors:
L. Lavezzi,
M. Alexeev,
A. Amoroso,
R. Baldini Ferroli,
M. Bertani,
D. Bettoni,
F. Bianchi,
A. Calcaterra,
N. Canale,
M. Capodiferro,
V. Carassiti,
S. Cerioni,
JY. Chai,
S. Chiozzi,
G. Cibinetto,
F. Cossio,
A. Cotta Ramusino,
F. De Mori,
M. Destefanis,
J. Dong,
F. Evangelisti,
R. Farinelli,
L. Fava,
G. Felici,
E. Fioravanti
, et al. (27 additional authors not shown)
Abstract:
Gas detectors are one of the pillars of the research in fundamental physics. Since many years, a new concept of detectors, the Micro Pattern Gas Detectors, allows to overcome many of the problems of other types of commonly used detectors, as drift chambers and microstrips, reducing the discharge rate and increasing the radiation tolerance. Among these, one of the most commonly used is the Gas Elec…
▽ More
Gas detectors are one of the pillars of the research in fundamental physics. Since many years, a new concept of detectors, the Micro Pattern Gas Detectors, allows to overcome many of the problems of other types of commonly used detectors, as drift chambers and microstrips, reducing the discharge rate and increasing the radiation tolerance. Among these, one of the most commonly used is the Gas Electron Multiplier. Commonly deployed as fast timing detectors and triggers, due to their fast response, high rate capability and high radiation hardness, they can also be used as trackers. The center of gravity readout technique allows to overcome the limit of the digital pads, whose spatial resolution is constrained by the pitch size. The presence of a high external magnetic field can distort the electronic cloud and affect the spatial resolution. The micro-TPC reconstruction method allows to reconstruct the three dimensional particle position as in a traditional Time Projection Chamber, but within a drift gap of a few millimeters. This method brings these detectors into a new perspective for what concerns the spatial resolution in strong magnetic field. In this report, the basis of this new technique will be shown and it will be compared to the traditional center of gravity. The results of a series of test beam performed with 10 x 10 cm2 planar prototypes in magnetic field will also be presented. This is one of the first implementations of this technique for GEM detectors in magnetic field and allows to reach unprecedented performance for gas detectors, up to a limit of 120 micron at 1T, one of the world's best results for MPGDs in strong magnetic field. The micro-TPC reconstruction has been recently tested at very high rates in a test beam at the MAMI facility; preliminary results of the test will be presented.
△ Less
Submitted 20 March, 2018;
originally announced March 2018.
-
Test beam results with prototypes for the new Cylindrical GEM Inner Tracker of the BESIII experiment
Authors:
L. Lavezzi,
M. Alexeev,
A. Amoroso,
R. Baldini Ferroli,
M. Bertani,
D. Bettoni,
F. Bianchi,
A. Calcaterra,
N. Canale,
M. Capodiferro,
V. Carassiti,
S. Cerioni,
JY. Chai,
S. Chiozzi,
G. Cibinetto,
F. Cossio,
A. Cotta Ramusino,
F. De Mori,
M. Destefanis,
J. Dong,
F. Evangelisti,
R. Farinelli,
L. Fava,
G. Felici,
E. Fioravanti
, et al. (27 additional authors not shown)
Abstract:
A cylindrical GEM tracker is under construction in order to replace and improve the inner tracking system of the BESIII experiment. Tests with planar chamber prototypes were carried out on the H4 beam line of SPS (CERN) with muons of 150 GeV/c momentum, to evaluate the efficiency and resolution under different working conditions. The obtained efficiency was in the 96 - 98% range. Two complementary…
▽ More
A cylindrical GEM tracker is under construction in order to replace and improve the inner tracking system of the BESIII experiment. Tests with planar chamber prototypes were carried out on the H4 beam line of SPS (CERN) with muons of 150 GeV/c momentum, to evaluate the efficiency and resolution under different working conditions. The obtained efficiency was in the 96 - 98% range. Two complementary algorithms for the position determination were developed: the charge centroid and the micro-TPC methods. With the former, resolutions <100 micron and <200 micron were achieved without and with magnetic field, respectively. The micro-TPC improved these results. By the end of 2016, the first cylindrical prototype was tested on the same beam line. It showed optimal stability under different settings. The comparison of its performance with respect to the planar chambers is ongoing. Here, the results of the planar prototype tests will be addressed.
