-
On a Possibility to Measure the Magnetic Field Inside the CMS Yoke Elements
Authors:
V. I. Klyukhin,
R. P. Smith,
B. Curé,
C. Lesmond
Abstract:
A procedure to measure the magnetic field inside the CMS yoke elements is considered. Fast discharge of the CMS coil can be used to induce voltages in flux loops installed around selected elements of the CMS yoke. By sampling the voltage induced in any one loop, and integrating the voltage waveform over the time of the discharge, the total initial flux in the loop can be measured. The average valu…
▽ More
A procedure to measure the magnetic field inside the CMS yoke elements is considered. Fast discharge of the CMS coil can be used to induce voltages in flux loops installed around selected elements of the CMS yoke. By sampling the voltage induced in any one loop, and integrating the voltage waveform over the time of the discharge, the total initial flux in the loop can be measured. The average value of the magnetic field in the yoke element normal to the plane of the flux loop is obtained by dividing the measured value of the flux by the known area enclosed by the loop and the number of turns in the loop.
△ Less
Submitted 1 February, 2022;
originally announced February 2022.
-
Comparison of the Baseline and the Minimal Steel Yoke Superconducting Magnets for the Future Circular Hadron-Hadron Collider
Authors:
V. I. Klyukhin,
A. Ball,
C. P. Berriaud,
E. Bielert,
B. Curé,
A. Dudarev,
A. Gaddi,
H. Gerwig,
A. Hervé,
M. Mentink,
H. Pais Da Silva,
U. Wagner,
H. H. J. Ten Kate
Abstract:
The conceptual design study of a hadron Future Circular hadron-hadron Collider (FCC-hh) with a center-of-mass energy of the order of 100 TeV assumes using in the experimental detector the superconducting magnetic system with a central magnetic flux density of an order of 4 T. A superconducting magnet with a minimal steel yoke was proposed as an alternative to the baseline iron-free solenoids. In a…
▽ More
The conceptual design study of a hadron Future Circular hadron-hadron Collider (FCC-hh) with a center-of-mass energy of the order of 100 TeV assumes using in the experimental detector the superconducting magnetic system with a central magnetic flux density of an order of 4 T. A superconducting magnet with a minimal steel yoke was proposed as an alternative to the baseline iron-free solenoids. In a present study, both designs are modeled with Cobham's program TOSCA and compared. All the main parameters are discussed.
△ Less
Submitted 18 January, 2022;
originally announced January 2022.
-
Field integrals for the ATLAS tracking volume
Authors:
V. I. Klyukhin,
A. Poppleton,
J. Schmitz
Abstract:
The magnetic field integrals connected with the momentum resolution are calculated for the ATLAS inner tracking volume in a range of pseudorapidity $|η| < 3$ for the cases of `ideal' and inhomogeneous solenoid fields. In the latest case, the magnetic field map is extracted from POISSON calculations with help of an interface program POISGT. The tracking volume is restricted by a length of 6.8 m and…
▽ More
The magnetic field integrals connected with the momentum resolution are calculated for the ATLAS inner tracking volume in a range of pseudorapidity $|η| < 3$ for the cases of `ideal' and inhomogeneous solenoid fields. In the latest case, the magnetic field map is extracted from POISSON calculations with help of an interface program POISGT. The tracking volume is restricted by a length of 6.8 m and by a radius of 1.06 m. The solenoid coil with an active length of 6.3 m and with an inner radius of 1.23 m produces the magnetic flux density of 2 T in the center of the coil.
△ Less
Submitted 1 August, 2018;
originally announced August 2018.
