-
Characterisation of plastic scintillator paddles and lightweight MWPCs for the MID subsystem of ALICE 3
Authors:
Ruben Alfaro,
Mauricio Alvarado Hernández,
Gyula Bencédi,
Juan Carlos Cabanillas Noris,
Marco Antonio Díaz Maldonado,
Carlos Duarte Galvan,
Arturo Fernández Téllez,
Gergely Gábor Barnaföldi,
Ádám Gera,
Varlen Grabsky,
Gergő Hamar,
Gerardo Herrera Corral,
Ildefonso León Monzón,
Josué Martínez García,
Mario Iván Martínez Hernandez,
Jesús Eduardo Muñoz Méndez,
Richárd Nagy,
Rafael Ángel Narcio Laveaga,
Antonio Ortiz,
Mario Rodríguez Cahuantzi,
Solangel Rojas Torres,
Timea Szollosova,
Miguel Enrique Patiño Salazar,
Jared Pazarán García,
Hector David Regules Medel
, et al. (7 additional authors not shown)
Abstract:
The ALICE collaboration is proposing a completely new detector, ALICE 3, for operation during the LHC Runs 5 and 6. One of the ALICE~3 subsystems is the Muon IDentifier detector (MID), which has to be optimised to be efficient for the reconstruction of $J/ψ$ at rest (muons down to $p_{\rm T}\approx1.5$ GeV/$c$) for $|η|<1.3$. Given the modest particle flux expected in the MID of a few Hz/cm$^2$, t…
▽ More
The ALICE collaboration is proposing a completely new detector, ALICE 3, for operation during the LHC Runs 5 and 6. One of the ALICE~3 subsystems is the Muon IDentifier detector (MID), which has to be optimised to be efficient for the reconstruction of $J/ψ$ at rest (muons down to $p_{\rm T}\approx1.5$ GeV/$c$) for $|η|<1.3$. Given the modest particle flux expected in the MID of a few Hz/cm$^2$, technologies like plastic scintillator bars ($\approx1$ m length) equipped with wavelength-shifting fibers and silicon photomultiplier readout, and lightweight Multi-Wire Proportional Chambers (MWPCs) are under investigation. To this end, different plastic scintillator paddles and MWPCs were studied at the CERN T10 test beam facility. This paper reports on the performance of the scintillator prototypes tested at different beam momenta (from 0.5 GeV/$c$ up to 6 GeV/$c$) and positions (horizontal, vertical, and angular scans). The MWPCs were tested at different momenta (from 0.5 GeV/$c$ to 10 GeV/$c$) and beam intensities, their efficiency and position resolutions were verified beyond the particle rates expected with the MID in ALICE 3.
△ Less
Submitted 16 February, 2024; v1 submitted 9 January, 2024;
originally announced January 2024.
-
Recent Progress and Next Steps for the MATHUSLA LLP Detector
Authors:
Cristiano Alpigiani,
Juan Carlos Arteaga-Velázquez,
Austin Ball,
Liron Barak,
Jared Barron,
Brian Batell,
James Beacham,
Yan Benhammo,
Benjamin Brau,
Karen Salomé Caballero-Mora,
Paolo Camarri,
Roberto Cardarelli,
John Paul Chou,
Wentao Cui,
David Curtin,
Miriam Diamond,
Keith R. Dienes,
Liam Andrew Dougherty,
William Dougherty,
Marco Drewes,
Sameer Erramilli,
Rouven Essig,
Erez Etzion,
Jared Evans,
Arturo Fernández Téllez
, et al. (71 additional authors not shown)
Abstract:
We report on recent progress and next steps in the design of the proposed MATHUSLA Long Lived Particle (LLP) detector for the HL-LHC as part of the Snowmass 2021 process. Our understanding of backgrounds has greatly improved, aided by detailed simulation studies, and significant R&D has been performed on designing the scintillator detectors and understanding their performance. The collaboration is…
▽ More
We report on recent progress and next steps in the design of the proposed MATHUSLA Long Lived Particle (LLP) detector for the HL-LHC as part of the Snowmass 2021 process. Our understanding of backgrounds has greatly improved, aided by detailed simulation studies, and significant R&D has been performed on designing the scintillator detectors and understanding their performance. The collaboration is on track to complete a Technical Design Report, and there are many opportunities for interested new members to contribute towards the goal of designing and constructing MATHUSLA in time for HL-LHC collisions, which would increase the sensitivity to a large variety of highly motivated LLP signals by orders of magnitude.
△ Less
Submitted 30 March, 2023; v1 submitted 15 March, 2022;
originally announced March 2022.