△ Less
Submitted 20 March, 2018;
originally announced March 2018.
-
The new cylindrical GEM inner tracker of BESIII
Authors:
L. Lavezzi,
M. Alexeev,
A. Amoroso,
R. Baldini Ferroli,
M. Bertani,
D. Bettoni,
F. Bianchi,
A. Calcaterra,
N. Canale,
M. Capodiferro,
V. Carassiti,
S. Cerioni,
JY. Chai,
S. Chiozzi,
G. Cibinetto,
F. Cossio,
A. Cotta Ramusino,
F. De Mori,
M. Destefanis,
J. Dong,
F. Evangelisti,
R. Farinelli,
L. Fava,
G. Felici,
E. Fioravanti
, et al. (27 additional authors not shown)
Abstract:
The Cylindrical GEM-Inner Tracker (CGEM-IT) is the upgrade of the internal tracking system of the BESIII experiment. It consists of three layers of cylindrically-shaped triple GEMs, with important innovations with respect to the existing GEM detectors, in order to achieve the best performance with the lowest material budget. It will be the first cylindrical GEM running with analog readout inside a…
▽ More
The Cylindrical GEM-Inner Tracker (CGEM-IT) is the upgrade of the internal tracking system of the BESIII experiment. It consists of three layers of cylindrically-shaped triple GEMs, with important innovations with respect to the existing GEM detectors, in order to achieve the best performance with the lowest material budget. It will be the first cylindrical GEM running with analog readout inside a 1T magnetic field. The simultaneous measurement of both the deposited charge and the signal time will permit to use a combination of two algorithms to evaluate the spatial position of the charged tracks inside the CGEM-IT: the charge centroid and the micro time projection chamber modes. They are complementary and can cope with the asymmetry of the electron avalanche when running in magnetic field and with non-orthogonal incident tracks. To evaluate the behavior under different working settings, both planar chambers and the first cylindrical prototype have been tested during various test beams at CERN with 150 GeV/c muons and pions. This paper reports the results obtained with the two reconstruction methods and a comparison between the planar and cylindrical chambers.
△ Less
Submitted 20 March, 2018;
originally announced March 2018.
-
The integration and testing of the Mini-EUSO multi-level trigger system
Authors:
A. Belov,
M. Bertaina,
F. Capel,
F. Faust,
F. Fenu,
P. Klimov,
M. Mignone,
H. Miyamoto
Abstract:
The Mini-EUSO telescope is designed by the JEM-EUSO Collaboration to observe the UV emission of the Earth from the vantage point of the International Space Station (ISS) in low Earth orbit. The main goal of the mission is to map the Earth in the UV, thus increasing the technological readiness level of future EUSO experiments and to lay the groundwork for the detection of Extreme Energy Cosmic Rays…
▽ More
The Mini-EUSO telescope is designed by the JEM-EUSO Collaboration to observe the UV emission of the Earth from the vantage point of the International Space Station (ISS) in low Earth orbit. The main goal of the mission is to map the Earth in the UV, thus increasing the technological readiness level of future EUSO experiments and to lay the groundwork for the detection of Extreme Energy Cosmic Rays (EECRs) from space. Due to its high time resolution of 2.5 us, Mini-EUSO is capable of detecting a wide range of UV phenomena in the Earth's atmosphere. In order to maximise the scientific return of the mission, it is necessary to implement a multi-level trigger logic for data selection over different timescales. This logic is key to the success of the mission and thus must be thoroughly tested and carefully integrated into the data processing system prior to the launch. This article introduces the motivation behind the trigger design and details the integration and testing of the logic.
△ Less
Submitted 7 November, 2017;
originally announced November 2017.
