-
Characterization of superconducting NbTiN films using a Dispersive Fourier Transform Spectrometer
Authors:
B. N. R. Lap,
A. Khudchenko,
R. Hesper,
K. I. Rudakov,
P. Dmitriev,
F. Khan,
V. Koshelets,
A. M. Baryshev
Abstract:
We have built a Terahertz Dispersive Fourier Transform Spectrometer \cite{Birch1987} to study frequency properties of superconducting films used for fabrication of THz detectors. The signal reflected from the tested film is measured in time domain, which allows to separate it from the other reflections. The complex conductivity of the film depends on frequency and determines the reflection coeffic…
▽ More
We have built a Terahertz Dispersive Fourier Transform Spectrometer \cite{Birch1987} to study frequency properties of superconducting films used for fabrication of THz detectors. The signal reflected from the tested film is measured in time domain, which allows to separate it from the other reflections. The complex conductivity of the film depends on frequency and determines the reflection coefficient. By comparing the film reflection in the superconducting state (temperature is below $T_c$) with the reflection of the normal state, we characterise the film quality at terahertz frequencies. The method was applied to 70 and 200nm thick Nb films on a silicon wafer and to 360nm thick NbTiN films on silicon and quartz wafers. The strong-coupling coefficient, $α$, was found to be 3.52 for Nb, and 3.71-4.02 for the NbTiN films. The experimental results were fitted using extended Mattis-Bardeen theory \cite{Noguchi2012} and show a good agreement.
△ Less
Submitted 4 October, 2021;
originally announced October 2021.
-
APEX-SEPIA660 Early Science: Gas at densities above $10^7$ cm$^{-3}$ towards OMC-1
Authors:
A. Hacar,
M. R. Hogerheijde,
D. Harsono,
S. Portegies Zwart,
C. De Breuck,
K. Torstensson,
W. Boland,
A. M. Baryshev,
R. Hesper,
J. Barkhof,
J. Adema,
M. E. Bekema,
A. Koops,
A. Khudchenko,
R. Stark
Abstract:
Context. The star formation rates and stellar densities found in young massive clusters suggest that these stellar systems originate from gas at densities n(H$_2$) $>10^7$ cm$^{-3}$. Until today, however, the physical characterization of this ultra high density material remains largely unconstrained in observations. Aims. We investigated the density properties of the star-forming gas in the OMC-1…
▽ More
Context. The star formation rates and stellar densities found in young massive clusters suggest that these stellar systems originate from gas at densities n(H$_2$) $>10^7$ cm$^{-3}$. Until today, however, the physical characterization of this ultra high density material remains largely unconstrained in observations. Aims. We investigated the density properties of the star-forming gas in the OMC-1 region located in the vicinity of the Orion Nebula Cluster (ONC). Methods. We mapped the molecular emission at 652 GHz in OMC-1 as part of the APEX-SEPIA660 Early Science. Results. We detect bright and extended N$_2$H$^+$ (J=7-6) line emission along the entire OMC-1 region. Comparisons with previous ALMA data of the (J=1-0) transition and radiative transfer models indicate that the line intensities observed in this N$_2$H$^+$ (7-6) line are produced by large mass reservoirs of gas at densities n(H$_2$) $>10^7$ cm$^{-3}$. Conclusions. The first detection of this N$_2$H$^+$ (7-6) line at parsec-scales demonstrates the extreme density conditions of the star-forming gas in young massive clusters such as the ONC. Our results highlight the unique combination of sensitivity and map** capabilities of the new SEPIA660 receiver for the study of the ISM properties at high frequencies.
△ Less
Submitted 26 September, 2020;
originally announced September 2020.
