Showing 1–28 of 28 results for author: Khavasi, A

Steering line waves at a dual metasurface for optical applications

Authors: Haddi Ahmadi, Zahra Ahmadi, Nasrin Razmjooei, Amin Khavasi

Abstract: Line waves are defined as confined edge modes propagating at the interface of dual electromagnetic metasurfaces that preserve mirror reflection symmetries. Previous works have theoretically and practically explored these waves, showing that they occur at microwave regimes and terahertz ranges. It is also demonstrated that line waves can happen when there is a symmetric resistance discontinuity fro… ▽ More Line waves are defined as confined edge modes propagating at the interface of dual electromagnetic metasurfaces that preserve mirror reflection symmetries. Previous works have theoretically and practically explored these waves, showing that they occur at microwave regimes and terahertz ranges. It is also demonstrated that line waves can happen when there is a symmetric resistance discontinuity from negative to positive values and a uniform surface reactance. Line waves are of tunable mode confinement, direction-dependent polarizations, and singular field enhancement. This study presents a graphene patch design and demonstrates that the line waves associated with this structure can travel in the optical domain. Our design consists of a graphene metasurface on an epsilon near zero (ENZ) substrate. While our approach considers both dual reactive impedances and homogenous reactive ones, we only concentrate on line wave utilization in a dual-impedance structure. △ Less

Submitted 6 December, 2022; v1 submitted 8 October, 2022; originally announced October 2022.

Comments: I am not sure about the quality of the work

Analysis of Electromagnetic Scattering from Array of Time-Modulated Graphene Ribbons

Authors: Mahdi Rahmanzadeh, Behzad Rejaei, Amin Khavasi

Abstract: An accurate and fast method is presented for scattering of electromagnetic waves from an array of time-modulated graphene ribbons. We derive a time-domain integral equation for induced surface currents under subwavelength approximation. Using the method of harmonic balance, this equation is solved for a sinusoidal modulation. The solution of the integral equation is then used to obtain the transmi… ▽ More An accurate and fast method is presented for scattering of electromagnetic waves from an array of time-modulated graphene ribbons. We derive a time-domain integral equation for induced surface currents under subwavelength approximation. Using the method of harmonic balance, this equation is solved for a sinusoidal modulation. The solution of the integral equation is then used to obtain the transmission and reflection coefficients of time-modulated graphene ribbon array. The accuracy of the method was verified through comparison with results of full-wave simulations. In contrast with previously reported analysis techniques, our method is extremely fast and can analyze structures with a much higher modulation frequency. The proposed method also provides interesting physical insights useful for designing novel applications and opens up new vistas in the fast design of time-modulated graphene-based devices. △ Less

Submitted 7 October, 2022; originally announced October 2022.

An extended equivalent circuit model for analysis of arrays of sub-wavelength holes perforated in a metallic film

Authors: Mohammad Pasdari-Kia, Mohammad Memarian, Amin Khavasi

Abstract: Periodic arrays of sub-wavelength holes, due to a variety of applications (sensors, polarizers, filters) and unique abilities in manipulating different characteristics of im**ing light, have been the subject of many studies in recent years. This paper presents a new high-precision circuit model to investigate these structures' electromagnetic response, which provides higher accuracy than availab… ▽ More Periodic arrays of sub-wavelength holes, due to a variety of applications (sensors, polarizers, filters) and unique abilities in manipulating different characteristics of im**ing light, have been the subject of many studies in recent years. This paper presents a new high-precision circuit model to investigate these structures' electromagnetic response, which provides higher accuracy than available literature. To develop the model, a multi-mode approach is taken for inside the apertures, and the proposed model is presented in three general forms which are explained in detail. Along with the proposed circuit model, accurate spatial profiles for square and circular apertures are presented in which the transverse components of the electric field are approximated. In this paper, it is shown that structures such as an array of PEC pillars can be analyzed similar to other arrays of apertures, and the circuit model accurately predicts the behavior of these structures. In some practical applications, such as sensors and TCEs (transparent conducting electrodes), the array is embedded in a layered medium, and the circuit model with minor changes and few modifications can analyze these structures with high accuracy. △ Less

Submitted 8 August, 2023; v1 submitted 2 October, 2022; originally announced October 2022.

A Broadband and Compact Millimeter-Wave Imaging System based on Synthetic Aperture Radar

Authors: Fahimeh Sepehripour, Ahmad Shafiei Alavijeh, Mohammad Fakharzadeh, Amin Khavasi

Abstract: In this paper, the design, realization, and demonstration of a broadband millimeter-wave imaging system based on the synthetic aperture radar technique (SAR) are discussed. The proposed system, operating within the frequency range of 25.3-30.8 GHz, consists of a tapered slot antenna as the transmitter and two half-circle antennas as the receivers. The size of the antenna is 19.5 * 8 mm with a maxi… ▽ More In this paper, the design, realization, and demonstration of a broadband millimeter-wave imaging system based on the synthetic aperture radar technique (SAR) are discussed. The proposed system, operating within the frequency range of 25.3-30.8 GHz, consists of a tapered slot antenna as the transmitter and two half-circle antennas as the receivers. The size of the antenna is 19.5 * 8 mm with a maximum gain of 8.5 dB. The transmitter and the receiver antennas are printed on the same board. This feature leads to a highly compact and flexible configuration, enabling the applicability of the proposed imaging system in the handheld devices. Furthermore, it significantly reduces the fabrication cost of the system. The proposed broadband imaging system, being capable of performing 3D real-time imaging with high resolutions, can be easily calibrated for each frequency within the desired range. By performing 3D imaging from metallic objects with different shapes, we experimentally demonstrate the high performance of the proposed system, which offers great potentialities for a broad range of applications such as security, medical diagnostic, concealed object detection, to name a few. △ Less

Submitted 29 May, 2022; originally announced May 2022.