-
The Cylindrical GEM Inner Tracker of the BESIII experiment: prototype test beam results
Authors:
L. Lavezzi,
M. Alexeev,
A. Amoroso,
R. Baldini Ferroli,
M. Bertani,
D. Bettoni,
F. Bianchi,
A. Calcaterra,
N. Canale,
M. Capodiferro,
V. Carassiti,
S. Cerioni,
JY. Chai,
S. Chiozzi,
G. Cibinetto,
F. Cossio,
A. Cotta Ramusino,
F. De Mori,
M. Destefanis,
J. Dong,
F. Evangelisti,
R. Farinelli,
L. Fava,
G. Felici,
E. Fioravanti
, et al. (27 additional authors not shown)
Abstract:
A cylindrical GEM detector is under development, to serve as an upgraded inner tracker at the BESIII spectrometer. It will consist of three layers of cylindrically-shaped triple GEMs surrounding the interaction point. The experiment is taking data at the e+e- collider BEPCII in Bei**g (China) and the GEM tracker will be installed in 2018. Tests on the performances of triple GEMs in strong magneti…
▽ More
A cylindrical GEM detector is under development, to serve as an upgraded inner tracker at the BESIII spectrometer. It will consist of three layers of cylindrically-shaped triple GEMs surrounding the interaction point. The experiment is taking data at the e+e- collider BEPCII in Bei**g (China) and the GEM tracker will be installed in 2018. Tests on the performances of triple GEMs in strong magnetic field have been run by means of the muon beam available in the H4 line of SPS (CERN) with both planar chambers and the first cylindrical prototype. Efficiencies and resolutions have been evaluated using different gains, gas mixtures, with and without magnetic field. The obtained efficiency is 97-98% on single coordinate view, in many operational arrangements. The spatial resolution for planar GEMs has been evaluated with two different algorithms for the position determination: the charge centroid and the micro time projection chamber (mu-TPC) methods. The two modes are complementary and are able to cope with the asymmetry of the electron avalanche when running in magnetic field, and with non-orthogonal incident tracks. With the charge centroid, a resolution lower than 100 micron has been reached without magnetic field and lower than 200 micron with a magnetic field up to 1 T. The mu-TPC mode showed to be able to improve those results. In the first beam test with the cylindrical prototype, the detector had a very good stability under different voltage configurations and particle intensities. The resolution evaluation is in progress.
△ Less
Submitted 3 July, 2017; v1 submitted 7 June, 2017;
originally announced June 2017.
-
A custom readout electronics for the BESIII CGEM detector
Authors:
M. Da Rocha Rolo,
M. Alexeev,
A. Amoroso,
R. Baldini Ferroli,
M. Bertani,
D. Bettoni,
F. Bianchi,
R. Bugalho,
A. Calcaterra,
N. Canale,
M. Capodiferro,
V. Carassiti,
S. Cerioni,
JY. Chai,
S. Chiozzi,
G. Cibinetto,
F. Cossio,
A. Cotta Ramusino,
F. De Mori,
M. Destefanis,
A. Di Francesco,
J. Dong,
F. Evangelisti,
R. Farinelli,
L. Fava
, et al. (31 additional authors not shown)
Abstract:
For the upgrade of the inner tracker of the BESIII spectrometer, planned for 2018, a lightweight tracker based on an innovative Cylindrical Gas Electron Multiplier (CGEM) detector is now under development. The analogue readout of the CGEM enables the use of a charge centroid algorithm to improve the spatial resolution to better than 130 um while loosening the pitch strip to 650 um, which allows to…
▽ More
For the upgrade of the inner tracker of the BESIII spectrometer, planned for 2018, a lightweight tracker based on an innovative Cylindrical Gas Electron Multiplier (CGEM) detector is now under development. The analogue readout of the CGEM enables the use of a charge centroid algorithm to improve the spatial resolution to better than 130 um while loosening the pitch strip to 650 um, which allows to reduce the total number of channels to about 10 000. The channels are readout by 160 dedicated integrated 64-channel front-end ASICs, providing a time and charge measurement and featuring a fully-digital output. The energy measurement is extracted either from the time-over-threshold (ToT) or the 10-bit digitisation of the peak amplitude of the signal. The time of the event is generated by quad-buffered low-power TDCs, allowing for rates in excess of 60 kHz per channel. The TDCs are based on analogue interpolation techniques and produce a time stamp (or two, if working in ToT mode) of the event with a time resolution better than 50 ps. The front-end noise, based on a CSA and CR-RC2 shapers, dominate the channel intrinsic time jitter, which is less than 5 ns r.m.s.. The time information of the hit can be used to reconstruct the track path, operating the detector as a small TPC and hence improving the position resolution when the distribution of the cloud, due to large incident angle or magnetic field, is very broad. Event data is collected by an off-detector motherboard, where each GEM-ROC readout card handles 4 ASIC carrier PCBs (512 channels). Configuration upload and data readout between the off-detector electronics and the VME-based data collector cards are managed by bi-directional fibre optical links.
