-
Tuning thermoelectric properties of Sb$_2$Te$_3$-AgSbTe$_2$ nanocomposite thin film -- synergy of band engineering and heat transport modulation
Authors:
Abhishek Ghosh,
Khushboo Agarwal,
Sergio Gonzalez Munoz,
Prashant Bisht,
Chandan K Vishwakarma,
Narinder Kaur,
Mujeeb Ahmad,
Per Erik Vullum,
Branson D. Belle,
Rajendra Singh,
O. V. Kolosov,
Bodh Raj Mehta
Abstract:
The present study demonstrates a large enhancement in the Seebeck coefficient and ultralow thermal conductivity (TE) in Sb$_2$Te$_3$-AgSbTe$_2$ nanocomposite thin film. The addition of Ag leads to the in-situ formation of AgSbTe$_2$ secondary phase nanoaggregates in the Sb$_2$Te$_3$ matrix during the growth resulting in a large Seebeck coefficient and reduction of the thermal conductivity. A serie…
▽ More
The present study demonstrates a large enhancement in the Seebeck coefficient and ultralow thermal conductivity (TE) in Sb$_2$Te$_3$-AgSbTe$_2$ nanocomposite thin film. The addition of Ag leads to the in-situ formation of AgSbTe$_2$ secondary phase nanoaggregates in the Sb$_2$Te$_3$ matrix during the growth resulting in a large Seebeck coefficient and reduction of the thermal conductivity. A series of samples with different amounts of minor AgSbTe$_2$ phases are prepared to optimize the TE performance of Sb$_2$Te$_3$ thin films. Based on the experimental and theoretical evidence, it is concluded that a small concentration of Ag promotes the band flattening and induces a sharp resonate-like state deep inside the valence band of Sb$_2$Te$_3$, concurrently modifying the density of states (DOS) of the composite sample. In addition, the electrical potential barrier introduced by the band offset between the host TE matrix and the secondary phases promotes strong energy-dependent carrier scattering in the composite sample, which is also responsible for enhanced TE performance. A contemporary approach based on scanning thermal microscopy is performed to experimentally obtain thermal conductivity values of both the in-plane and cross-plane directions, showing a reduced in-plane thermal conductivity value by ~ 58% upon incorporating the AgSbTe$_2$ phase in the Sb$_2$Te$_3$ matrix. Benefitting from the synergistic manipulation of electrical and thermal transport, a large ZT value of 2.2 is achieved at 375 K. The present study indicates the importance of a combined effect of band structure modification and energy-dependent charge carrier scattering along with reduced thermal conductivity for enhancing TE properties.
△ Less
Submitted 30 May, 2023;
originally announced May 2023.
-
Direct Map** of Local Seebeck Coefficient in 2D Material Nanostructures via Scanning Thermal Gate Microscopy
Authors:
Achim Harzheim,
Charalambos Evangeli,
Oleg V. Kolosov,
Pascal Gehring
Abstract:
Local variations in the Seebeck coefficient in low-dimensional materials-based nanostructures and devices play a major role in their thermoelectric performance. Unfortunately, currently most thermoelectric measurements probe the aggregate characteristics of the device as a whole, failing to observe the effects of the local variations and internal structure. Such variations can be caused by local d…
▽ More
Local variations in the Seebeck coefficient in low-dimensional materials-based nanostructures and devices play a major role in their thermoelectric performance. Unfortunately, currently most thermoelectric measurements probe the aggregate characteristics of the device as a whole, failing to observe the effects of the local variations and internal structure. Such variations can be caused by local defects, geometry, electrical contacts or interfaces and often substantially influence thermoelectric properties, most profoundly in two-dimensional (2D) materials. Here, we use Scanning Thermal Gate Microscopy (STGM), a non-invasive method not requiring an electrical contact between the nanoscale tip and the probed sample, to obtain nanoscale resolution 2D maps of the thermovoltage in graphene samples. We investigate a junction formed between single-layer and bilayer graphene and identify the impact of internal strain and Fermi level pinning by the contacts using a deconvolution method to directly map the local Seebeck coefficient. The new approach paves the way for an in-depth understanding of thermoelectric behaviour and phenomena in 2D materials nanostructures and devices.
△ Less
Submitted 6 May, 2020;
originally announced May 2020.
