-
Characterisation of spatial charge sensitivity in a multi-mode superconducting qubit
Authors:
J. Wills,
G. Campanaro,
S. Cao,
S. D. Fasciati,
P. J. Leek,
B. Vlastakis
Abstract:
Understanding and suppressing sources of decoherence is a leading challenge in building practical quantum computers. In superconducting qubits, low frequency charge noise is a well-known decoherence mechanism that is effectively suppressed in the transmon qubit. Devices with multiple charge-sensitive modes can exhibit more complex behaviours, which can be exploited to study charge fluctuations in…
▽ More
Understanding and suppressing sources of decoherence is a leading challenge in building practical quantum computers. In superconducting qubits, low frequency charge noise is a well-known decoherence mechanism that is effectively suppressed in the transmon qubit. Devices with multiple charge-sensitive modes can exhibit more complex behaviours, which can be exploited to study charge fluctuations in superconducting qubits. Here we characterise charge-sensitivity in a superconducting qubit with two transmon-like modes, each of which is sensitive to multiple charge-parity configurations and charge-offset biases. Using Ramsey interferometry, we observe sensitivity to four charge-parity configurations and track two independent charge-offset drifts over hour timescales. We provide a predictive theory for charge sensitivity in such multi-mode qubits which agrees with our results. Finally, we demonstrate the utility of a multi-mode qubit as a charge detector by spatially tracking local-charge drift.
△ Less
Submitted 4 August, 2021;
originally announced August 2021.
-
High Coherence in a Tileable 3D Integrated Superconducting Circuit Architecture
Authors:
Peter A. Spring,
Shuxiang Cao,
Takahiro Tsunoda,
Giulio Campanaro,
Simone D. Fasciati,
James Wills,
Vivek Chidambaram,
Boris Shteynas,
Mustafa Bakr,
Paul Gow,
Lewis Carpenter,
James Gates,
Brian Vlastakis,
Peter J. Leek
Abstract:
We report high qubit coherence as well as low crosstalk and single-qubit gate errors in a superconducting circuit architecture that promises to be tileable to 2D lattices of qubits. The architecture integrates an inductively shunted cavity enclosure into a design featuring non-galvanic out-of-plane control wiring and qubits and resonators fabricated on opposing sides of a substrate. The proof-of-p…
▽ More
We report high qubit coherence as well as low crosstalk and single-qubit gate errors in a superconducting circuit architecture that promises to be tileable to 2D lattices of qubits. The architecture integrates an inductively shunted cavity enclosure into a design featuring non-galvanic out-of-plane control wiring and qubits and resonators fabricated on opposing sides of a substrate. The proof-of-principle device features four uncoupled transmon qubits and exhibits average energy relaxation times $T_1=149(38)~μ$s, pure echoed dephasing times $T_{φ,e}=189(34)~μ$s, and single-qubit gate fidelities $F=99.982(4)\%$ as measured by simultaneous randomized benchmarking. The 3D integrated nature of the control wiring means that qubits will remain addressable as the architecture is tiled to form larger qubit lattices. Band structure simulations are used to predict that the tiled enclosure will still provide a clean electromagnetic environment to enclosed qubits at arbitrary scale.
△ Less
Submitted 23 July, 2021;
originally announced July 2021.
-
Radio-frequency characterization of a supercurrent transistor made from a carbon nanotube
Authors:
M. Mergenthaler,
F. J. Schupp,
A. Nersisyan,
N. Ares,
A. Baumgartner,
C. Schönenberger,
G. A. D. Briggs,
P. J. Leek,
E. A. Laird
Abstract:
A supercurrent transistor is a superconductor-semiconductor hybrid device in which the Josephson supercurrent is switched on and off using a gate voltage. While such devices have been studied using DC transport, radio-frequency measurements allow for more sensitive and faster experiments. Here a supercurrent transistor made from a carbon nanotube is measured simultaneously via DC conductance and r…
▽ More
A supercurrent transistor is a superconductor-semiconductor hybrid device in which the Josephson supercurrent is switched on and off using a gate voltage. While such devices have been studied using DC transport, radio-frequency measurements allow for more sensitive and faster experiments. Here a supercurrent transistor made from a carbon nanotube is measured simultaneously via DC conductance and radio-frequency reflectometry. The radio-frequency measurement resolves all the main features of the conductance data across a wide range of bias and gate voltage, and many of these features are seen more clearly. These results are promising for measuring other kinds of hybrid superconducting devices, in particular for detecting the reactive component of the impedance, which a DC measurement can never detect.
△ Less
Submitted 30 March, 2021;
originally announced March 2021.
-
Efficient Hamiltonian programming in qubit arrays with nearest-neighbour couplings
Authors:
Takahiro Tsunoda,
Gaurav Bhole,
Stephen A. Jones,
Jonathan A. Jones,
Peter J. Leek
Abstract:
We consider the problem of selectively controlling couplings in a practical quantum processor with always-on interactions that are diagonal in the computational basis, using sequences of local NOT gates. This methodology is well-known in NMR implementations, but previous approaches do not scale efficiently for the general fully-connected Hamiltonian, where the complexity of finding time-optimal so…
▽ More
We consider the problem of selectively controlling couplings in a practical quantum processor with always-on interactions that are diagonal in the computational basis, using sequences of local NOT gates. This methodology is well-known in NMR implementations, but previous approaches do not scale efficiently for the general fully-connected Hamiltonian, where the complexity of finding time-optimal solutions makes them only practical up to a few tens of qubits. Given the rapid growth in the number of qubits in cutting-edge quantum processors, it is of interest to investigate the applicability of this control scheme to much larger scale systems with realistic restrictions on connectivity. Here we present an efficient scheme to find near time-optimal solutions that can be applied to engineered qubit arrays with local connectivity for any number of qubits, indicating the potential for practical quantum computing in such systems.
△ Less
Submitted 5 May, 2020; v1 submitted 17 March, 2020;
originally announced March 2020.