Babinet-Complementary Structures for Implementation of Pseudospin-Polarized Waveguides

Authors: Haddi Ahmadi, Amin Khavasi

Abstract: In this work, we prove a theorem that states the electromagnetic (EM) duality correspondence between eigenmodes of complementary structures, induces counterpropagating spin-polarized states in different types of waveguides where mirror reflection symmetries are preserved around one (or more) arbitrary plane(s). Similar to photonic topological insulators (PTIs), which support topologically non-triv… ▽ More In this work, we prove a theorem that states the electromagnetic (EM) duality correspondence between eigenmodes of complementary structures, induces counterpropagating spin-polarized states in different types of waveguides where mirror reflection symmetries are preserved around one (or more) arbitrary plane(s). Similar to photonic topological insulators (PTIs), which support topologically non-trivial direction-dependent spin polarizations, our pseudospin-polarized systems support one-way states that manifest robustness, however, the advantage of our structures is that they can be implemented in extremely broad bandwidth simply using artificial dual impedance surfaces. Consequently, there is no need to bulk electromagnetic materials. On the basis of our theory, the concept of the pseudospin-polarized waveguide can be realized using Babinet complementary structures, ranging from microwave to THz regime. We design and develop various unidirectional waveguides and spin-filtered feature in the microwave regime is investigated. △ Less

Submitted 15 January, 2022; originally announced January 2022.

Analysis and design of two-dimensional compound metallic metagratings using an analytical method

Authors: Mahdi Rahmanzadeh, Amin Khavasi

Abstract: The recently proposed concept of metagrating enables wavefront manipulation of electromagnetic (EM) waves with unitary efficiency and relatively simple fabrication requirements. Herein, two-dimensional (2D) metagratings composed of a 2D periodic array of rectangular holes in a metallic medium are proposed for diffraction pattern control. We first present an analytical method for diffraction analys… ▽ More The recently proposed concept of metagrating enables wavefront manipulation of electromagnetic (EM) waves with unitary efficiency and relatively simple fabrication requirements. Herein, two-dimensional (2D) metagratings composed of a 2D periodic array of rectangular holes in a metallic medium are proposed for diffraction pattern control. We first present an analytical method for diffraction analysis of 2D compound metallic metagrating (a periodic metallic structure with more than one rectangular hole in each period). Closed-form and analytical expressions are presented for the reflection coefficients of diffracted orders for the first time. Next, we verify the proposed method's results against full-wave simulations and demonstrate their excellent agreement. As a proof of principle, two applications are presented using the proposed analytical method. The first application is a perfect out-of-plane reflector that transfers a normal transverse-magnetic (TM) polarized plane wave to an oblique transverse-electric (TE) polarized plane wave in the $y-z$ plane. The second one is a five-channel beam splitter with an arbitrary power distribution between channels. Using the proposed analytical method, we designed these metagratings without requiring even a single optimization in a full-wave solver. The performance of the designed metagratings is better than previously reported structures in terms of power efficiency and relative distribution error. Our analytical results reveals that 2D metagratings can be used for manipulating EM waves in the plane and out of the plane of incidence with very high efficiency, thereby leading to extensive applications in a wide range of frequencies from microwave to terahertz (THz) regimes. △ Less

Submitted 25 October, 2021; originally announced October 2021.

Magnetoelastic coupling enabled tunability of magnon spin current generation in 2D antiferromagnets

Authors: Nasim Bazazzadeh, Mohammad Hamdi, Sungjoon Park, Amin Khavasi, S. Majid Mohseni, Ali Sadeghi

Abstract: We theoretically investigate the magnetoelastic coupling (MEC) and its effect on magnon transport in two-dimensional antiferromagnets with a honeycomb lattice. MEC coeffcient along with magnetic exchange parameters and spring constants are computed for monolayers of transition metal trichalcogenides with Néel order ($\text{MnPS}_3$ and $\text{VPS}_3$) and zigzag order ($\text{CrSiTe}_3$,… ▽ More We theoretically investigate the magnetoelastic coupling (MEC) and its effect on magnon transport in two-dimensional antiferromagnets with a honeycomb lattice. MEC coeffcient along with magnetic exchange parameters and spring constants are computed for monolayers of transition metal trichalcogenides with Néel order ($\text{MnPS}_3$ and $\text{VPS}_3$) and zigzag order ($\text{CrSiTe}_3$, $\text{NiPS}_3$ and $\text{NiPSe}_3$) by $ab$ $initio$ calculations. Using these parameters, we predict that the spin-Nernst coefficient is significantly enhanced due to magnetoelastic coupling. Our study shows that although Dzyaloshinskii-Moriya interaction can produce spin Nernst effect in these materials, other mechanisms such as magnon-phonon coupling should be taken into account. We also demonstrate that the magnetic anisotropy is an important factor for control of magnon-phonon hybridization and enhancement of the Berry curvature and thus the spin-Nernst coefficient. Our results pave the way towards gate tunable spin current generation in 2D magnets by SNE via electric field modulation of MEC and anisotropy. △ Less

Submitted 18 August, 2021; originally announced August 2021.