-
Digital compensation of the side-band-rejection ratio in a fully analog 2SB sub-millimeter receiver
Authors:
R. Rodriguez,
R. Finger,
F. P. Mena,
A. Alvear,
R. Fuentes,
A. Khudchenko,
R. Hesper,
A. M. Baryshev,
N. Reyes,
L. Bronfman
Abstract:
In observational radio astronomy, sideband-separating receivers are preferred, particularly under high atmospheric noise, which is usually the case in the sub-millimeter range. However, obtaining a good rejection ratio between the two sidebands is difficult since, unavoidably, imbalances in the different analog components appear. We describe a method to correct these imbalances without making any…
▽ More
In observational radio astronomy, sideband-separating receivers are preferred, particularly under high atmospheric noise, which is usually the case in the sub-millimeter range. However, obtaining a good rejection ratio between the two sidebands is difficult since, unavoidably, imbalances in the different analog components appear. We describe a method to correct these imbalances without making any change in the analog part of the sideband-separating receiver, specifically, kee** the intermediate-frequency hybrid in place. This opens the possibility of implementing the method in any existing receiver. We have built hardware to demonstrate the validity of the method and tested it on a fully analog receiver operating between 600 and 720GHz. We have tested the stability of calibration and performance vs time and after full resets of the receiver. We have performed an error analysis to compare the digital compensation in two configurations of analog receivers, with and without intermediate frequency (IF) hybrid. An average compensated sideband rejection ratio of 46dB is obtained. Degradation of the compensated sideband rejection ratio on time and after several resets of the receiver is minimal. A receiver with an IF hybrid is more robust to systematic errors. Moreover, we have shown that the intrinsic random errors in calibration have the same impact for configuration without IF hybrid and for a configuration with IF hybrid with analog rejection ratio better than 10dB. Compensated rejection ratios above 40dB are obtained even in the presence of high analog rejection. The method is robust allowing its use under normal operational conditions at any telescope. We also demonstrate that a full analog receiver is more robust against systematic errors. Finally, the error bars associated to the compensated rejection ratio are almost independent of whether IF hybrid is present or not.
△ Less
Submitted 11 June, 2018;
originally announced June 2018.
-
Ultra-pure digital sideband separation at sub-millimeter wavelengths
Authors:
R. Finger,
F. P. Mena,
A. Barishev,
A. Khudchenko,
R. Rodriguez,
E. Huaracan,
A. Alvear,
J. Barkhof,
R. Hesper,
L. Bronfman
Abstract:
Deep spectral-line surveys in the mm and sub-mm range can detect thousands of lines per band uncovering the rich chemistry of molecular clouds, star forming regions and circumstellar envelopes, among others objects. The ability to study the faintest features of spectroscopic observation is, nevertheless, limited by a number of factors. The most important are the source complexity (line density), l…
▽ More
Deep spectral-line surveys in the mm and sub-mm range can detect thousands of lines per band uncovering the rich chemistry of molecular clouds, star forming regions and circumstellar envelopes, among others objects. The ability to study the faintest features of spectroscopic observation is, nevertheless, limited by a number of factors. The most important are the source complexity (line density), limited spectral resolution and insufficient sideband (image) rejection (SRR). Dual Sideband (2SB) millimeter receivers separate upper and lower sideband rejecting the unwanted image by about 15 dB, but they are difficult to build and, until now, only feasible up to about 500 GHz (equivalent to ALMA Band 8). For example ALMA Bands 9 (602-720 GHz) and 10 (787-950 GHz) are currently DSB receivers. Aims: This article reports the implementation of an ALMA Band 9 2SB prototype receiver that makes use of a new technique called calibrated digital sideband separation. The new method promises to ease the manufacturing of 2SB receivers, dramatically increase sideband rejection and allow 2SB instruments at the high frequencies currently covered only by Double Sideband (DSB) or bolometric detectors. Methods: We made use of a Field Programmable Gate Array (FPGA) and fast Analog to Digital Converters (ADCs) to measure and calibrate the receiver's front end phase and amplitude imbalances to achieve sideband separation beyond the possibilities of purely analog receivers. The technique could in principle allow the operation of 2SB receivers even when only imbalanced front ends can be built, particularly at very high frequencies. Results: This digital 2SB receiver shows an average sideband rejection of 45.9 dB while small portions of the band drop below 40 dB. The performance is 27 dB (a factor of 500) better than the average performance of the proof-of-concept Band 9 purely-analog 2SB prototype receiver.
△ Less
Submitted 14 October, 2015; v1 submitted 16 September, 2015;
originally announced September 2015.