-
On a possibility to extract a signal from heavy gluino cascade decays via isolated muon detection at the LHC energies
Authors:
V. I. Klyukhin,
A. A. Neushkin,
A. A. Sokolov
Abstract:
800 GeV gluino pair production is simulated using ISASUSY 1.1 MC-program. The cascade decay of the gluino into two lightest neutralinos, $\widetilde{g} \rightarrow \widetildeχ_2^0 X$, $\widetildeχ_2^0 \rightarrow μ^+ μ^- \widetildeχ_1^0$, is studied for a convenient set of SUSY parameters: $μ$ = 200 GeV, tan$β$ = 2, average squark masses of 1600 GeV, charged Higgs mass of 500 GeV, and top quark ma…
▽ More
800 GeV gluino pair production is simulated using ISASUSY 1.1 MC-program. The cascade decay of the gluino into two lightest neutralinos, $\widetilde{g} \rightarrow \widetildeχ_2^0 X$, $\widetildeχ_2^0 \rightarrow μ^+ μ^- \widetildeχ_1^0$, is studied for a convenient set of SUSY parameters: $μ$ = 200 GeV, tan$β$ = 2, average squark masses of 1600 GeV, charged Higgs mass of 500 GeV, and top quark mass of 140 GeV. With such parameters the mass difference between $\widetildeχ_2^0$ and $\widetildeχ_1^0$ is less than the mass of Z. As a background, $t\bar{t}$, Z + jets, WW, WZ and ZZ events were generated using ISAJET 6.50 MC-program. The granularities and energy resolutions of the calorimeters in the pseudorapidity range of $\midη\mid$ < 5 are taken into account. If missing transverse momentum is greater than 200 GeV, the number of jets in the calorimeters is 4 or more, the invariant mass of two isolated muons is less than 80 GeV, the background in the muon transverse momentum distribution is negligible.
△ Less
Submitted 30 January, 2017;
originally announced January 2017.
-
Measuring the Magnetic Flux Density with Flux Loops and Hall Probes in the CMS Magnet Flux Return Yoke
Authors:
B. Curé,
N. Amapane,
A. Ball,
A. Gaddi,
H. Gerwig,
A. Hervé,
V. I. Klyukhin,
R. Loveless,
M. Mulders
Abstract:
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its distinctive features include a 4 T superconducting solenoid with 6-m-diameter by 12.5-m-length free bore, enclosed inside a 10,000-ton return yoke made of construction steel. The flux return yoke consists of five dodecagonal three-layered barrel whee…
▽ More
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its distinctive features include a 4 T superconducting solenoid with 6-m-diameter by 12.5-m-length free bore, enclosed inside a 10,000-ton return yoke made of construction steel. The flux return yoke consists of five dodecagonal three-layered barrel wheels and four end-cap disks at each end comprised of steel blocks up to 620 mm thick, which serve as the absorber plates of the muon detection system. To measure the field in and around the steel, a system of 22 flux loops and 82 3-D Hall sensors is installed on the return yoke blocks. A TOSCA 3-D model of the CMS magnet is developed to describe the magnetic field everywhere outside the tracking volume that was measured with the field-map** machine. The voltages induced in the flux loops by the magnetic flux changing during the CMS magnet standard ramps down are measured with six 16-bit DAQ modules. The off-line integration of the induced voltages reconstructs the magnetic flux density in the yoke steel blocks at the operational magnet current of 18.164 kA. The results of the flux loop measurements during three magnet ramps down are presented and discussed.
△ Less
Submitted 7 November, 2016;
originally announced November 2016.
-
Validation of the CMS Magnetic Field Map
Authors:
V. I. Klyukhin,
N. Amapane,
A. Ball,
B. Curé,
A. Gaddi,
H. Gerwig,
M. Mulders,
V. Calvelli,
A. Hervé,
R. Loveless
Abstract:
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its distinctive features include a 4 T superconducting solenoid with 6-m-diameter by 12.5-m-length free bore, enclosed inside a 10,000-ton return yoke made of construction steel. The return yoke consists of five dodecagonal three-layered barrel wheels an…
▽ More
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its distinctive features include a 4 T superconducting solenoid with 6-m-diameter by 12.5-m-length free bore, enclosed inside a 10,000-ton return yoke made of construction steel. The return yoke consists of five dodecagonal three-layered barrel wheels and four end-cap disks at each end comprised of steel blocks up to 620 mm thick, which serve as the absorber plates of the muon detection system. To measure the field in and around the steel, a system of 22 flux loops and 82 3-D Hall sensors is installed on the return yoke blocks. A TOSCA 3-D model of the CMS magnet is developed to describe the magnetic field everywhere outside the tracking volume measured with the field-map** machine. The magnetic field description is compared with the measurements and discussed.
△ Less
Submitted 31 May, 2016;
originally announced June 2016.