-
Rescaling interactions for quantum control
Authors:
Gaurav Bhole,
Takahiro Tsunoda,
Peter J. Leek,
Jonathan A. Jones
Abstract:
A powerful control method in experimental quantum computing is the use of spin echoes, employed to select a desired term in the system's internal Hamiltonian, while refocusing others. Here we address a more general problem, describing a method to not only turn on and off particular interactions but also to rescale their strengths so that we can generate any desired effective internal Hamiltonian.…
▽ More
A powerful control method in experimental quantum computing is the use of spin echoes, employed to select a desired term in the system's internal Hamiltonian, while refocusing others. Here we address a more general problem, describing a method to not only turn on and off particular interactions but also to rescale their strengths so that we can generate any desired effective internal Hamiltonian. We propose an algorithm based on linear programming for achieving time-optimal rescaling solutions in fully coupled systems of tens of qubits, which can be modified to obtain near time-optimal solutions for rescaling systems with hundreds of qubits.
△ Less
Submitted 13 January, 2020; v1 submitted 12 November, 2019;
originally announced November 2019.
-
Modelling Enclosures for Large-Scale Superconducting Quantum Circuits
Authors:
P. A. Spring,
T. Tsunoda,
B. Vlastakis,
P. J. Leek
Abstract:
Superconducting quantum circuits are typically housed in conducting enclosures in order to control their electromagnetic environment. As devices grow in physical size, the electromagnetic modes of the enclosure come down in frequency and can introduce unwanted long-range cross-talk between distant elements of the enclosed circuit. Incorporating arrays of inductive shunts such as through-substrate…
▽ More
Superconducting quantum circuits are typically housed in conducting enclosures in order to control their electromagnetic environment. As devices grow in physical size, the electromagnetic modes of the enclosure come down in frequency and can introduce unwanted long-range cross-talk between distant elements of the enclosed circuit. Incorporating arrays of inductive shunts such as through-substrate vias or machined pillars can suppress these effects by raising these mode frequencies. Here, we derive simple, accurate models for the modes of enclosures that incorporate such inductive-shunt arrays. We use these models to predict that cavity-mediated inter-qubit couplings and drive-line cross-talk are exponentially suppressed with distance for arbitrarily large quantum circuits housed in such enclosures, indicating the promise of this approach for quantum computing. We find good agreement with a finite-element simulation of an example device containing more than 400 qubits.
△ Less
Submitted 2 June, 2020; v1 submitted 4 September, 2019;
originally announced September 2019.
-
Critical slowing down in the bistable regime of circuit quantum electrodynamics
Authors:
P. Brookes,
G. Tancredi,
A. D. Patterson,
J. Rahamim,
M. Esposito,
P. J. Leek,
E. Ginossar,
M. H. Szymanska
Abstract:
We investigate the dynamics of the bistable regime of the generalized Jaynes-Cummings Hamiltonian (GJC), realised by a circuit quantum electrodynamics (cQED) system consisting of a transmon qubit coupled to a microwave cavity. In this regime we observe critical slowing down in the approach to the steady state. By measuring the response of the cavity to a step function drive pulse we characterize t…
▽ More
We investigate the dynamics of the bistable regime of the generalized Jaynes-Cummings Hamiltonian (GJC), realised by a circuit quantum electrodynamics (cQED) system consisting of a transmon qubit coupled to a microwave cavity. In this regime we observe critical slowing down in the approach to the steady state. By measuring the response of the cavity to a step function drive pulse we characterize this slowing down as a function of driving frequency and power. We find that the critical slowing down saturates as the driving power is increased. We compare these results with the predictions of analytical and numerical calculations both with and without the Duffing approximation. We find that the Duffing approximation incorrectly predicts that the critical slowing down timescale increases exponentially with the drive, whereas the GJC model accurately predicts the saturation seen in our data, suggesting a different process of quantum activation.
△ Less
Submitted 31 July, 2019;
originally announced July 2019.
-
Calibration of the cross-resonance two-qubit gate between directly-coupled transmons
Authors:
A. D. Patterson,
J. Rahamim,
T. Tsunoda,
P. Spring,
S. Jebari,
K. Ratter,
M. Mergenthaler,
G. Tancredi,
B. Vlastakis,
M. Esposito,
P. J. Leek
Abstract:
Quantum computation requires the precise control of the evolution of a quantum system, typically through application of discrete quantum logic gates on a set of qubits. Here, we use the cross-resonance interaction to implement a gate between two superconducting transmon qubits with a direct static dispersive coupling. We demonstrate a practical calibration procedure for the optimization of the gat…
▽ More
Quantum computation requires the precise control of the evolution of a quantum system, typically through application of discrete quantum logic gates on a set of qubits. Here, we use the cross-resonance interaction to implement a gate between two superconducting transmon qubits with a direct static dispersive coupling. We demonstrate a practical calibration procedure for the optimization of the gate, combining continuous and repeated-gate Hamiltonian tomography with step-wise reduction of dominant two-qubit coherent errors through map** to microwave control parameters. We show experimentally that this procedure can enable a $\hat{ZX}_{-π/2}$ gate with a fidelity $F=97.0(7)\%$, measured with interleaved randomized benchmarking. We show this in a architecture with out-of-plane control and readout that is readily extensible to larger scale quantum circuits.
△ Less
Submitted 14 May, 2019;
originally announced May 2019.