Analytical method for the diffraction of an electromagnetic wave by subwavelength graphene ribbons

Authors: Mahdi Rahmanzadeh, Amin Khavasi, Behzad Rejaei

Abstract: Theoretical study of arrays of graphene ribbons is currently of high interest due to its potential application in beam splitters, absorbers, and polarizers. In this paper, an analytical method is presented for diffraction analysis of graphene ribbon arrays. Previous analytical studies were carried out in the regime where the lateral separation between the ribbons is much smaller than the wavelengt… ▽ More Theoretical study of arrays of graphene ribbons is currently of high interest due to its potential application in beam splitters, absorbers, and polarizers. In this paper, an analytical method is presented for diffraction analysis of graphene ribbon arrays. Previous analytical studies were carried out in the regime where the lateral separation between the ribbons is much smaller than the wavelength of the incident wave. As such, they could not be used to calculate the reflection coefficients of higher diffracted orders. By contrast, the method proposed here can predict electromagnetic response of graphene ribbon arrays even when the array constant is larger than the wavelength. To reach our results, we first derive an analytical expression for the surface density of electric current induced on the ribbons by an incident, transverse-magnetic (TM), plane wave. Next, closed-form and analytical expressions are obtained for the reflection coefficients of the zeroth and higher diffracted orders. The results are in excellent agreement with those obtained from full-wave simulations. The method presented facilitates the design of tunable gratings with many potential applications in THz and optics. △ Less

Submitted 31 October, 2020; originally announced November 2020.

Perfect anomalous reflection using compound metallic metagratings

Authors: Mahdi Rahmanzadeh, Amin Khavasi

Abstract: Metagrating is a new concept for wavefront manipulation that, unlike phase gradient metasurfaces, does not suffer from low efficiency and also has a less complicated fabrication process. In this paper, a compound metallic grating (a periodic structure with more than one slit in each period) is proposed for anomalous reflection. The electromagnetic response of this grating is analyzed by a proposed… ▽ More Metagrating is a new concept for wavefront manipulation that, unlike phase gradient metasurfaces, does not suffer from low efficiency and also has a less complicated fabrication process. In this paper, a compound metallic grating (a periodic structure with more than one slit in each period) is proposed for anomalous reflection. The electromagnetic response of this grating is analyzed by a proposed analytical method and then a closed-form and analytical expressions are presented for the reflection coefficients of the higher diffracted orders. The proposed method is verified by full-wave simulations and the results are in excellent agreement. Thanks to the geometrical asymmetry of compound metallic grating, we use it for designing anomalous reflection in the normal incident. Given analytical expressions for reflection coefficients, a perfect anomalous reflector is designed via transferring all the incident power to (-1) diffraction order. The structure designed in this study has an unprecedented near-to-unitary efficiency of 99.9%. Finally, a multi-element compound metallic grating is proposed for reflecting the normal incident to angles of below 30, which is a challenging accomplishment. This excellent performance of compound metallic grating shows its high potential for microwave and terahertz wave-front manipulation applications. △ Less

Submitted 19 December, 2019; originally announced December 2019.

Analog Optical Implementation of Spatial High Pass Filtering Using Evanescent Waves

Authors: Ali Pour Mohammad Qoli Vafa, Parisa Karimi, Amin Khavasi

Abstract: We introduce optical polarization-insensitive high pass filters based on total internal reflection of light at the interface of two dielectric media (1D) and Bragg reflection of a multilayer stack (2D) in transmission mode. The wavevectors in the stopband become coupled to evanescent waves in our design, rather than the zero of a narrow-band resonant mode. This provides remarkable resolution enhan… ▽ More We introduce optical polarization-insensitive high pass filters based on total internal reflection of light at the interface of two dielectric media (1D) and Bragg reflection of a multilayer stack (2D) in transmission mode. The wavevectors in the stopband become coupled to evanescent waves in our design, rather than the zero of a narrow-band resonant mode. This provides remarkable resolution enhancement for edge detection applications. Rigorous analysis based on plane wave expansion is carried out and the results are verified by full-wave numerical simulation. Also for the case of multilayer structure, the thickness of layers is tuned using an optimization algorithm to represent a better approximation of an ideal high pass filter. The application of the designed high pass filters for edge detection of input field profiles is demonstrated for both 1D and 2D operations. The proposed devices are compact and no Fourier lens is required, since the operator is directly implemented in the spatial Fourier domain. △ Less

Submitted 23 November, 2019; originally announced November 2019.