-
Flux Loop Measurements of the Magnetic Flux Density in the CMS Magnet Yoke
Authors:
V. I. Klyukhin,
N. Amapane,
A. Ball,
B. Curé,
A. Gaddi,
H. Gerwig,
M. Mulders,
A. Hervé,
R. Loveless
Abstract:
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its distinctive features include a 4 T superconducting solenoid with 6-m-diameter by 12.5-m-length free bore, enclosed inside a 10,000-ton return yoke made of construction steel. The return yoke consists of five dodecagonal three-layered barrel wheels an…
▽ More
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its distinctive features include a 4 T superconducting solenoid with 6-m-diameter by 12.5-m-length free bore, enclosed inside a 10,000-ton return yoke made of construction steel. The return yoke consists of five dodecagonal three-layered barrel wheels and four end-cap disks at each end comprised of steel blocks up to 620 mm thick, which serve as the absorber plates of the muon detection system. To measure the field in and around the steel, a system of 22 flux loops and 82 3-D Hall sensors is installed on the return yoke blocks. A TOSCA 3-D model of the CMS magnet is developed to describe the magnetic field everywhere outside the tracking volume measured with the field-map** machine. The first attempt is made to measure the magnetic flux density in the steel blocks of the CMS magnet yoke using the standard magnet discharge with the current ramp down speed of 1.5 A/s.
△ Less
Submitted 27 May, 2016;
originally announced May 2016.
-
Superconducting Magnet with a Minimal Steel Yoke for the Future Circular Collider Detector
Authors:
V. I. Klyukhin,
A. Hervé,
A. Ball,
B. Curé,
A. Dudarev,
A. Gaddi,
H. Gerwig,
M. Mentink,
H. Pais Da Silva,
G. Rolando,
H. H. J. Ten Kate,
C. P. Berriaud
Abstract:
The conceptual design study of a Future Circular hadron-hadron Collider (FCC-hh) with a center-of-mass energy of the order of 100 TeV, assumed to be constructed in a new tunnel of 80-100 km circumference, includes the determination of the basic requirements for its detectors. A superconducting solenoid magnet of 12-m-diameter inner bore with the central magnetic flux density of 6 T, in combination…
▽ More
The conceptual design study of a Future Circular hadron-hadron Collider (FCC-hh) with a center-of-mass energy of the order of 100 TeV, assumed to be constructed in a new tunnel of 80-100 km circumference, includes the determination of the basic requirements for its detectors. A superconducting solenoid magnet of 12-m-diameter inner bore with the central magnetic flux density of 6 T, in combination with two superconducting dipole magnets and two conventional toroid magnets is proposed for an FCC-hh experimental setup. The coil of 23.468 m length has seven 3.35-m-long modules included into one cryostat. The steel yoke with a mass of 22.6 kt consists of two barrel layers of 0.5 m radial thickness and a 0.7-m-thick nose disk and four 0.6-m-thick end-cap disks each side. The outer diameter of the yoke is 17.7 m. The full length of the magnetic system is 62.6 m. The air gaps between the end-cap disks provide for the installation of the muon chambers up to an absolute pseudorapidity about 2.7. The superconducting dipole magnets provide measurement of charged particle momenta in the absolute pseudorapidity region greater than 3. The conventional forward muon spectrometer allows muon identification in the absolute pseudorapidity region from 2.7 to 5. The magnet is modeled with the program TOSCA from Cobham CTS Limited. The total current in the superconducting solenoid coil is 123 MA-turns; the stored energy is 41.8 GJ. The axial force acting on each end-cap is 450 MN. The stray field is 13.7 mT at a radius of 50 m from the coil axis, and 5.2 mT at a radius of 100 m. Many other parameters are presented and discussed.
△ Less
Submitted 8 August, 2016; v1 submitted 27 May, 2016;
originally announced May 2016.