-
Realization of a Carbon-Nanotube-Based Superconducting Qubit
Authors:
Matthias Mergenthaler,
Ani Nersisyan,
Andrew Patterson,
Martina Esposito,
Andreas Baumgartner,
Christian Schönenberger,
G. Andrew D. Briggs,
Edward A. Laird,
Peter J. Leek
Abstract:
Hybrid circuit quantum electrodynamics (QED) involves the study of coherent quantum physics in solid state systems via their interactions with superconducting microwave circuits. Here we present an implementation of a hybrid superconducting qubit that employs a carbon nanotube as a Josephson junction. We realize the junction by contacting a carbon nanotube with a superconducting Pd/Al bi-layer, an…
▽ More
Hybrid circuit quantum electrodynamics (QED) involves the study of coherent quantum physics in solid state systems via their interactions with superconducting microwave circuits. Here we present an implementation of a hybrid superconducting qubit that employs a carbon nanotube as a Josephson junction. We realize the junction by contacting a carbon nanotube with a superconducting Pd/Al bi-layer, and implement voltage tunability of the qubit frequency using a local electrostatic gate. We demonstrate strong dispersive coupling to a coplanar waveguide resonator via observation of a resonator frequency shift dependent on applied gate voltage. We extract qubit parameters from spectroscopy using dispersive readout and find qubit relaxation and coherence times in the range of $10-200~\rm{ns}$.
△ Less
Submitted 22 April, 2019;
originally announced April 2019.
-
Strong coupling of microwave photons to antiferromagnetic fluctuations in an organic magnet
Authors:
M. Mergenthaler,
J. Liu,
J. J. Le Roy,
N. Ares,
A. L. Thompson,
L. Bogani,
F. Luis,
S. J. Blundell,
T. Lancaster,
A. Ardavan,
G. A. D. Briggs,
P. J. Leek,
E. A. Laird
Abstract:
Coupling between a crystal of di(phenyl)-(2,4,6-trinitrophenyl)iminoazanium radicals and a superconducting microwave resonator is investigated in a circuit quantum electrodynamics (circuit QED) architecture. The crystal exhibits paramagnetic behavior above 4~K, with antiferromagnetic correlations appearing below this temperature, and we demonstrate strong coupling at base temperature. The magnetic…
▽ More
Coupling between a crystal of di(phenyl)-(2,4,6-trinitrophenyl)iminoazanium radicals and a superconducting microwave resonator is investigated in a circuit quantum electrodynamics (circuit QED) architecture. The crystal exhibits paramagnetic behavior above 4~K, with antiferromagnetic correlations appearing below this temperature, and we demonstrate strong coupling at base temperature. The magnetic resonance acquires a field angle dependence as the crystal is cooled down, indicating anisotropy of the exchange interactions. These results show that multispin modes in organic crystals are suitable for circuit QED, offering a platform for their coherent manipulation. They also utilize the circuit QED architecture as a way to probe spin correlations at low temperature.
△ Less
Submitted 9 October, 2017; v1 submitted 17 March, 2017;
originally announced March 2017.
-
Double-sided coaxial circuit QED with out-of-plane wiring
Authors:
J. Rahamim,
T. Behrle,
M. J. Peterer,
A. Patterson,
P. Spring,
T. Tsunoda,
R. Manenti,
G. Tancredi,
P. J. Leek
Abstract:
Superconducting circuits are well established as a strong candidate platform for the development of quantum computing. In order to advance to a practically useful level, architectures are needed which combine arrays of many qubits with selective qubit control and readout, without compromising on coherence. Here we present a coaxial circuit QED architecture in which qubit and resonator are fabricat…
▽ More
Superconducting circuits are well established as a strong candidate platform for the development of quantum computing. In order to advance to a practically useful level, architectures are needed which combine arrays of many qubits with selective qubit control and readout, without compromising on coherence. Here we present a coaxial circuit QED architecture in which qubit and resonator are fabricated on opposing sides of a single chip, and control and readout wiring are provided by coaxial wiring running perpendicular to the chip plane. We present characterisation measurements of a fabricated device in good agreement with simulated parameters and demonstrating energy relaxation and dephasing times of $T_1 = 4.1\,μ$s and $T_2 = 5.7\,μ$s respectively. The architecture allows for scaling to large arrays of selectively controlled and measured qubits with the advantage of all wiring being out of the plane.
△ Less
Submitted 1 June, 2017; v1 submitted 16 March, 2017;
originally announced March 2017.
-
Circuit quantum acoustodynamics with surface acoustic waves
Authors:
R. Manenti,
A. F. Kockum,
A. Patterson,
T. Behrle,
J. Rahamim,
G. Tancredi,
F. Nori,
P. J. Leek
Abstract:
The experimental investigation of quantum devices incorporating mechanical resonators has opened up new frontiers in the study of quantum mechanics at a macroscopic level$^{1,2}$. Superconducting microwave circuits have proven to be a powerful platform for the realisation of such quantum devices, both in cavity optomechanics$^{3,4}$, and circuit quantum electro-dynamics (QED)$^{5,6}$. While most e…
▽ More
The experimental investigation of quantum devices incorporating mechanical resonators has opened up new frontiers in the study of quantum mechanics at a macroscopic level$^{1,2}$. Superconducting microwave circuits have proven to be a powerful platform for the realisation of such quantum devices, both in cavity optomechanics$^{3,4}$, and circuit quantum electro-dynamics (QED)$^{5,6}$. While most experiments to date have involved localised nanomechanical resonators, it has recently been shown that propagating surface acoustic waves (SAWs) can be piezoelectrically coupled to superconducting qubits$^{7,8}$, and confined in high-quality Fabry-Perot cavities up to microwave frequencies in the quantum regime$^{9}$, indicating the possibility of realising coherent exchange of quantum information between the two systems. Here we present measurements of a device in which a superconducting qubit is embedded in, and interacts with, the acoustic field of a Fabry-Perot SAW cavity on quartz, realising a surface acoustic version of cavity quantum electrodynamics. This quantum acoustodynamics (QAD) architecture may be used to develop new quantum acoustic devices in which quantum information is stored in trapped on-chip surface acoustic wavepackets, and manipulated in ways that are impossible with purely electromagnetic signals, due to the $10^{5}$ times slower speed of travel of the mechanical waves.
△ Less
Submitted 13 March, 2017;
originally announced March 2017.