An Analytical and Rigorous Method for Analysis of an Array of Magnetically-Biased Graphene Ribbons

Authors: Mahdi Rahmanzadeh, Behzad Rejaei, Mohammad Memarian, Amin Khavasi

Abstract: A sheet of graphene under magnetic bias attains anisotropic surface conductivity, opening the door for realizing compact devices such as Faraday rotators, isolators and circulators. In this paper, an accurate and analytical method is proposed for a periodic array of graphene ribbons under magnetic bias. The method is based on integral equations governing the induced surface currents on the coplana… ▽ More A sheet of graphene under magnetic bias attains anisotropic surface conductivity, opening the door for realizing compact devices such as Faraday rotators, isolators and circulators. In this paper, an accurate and analytical method is proposed for a periodic array of graphene ribbons under magnetic bias. The method is based on integral equations governing the induced surface currents on the coplanar array of graphene ribbons. For subwavelength size ribbons subjected to normally incident plane waves, the current distribution is derived leading to analytical expressions for the reflection/transmission coefficients. The results obtained are in excellent agreement with full-wave simulations and predict resonant spectral effects that cannot be accounted for by existing semi-analytical methods. Finally, we extract an analytical, closed form solution for the Faraday rotation of magnetically-biased graphene ribbons. In contrast to previous studies, this paper presents a fast, precise and reliable technique for analyzing magnetically-biased array of graphene ribbons, which are one of the most popular graphene-based structures. △ Less

Submitted 13 August, 2019; originally announced August 2019.

Electromagnetic Field Tapering in the High-Roughness Substrates Coated by a Thin Film of Manganese: A Lithography-Free Approach to Ultra-Broadband, Wide-Angle, UV to FIR Perfect Absorption

Authors: Majid Aalizadeh, Mohammad Reza Tavakol, Amin Khavasi, Mehmet Yilmaz, Ekmel Ozbay

Abstract: Metallic layers are known to be used for the suppression of wave transmission when their thickness is sufficiently higher than the skin depth of metal. If in addition to blocking the transmission, metallic layers have the feature of blocking the reflection, too, they would make perfect absorbers. In this work, we propose an experimental approach of using a single thin layer of Manganese (Mn) as bo… ▽ More Metallic layers are known to be used for the suppression of wave transmission when their thickness is sufficiently higher than the skin depth of metal. If in addition to blocking the transmission, metallic layers have the feature of blocking the reflection, too, they would make perfect absorbers. In this work, we propose an experimental approach of using a single thin layer of Manganese (Mn) as both the transmission suppresser and the reflection suppresser. This approach leads to obtaining lithography-free ultra-broadband perfect absorption in an ultra-wide spectrum ranging from Ultraviolet (UV) to Far Infrared (FIR). The measured average absorption is approximately 99%. Such a promising result can be achieved by only coating a single Mn layer on high-roughness substrates that include random nano-pyramids on it. In other words, we do not need a stack of different materials and combinations of geometrical features. The high roughness is realized on a commercial Silicon wafer substrate by inductively coupled plasma (ICP) etching. The key to this ultra-wideband absorption is electromagnetic field tapering which exists due to the graded-index feature of the structure (known as moth-eye effect), along with the ideal optical properties of Mn which makes it an excellent metal for broadband absorption applications. A full experimental characterization of the fabricated samples is presented along with the physical analysis of the phenomena. The findings of this paper can be used for the realization of lithography-free, cost-effective and high-throughput mass production of broadband absorbers. △ Less

Submitted 7 March, 2019; v1 submitted 5 December, 2018; originally announced December 2018.

Comments: 15 pages, 7 figures

Designing Dual-Band Absorbers by Graphene/Metallic Metasurfaces

Authors: Saeedeh Barzegar-Parizi, Amin Khavasi

Abstract: This article presents a novel approach for designing dual-band absorbers based on graphene and metallic metasurfaces for terahertz and mid-infrared regimes, respectively. The absorbers are composed of a two-dimensional (2D) array of square patches deposited on a dielectric film terminated by a metal plate. Using an analytical circuit model, we obtain closed-form relations for different parameters… ▽ More This article presents a novel approach for designing dual-band absorbers based on graphene and metallic metasurfaces for terahertz and mid-infrared regimes, respectively. The absorbers are composed of a two-dimensional (2D) array of square patches deposited on a dielectric film terminated by a metal plate. Using an analytical circuit model, we obtain closed-form relations for different parameters of the structure to achieve the dual-band absorber. Two absorption bands with obtained absorptivity of 98% at 0.55 and 1.54 THz for the graphene-based structure and 7 and 25 THz for the metallic-based case are achieved. We demonstrate that the graphene-based absorber remains as dual-band for a wide range of the Fermi level. Furthermore, the proposed dual-band absorbers have a polarization-insensitive characteristic remaining over a wide range of incident angles. The most important advantage of this device is its simplicity compared to previously reported structures. △ Less

Submitted 25 February, 2019; v1 submitted 3 November, 2018; originally announced November 2018.