-
Superconducting Magnet with the Reduced Barrel Yoke for the Hadron Future Circular Collider
Authors:
V. I. Klyukhin,
A. Ball,
C. Berriaud,
B. Curé,
A. Dudarev,
A. Gaddi,
H. Gerwig,
A. Hervé,
M. Mentink,
G. Rolando,
H. F. Pais Da Silva,
U. Wagner,
H. H. J. ten Kate
Abstract:
The conceptual design study of a hadron Future Circular Collider (FCC-hh) with a center-of-mass energy of the order of 100 TeV in a new tunnel of 80-100 km circumference assumes the determination of the basic requirements for its detectors. A superconducting solenoid magnet of 12 m diameter inner bore with the central magnetic flux density of 6 T is proposed for a FCC-hh experimental setup. The co…
▽ More
The conceptual design study of a hadron Future Circular Collider (FCC-hh) with a center-of-mass energy of the order of 100 TeV in a new tunnel of 80-100 km circumference assumes the determination of the basic requirements for its detectors. A superconducting solenoid magnet of 12 m diameter inner bore with the central magnetic flux density of 6 T is proposed for a FCC-hh experimental setup. The coil of 24.518 m long has seven 3.5 m long modules included into one cryostat. The steel yoke with a mass of 21 kt consists of two barrel layers of 0.5 m radial thickness, and 0.7 m thick nose disk, four 0.6 m thick end-cap disks, and three 0.8 m thick muon toroid disks each side. The outer diameter of the yoke is 17.7 m; the length without the forward muon toroids is 33 m. The air gaps between the end-cap disks provide the installation of the muon chambers up to the pseudorapidity of \pm 3.5. The conventional forward muon spectrometer provides the measuring of the muon momenta in the pseudorapidity region from \pm 2.7 to \pm 4.6. The magnet modeled with Cobham's program TOSCA. The total Ampere-turns in the superconducting solenoid coil are 127.25 MA-turns. The stored energy is 43.3 GJ. The axial force onto each end-cap is 480 MN. The stray field at the radius of 50 m off the coil axis is 14.1 mT and 5.4 mT at the radius of 100 m. All other parameters presented and discussed.
△ Less
Submitted 6 November, 2015;
originally announced November 2015.
-
Measuring the Magnetic Flux Density in the CMS Steel Yoke
Authors:
V. I. Klyukhin,
N. Amapane,
A. Ball,
B. Curé,
A. Gaddi,
H. Gerwig,
A. Hervé,
M. Mulders,
R. Loveless
Abstract:
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its distinctive features include a 4 T superconducting solenoid with 6-m-diameter by 12.5-m-length free bore, enclosed inside a 10000-ton return yoke made of construction steel. The return yoke consists of five dodecagonal three-layered barrel wheels and…
▽ More
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its distinctive features include a 4 T superconducting solenoid with 6-m-diameter by 12.5-m-length free bore, enclosed inside a 10000-ton return yoke made of construction steel. The return yoke consists of five dodecagonal three-layered barrel wheels and four end-cap disks at each end comprised of steel blocks up to 620 mm thick, which serve as the absorber plates of the muon detection system. Accurate characterization of the magnetic field everywhere in the CMS detector is required. To measure the field in and around the steel, a system of 22 flux-loops and 82 3-D Hall sensors is installed on the return yoke blocks. Fast discharges of the solenoid (190 s time-constant) made during the CMS magnet surface commissioning test at the solenoid central fields of 2.64, 3.16, 3.68 and 4.01 T were used to induce voltages in the flux-loops. The voltages are measured on-line and integrated off-line to obtain the magnetic flux in the steel yoke close to the muon chambers at full excitations of the solenoid. The 3-D Hall sensors installed on the steel-air interfaces give supplementary information on the components of magnetic field and permit to estimate the remanent field in steel to be added to the magnetic flux density obtained by the voltages integration. A TOSCA 3-D model of the CMS magnet is developed to describe the magnetic field everywhere outside the tracking volume measured with the field-map** machine. The results of the measurements and calculations are presented, compared and discussed.
△ Less
Submitted 6 December, 2012;
originally announced December 2012.
-
The CMS Magnetic Field Map Performance
Authors:
V. I. Klyukhin,
N. Amapane,
V. Andreev,
A. Ball,
B. Curé,
A. Hervé,
A. Gaddi,
H. Gerwig,
V. Karimaki,
R. Loveless,
M. Mulders,
S. Popescu,
L. I. Sarycheva,
T. Virdee
Abstract:
The Compact Muon Solenoid (CMS) is a general-purpose detector designed to run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its distinctive featuresinclude a 4 T superconducting solenoid with 6 m diameter by 12.5 m long free bore, enclosed inside a 10000-ton return yoke made of construction steel. Accurate characterization of the magnetic field everywhere in the CMS detector i…
▽ More
The Compact Muon Solenoid (CMS) is a general-purpose detector designed to run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its distinctive featuresinclude a 4 T superconducting solenoid with 6 m diameter by 12.5 m long free bore, enclosed inside a 10000-ton return yoke made of construction steel. Accurate characterization of the magnetic field everywhere in the CMS detector is required. During two major tests of the CMS magnet the magnetic flux density was measured inside the coil in a cylinder of 3.448 m diameter and 7 m length with a specially designed field-map** pneumatic machine as well as in 140 discrete regions of the CMS yoke with NMR probes, 3-D Hall sensors and flux-loops. A TOSCA 3-D model of the CMS magnet has been developed to describe the magnetic field everywhere outside the tracking volume measured with the field-map** machine. A volume based representation of the magnetic field is used to provide the CMS simulation and reconstruction software with the magnetic field values. The value of the field at a given point of a volume is obtained by interpolation from a regular grid of values resulting from a TOSCA calculation or, when available, from a parameterization. The results of the measurements and calculations are presented, compared and discussed.