-
Simultaneous bistability of qubit and resonator in circuit quantum electrodynamics
Authors:
Th. K. Mavrogordatos,
G. Tancredi,
M. Elliott,
M. J. Peterer,
A. Patterson,
J. Rahamim,
P. J. Leek,
E. Ginossar,
M. H. Szymańska
Abstract:
We explore the joint activated dynamics exhibited by two quantum degrees of freedom: a cavity mode oscillator which is strongly coupled to a superconducting qubit in the strongly coherently driven dispersive regime. Dynamical simulations and complementary measurements show a range of parameters where both the cavity and the qubit exhibit sudden simultaneous switching between two metastable states.…
▽ More
We explore the joint activated dynamics exhibited by two quantum degrees of freedom: a cavity mode oscillator which is strongly coupled to a superconducting qubit in the strongly coherently driven dispersive regime. Dynamical simulations and complementary measurements show a range of parameters where both the cavity and the qubit exhibit sudden simultaneous switching between two metastable states. This manifests in ensemble averaged amplitudes of both the cavity and qubit exhibiting a partial coherent cancellation. Transmission measurements of driven microwave cavities coupled to transmon qubits show detailed features which agree with the theory in the regime of simultaneous switching.
△ Less
Submitted 2 January, 2017; v1 submitted 30 November, 2016;
originally announced November 2016.
-
Surface acoustic wave resonators in the quantum regime
Authors:
R. Manenti,
M. J. Peterer,
A. Nersisyan,
E. B. Magnusson,
A. Patterson,
P. J. Leek
Abstract:
We present systematic measurements of the quality factors of surface acoustic wave (SAW) resonators on ST-X quartz in the gigahertz range at a temperature of $10 \, \textrm{mK}$. We demonstrate a internal quality factor $Q_\mathrm{i}$ approaching $0.5$ million at $0.5 \, \textrm{GHz}$ and show that $Q_\mathrm{i}\geq4.0\times10^4$ is achievable up to $4.4 \, \textrm{GHz}$. We show evidence for a po…
▽ More
We present systematic measurements of the quality factors of surface acoustic wave (SAW) resonators on ST-X quartz in the gigahertz range at a temperature of $10 \, \textrm{mK}$. We demonstrate a internal quality factor $Q_\mathrm{i}$ approaching $0.5$ million at $0.5 \, \textrm{GHz}$ and show that $Q_\mathrm{i}\geq4.0\times10^4$ is achievable up to $4.4 \, \textrm{GHz}$. We show evidence for a polynomial dependence of propagation loss on frequency, as well as a weak drive power dependence of $Q_\mathrm{i}$ that saturates at low power, the latter being consistent with coupling to a bath of two-level systems. Our results indicate that SAW resonators are promising devices for integration with superconducting quantum circuits.
△ Less
Submitted 16 October, 2015;
originally announced October 2015.
-
Excitation and detection of propagating spin waves at the single magnon level
Authors:
Alexy D. Karenowska,
Andrew D. Patterson,
Michael J. Peterer,
Einar B. Magnússon,
Peter J. Leek
Abstract:
Ferro- and ferrimagnets play host to small-signal, microwave-frequency magnetic excitations called spin waves, the quanta of which are known as magnons. Over the last decade, the field of spin-wave dynamics has contributed much to our understanding of fundamental magnetism. To date, experiments have focussed overwhelmingly on the study of room-temperature systems within classical limits. Here we d…
▽ More
Ferro- and ferrimagnets play host to small-signal, microwave-frequency magnetic excitations called spin waves, the quanta of which are known as magnons. Over the last decade, the field of spin-wave dynamics has contributed much to our understanding of fundamental magnetism. To date, experiments have focussed overwhelmingly on the study of room-temperature systems within classical limits. Here we demonstrate, for the first time, the excitation and detection of propagating spin waves at the single magnon level. Our results allow us to project that coupling of propagating spin-wave excitations to quantum circuits is achievable, enabling fundamental quantum-level studies of magnon systems and potentially opening doors to novel hybrid quantum measurement and information processing devices.
△ Less
Submitted 22 February, 2015;
originally announced February 2015.
-
Surface acoustic wave devices on bulk ZnO at low temperature
Authors:
Einar B. Magnusson,
Benjamin H. Williams,
Riccardo Manenti,
Moon-Sun Nam,
Ani Nersisyan,
Michael J. Peterer,
Arzhang Ardavan,
Peter J. Leek
Abstract:
Surface acoustic wave (SAW) devices based on thin films of ZnO are a well established technology. However, SAW devices on bulk ZnO crystals are not practical at room temperature due to the significant dam** caused by finite electrical conductivity of the crystal. Here, by operating at low temperatures, we demonstrate effective SAW devices on the (0001) surface of bulk ZnO crystals, including a d…
▽ More
Surface acoustic wave (SAW) devices based on thin films of ZnO are a well established technology. However, SAW devices on bulk ZnO crystals are not practical at room temperature due to the significant dam** caused by finite electrical conductivity of the crystal. Here, by operating at low temperatures, we demonstrate effective SAW devices on the (0001) surface of bulk ZnO crystals, including a delay line operating at SAW wavelengths of λ = 4 and 6 μm and a one-port resonator at a wavelength of λ = 1.6 μm. We find that the SAW velocity is temperature dependent, reaching $v \simeq 2.68$ km/s at 10mK. Our resonator reaches a maximum quality factor of $Q_i \simeq 1.5\times 10^5$, demonstrating that bulk ZnO is highly viable for low temperature SAW applications. The performance of the devices is strongly correlated with the bulk conductivity, which quenches SAW transmission above about 200 K.
△ Less
Submitted 24 February, 2015; v1 submitted 21 November, 2014;
originally announced November 2014.
