Showing 1–2 of 2 results for author: Iyer, P K

Piezo-resistive pressure sensor based on CVD-grown ZnO nanowires on Polyethylene Tetrathalate substrate

Authors: Manisha Kumari, Rakesh K. Prasad, Manish K. Singh, Parameswar K. Iyer, Dilip K. Singh

Abstract: Recent developments in the domain of electronic materials and devices have attracted the interest of researchers toward flexible and printable electronic components like organic transistors, printable electrodes and sensors. Zinc Oxide (ZnO) nanowires (NWs) possess a number of excellent properties like high mobility, large exciton binding energy and the direct-band gap in addition to large piezoel… ▽ More Recent developments in the domain of electronic materials and devices have attracted the interest of researchers toward flexible and printable electronic components like organic transistors, printable electrodes and sensors. Zinc Oxide (ZnO) nanowires (NWs) possess a number of excellent properties like high mobility, large exciton binding energy and the direct-band gap in addition to large piezoelectric coefficients. Here, we report on flexible piezo-resistive sensor based on Indium tin oxide (ITO)-coated Polyethylene tetrathalate (PET) substrate. The device shows sensitivity in terms of change in resistance from 100 Ω to 2.4 KΩ at an applied potential of 5V upon bending from flat to 95 degrees. The 1-D nanowire flexible device in its flat state shows saturated output current. We observed ten folds enhanced variation as compared to previous reports. Improved sensitivity was observed in our experiments due to fewer defects in CVD-grown NWs as compared to others where hydrothermally grown nanowires were used. The methodology of device fabrication reported here requires less time and enables efficient devices for the realization of flexible and wearable technology. △ Less

Submitted 16 June, 2023; originally announced July 2023.

Comments: 24 pages, 5 figures

Optimization and effect of UV-ozone exposure of electron transport layer on the efficiency of the dye-sensitized solar cells

Authors: Chandan Dawo, Mohammad Adil Afroz, Parameswar Krishnan Iyer, Harsh Chaturvedi

Abstract: The surface states of the active TiO2 layer is crucial while fabricating an efficient solar cell. This work experimentally analyses the effect of exposing TiO2 based electron transport layer (ETL) to the ultraviolet-ozone (UV-O3) and optimizes the exposure time for improving power conversion efficiency (PCE) of fabricated dye-sensitized solar cells (DSSCs). These results demonstrate that the perfo… ▽ More The surface states of the active TiO2 layer is crucial while fabricating an efficient solar cell. This work experimentally analyses the effect of exposing TiO2 based electron transport layer (ETL) to the ultraviolet-ozone (UV-O3) and optimizes the exposure time for improving power conversion efficiency (PCE) of fabricated dye-sensitized solar cells (DSSCs). These results demonstrate that the performance of DSSCs can be improved significantly by UV-O3 exposure of sintered TiO2 photoanode surface, with the duration of exposure being a critical parameter. Fabricated devices show 33.01 % increase in PCE for the optimum exposure. Nevertheless, overexposure of the sample beyond the optimum time decreases the efficiency of the fabricated solar cells. The device with optimum exposure exhibits the highest PCE of 8.34% with short circuit current density (Jsc) of 15.15 mA/cm2, open circuit voltage (Voc) of 756 mV and Fill factor (FF) of 71.10%. This increase in efficiency is attributed to the enhanced crystallization and reduction in the organic contaminants C-C/C-H from 57.90 to 52.40% as shown by the X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), respectively. The XPS result further indicates an increase in oxygen vacancy from 12.40 to 23.40% for O 1s state and from 9.30 to 14.30% for Ti 2p state of Ti3+. Results from the Atomic Force Microscope (AFM) also confirms the minimized surface roughness of 16.36 nm for the optimally exposed TiO2 film, and increase in hydrophilicity leading to improved efficiency of the solar cells which were optimally exposed to UV-O3. △ Less

Submitted 27 February, 2020; originally announced February 2020.