△ Less
Submitted 4 October, 2011;
originally announced October 2011.
-
Measurement of the CMS Magnetic Field
Authors:
V. I. Klyukhin,
A. Ball,
F. Bergsma,
D. Campi,
B. Curé,
A. Gaddi,
H. Gerwig,
A. Hervé,
J. Korienek,
F. Linde,
C. Lindenmeyer,
R. Loveless,
M. Mulders,
T. Nebel,
R. P. Smith,
D. Stickland,
G. Teafoe,
L. Veillet,
J. K. Zimmerman
Abstract:
The measurement of the magnetic field in the tracking volume inside the superconducting coil of the Compact Muon Solenoid (CMS) detector under construction at CERN is done with a fieldmapper designed and produced at Fermilab. The fieldmapper uses 10 3-D B-sensors (Hall probes) developed at NIKHEF and calibrated at CERN to precision 0.05% for a nominal 4 T field. The precise fieldmapper measurement…
▽ More
The measurement of the magnetic field in the tracking volume inside the superconducting coil of the Compact Muon Solenoid (CMS) detector under construction at CERN is done with a fieldmapper designed and produced at Fermilab. The fieldmapper uses 10 3-D B-sensors (Hall probes) developed at NIKHEF and calibrated at CERN to precision 0.05% for a nominal 4 T field. The precise fieldmapper measurements are done in 33840 points inside a cylinder of 1.724 m radius and 7 m long at central fields of 2, 3, 3.5, 3.8, and 4 T. Three components of the magnetic flux density at the CMS coil maximum excitation and the remanent fields on the steel-air interface after discharge of the coil are measured in check-points with 95 3-D B-sensors located near the magnetic flux return yoke elements. Voltages induced in 22 flux-loops made of 405-turn installed on selected segments of the yoke are sampled online during the entire fast discharge (190 s time-constant) of the CMS coil and integrated offline to provide a measurement of the initial magnetic flux density in steel at the maximum field to an accuracy of a few percent. The results of the measurements made at 4 T are reported and compared with a three-dimensional model of the CMS magnet system calculated with TOSCA.
△ Less
Submitted 3 October, 2011;
originally announced October 2011.
-
Analysis of Eddy Current Distributions in the CMS Magnet Yoke During the Solenoid Discharge
Authors:
V. I. Klyukhin,
D. Campi,
B. Curé,
A. Gaddi,
H. Gerwig,
J. P. Grillet,
A. Hervé,
R. Loveless,
R. P. Smith
Abstract:
Flux loops have been installed on selected segments of the magnetic flux return yoke of the 4 T superconducting coil of the Compact Muon Solenoid (CMS) detector under construction at CERN. Voltages induced in the loops during discharge of the solenoid will be sampled online during the entire discharge and integrated offline to provide a measurement of the initial magnetic flux density in steel at…
▽ More
Flux loops have been installed on selected segments of the magnetic flux return yoke of the 4 T superconducting coil of the Compact Muon Solenoid (CMS) detector under construction at CERN. Voltages induced in the loops during discharge of the solenoid will be sampled online during the entire discharge and integrated offline to provide a measurement of the initial magnetic flux density in steel at the maximum field to an accuracy of a few percent. Although the discharge of the solenoid is rather slow (190 s time constant), the influence of eddy currents induced in the yoke elements should be estimated. The calculation of eddy currents is performed with Vector Fields' program ELEKTRA. The results of the calculations are reported.
△ Less
Submitted 30 September, 2011;
originally announced September 2011.