-
Coherence and Decay of Higher Energy Levels of a Superconducting Transmon Qubit
Authors:
Michael J. Peterer,
Samuel J. Bader,
Xiaoyue **,
Fei Yan,
Archana Kamal,
Ted Gudmundsen,
Peter J. Leek,
Terry P. Orlando,
William D. Oliver,
Simon Gustavsson
Abstract:
We present measurements of coherence and successive decay dynamics of higher energy levels of a superconducting transmon qubit. By applying consecutive $π$-pulses for each sequential transition frequency, we excite the qubit from the ground state up to its fourth excited level and characterize the decay and coherence of each state. We find the decay to proceed mainly sequentially, with relaxation…
▽ More
We present measurements of coherence and successive decay dynamics of higher energy levels of a superconducting transmon qubit. By applying consecutive $π$-pulses for each sequential transition frequency, we excite the qubit from the ground state up to its fourth excited level and characterize the decay and coherence of each state. We find the decay to proceed mainly sequentially, with relaxation times in excess of 20 $μ$s for all transitions. We also provide a direct measurement of the charge dispersion of these levels by analyzing beating patterns in Ramsey fringes. The results demonstrate the feasibility of using higher levels in transmon qubits for encoding quantum information.
△ Less
Submitted 12 December, 2014; v1 submitted 21 September, 2014;
originally announced September 2014.
-
Quantum dot admittance probed at microwave frequencies with an on-chip resonator
Authors:
T. Frey,
P. J. Leek,
M. Beck,
J. Faist,
A. Wallraff,
K. Ensslin,
T. Ihn,
M. Büttiker
Abstract:
We present microwave frequency measurements of the dynamic admittance of a quantum dot tunnel coupled to a two-dimensional electron gas. The measurements are made via a high-quality 6.75 GHz on-chip resonator capacitively coupled to the dot. The resonator frequency is found to shift both down and up close to conductance resonance of the dot corresponding to a change of sign of the reactance of the…
▽ More
We present microwave frequency measurements of the dynamic admittance of a quantum dot tunnel coupled to a two-dimensional electron gas. The measurements are made via a high-quality 6.75 GHz on-chip resonator capacitively coupled to the dot. The resonator frequency is found to shift both down and up close to conductance resonance of the dot corresponding to a change of sign of the reactance of the system from capacitive to inductive. The observations are consistent with a scattering matrix model. The sign of the reactance depends on the detuning of the dot from conductance resonance and on the magnitude of the tunnel rate to the lead with respect to the resonator frequency. Inductive response is observed on a conductance resonance, when tunnel coupling and temperature are sufficiently small compared to the resonator frequency.
△ Less
Submitted 3 October, 2012; v1 submitted 4 July, 2012;
originally announced July 2012.
-
Dipole coupling of a double quantum dot to a microwave resonator
Authors:
T. Frey,
P. J. Leek,
M. Beck,
A. Blais,
T. Ihn,
K. Ensslin,
A. Wallraff
Abstract:
Quantum coherence in solid-state systems has been demonstrated in superconducting circuits and in semiconductor quantum dots. This has paved the way to investigate solid-state systems for quantum information processing with the potential benefit of scalability compared to other systems based on atoms, ions and photons. Coherent coupling of superconducting circuits to microwave photons, circuit qua…
▽ More
Quantum coherence in solid-state systems has been demonstrated in superconducting circuits and in semiconductor quantum dots. This has paved the way to investigate solid-state systems for quantum information processing with the potential benefit of scalability compared to other systems based on atoms, ions and photons. Coherent coupling of superconducting circuits to microwave photons, circuit quantum electrodynamics (QED), has opened up new research directions and enabled long distance coupling of qubits. Here we demonstrate how the electromagnetic field of a superconducting microwave resonator can be coupled to a semiconductor double quantum dot. The charge stability diagram of the double dot, typically measured by direct current (DC) transport techniques, is investigated via dispersive frequency shifts of the coupled resonator. This hybrid all-solid-state approach offers the potential to coherently couple multiple quantum dot and superconducting qubits together on one chip, and offers a method for high resolution spectroscopy of semiconductor quantum structures.
△ Less
Submitted 26 August, 2011;
originally announced August 2011.
-
Characterization of a microwave frequency resonator via a nearby quantum dot
Authors:
T. Frey,
P. J. Leek,
M. Beck,
K. Ensslin,
A. Wallraff,
T. Ihn
Abstract:
We present measurements of a hybrid system consisting of a microwave transmission-line resonator and a lateral quantum dot defined on a GaAs heterostructure. The two subsystems are separately characterized and their interaction is studied by monitoring the electrical conductance through the quantum dot. The presence of a strong microwave field in the resonator is found to reduce the resonant condu…
▽ More
We present measurements of a hybrid system consisting of a microwave transmission-line resonator and a lateral quantum dot defined on a GaAs heterostructure. The two subsystems are separately characterized and their interaction is studied by monitoring the electrical conductance through the quantum dot. The presence of a strong microwave field in the resonator is found to reduce the resonant conductance through the quantum dot, and is attributed to electron heating and modulation of the dot potential. We use this interaction to demonstrate a measurement of the resonator transmission spectrum using the quantum dot.
△ Less
Submitted 18 April, 2011;
originally announced April 2011.
-
Fabrication and heating rate study of microscopic surface electrode ion traps
Authors:
N. Daniilidis,
S. Narayanan,
S. A. Möller,
R. Clark,
T. E. Lee,
P. J. Leek,
A. Wallraff,
St. Schulz,
F. Schmidt-Kaler,
H. Häffner
Abstract:
We report heating rate measurements in a microfabricated gold-on-sapphire surface electrode ion trap with trap** height of approximately 240 micron. Using the Doppler recooling method, we characterize the trap heating rates over an extended region of the trap. The noise spectral density of the trap falls in the range of noise spectra reported in ion traps at room temperature. We find that during…
▽ More
We report heating rate measurements in a microfabricated gold-on-sapphire surface electrode ion trap with trap** height of approximately 240 micron. Using the Doppler recooling method, we characterize the trap heating rates over an extended region of the trap. The noise spectral density of the trap falls in the range of noise spectra reported in ion traps at room temperature. We find that during the first months of operation the heating rates increase by approximately one order of magnitude. The increase in heating rates is largest in the ion loading region of the trap, providing a strong hint that surface contamination plays a major role for excessive heating rates. We discuss data found in the literature and possible relation of anomalous heating to sources of noise and dissipation in other systems, namely impurity atoms adsorbed on metal surfaces and amorphous dielectrics.