A Route to Unusually Broadband Absorption Spanning from Visible to Mid-Infrared

Authors: Majid Aalizadeh, Amin Khavasi, Andriy E. Serebryannikov, Guy A. E. Vandenbosch, Ekmel Ozbay

Abstract: In this paper, a route to ultra-broadband absorption is suggested and demonstrated by a feasible design. The high absorption regime (absorption above 90%) for the suggested structure ranges from visible to mid-infrared (MIR), i.e. for the wavelength from 478 to 3,278 nm that yields an ultra-wide bandwidth of 2,800 nm. The structure consists of a top-layer-patterned metal-insulator-metal (MIM) conf… ▽ More In this paper, a route to ultra-broadband absorption is suggested and demonstrated by a feasible design. The high absorption regime (absorption above 90%) for the suggested structure ranges from visible to mid-infrared (MIR), i.e. for the wavelength from 478 to 3,278 nm that yields an ultra-wide bandwidth of 2,800 nm. The structure consists of a top-layer-patterned metal-insulator-metal (MIM) configuration, into the insulator layer of which, an ultra-thin 5 nm layer of Manganese (Mn) is embedded. The MIM configuration represents a Ti-Al2O3-Ti tri-layer. It is shown that, without the ultra-thin layer of Mn, the absorption bandwidth is reduced to 274 nm. Therefore, adding only a 5 nm layer of Mn leads to a more than tenfold increase in the width of the absorption band. It is explained in detail that the physical mechanism contributing to this ultra-broadband result is a combination of plasmonic and non-plasmonic resonance modes, along with the appropriate optical properties of Mn. This structure has the relative bandwidth (RBW) of 149%, while only one step of lithography is required for its fabrication, so it is relatively simple to fabricate. This makes it rather promising for practical applications. △ Less

Submitted 16 October, 2018; originally announced October 2018.

Comments: 17 pages, 12 figures

Lithography-Free, Manganese-Based Ultra-Broadband Absorption Through Annealing-Based Deformation of Thin Layers into metal-air composites

Authors: Majid Aalizadeh, Amin Khavasi, Bayram Butun, Ekmel Ozbay

Abstract: Fabrication, characterization, and analysis of an ultra-broadband lithography-free absorber is presented. An over 94% average absorption is experimentally achieved in the wavelength range of 450-1400 nm. This ultra-broadband absorption is obtained by a simple annealed tri-layer metal-insulator-metal (MIM) configuration. The metal used in the structure is Manganese (Mn), which also makes the struct… ▽ More Fabrication, characterization, and analysis of an ultra-broadband lithography-free absorber is presented. An over 94% average absorption is experimentally achieved in the wavelength range of 450-1400 nm. This ultra-broadband absorption is obtained by a simple annealed tri-layer metal-insulator-metal (MIM) configuration. The metal used in the structure is Manganese (Mn), which also makes the structure cost-effective. It is shown that the structure retains its high absorption for TM polarization, up to 70 degrees, and, for TE polarization, up to 50 degrees. Moreover, the physical mechanism behind this broadband absorption is explained. Being both lithography-free and cost-effective, the structure is a perfect candidate for large-area and mass production purposes. △ Less

Submitted 21 December, 2018; v1 submitted 16 October, 2018; originally announced October 2018.

Comments: 8 pages, 3 figures

Wideband Antireflection Coating Using Metamaterials

Authors: Fahimeh Sepehripour, Parisa Karimi, Amin Khavasi

Abstract: In this paper, we propose a new approach for realizing antireflection coating using metamaterials. In this approach, a subwavelength array of metallic pillars (with square cross-section) is used for implementing antireflection coating. The effective impedance of the array can be duly adjusted by the size and distance of pillars. Therefore, we design the effective impedance of the antireflection co… ▽ More In this paper, we propose a new approach for realizing antireflection coating using metamaterials. In this approach, a subwavelength array of metallic pillars (with square cross-section) is used for implementing antireflection coating. The effective impedance of the array can be duly adjusted by the size and distance of pillars. Therefore, we design the effective impedance of the antireflection coating to be the geometrical mean of the upper and lower mediums impedance and we choose its height to be a quarter of operating wavelength. Consequently, the reflection vanishes at the desired frequency and fractional bandwidth of 56% is achieved with a criterion of 10% reflectance (the refractive index of the substrate is assumed to be 4). The proposed structure is symmetric in both directions. So, it is not sensitive to the polarization of the incident wave at normal incidence. Furthermore, we show that using the multilayer Chebyshev matching transformer of transmission line theory increases the bandwidth of the antireflection up to 107% at the expense of pass-band ripples. This structure can be used from very low frequencies up to infrared regime by appropriate scaling. △ Less

Submitted 2 February, 2019; v1 submitted 27 August, 2018; originally announced August 2018.

Temporal Analog Optical Computing using an On-Chip Fully Reconfigurable Photonic Signal Processor