△ Less
Submitted 28 June, 2017; v1 submitted 7 June, 2017;
originally announced June 2017.
-
The EUSO@TurLab Project
Authors:
H. Miyamoto,
M. Bertaina,
G. Cotto,
R. Forza,
M. Manfrin,
M. Mignone,
G. Suino,
A. Youssef,
R. Caruso,
G. Contino,
S. Bacholle,
P. Gorodetzky,
A. Jung,
E. Parizot,
G. Prevôt,
P. Barrillon,
S. Dagoret-Campagne,
J. Rabanal Reina,
S. Blin
Abstract:
The TurLab facility is a laboratory, equipped with a 5 m diameter and 1 m depth rotating tank, located in the Physics Department of the University of Turin. The tank has been built mainly to study problems where system rotation plays a key role in the fluid behaviour such as in atmospheric and oceanic flows at different scales. The tank can be filled with different fluids of variable density, whic…
▽ More
The TurLab facility is a laboratory, equipped with a 5 m diameter and 1 m depth rotating tank, located in the Physics Department of the University of Turin. The tank has been built mainly to study problems where system rotation plays a key role in the fluid behaviour such as in atmospheric and oceanic flows at different scales. The tank can be filled with different fluids of variable density, which enables studies in layered conditions such as sea waves. The tank can be also used to simulate the terrestrial surface with the optical characteristics of different environments such as snow, grass, ocean, land with soil, stones etc., fogs and clouds. As it is located in an extremely dark place, the light intensity can be controlled artificially. Such capabilities of the TurLab facility are applied to perform experiments related to the observation of Extreme Energy Cosmic Rays (EECRs) from space using the fluorescence technique, as in the case of the JEM-EUSO mission, where the diffuse night brightness and artificial light sources can vary significantly in time and space inside the Field of View (FoV) of the telescope. Here we will report the currently ongoing activity at the TurLab facility in the framework of the JEM-EUSO mission (EUSO@TurLab).
△ Less
Submitted 26 January, 2017;
originally announced January 2017.
-
Feasibility study for the measurement of $πN$ TDAs at PANDA in $\bar{p}p\to J/ψπ^0$
Authors:
PANDA Collaboration,
B. Singh,
W. Erni,
B. Krusche,
M. Steinacher,
N. Walford,
H. Liu,
Z. Liu,
B. Liu,
X. Shen,
C. Wang,
J. Zhao,
M. Albrecht,
T. Erlen,
M. Fink,
F. H. Heinsius,
T. Held,
T. Holtmann,
S. Jasper,
I. Keshk,
H. Koch,
B. Kopf,
M. Kuhlmann,
M. Kümmel,
S. Leiber
, et al. (488 additional authors not shown)
Abstract:
The exclusive charmonium production process in $\bar{p}p$ annihilation with an associated $π^0$ meson $\bar{p}p\to J/ψπ^0$ is studied in the framework of QCD collinear factorization. The feasibility of measuring this reaction through the $J/ψ\to e^+e^-$ decay channel with the PANDA (AntiProton ANnihilation at DArmstadt) experiment is investigated. Simulations on signal reconstruction efficiency as…
▽ More
The exclusive charmonium production process in $\bar{p}p$ annihilation with an associated $π^0$ meson $\bar{p}p\to J/ψπ^0$ is studied in the framework of QCD collinear factorization. The feasibility of measuring this reaction through the $J/ψ\to e^+e^-$ decay channel with the PANDA (AntiProton ANnihilation at DArmstadt) experiment is investigated. Simulations on signal reconstruction efficiency as well as the background rejection from various sources including the $\bar{p}p\toπ^+π^-π^0$ and $\bar{p}p\to J/ψπ^0π^0$ reactions are performed with PandaRoot, the simulation and analysis software framework of the PANDA experiment. It is shown that the measurement can be done at PANDA with significant constraining power under the assumption of an integrated luminosity attainable in four to five months of data taking at the maximum design luminosity.