-
Efficient heating of single-molecule junctions for thermoelectric studies at cryogenic temperatures
Authors:
Pascal Gehring,
Martijn van der Star,
Charalambos Evangeli,
Jennifer J. Le Roy,
Lapo Bogani,
Oleg V. Kolosov,
Herre S. J. van der Zant
Abstract:
The energy dependent thermoelectric response of a single molecule contains valuable information about its transmission function and its excited states. However, measuring it requires devices that can efficiently heat up one side of the molecule while being able to tune its electrochemical potential over a wide energy range. Furthermore, to increase junction stability devices need to operate at cry…
▽ More
The energy dependent thermoelectric response of a single molecule contains valuable information about its transmission function and its excited states. However, measuring it requires devices that can efficiently heat up one side of the molecule while being able to tune its electrochemical potential over a wide energy range. Furthermore, to increase junction stability devices need to operate at cryogenic temperatures. In this work we report on a new device architecture to study the thermoelectric properties and the conductance of single molecules simultaneously over a wide energy range. We employ a sample heater in direct contact with the metallic electrodes contacting the single molecule which allows us to apply temperature biases up to $ΔT = 60$K with minimal heating of the molecular junction. This makes these devices compatible with base temperatures $T_\mathrm{bath} <2$K and enables studies in the linear ($ΔT \ll T_\mathrm{molecule}$) and non-linear ($ΔT \gg T_\mathrm{molecule}$) thermoelectric transport regimes.
△ Less
Submitted 5 July, 2019;
originally announced July 2019.
-
Geometrically Enhanced Thermoelectric Effects in Graphene Nanoconstrictions
Authors:
Achim Harzheim,
Jean Spiece,
Charalambos Evangeli,
Edward McCann,
Vladimir Falko,
Yuewen Sheng,
Jamie H. Warner,
G. Andrew D. Briggs,
Jan A. Mol,
Pascal Gehring,
Oleg V. Kolosov
Abstract:
The influence of nanostructuring and quantum confinement on the thermoelectric properties of materials has been extensively studied. While this has made possible multiple breakthroughs in the achievable figure of merit, classical confinement, and its effect on the local Seebeck coefficient has mostly been neglected, as has the Peltier effect in general due to the complexity of measuring small temp…
▽ More
The influence of nanostructuring and quantum confinement on the thermoelectric properties of materials has been extensively studied. While this has made possible multiple breakthroughs in the achievable figure of merit, classical confinement, and its effect on the local Seebeck coefficient has mostly been neglected, as has the Peltier effect in general due to the complexity of measuring small temperature gradients locally. Here we report that reducing the width of a graphene channel to 100 nm changes the Seebeck coefficient by orders of magnitude. Using a scanning thermal microscope allows us to probe the local temperature of electrically contacted graphene two-terminal devices or to locally heat the sample. We show that constrictions in mono- and bilayer graphene facilitate a spatially correlated gradient in the Seebeck and Peltier coefficient, as evidenced by the pronounced thermovoltage $V_{th}$ and heating/cooling response $ΔT_{Peltier}$, respectively. This geometry dependent effect, which has not been reported previously in 2D materials, has important implications for measurements of patterned nanostructures in graphene and points to novel solutions for effective thermal management in electronic graphene devices or concepts for single material thermocouples.
△ Less
Submitted 29 November, 2018;
originally announced November 2018.
-
Correlation of structural, nanomechanical and electrostatic properties of single and few-layers MoS2
Authors:
Benjamin J. Robinson,
Cristina E. Giusca,
Yurema Teijeiro Gonzalez,
Nicholas D. Kay,
Olga Kazakova,
Oleg V. Kolosov
Abstract:
We have decoupled the intrinsic optical and electrostatic effects arising in monolayer and few-layer molybdenum disulphide from those influenced by the flake-substrate interaction.
We have decoupled the intrinsic optical and electrostatic effects arising in monolayer and few-layer molybdenum disulphide from those influenced by the flake-substrate interaction.
△ Less
Submitted 26 April, 2018;
originally announced April 2018.