Authors: Hossein Babashah, Zahra Kavehvash, Amin Khavasi, Somayyeh Koohi

Abstract: This paper introduces the concept of on-chip temporal optical computing, based on dispersive Fourier transform and suitably designed modulation module, to perform mathematical operations of interest, such as differentiation, integration, or convolution in time domain. The desired mathematical operation is performed as signal propagates through a fully reconfigurable on-chip photonic signal process… ▽ More This paper introduces the concept of on-chip temporal optical computing, based on dispersive Fourier transform and suitably designed modulation module, to perform mathematical operations of interest, such as differentiation, integration, or convolution in time domain. The desired mathematical operation is performed as signal propagates through a fully reconfigurable on-chip photonic signal processor. Although a few number of photonic temporal signal processors have been introduced recently, they are usually bulky or they suffer from limited reconfigurability which is of great importance to implement large-scale general-purpose photonic signal processors. To address these limitations, this paper demonstrates a fully reconfigurable photonic integrated signal processing system. As the key point, the reconfigurability is achieved by taking advantages of dispersive Fourier transformation, linearly chirp modulation using four wave mixing, and applying the desired arbitrary transfer function through a cascaded Mach-Zehnder modulator and phase modulator. Our demonstration reveals an operation time of $200~ps$ with high resolution of $300~fs$. To have an on-chip photonic signal processor, a broadband photonic crystal waveguide with an extremely large group-velocity dispersion of $2.81 \times {10^{6}}~\frac{ps^2}{km}$ is utilized. Numerical simulations of the proposed structure reveal a great potential for chip-scale fully reconfigurable all-optical signal processing through a bandwidth of $400~GHz$. △ Less

Submitted 18 December, 2017; originally announced December 2017.

Two Dimensional Edge Detection by Guided Mode Resonant Metasurface

Authors: Amirhossein Saba, Mohammad Reza Tavakol, Parisa Karimi-Khoozani, Amin Khavasi

Abstract: In this letter, a new approach to perform edge detection is presented using an all-dielectric CMOS-compatible metasurface. The design is based on guided-mode resonance which provides a high quality factor resonance to make the edge detection experimentally realizable. The proposed structure that is easy to fabricate, can be exploited for detection of edges in two dimensions due to its symmetry. Al… ▽ More In this letter, a new approach to perform edge detection is presented using an all-dielectric CMOS-compatible metasurface. The design is based on guided-mode resonance which provides a high quality factor resonance to make the edge detection experimentally realizable. The proposed structure that is easy to fabricate, can be exploited for detection of edges in two dimensions due to its symmetry. Also, the trade-off between gain and resolution of edge detection is discussed which can be adjusted by appropriate design parameters. The proposed edge detector has also the potential to be used in ultrafast analog computing and image processing. △ Less

Submitted 18 November, 2017; v1 submitted 5 November, 2017; originally announced November 2017.

Spatial Integration by a Dielectric Slab Waveguide and its Planar Graphene-based Counterpart

Authors: Farzad Zangeneh-Nejad, Amin Khavasi

Abstract: Motivated by the recent progress in analog computing [Science 343, 160 (2014)], a new approach to perform spatial integration is presented using a dielectric slab waveguide. Our approach is indeed based on the fact that the transmission coefficient of a simple dielectric slab waveguide at its mode excitation angle matches the Green's function of first order integration. Inspired by the mentioned d… ▽ More Motivated by the recent progress in analog computing [Science 343, 160 (2014)], a new approach to perform spatial integration is presented using a dielectric slab waveguide. Our approach is indeed based on the fact that the transmission coefficient of a simple dielectric slab waveguide at its mode excitation angle matches the Green's function of first order integration. Inspired by the mentioned dielectric-based integrator, we further demonstrate its graphene-based counterpart. The latter is not only reconfigurable but also highly miniaturized in contrast to the previously reported designs [Opt. Commun. 338, 457 (2015)]. Such integrators have the potential to be used in ultrafast analog computation and signal processing. △ Less

Submitted 8 March, 2017; originally announced March 2017.

Accurate Effective Medium Theory for the Analysis of Spoof Localized Surface Plasmons in Textured Metallic Cylinders

Authors: Babak Rahmani, Amirmasood Bagheri, Amin Khavasi

Abstract: It has been recently demonstrated that textured closed surfaces which are made out of perfect electric conductors (PECs) can mimic highly localized surface plasmons (LSPs). Here, we propose an effective medium which can accurately model LSP resonances in a two-dimensional periodically decorated PEC cylinder. The accuracy of previous models is limited to structures with deep-subwavelength and high… ▽ More It has been recently demonstrated that textured closed surfaces which are made out of perfect electric conductors (PECs) can mimic highly localized surface plasmons (LSPs). Here, we propose an effective medium which can accurately model LSP resonances in a two-dimensional periodically decorated PEC cylinder. The accuracy of previous models is limited to structures with deep-subwavelength and high number of grooves. However, we show that our model can successfully predict the ultra-sharp LSP resonances which exist in structures with relatively lower number of grooves. Such resonances are not correctly predictable with previous models that give some spurious resonances. The success of the proposed model is indebted to the incorporation of an effective surface conductivity which is created at the interface of the cylinder and the homogeneous medium surrounding the structure. This surface conductivity models the effect of higher diffracted orders which are excited in the periodic structure. The validity of the proposed model is verified by full-wave simulations. △ Less

Submitted 15 January, 2017; originally announced January 2017.