-
3D Magnetic Analysis of the CMS Magnet
Authors:
V. I. Klyukhin,
D. Campi,
B. Curé,
A. Desirelli,
S. Farinon,
H. Gerwig,
D. Green,
J. P. Grillet,
A. Hervé,
F. Kircher,
B. Levesy,
R. Loveless,
R. P. Smith
Abstract:
The CMS magnetic system consists of a super-conducting solenoid coil, 12.5 m long and 6 m free bore diameter, and of an iron flux-return yoke, which includes the central barrel, two end-caps and the ferromagnetic parts of the hadronic forward calorimeter. The magnetic flux density in the center of the solenoid is 4 T. To carry out the magnetic analysis of the CMS magnetic system, several 3D models…
▽ More
The CMS magnetic system consists of a super-conducting solenoid coil, 12.5 m long and 6 m free bore diameter, and of an iron flux-return yoke, which includes the central barrel, two end-caps and the ferromagnetic parts of the hadronic forward calorimeter. The magnetic flux density in the center of the solenoid is 4 T. To carry out the magnetic analysis of the CMS magnetic system, several 3D models were developed to perform magnetic field and force calculations using the Vector Fields code TOSCA. The analysis includes a study of the general field behavior, the calculation of the forces on the coil generated by small axial, radial displacements and angular tilts, the calculation of the forces on the ferromagnetic parts, the calculation of the fringe field outside the magnetic system, and a study of the field level in the chimneys for the current leads and the cryogenic lines. A procedure to reconstruct the field inside a cylindrical volume starting from the values of the magnetic flux density on the cylinder surface is considered. Special TOSCA-GEANT interface tools have being developed to input the calculated magnetic field into the detector simulation package.
△ Less
Submitted 29 September, 2011;
originally announced September 2011.
-
Develo** the Technique of Measurements of Magnetic Field in the CMS Steel Yoke Elements With Flux-Loops and Hall Probes
Authors:
V. I. Klyukhin,
D. Campi,
B. Curé,
A. Gaddi,
H. Gerwig,
J. P. Grillet,
A. Hervé,
R. Loveless,
R. P. Smith
Abstract:
Compact muon solenoid (CMS) is a general-purpose detector designed to run at the highest luminosity at the CERN large hadron collider (LHC). Its distinctive features include a 4 T superconducting solenoid with 6 m diameter by 12.5 m long free bore, enclosed inside a 10000-ton return yoke made of construction steel. Accurate characterization of the magnetic field everywhere in theCMSdetector, inclu…
▽ More
Compact muon solenoid (CMS) is a general-purpose detector designed to run at the highest luminosity at the CERN large hadron collider (LHC). Its distinctive features include a 4 T superconducting solenoid with 6 m diameter by 12.5 m long free bore, enclosed inside a 10000-ton return yoke made of construction steel. Accurate characterization of the magnetic field everywhere in theCMSdetector, including the large ferromagnetic parts of the yoke, is required. To measure the field in and around ferromagnetic parts, a set of flux-loops and Hall probe sensors will be installed on several of the steel pieces. Fast discharges of the solenoid during system commissioning tests will be used to induce voltages in the flux-loops that can be integrated to measure the flux in the steel at full excitation of the solenoid. The Hall sensors will give supplementary information on the axial magnetic field and permit estimation of the remanent field in the steel after the fast discharge. An experimental R&D program has been undertaken, using a test flux-loop, two Hall sensors, and sample disks made from the same construction steel used for the CMS magnet yoke. A sample disc, assembled with the test flux-loop and the Hall sensors, was inserted between the pole tips of a dipole electromagnet equipped with a computer-controlled power supply to measure the excitation of the steel from full saturation to zero field. The results of the measurements are presented and discussed.
△ Less
Submitted 29 September, 2011;
originally announced September 2011.
-
Special Theory of Super Relativity and a Possibility to Exceed the Speed of Light
Authors:
V. I. Klyukhin
Abstract:
Modification of special theory of relativity is proposed to describe the propagation of signals with superluminal velocity. Modified kinematics and Lorentz transformations of Maxwell's equations are described. A possible experiment on measuring the speed of light for verification of the theory is discussed. It is shown that replacing the maximum speed in special theory of relativity by the neutrin…
▽ More
Modification of special theory of relativity is proposed to describe the propagation of signals with superluminal velocity. Modified kinematics and Lorentz transformations of Maxwell's equations are described. A possible experiment on measuring the speed of light for verification of the theory is discussed. It is shown that replacing the maximum speed in special theory of relativity by the neutrino superluminal velocity measured by the OPERA collaboration leads to lower value of the muon mass reconstructed from the muon decay products with the modified relativistic kinematics. This value is in strong conflict with the precise muon mass measurements that excludes introducing the superluminal velocity of signals into special theory of relativity.
△ Less
Submitted 13 October, 2011; v1 submitted 26 September, 2011;
originally announced September 2011.