-
Field-Effect Control of Graphene-Fullerene Thermoelectric Nanodevices
Authors:
Pascal Gehring,
Achim Harzheim,
Jean Spièce,
Yuewen Sheng,
Gregory Rogers,
Charalambos Evangeli,
Aadarsh Mishra,
Benjamin J. Robinson,
Kyriakos Porfyrakis,
Jamie H. Warner,
Oleg V. Kolosov,
G. Andrew D. Briggs,
Jan A. Mol
Abstract:
Although it was demonstrated that discrete molecular levels determine the sign and magnitude of the thermoelectric effect in single-molecule junctions, full electrostatic control of these levels has not been achieved to date. Here, we show that graphene nanogaps combined with gold microheaters serve as a testbed for studying single-molecule thermoelectricity. Reduced screening of the gate electric…
▽ More
Although it was demonstrated that discrete molecular levels determine the sign and magnitude of the thermoelectric effect in single-molecule junctions, full electrostatic control of these levels has not been achieved to date. Here, we show that graphene nanogaps combined with gold microheaters serve as a testbed for studying single-molecule thermoelectricity. Reduced screening of the gate electric field compared to conventional metal electrodes allows control of the position of the dominant transport orbital by hundreds of meV. We find that the power factor of graphene-fullerene junctions can be tuned over several orders of magnitude to a value close to the theoretical limit of an isolated Breit-Wigner resonance. Furthermore, our data suggest that the power factor of an isolated level is only given by the tunnel coupling to the leads and temperature. These results open up new avenues for exploring thermoelectricity and charge transport in individual molecules and highlight the importance of level alignment and coupling to the electrodes for optimum energy conversion in organic thermoelectric materials.
△ Less
Submitted 23 October, 2017;
originally announced October 2017.
-
Shear Forces and Heat Conductance in Nanoscale Junctions
Authors:
B. J. Robinson,
M. E. Pumarol,
O. V. Kolosov
Abstract:
Nanoscale solid-solid contacts define a wealth of material behaviours from the electrical and thermal conductivity in modern electronic devices to friction and losses in micro- and nanoelectromechanical systems. For modern ultra-high integration processor chips, power electronic devices and thermoelectrics one of the most essential, but thus far most challenging, aspects is the assessment of the h…
▽ More
Nanoscale solid-solid contacts define a wealth of material behaviours from the electrical and thermal conductivity in modern electronic devices to friction and losses in micro- and nanoelectromechanical systems. For modern ultra-high integration processor chips, power electronic devices and thermoelectrics one of the most essential, but thus far most challenging, aspects is the assessment of the heat transport at the nanoscale sized interfaces between their components. While this can be effectively addressed by a scanning thermal microscopy, or SThM, which demonstrates the highest spatial resolution to thermal transport to date, SThM quantitative capability is undermined by the poorly defined nature of the nanoscale contact between the probe tip and the sample. Here we show that simultaneous measurements of the shear force and the heat flow in the probe-sample junction shows distinct correlation between thermal conductance and maximal shear force in the junction for multiple probe-material combinations. Quantitative analysis of this correlation confirmed the intrinsic ballistic nature of the heat transport in the tip-surface nanoscale contact suggesting that they are, ultimately, composed of near-atomic sized regions.
Furthermore, in analogy to the Wiedemann-Franz law, which links electrical and thermal conductivity in metals, we suggest and experimentally confirm a general relation that links shear strength and thermal conductance in nanoscale contacts via the fundamental material properties of heat capacity and heat carrier group velocity, thus opening new avenues for quantitative exploration of thermal transport on the nanoscale.
△ Less
Submitted 27 March, 2017; v1 submitted 7 September, 2015;
originally announced September 2015.
-
Nanoscale Map** of Nanosecond Time-scale Electro-Mechanical Phenomena in Graphene NEMS
Authors:
Nicholas D. Kay,
Peter D. Tovee,
Benjamin J. Robinson,
Konstantin S. Novoselov,
Oleg V. Kolosov
Abstract:
Atomically thin layers of two-dimensional (2D) materials such as graphene, MoS2 and h-BN have immense potential as sensors and electronic devices thanks to their highly desirable electronic, mechanical, optical and heat transport properties. In particular their extreme stiffness, tensile strength and low density allows for high frequency electronic devices, resonators and ultra-sensitive detectors…
▽ More
Atomically thin layers of two-dimensional (2D) materials such as graphene, MoS2 and h-BN have immense potential as sensors and electronic devices thanks to their highly desirable electronic, mechanical, optical and heat transport properties. In particular their extreme stiffness, tensile strength and low density allows for high frequency electronic devices, resonators and ultra-sensitive detectors providing realistic avenues for down-scaling electronic devices and nanoelectromechanical systems (NEMS). Whilst nanoscale morphology and electronic properties of 2D materials can be studied using existing electron or scanning probe microscopy approaches, time-dependant phenomena on the ns and shorter time-scales cannot be readily explored. Here we use the heterodyne principle to reach into this ns time-scale and create a local nanoscale probe for electrostatically induced actuation of a graphene resonator, with amplitude sensitivity down to pm range and time sensitivity in the ns range. We experimentally observed response times of 20-120 ns for resonators with beam lengths of 180 nm to 2.5 um in line with the theoretical predictions for such NEMS devices.