△ Less
Submitted 15 September, 2010;
originally announced September 2010.
-
Quantum-to-Classical Transition in Cavity Quantum Electrodynamics
Authors:
J. M. Fink,
L. Steffen,
P. Studer,
Lev S. Bishop,
M. Baur,
R. Bianchetti,
D. Bozyigit,
C. Lang,
S. Filipp,
P. J. Leek,
A. Wallraff
Abstract:
The quantum properties of electromagnetic, mechanical or other harmonic oscillators can be revealed by investigating their strong coherent coupling to a single quantum two level system in an approach known as cavity quantum electrodynamics (QED). At temperatures much lower than the characteristic energy level spacing the observation of vacuum Rabi oscillations or mode splittings with one or a few…
▽ More
The quantum properties of electromagnetic, mechanical or other harmonic oscillators can be revealed by investigating their strong coherent coupling to a single quantum two level system in an approach known as cavity quantum electrodynamics (QED). At temperatures much lower than the characteristic energy level spacing the observation of vacuum Rabi oscillations or mode splittings with one or a few quanta asserts the quantum nature of the oscillator. Here, we study how the classical response of a cavity QED system emerges from the quantum one when its thermal occupation -- or effective temperature -- is raised gradually over 5 orders of magnitude. In this way we explore in detail the continuous quantum-to-classical crossover and demonstrate how to extract effective cavity field temperatures from both spectroscopic and time-resolved vacuum Rabi measurements.
△ Less
Submitted 21 October, 2010; v1 submitted 4 March, 2010;
originally announced March 2010.
-
Measurements of the Correlation Function of a Microwave Frequency Single Photon Source
Authors:
D. Bozyigit,
C. Lang,
L. Steffen,
J. M. Fink,
M. Baur,
R. Bianchetti,
P. J. Leek,
S. Filipp,
M. P. da Silva,
A. Blais,
A. Wallraff
Abstract:
At optical frequencies the radiation produced by a source, such as a laser, a black body or a single photon source, is frequently characterized by analyzing the temporal correlations of emitted photons using single photon counters. At microwave frequencies, however, there are no efficient single photon counters yet. Instead, well developed linear amplifiers allow for efficient measurement of the…
▽ More
At optical frequencies the radiation produced by a source, such as a laser, a black body or a single photon source, is frequently characterized by analyzing the temporal correlations of emitted photons using single photon counters. At microwave frequencies, however, there are no efficient single photon counters yet. Instead, well developed linear amplifiers allow for efficient measurement of the amplitude of an electromagnetic field. Here, we demonstrate how the properties of a microwave single photon source can be characterized using correlation measurements of the emitted radiation with such detectors. We also demonstrate the cooling of a thermal field stored in a cavity, an effect which we detect using a cross-correlation measurement of the radiation emitted at the two ends of the cavity.
△ Less
Submitted 19 February, 2010;
originally announced February 2010.
-
Cavity QED with separate photon storage and qubit readout modes
Authors:
P. J. Leek,
M. Baur,
J. M. Fink,
R. Bianchetti,
L. Steffen,
S. Filipp,
A. Wallraff
Abstract:
We present the realization of a cavity quantum electrodynamics setup in which photons of strongly different lifetimes are engineered in different harmonic modes of the same cavity. We achieve this in a superconducting transmission line resonator with superconducting qubits coupled to the different modes. One cavity mode is strongly coupled to a detection line for qubit state readout, while a sec…
▽ More
We present the realization of a cavity quantum electrodynamics setup in which photons of strongly different lifetimes are engineered in different harmonic modes of the same cavity. We achieve this in a superconducting transmission line resonator with superconducting qubits coupled to the different modes. One cavity mode is strongly coupled to a detection line for qubit state readout, while a second long lifetime mode is used for photon storage and coherent quantum operations. We demonstrate sideband based measurement of photon coherence, generation of n photon Fock states and the scaling of the sideband Rabi frequency with the square root of n using a scheme that may be extended to realize sideband based two-qubit logic gates.
△ Less
Submitted 25 November, 2009; v1 submitted 25 November, 2009;
originally announced November 2009.
-
Thermal Excitation of Multi-Photon Dressed States in Circuit Quantum Electrodynamics
Authors:
J. M. Fink,
M. Baur,
R. Bianchetti,
S. Filipp,
M. Göppl,
P. J. Leek,
L. Steffen,
A. Blais,
A. Wallraff
Abstract:
The exceptionally strong coupling realizable between superconducting qubits and photons stored in an on-chip microwave resonator allows for the detailed study of matter-light interactions in the realm of circuit quantum electrodynamics (QED). Here we investigate the resonant interaction between a single transmon-type multilevel artificial atom and weak thermal and coherent fields. We explore up…
▽ More
The exceptionally strong coupling realizable between superconducting qubits and photons stored in an on-chip microwave resonator allows for the detailed study of matter-light interactions in the realm of circuit quantum electrodynamics (QED). Here we investigate the resonant interaction between a single transmon-type multilevel artificial atom and weak thermal and coherent fields. We explore up to three photon dressed states of the coupled system in a linear response heterodyne transmission measurement. The results are in good quantitative agreement with a generalized Jaynes-Cummings model. Our data indicates that the role of thermal fields in resonant cavity QED can be studied in detail using superconducting circuits.
△ Less
Submitted 19 November, 2009;
originally announced November 2009.
