Mitigation of parasitic losses in the quadrupole resonator enabling direct measurements of low residual resistances of SRF samples
Authors:
S. Keckert,
W. Ackermann,
H. De Gersem,
X. Jiang,
A. Ö. Sezgin,
M. Vogel,
M. Wenskat,
R. Kleindienst,
J. Knobloch,
O. Kugeler,
D. Tikhonov
Abstract:
The quadrupole resonator (QPR) is a dedicated sample-test cavity for the RF characterization of superconducting samples in a wide temperature, RF field and frequency range. Its main purpose are high resolution measurements of the surface resistance with direct access to the residual resistance thanks to the low frequency of the first operating quadrupole mode. Besides the well-known high resolutio…
▽ More
The quadrupole resonator (QPR) is a dedicated sample-test cavity for the RF characterization of superconducting samples in a wide temperature, RF field and frequency range. Its main purpose are high resolution measurements of the surface resistance with direct access to the residual resistance thanks to the low frequency of the first operating quadrupole mode. Besides the well-known high resolution of the QPR, a bias of measurement data towards higher values has been observed, especially at higher harmonic quadrupole modes. Numerical studies show that this can be explained by parasitic RF losses on the adapter flange used to mount samples into the QPR. Coating several micrometer of niobium on those surfaces of the stainless steel flange that are exposed to the RF fields significantly reduced this bias, enabling a direct measurement of a residual resistance smaller than 5 n$Ω$ at 2 K and 413 MHz. A constant correction based on simulations was not feasible due to deviations from one measurement to another. However, this issue is resolved given these new results.
△ Less
Submitted 27 October, 2021; v1 submitted 14 October, 2021;
originally announced October 2021.
Structural properties and anisotropic electronic transport in SrIrO3 films
Authors:
K. R. Kleindienst,
K. Wolff,
J. Schubert,
R. Schneider,
D. Fuchs
Abstract:
Perovskite SrIrO3 (SIO) films epitaxially deposited with a thickness of about 60 nm on various substrate materials display nearly strain-relieved state. Films grown on orthorhombic (110) DyScO3 (DSO) are found to display untwinned bulk-like orthorhombic structure. However, film deposition on cubic (001) SrTiO3 induces a twinned growth of SIO. Resistance measurements on the SIO films reveal only we…
▽ More
Perovskite SrIrO3 (SIO) films epitaxially deposited with a thickness of about 60 nm on various substrate materials display nearly strain-relieved state. Films grown on orthorhombic (110) DyScO3 (DSO) are found to display untwinned bulk-like orthorhombic structure. However, film deposition on cubic (001) SrTiO3 induces a twinned growth of SIO. Resistance measurements on the SIO films reveal only weak temperature dependence, where the resistance R increases with decreasing temperature T. Hall measurements show dominant electron-like transport throughout the temperature range from 2 K to 300 K. At 2 K, the electron concentration and resistivity for SIO on STO amount to ne = 1.4*10^20 cm-3 and 1 mohmcm. Interestingly, the film resistance of untwinned SIO on DSO along the [1-10] and the [001] direction differs by up to 25% indicating pronounced anisotropic electronic transport. The anisotropy of the resistance increases with decreasing T and displays a distinct maximum around 86 K. The specific T-dependence is similar to that of the structural anisotropy sqrt(a2+b2)/c of bulk SIO. Therefore, anisotropic electronic transport in SIO is very likely induced by the orthorhombic distortion. Consequently, for twinned SIO films on STO anisotropy vanishes nearly completely. The experimental results show that structural changes are very likely responsible for the observed anisotropic electronic transport. The strong sensitivity of the electronic transport in SIO films may be explained in terms of the narrow electron-like bands in SIO caused by spin-orbit-coupling and orthorhombic distortion.
△ Less
Submitted 29 August, 2018; v1 submitted 22 May, 2018;
originally announced May 2018.