Analog Optical Computing by Half-Wavelength Slabs

Authors: Farzad Zangeneh-Nejad, Amin Khavasi, Behzad Rejaei

Abstract: A new approach to perform analog optical differentiation is presented using half-wavelength slabs. First, a half-wavelength dielectric slab is used to design a first order differentiator. The latter works properly for both major polarizations, in contrast to designs based on Brewster effect [Opt. Lett. 41, 3467 (2016)]. Inspired by the proposed dielectric differentiator, and by exploiting the uniq… ▽ More A new approach to perform analog optical differentiation is presented using half-wavelength slabs. First, a half-wavelength dielectric slab is used to design a first order differentiator. The latter works properly for both major polarizations, in contrast to designs based on Brewster effect [Opt. Lett. 41, 3467 (2016)]. Inspired by the proposed dielectric differentiator, and by exploiting the unique features of graphene, we further design and demonstrate a reconfigurable and highly miniaturized differentiator using a half-wavelength plasmonic graphene film. To the best of our knowledge, our proposed graphene-based differentiator is even smaller than the most compact differentiator presented so far [Opt. Lett. 40, 5239 (2015)]. △ Less

Submitted 10 January, 2017; originally announced January 2017.

Effect of Graphene on the Absorption and Extraordinary Transmission of Light in One Dimensional Metallic Gratings

Authors: Amirmasood Bagheri, Babak Rahmani, Amin Khavasi

Abstract: Periodic metallic structures are known to support resonant extraordinary transmission (EOT). When covered with graphene, these structures can be employed to effectively manipulate the light. In this work, we propose an analytical circuit model for graphene-covered one-dimensional metallic gratings. By using the circuit theory, we demonstrate that one-dimensional periodic array of cut-through slits… ▽ More Periodic metallic structures are known to support resonant extraordinary transmission (EOT). When covered with graphene, these structures can be employed to effectively manipulate the light. In this work, we propose an analytical circuit model for graphene-covered one-dimensional metallic gratings. By using the circuit theory, we demonstrate that one-dimensional periodic array of cut-through slits which are covered by a continuous graphene sheet exhibit tunable EOT resonance whose amplitude, unlike its spectral position, can be dynamically tuned by varying the Fermi level of graphene. In this fashion, it is shown that placing a perfect reflector at the bottom of the graphene-covered metallic grating results in the realization of a graphene-based absorber. By utilizing the circuit theory, it is illustrated that perfect absorption in the structure is not exclusive to the TM polarization, but also the TE polarized plane waves can be completely absorbed by duly adjusting the Fermi level of graphene. Criteria for the enhanced absorption are accordingly presented. Results of this work may provide a useful tool for designing novel devices based on the graphene-covered metallic gratings such as filters, modulators and efficient absorbers. △ Less

Submitted 23 December, 2016; originally announced December 2016.

Dynamics of magnetic nano-flake vortices in Newtonian fluids

Authors: Nasim Bazazzadeh, Seyed Majid Mohseni, Amin Khavasi, Mohammad Ismail Zibaii, S. M. S. Movahed, Gholam Reza Jafari

Abstract: We study the rotational motion of nano-flake ferromagnetic discs suspended in a Newtonian fluid, as a potential material owing the vortex-like magnetic configuration. Using analytical expressions for hydrodynamic, magnetic and Brownian torques, the stochastic angular momentum equation is determined in the dilute limit conditions under applied magnetic field. Results are compared against experiment… ▽ More We study the rotational motion of nano-flake ferromagnetic discs suspended in a Newtonian fluid, as a potential material owing the vortex-like magnetic configuration. Using analytical expressions for hydrodynamic, magnetic and Brownian torques, the stochastic angular momentum equation is determined in the dilute limit conditions under applied magnetic field. Results are compared against experimental ones and excellent agreement is observed. We also estimate the uncertainty in the orientation of the discs due to the Brownian torque when an external magnetic field aligns them. Interestingly, this uncertainty is roughly proportional to the ratio of thermal energy of fluid to the magnetic energy stored in the discs. Our approach can be implemented in many practical applications including biotechnology and multi-functional fluidics. △ Less

Submitted 23 November, 2016; originally announced November 2016.

Comments: 13 pages, 7 figures

Journal ref: Journal of Magnetism and Magnetic Materials 419 (2016) 547-552

Broadband, Polarization-insensitive and Wide-angle Optical Absorber based on Fractal Plasmonics

Authors: Ali Eshaghian, Sajjad AbdollahRamezani, Ata Chizari, Amin Khavasi

Abstract: In this paper, a plasmonic absorber consisting of a metal-dielectric-metal stack with a top layer of Sierpinski nanocarpet is theoretically investigated. Such compact absorber depicts broadband angle-independent behavior over a wide optical wavelength range ($400-700$ nm) and a broad range of angles of light incidence ($0-80^{\circ}$). Including several feature sizes, such fractal-like structure s… ▽ More In this paper, a plasmonic absorber consisting of a metal-dielectric-metal stack with a top layer of Sierpinski nanocarpet is theoretically investigated. Such compact absorber depicts broadband angle-independent behavior over a wide optical wavelength range ($400-700$ nm) and a broad range of angles of light incidence ($0-80^{\circ}$). Including several feature sizes, such fractal-like structure shows widely strong extinction ($85-99$%) response for either transverse electric or magnetic polarization states under normal incidence. Underlying mechanisms of absorbance due to excited surface plasmon modes as well as electric/magnetic dipole resonances are well revealed by investigating electric field, magnetic field and current distributions. The proposed absorber opens a path to realize high-performance ultrathin light trap** devices. △ Less

Submitted 31 May, 2016; v1 submitted 23 May, 2016; originally announced May 2016.