-
Dynamics of dispersive single qubit read-out in circuit quantum electrodynamics
Authors:
R. Bianchetti,
S. Filipp,
M. Baur,
J. M. Fink,
M. Göppl,
P. J. Leek,
L. Steffen,
A. Blais,
A. Wallraff
Abstract:
The quantum state of a superconducting qubit nonresonantly coupled to a transmission line resonator can be determined by measuring the quadrature amplitudes of an electromagnetic field transmitted through the resonator. We present experiments in which we analyze in detail the dynamics of the transmitted field as a function of the measurement frequency for both weak continuous and pulsed measurem…
▽ More
The quantum state of a superconducting qubit nonresonantly coupled to a transmission line resonator can be determined by measuring the quadrature amplitudes of an electromagnetic field transmitted through the resonator. We present experiments in which we analyze in detail the dynamics of the transmitted field as a function of the measurement frequency for both weak continuous and pulsed measurements. We find excellent agreement between our data and calculations based on a set of Bloch-type differential equations for the cavity field derived from the dispersive Jaynes-Cummings Hamiltonian including dissipation. We show that the measured system response can be used to construct a measurement operator from which the qubit population can be inferred accurately. Such a measurement operator can be used in tomographic methods to reconstruct single and multiqubit states in ensemble-averaged measurements.
△ Less
Submitted 9 November, 2009; v1 submitted 15 July, 2009;
originally announced July 2009.
-
Climbing the Jaynes-Cummings Ladder and Observing its Sqrt(n) Nonlinearity in a Cavity QED System
Authors:
J. M. Fink,
M. Goeppl,
M. Baur,
R. Bianchetti,
P. J. Leek,
A. Blais,
A. Wallraff
Abstract:
The already very active field of cavity quantum electrodynamics (QED), traditionally studied in atomic systems, has recently gained additional momentum by the advent of experiments with semiconducting and superconducting systems. In these solid state implementations, novel quantum optics experiments are enabled by the possibility to engineer many of the characteristic parameters at will. In cavi…
▽ More
The already very active field of cavity quantum electrodynamics (QED), traditionally studied in atomic systems, has recently gained additional momentum by the advent of experiments with semiconducting and superconducting systems. In these solid state implementations, novel quantum optics experiments are enabled by the possibility to engineer many of the characteristic parameters at will. In cavity QED, the observation of the vacuum Rabi mode splitting is a hallmark experiment aimed at probing the nature of matter-light interaction on the level of a single quantum. However, this effect can, at least in principle, be explained classically as the normal mode splitting of two coupled linear oscillators. It has been suggested that an observation of the scaling of the resonant atom-photon coupling strength in the Jaynes-Cummings energy ladder with the square root of photon number n is sufficient to prove that the system is quantum mechanical in nature. Here we report a direct spectroscopic observation of this characteristic quantum nonlinearity. Measuring the photonic degree of freedom of the coupled system, our measurements provide unambiguous, long sought for spectroscopic evidence for the quantum nature of the resonant atom-field interaction in cavity QED. We explore atom-photon superposition states involving up to two photons, using a spectroscopic pump and probe technique. The experiments have been performed in a circuit QED setup, in which ultra strong coupling is realized by the large dipole coupling strength and the long coherence time of a superconducting qubit embedded in a high quality on-chip microwave cavity.
△ Less
Submitted 11 February, 2009;
originally announced February 2009.
-
Measurement of Autler-Townes and Mollow transitions in a strongly driven superconducting qubit
Authors:
M. Baur,
S. Filipp,
R. Bianchetti,
J. M. Fink,
M. Göppl,
L. Steffen,
P. J. Leek,
A. Blais,
A. Wallraff
Abstract:
We present spectroscopic measurements of the Autler-Townes doublet and the sidebands of the Mollow triplet in a driven superconducting qubit. The ground to first excited state transition of the qubit is strongly pumped while the resulting dressed qubit spectrum is probed with a weak tone. The corresponding transitions are detected using dispersive read-out of the qubit coupled off-resonantly to…
▽ More
We present spectroscopic measurements of the Autler-Townes doublet and the sidebands of the Mollow triplet in a driven superconducting qubit. The ground to first excited state transition of the qubit is strongly pumped while the resulting dressed qubit spectrum is probed with a weak tone. The corresponding transitions are detected using dispersive read-out of the qubit coupled off-resonantly to a microwave transmission line resonator. The observed frequencies of the Autler-Townes and Mollow spectral lines are in good agreement with a dispersive Jaynes-Cummings model taking into account higher excited qubit states and dispersive level shifts due to off-resonant drives.
△ Less
Submitted 23 December, 2008;
originally announced December 2008.
-
Using Sideband Transitions for Two-Qubit Operations in Superconducting Circuits
Authors:
P. J. Leek,
S. Filipp,
P. Maurer,
M. Baur,
R. Bianchetti,
J. M. Fink,
M. Göppl,
L. Steffen,
A. Wallraff
Abstract:
We demonstrate time resolved driving of two-photon blue sideband transitions between superconducting qubits and a transmission line resonator. Using the sidebands, we implement a pulse sequence that first entangles one qubit with the resonator, and subsequently distributes the entanglement between two qubits. We show generation of 75% fidelity Bell states by this method. The full density matrix…
▽ More
We demonstrate time resolved driving of two-photon blue sideband transitions between superconducting qubits and a transmission line resonator. Using the sidebands, we implement a pulse sequence that first entangles one qubit with the resonator, and subsequently distributes the entanglement between two qubits. We show generation of 75% fidelity Bell states by this method. The full density matrix of the two qubit system is extracted using joint measurement and quantum state tomography, and shows close agreement with numerical simulation. The scheme is potentially extendable to a scalable universal gate for quantum computation.
△ Less
Submitted 15 December, 2008;
originally announced December 2008.