△ Less
Submitted 7 October, 2016;
originally announced October 2016.
-
Feasibility studies of time-like proton electromagnetic form factors at PANDA at FAIR
Authors:
PANDA Collaboration,
B. Singh,
W. Erni,
B. Krusche,
M. Steinacher,
N. Walford,
B. Liu,
H. Liu,
Z. Liu,
X. Shen,
C. Wang,
J. Zhao,
M. Albrecht,
T. Erlen,
M. Fink,
F. Heinsius,
T. Held,
T. Holtmann,
S. Jasper,
I. Keshk,
H. Koch,
B. Kopf,
M. Kuhlmann,
M. Kümmel,
S. Leiber
, et al. (482 additional authors not shown)
Abstract:
Simulation results for future measurements of electromagnetic proton form factors at \PANDA (FAIR) within the PandaRoot software framework are reported. The statistical precision with which the proton form factors can be determined is estimated. The signal channel $\bar p p \to e^+ e^-$ is studied on the basis of two different but consistent procedures. The suppression of the main background chann…
▽ More
Simulation results for future measurements of electromagnetic proton form factors at \PANDA (FAIR) within the PandaRoot software framework are reported. The statistical precision with which the proton form factors can be determined is estimated. The signal channel $\bar p p \to e^+ e^-$ is studied on the basis of two different but consistent procedures. The suppression of the main background channel, $\textit{i.e.}$ $\bar p p \to π^+ π^-$, is studied. Furthermore, the background versus signal efficiency, statistical and systematical uncertainties on the extracted proton form factors are evaluated using two different procedures. The results are consistent with those of a previous simulation study using an older, simplified framework. However, a slightly better precision is achieved in the PandaRoot study in a large range of momentum transfer, assuming the nominal beam conditions and detector performance.
△ Less
Submitted 29 September, 2016; v1 submitted 3 June, 2016;
originally announced June 2016.
-
Technical Design Report for the: PANDA Micro Vertex Detector
Authors:
PANDA Collaboration,
W. Erni,
I. Keshelashvili,
B. Krusche,
M. Steinacher,
Y. Heng,
Z. Liu,
H. Liu,
X. Shen,
Q. Wang,
H. Xu,
M. Albrecht,
J. Becker,
K. Eickel,
F. Feldbauer,
M. Fink,
P. Friedel,
F. H. Heinsius,
T. Held,
H. Koch,
B. Kopf,
M. Leyhe,
C. Motzko,
M. Pelizäus,
J. Pychy
, et al. (436 additional authors not shown)
Abstract:
This document illustrates the technical layout and the expected performance of the Micro Vertex Detector (MVD) of the PANDA experiment. The MVD will detect charged particles as close as possible to the interaction zone. Design criteria and the optimisation process as well as the technical solutions chosen are discussed and the results of this process are subjected to extensive Monte Carlo physics…
▽ More
This document illustrates the technical layout and the expected performance of the Micro Vertex Detector (MVD) of the PANDA experiment. The MVD will detect charged particles as close as possible to the interaction zone. Design criteria and the optimisation process as well as the technical solutions chosen are discussed and the results of this process are subjected to extensive Monte Carlo physics studies. The route towards realisation of the detector is outlined.
△ Less
Submitted 10 August, 2012; v1 submitted 27 July, 2012;
originally announced July 2012.