△ Less
Submitted 2 September, 2015;
originally announced September 2015.
-
Time dynamics of photothermal vs optoacoustic response in mid IR nanoscale biospectroscopy
Authors:
Peter D. Tovee,
Claire Tinker-Mill,
Kevin Kjoller,
David Allsop,
Peter Weightman,
Mark Surman,
Michele R. F. Siggel-King,
Andy Wolski,
Oleg V. Kolosov
Abstract:
Infrared (IR) spectroscopy, a well established tool for chemical analysis of diverse materials, has significant potential in biomedical applications. While the spatial resolution of traditional IR spectroscopy is limited by the wavelength of the IR light to the few micrometres, it has been shown that nanoscale chemical analysis can be obtained by detecting IR induced local heating photothermal res…
▽ More
Infrared (IR) spectroscopy, a well established tool for chemical analysis of diverse materials, has significant potential in biomedical applications. While the spatial resolution of traditional IR spectroscopy is limited by the wavelength of the IR light to the few micrometres, it has been shown that nanoscale chemical analysis can be obtained by detecting IR induced local heating photothermal response via Scanning Thermal Microscopy (SThM) or local thermomechanical expansion using Atomic Force Microscopy (AFM). This paper explores the potential of a pulsed ps pulse duration high power free electron laser (FEL) light source for AFM-IR and SThM-IR spectroscopy employing standard AFM and SThM probes. The SThM-IR response was found to have a detrimental strong background signal due to the direct heating of the probe, whereas the AFM IR thermomechanical response allowed to eliminate such a problem for both top down and bottom up illuminations with the FEL IR source. The SThM IR characteristic response time was approximately half that of AFM-IR, in line with finite element analysis simulations. Finally, the advantages and drawbacks of AFM-IR wavelength sensitive spectroscopic response using a ps duration FEL vs a high repetition quantum cascade laser IR source in studies of nanoscale dimension amyloid peptide fibres were explored both experimentally and via finite elements analysis.
△ Less
Submitted 2 September, 2015;
originally announced September 2015.
-
Optical properties of two-dimensional gallium chalcogenide films
Authors:
O. Del Pozo-Zamudio,
S. Schwarz,
M. Sich,
I. A. Akimov,
M. Bayer,
R. C. Schofield,
E. A. Chekhovich,
B. J. Robinson,
N. D. Kay,
O. V. Kolosov,
A. I. Dmitriev,
G. V. Lashkarev,
D. N. Borisenko,
N. N. Kolesnikov,
A. I. Tartakovskii
Abstract:
Gallium chalcogenides are promising building blocks for novel van der Waals heterostructures. We report low-temperature micro-photoluminescence (PL) of GaTe and GaSe films with thickness ranging from from 200 nm to a single unit cell. In both materials, PL shows dramatic decrease by 10$^4$-10$^5$ when film thickness is reduced from 200 to 10 nm. Based on evidence from cw and time-resolved PL, we p…
▽ More
Gallium chalcogenides are promising building blocks for novel van der Waals heterostructures. We report low-temperature micro-photoluminescence (PL) of GaTe and GaSe films with thickness ranging from from 200 nm to a single unit cell. In both materials, PL shows dramatic decrease by 10$^4$-10$^5$ when film thickness is reduced from 200 to 10 nm. Based on evidence from cw and time-resolved PL, we propose a model explaining the PL decrease as a result of non-radiative carrier escape via surface states.
△ Less
Submitted 17 March, 2015; v1 submitted 9 January, 2015;
originally announced January 2015.