Analog computing by Brewster effect

Authors: Amir Youssefi, Farzad Zangeneh-Nejad, Sajjad AbdollahRamezani, Amin Khavasi

Abstract: Optical computing has emerged as a promising candidate for real-time and parallel continuous data processing. Motivated by recent progresses in metamaterial-based analog computing [Science 343, 160 (2014)], we theoretically investigate realization of two-dimensional complex mathematical operations using rotated configurations, recently reported in [Opt. Lett. 39, 1278 (2014)]. Breaking the reflect… ▽ More Optical computing has emerged as a promising candidate for real-time and parallel continuous data processing. Motivated by recent progresses in metamaterial-based analog computing [Science 343, 160 (2014)], we theoretically investigate realization of two-dimensional complex mathematical operations using rotated configurations, recently reported in [Opt. Lett. 39, 1278 (2014)]. Breaking the reflection symmetry, such configurations could realize both even and odd Green's functions associated with spatial operators. Based on such appealing theory and by using Brewster effect, we demonstrate realization of a first-order differentiator. Such efficient wave-based computation method not only circumvents the major potential drawbacks of metamaterials, but also offers the most compact possible device compared to the conventional bulky lens-based optical signal and data processors. △ Less

Submitted 30 June, 2016; v1 submitted 25 April, 2016; originally announced April 2016.

Comments: 4 pages, 7 figures, journal

Significant crosstalk reduction using all-dielectric CMOS-compatible metamaterials

Authors: Amin Khavasi, Lukas Chrostowski, Zeqin Lu, Richard Bojko

Abstract: A recent computational result suggests that highly confined modes can be realized by all-dielectric metamaterials (S. Jahani et. al., Optica 1, 96 (2014)). This substantially decreases crosstalk between dielectric waveguides, paving the way for high-density photonic circuits. Here, we experimentally demonstrate, on a standard silicon-on-insulator (SOI) platform, that using a simple metamaterial be… ▽ More A recent computational result suggests that highly confined modes can be realized by all-dielectric metamaterials (S. Jahani et. al., Optica 1, 96 (2014)). This substantially decreases crosstalk between dielectric waveguides, paving the way for high-density photonic circuits. Here, we experimentally demonstrate, on a standard silicon-on-insulator (SOI) platform, that using a simple metamaterial between two silicon strip waveguides results in about a 10-fold increase in coupling length. The proposed structure may lead to significant reduction in the size of devices in silicon photonics. △ Less

Submitted 11 November, 2016; v1 submitted 19 February, 2016; originally announced February 2016.

Analog Computing Using Graphene-based Metalines

Authors: Sajjad AbdollahRamezani, Kamalodin Arik, Amin Khavasi, Zahra Kavehvash

Abstract: We introduce the new concept of "metalines" for manipulating the amplitude and phase profile of an incident wave locally and independently. Thanks to the highly confined graphene plasmons, a transmit-array of graphene-based metalines is used to realize analog computing on an ultra-compact, integrable and planar platform. By employing the general concepts of spatial Fourier transformation, a well-d… ▽ More We introduce the new concept of "metalines" for manipulating the amplitude and phase profile of an incident wave locally and independently. Thanks to the highly confined graphene plasmons, a transmit-array of graphene-based metalines is used to realize analog computing on an ultra-compact, integrable and planar platform. By employing the general concepts of spatial Fourier transformation, a well-designed structure of such meta-transmit-array combined with graded index lenses can perform two mathematical operations; i.e. differentiation and integration, with high efficiency. The presented configuration is about 60 times shorter than the recent structure proposed by Silva et al.(Science, 2014, 343, 160-163); moreover, our simulated output responses are in more agreement with the desired analytic results. These findings may lead to remarkable achievements in light-based plasmonic signal processors at nanoscale instead of their bulky conventional dielectric lens-based counterparts. △ Less

Submitted 2 September, 2015; originally announced September 2015.

Utility Max-Min Fair Link Adaptation in IEEE 802.11ac Downlink Multi-User

Authors: Ali A. Khavasi, Mojtaba Aajami, Hae-Ryeon Park, Jung-Bong Suk

Abstract: In this letter, we propose a novel model and corresponding algorithms to address the optimal utility max-min fair link adaptation in Downlink Multi-User (DL-MU) feature of the emerging IEEE 802.11ac WLAN standard. Herein, we first propose a simple yet accurate model to formulate the max-min fair link adaptation problem. Furthermore, this model guarantees the minimum utility gain of each receiver a… ▽ More In this letter, we propose a novel model and corresponding algorithms to address the optimal utility max-min fair link adaptation in Downlink Multi-User (DL-MU) feature of the emerging IEEE 802.11ac WLAN standard. Herein, we first propose a simple yet accurate model to formulate the max-min fair link adaptation problem. Furthermore, this model guarantees the minimum utility gain of each receiver according to its requirements. In the second step, we show that the optimal solution of the proposed model can be obtained in polynomial time, and then the solution algorithms are proposed and analyzed. The simulation results demonstrate the significant achievement of the proposed utility-aware link adaptation approach in terms of max-min fairness and utility gain compared to utility-oblivious schemes. △ Less

Submitted 24 March, 2014; originally announced March 2014.

Comments: Has been accepted in IEEE Communications Letters