-
Dressed Collective Qubit States and the Tavis-Cummings Model in Circuit QED
Authors:
J. M. Fink,
R. Bianchetti,
M. Baur,
M. Goeppl,
L. Steffen,
S. Filipp,
P. J. Leek,
A. Blais,
A. Wallraff
Abstract:
We present an ideal realization of the Tavis-Cummings model in the absence of atom number and coupling fluctuations by embedding a discrete number of fully controllable superconducting qubits at fixed positions into a transmission line resonator. Measuring the vacuum Rabi mode splitting with one, two and three qubits strongly coupled to the cavity field, we explore both bright and dark dressed c…
▽ More
We present an ideal realization of the Tavis-Cummings model in the absence of atom number and coupling fluctuations by embedding a discrete number of fully controllable superconducting qubits at fixed positions into a transmission line resonator. Measuring the vacuum Rabi mode splitting with one, two and three qubits strongly coupled to the cavity field, we explore both bright and dark dressed collective multi-qubit states and observe the discrete square root of N scaling of the collective dipole coupling strength. Our experiments demonstrate a novel approach to explore collective states, such as the W-state, in a fully globally and locally controllable quantum system. Our scalable approach is interesting for solid-state quantum information processing and for fundamental multi-atom quantum optics experiments with fixed atom numbers.
△ Less
Submitted 18 August, 2009; v1 submitted 15 December, 2008;
originally announced December 2008.
-
Two-Qubit State Tomography using a Joint Dispersive Read-Out
Authors:
S. Filipp,
P. Maurer,
P. J. Leek,
M. Baur,
R. Bianchetti,
J. M. Fink,
M. Göppl,
L. Steffen,
J. M. Gambetta,
A. Blais,
A. Wallraff
Abstract:
Quantum state tomography is an important tool in quantum information science for complete characterization of multi-qubit states and their correlations. Here we report a method to perform a joint simultaneous read-out of two superconducting qubits dispersively coupled to the same mode of a microwave transmission line resonator. The non-linear dependence of the resonator transmission on the qubit…
▽ More
Quantum state tomography is an important tool in quantum information science for complete characterization of multi-qubit states and their correlations. Here we report a method to perform a joint simultaneous read-out of two superconducting qubits dispersively coupled to the same mode of a microwave transmission line resonator. The non-linear dependence of the resonator transmission on the qubit state dependent cavity frequency allows us to extract the full two-qubit correlations without the need for single shot read-out of individual qubits. We employ standard tomographic techniques to reconstruct the density matrix of two-qubit quantum states.
△ Less
Submitted 15 December, 2008;
originally announced December 2008.
-
Coplanar Waveguide Resonators for Circuit Quantum Electrodynamics
Authors:
M. Göppl,
A. Fragner,
M. Baur,
R. Bianchetti,
S. Filipp,
J. M. Fink,
P. J. Leek,
G. Puebla,
L. Steffen,
A. Wallraff
Abstract:
We have designed and fabricated superconducting coplanar waveguide resonators with fundamental frequencies from 2 to $9 \rm{GHz}$ and loaded quality factors ranging from a few hundreds to a several hundred thousands reached at temperatures of $20 \rm{mK}$. The loaded quality factors are controlled by appropriately designed input and output coupling capacitors. The measured transmission spectra a…
▽ More
We have designed and fabricated superconducting coplanar waveguide resonators with fundamental frequencies from 2 to $9 \rm{GHz}$ and loaded quality factors ranging from a few hundreds to a several hundred thousands reached at temperatures of $20 \rm{mK}$. The loaded quality factors are controlled by appropriately designed input and output coupling capacitors. The measured transmission spectra are analyzed using both a lumped element model and a distributed element transmission matrix method. The experimentally determined resonance frequencies, quality factors and insertion losses are fully and consistently characterized by the two models for all measured devices. Such resonators find prominent applications in quantum optics and quantum information processing with superconducting electronic circuits and in single photon detectors and parametric amplifiers.
△ Less
Submitted 25 July, 2008;
originally announced July 2008.
-
Charge pum** in carbon nanotube quantum dots
Authors:
M. R. Buitelaar,
V. Kashcheyevs,
P. J. Leek,
V. I. Talyanskii,
C. G. Smith,
D. Anderson,
G. A. C. Jones,
J. Wei,
D. H. Cobden
Abstract:
We investigate charge pum** in carbon nanotube quantum dots driven by the electric field of a surface acoustic wave. We find that at small driving amplitudes, the pumped current reverses polarity as the conductance is tuned through a Coulomb blockade peak using a gate electrode. We study the behavior as a function of wave amplitude, frequency and direction and develop a model in which our resu…
▽ More
We investigate charge pum** in carbon nanotube quantum dots driven by the electric field of a surface acoustic wave. We find that at small driving amplitudes, the pumped current reverses polarity as the conductance is tuned through a Coulomb blockade peak using a gate electrode. We study the behavior as a function of wave amplitude, frequency and direction and develop a model in which our results can be understood as resulting from adiabatic charge redistribution between the leads and quantum dots on the nanotube.
△ Less
Submitted 20 April, 2008;
originally announced April 2008.
-
Observation of Berry's Phase in a Solid State Qubit
Authors:
P. J. Leek,
J. M. Fink,
A. Blais,
R. Bianchetti,
M. Göppl,
J. M. Gambetta,
D. I. Schuster,
L. Frunzio,
R. J. Schoelkopf,
A. Wallraff
Abstract:
In quantum information science, the phase of a wavefunction plays an important role in encoding information. While most experiments in this field rely on dynamic effects to manipulate this information, an alternative approach is to use geometric phase, which has been argued to have potential fault tolerance. We demonstrate the controlled accumulation of a geometric phase, Berry's phase, in a sup…
▽ More
In quantum information science, the phase of a wavefunction plays an important role in encoding information. While most experiments in this field rely on dynamic effects to manipulate this information, an alternative approach is to use geometric phase, which has been argued to have potential fault tolerance. We demonstrate the controlled accumulation of a geometric phase, Berry's phase, in a superconducting qubit, manipulating the qubit geometrically using microwave radiation, and observing the accumulated phase in an interference experiment. We find excellent agreement with Berry's predictions, and also observe a geometry dependent contribution to dephasing.
△ Less
Submitted 1 November, 2007;
originally announced November 2007.