-
Nanothermal Characterization of Amorphous and Crystalline Phases in Chalcogenide Thin Films with Scanning Thermal Microscopy
Authors:
J. L. Bosse,
M. Timofeeva,
P. D. Tovee,
B. J. Robinson,
B. D. Huey,
O. V. Kolosov
Abstract:
The thermal properties of amorphous and crystalline phases in chalcogenide phase change materials (PCM) play a key role in device performance for non-volatile random-access memory. Here, we report the nanothermal morphology of amorphous and crystalline phases in laser pulsed GeTe and Ge2Sb2Te5 thin films by scanning thermal microscopy (SThM). By performing SThM measurements and applying quantitati…
▽ More
The thermal properties of amorphous and crystalline phases in chalcogenide phase change materials (PCM) play a key role in device performance for non-volatile random-access memory. Here, we report the nanothermal morphology of amorphous and crystalline phases in laser pulsed GeTe and Ge2Sb2Te5 thin films by scanning thermal microscopy (SThM). By performing SThM measurements and applying quantitative physical models to two film thicknesses, the PCM thermal conductivities and thermal boundary conductances between the PCM and SThM probe are independently estimated for the amorphous and crystalline phase of each stoichiometry.
△ Less
Submitted 18 June, 2014;
originally announced June 2014.
-
Nanomechanical morphology of amorphous, transition, and crystalline domains in phase change memory thin films
Authors:
James L. Bosse,
Ilya Grishin,
Bryan D. Huey,
Oleg V. Kolosov
Abstract:
In the search for phase change materials (PCM) that may rival traditional random access memory, a complete understanding of the amorphous to crystalline phase transition is required. For the well-known Ge2Sb2Te5 (GST) and GeTe (GT) chalcogenides, which display nucleation and growth dominated crystallization kinetics, respectively, this work explores the nanomechanical morphology of amorphous and c…
▽ More
In the search for phase change materials (PCM) that may rival traditional random access memory, a complete understanding of the amorphous to crystalline phase transition is required. For the well-known Ge2Sb2Te5 (GST) and GeTe (GT) chalcogenides, which display nucleation and growth dominated crystallization kinetics, respectively, this work explores the nanomechanical morphology of amorphous and crystalline phases in 50 nm thin films. Subjecting these PCM specimens to a lateral thermal gradient spanning the crystallization temperature allows for a detailed morphological investigation. Surface and depth-dependent analyses of the resulting amorphous, transition and crystalline regions are achieved with shallow angle cross-sections, uniquely implemented with beam exit Ar ion polishing. To resolve the distinct phases, ultrasonic force microscopy (UFM) with simultaneous topography is implemented revealing a relative stiffness contrast between the amorphous and crystalline phases of 14% for the free film surface and 20% for the cross-sectioned surface. Nucleation is observed to occur preferentially at the PCM-substrate and free film interface for both GST and GT, while fine subsurface structures are found to be sputtering direction dependent. Combining surface and cross-section nanomechanical map** in this manner allows 3D analysis of microstructure and defects with nanoscale lateral and depth resolution, applicable to a wide range of materials characterization studies where the detection of subtle variations in elastic modulus or stiffness are required.
△ Less
Submitted 10 June, 2014;
originally announced June 2014.
-
Nanoscale resolution scanning thermal microscopy with thermally conductive nanowire probes
Authors:
Maria Timofeeva,
Alexey Bolshakov,
Peter D. Tovee,
Dagou A. Zeze,
Vladimir G. Dubrovskii,
Oleg V. Kolosov
Abstract:
Scanning thermal microscopy (SThM) - a type of scanning probe microscopy that allows map** thermal transport and temperatures in nanoscale devices, is becoming a key approach that may help to resolve heat dissipation problems in modern processors and develop new thermoelectric materials. Unfortunately, performance of current SThM implementations in measurement of high thermal conductivity materi…
▽ More
Scanning thermal microscopy (SThM) - a type of scanning probe microscopy that allows map** thermal transport and temperatures in nanoscale devices, is becoming a key approach that may help to resolve heat dissipation problems in modern processors and develop new thermoelectric materials. Unfortunately, performance of current SThM implementations in measurement of high thermal conductivity materials continues to me limited. The reason for these limitations is two-fold - first, SThM measurements of high thermal conductivity materials need adequate high thermal conductivity of the probe apex, and secondly, the quality of thermal contact between the probe and the sample becomes strongly affected by the nanoscale surface corrugations of the studied sample. In this paper we develop analytical models of the SThM approach that can tackle these complex problems - by exploring high thermal conductivity nanowires as a tip apex, and exploring contact resistance between the SThM probe and studied surface, the latter becoming particularly important when both tip and surface have high thermal conductivities. We develop analytical model supported by the finite element analysis simulations and by the experimental tests of SThM prototype using carbon nanotube (CNT) at the tip apex as a heat conducting nanowire. These results elucidate vital relationships between the performance of the probe in SThM from one side and thermal conductivity, geometry of the probe and its components from the other, providing pathway for overcoming current limitations of SThM.
△ Less
Submitted 8 September, 2013;
originally announced September 2013.
-
Ultra High Thermal Resolution Scanning Probe Microscopy via Carbon Nanotube Tipped Thermal Probes
Authors:
Peter D. Tovee,
Manuel E. Pumarol,
Mark C. Rosamond,
Robert Jones,
Michael C. Petty,
Dagou A. Zeze,
Oleg V. Kolosov
Abstract:
We present a new concept of scanning thermal nanoprobe that utilizes the extreme thermal conductance of a carbon nanotube (CNT) to channel heat between the probe and the sample. The integration of CNT in scanning thermal microscopy (SThM) overcomes the main drawbacks of standard SThM probes, where the low thermal conductance of the apex SThM probe is the main limiting factor. The integration of CN…
▽ More
We present a new concept of scanning thermal nanoprobe that utilizes the extreme thermal conductance of a carbon nanotube (CNT) to channel heat between the probe and the sample. The integration of CNT in scanning thermal microscopy (SThM) overcomes the main drawbacks of standard SThM probes, where the low thermal conductance of the apex SThM probe is the main limiting factor. The integration of CNT (CNT- SThM) extends SThM sensitivity to thermal transport measurement in higher thermal conductivity materials such as metals, semiconductors and ceramics, while also improving the spatial resolution. Investigation of thermal transport in ultra large scale integration (ULSI) interconnects, using CNT- SThM probe, showed fine details of heat transport in ceramic layer, vital for mitigating electromigration in ULSI metallic current leads. For a few layer graphene, the heat transport sensitivity and spatial resolution of the CNT-SThM probe demonstrated significantly superior thermal resolution compared to that of standard SThM probes achieving 20-30 nm topography and ~30 nm thermal spatial resolution compared to 50-100 nm for standard SThM probes. The outstanding axial thermal conductivity, high aspect ratio and robustness of CNTs can make CNT-SThM the perfect thermal probe for the measurement of nanoscale thermophysical properties and an excellent candidate for the next generation of thermal microscopes.
△ Less
Submitted 27 May, 2013;
originally announced May 2013.
-
Nanoscale resolution immersion scanning thermal microscopy
Authors:
Peter D. Tovee,
Oleg V. Kolosov
Abstract:
Nanoscale thermal properties are becoming of extreme importance for modern electronic circuits that dissipate increasing power on the length scale of few tens of nanometers, and for chemical and physical properties sensors and biosensors using nanoscale sized features. While Scanning Thermal Microscopy (SThM) is known for its ability to probe thermal properties and heat generation with nanoscale r…
▽ More
Nanoscale thermal properties are becoming of extreme importance for modern electronic circuits that dissipate increasing power on the length scale of few tens of nanometers, and for chemical and physical properties sensors and biosensors using nanoscale sized features. While Scanning Thermal Microscopy (SThM) is known for its ability to probe thermal properties and heat generation with nanoscale resolution, until today it was perceived impossible to use it in the liquid environment due to dominating direct heat exchange between microfabricated thermal probe and surrounding liquid that would deteriorate spatial resolution. Nonetheless, our theoretical analysis of SThM in liquids showed that for certain design of SThM probe with resistive heater located near the probe tip, their thermal signal is only moderately affected, by less than half on immersion in a dodecane environment. More significantly, its spatial resolution, surprisingly, would remain practically unaffected, and the thermal contact between the tip apex and the studied sample would be beneficially improved. Our experimental trials of such immersion SThM, or iSThM, were fully successful and here we report for the first time nanoscale SThM measurements of thermal conductivity of Ultra Large Scale Integration polymerceramic metal interconnects with the spatial thermal resolution down to 50 nm. Further studies of heat transport in nanoscale graphite flakes in iSThM suggested, in particular, that highly anisotropic thermal conductivity in graphene layers may play significant role in the nanoscale thermal transport in liquid environment. New iSThM opens a wide range of applications from noncontact measurements of thermal transport in semiconductor devices to exploring graphene energy storage, catalytic reactions and heat generation in biological systems.
△ Less
Submitted 6 June, 2013; v1 submitted 11 March, 2013;
originally announced March 2013.