-
An Update to the Letter of Intent for MATHUSLA: Search for Long-Lived Particles at the HL-LHC
Authors:
Cristiano Alpigiani,
Juan Carlos Arteaga-Velázquez,
Austin Ball,
Liron Barak,
Jared Barron,
Brian Batell,
James Beacham,
Yan Benhammo,
Karen Salomé Caballero-Mora,
Paolo Camarri,
Roberto Cardarelli,
John Paul Chou,
Wentao Cui,
David Curtin,
Miriam Diamond,
Keith R. Dienes,
Liam Andrew Dougherty,
Giuseppe Di Sciascio,
Marco Drewes,
Erez Etzion,
Rouven Essig,
Jared Evans,
Arturo Fernández Téllez,
Oliver Fischer,
Jim Freeman
, et al. (58 additional authors not shown)
Abstract:
We report on recent progress in the design of the proposed MATHUSLA Long Lived Particle (LLP) detector for the HL-LHC, updating the information in the original Letter of Intent (LoI), see CDS:LHCC-I-031, arXiv:1811.00927. A suitable site has been identified at LHC Point 5 that is closer to the CMS Interaction Point (IP) than assumed in the LoI. The decay volume has been increased from 20 m to 25 m…
▽ More
We report on recent progress in the design of the proposed MATHUSLA Long Lived Particle (LLP) detector for the HL-LHC, updating the information in the original Letter of Intent (LoI), see CDS:LHCC-I-031, arXiv:1811.00927. A suitable site has been identified at LHC Point 5 that is closer to the CMS Interaction Point (IP) than assumed in the LoI. The decay volume has been increased from 20 m to 25 m in height. Engineering studies have been made in order to locate much of the decay volume below ground, bringing the detector even closer to the IP. With these changes, a 100 m x 100 m detector has the same physics reach for large c$τ$ as the 200 m x 200 m detector described in the LoI and other studies. The performance for small c$τ$ is improved because of the proximity to the IP. Detector technology has also evolved while retaining the strip-like sensor geometry in Resistive Plate Chambers (RPC) described in the LoI. The present design uses extruded scintillator bars read out using wavelength shifting fibers and silicon photomultipliers (SiPM). Operations will be simpler and more robust with much lower operating voltages and without the use of greenhouse gases. Manufacturing is straightforward and should result in cost savings. Understanding of backgrounds has also significantly advanced, thanks to new simulation studies and measurements taken at the MATHUSLA test stand operating above ATLAS in 2018. We discuss next steps for the MATHUSLA collaboration, and identify areas where new members can make particularly important contributions.
△ Less
Submitted 3 September, 2020;
originally announced September 2020.
-
Performance of ALICE AD modules in the CERN PS test beam
Authors:
M. Broz,
J. C. Cabanillas Noris,
E. Calvo Villar,
C. Duarte Galvan,
E. Endress,
L. G. Espinoza Beltran,
A. Fernandez Tellez,
D. Finogeev,
A. M. Gago,
G. Herrera Corral,
T. Kim,
A. Kurepin,
A. B. Kurepin,
N. Kurepin,
I. Leon Monzon,
M. I. Martinez Hernandez,
C. Mayer,
M. M. Mieskolainen,
R. Orava,
L. A. Perez Moreno,
J. -P. Revol,
M. Rodriguez Cahuantzi,
S. Rojas Torres,
D. Serebryakov,
A. Shabanov
, et al. (2 additional authors not shown)
Abstract:
Two modules of the AD detector have been studied with the test beam at the T10 facility at CERN. The AD detector is made of scintillator pads read out by wave-length shifters (WLS)coupled to clean fibres that carry the produced light to photo-multiplier tubes (PMTs). In ALICE the AD is used to trigger and study the physics of diffractive and ultra-peripheral collisions as well as for a variety of…
▽ More
Two modules of the AD detector have been studied with the test beam at the T10 facility at CERN. The AD detector is made of scintillator pads read out by wave-length shifters (WLS)coupled to clean fibres that carry the produced light to photo-multiplier tubes (PMTs). In ALICE the AD is used to trigger and study the physics of diffractive and ultra-peripheral collisions as well as for a variety of technical tasks like beam-gas background monitoring or as a luminometer. The position dependence of the modules' efficiency has been measured and the effect of hits on the WLS or PMTs has been evaluated. The charge deposited by pions and protons has been measured at different momenta of the test beam. The time resolution is determined as a function of the deposited charge. These results are important ingredients to better understand the AD detector, to benchmark the corresponding simulations, and very importantly they served as a baseline for a similar device, the Forward Diffractive Detector (FDD), being currently built and that will be in operation in ALICE during the LHC Runs 3 and 4.
△ Less
Submitted 26 June, 2020;
originally announced June 2020.
-
MATHUSLA: A Detector Proposal to Explore the Lifetime Frontier at the HL-LHC
Authors:
Henry Lubatti,
Cristiano Alpigiani,
Juan Carlos Arteaga-Velázquez,
Austin Ball,
Liron Barak James Beacham,
Yan Benhammo,
Karen Salomé Caballero-Mora,
Paolo Camarri,
Tingting Cao,
Roberto Cardarelli,
John Paul Chou,
David Curtin,
Albert de Roeck,
Giuseppe Di Sciascio,
Miriam Diamond,
Marco Drewes,
Sarah C. Eno,
Rouven Essig,
Jared Evans,
Erez Etzion,
Arturo Fernández Téllez,
Oliver Fischer,
Jim Freeman,
Stefano Giagu,
Brandon Gomes
, et al. (38 additional authors not shown)
Abstract:
The observation of long-lived particles at the LHC would reveal physics beyond the Standard Model, could account for the many open issues in our understanding of our universe, and conceivably point to a more complete theory of the fundamental interactions. Such long-lived particle signatures are fundamentally motivated and can appear in virtually every theoretical construct that address the Hierar…
▽ More
The observation of long-lived particles at the LHC would reveal physics beyond the Standard Model, could account for the many open issues in our understanding of our universe, and conceivably point to a more complete theory of the fundamental interactions. Such long-lived particle signatures are fundamentally motivated and can appear in virtually every theoretical construct that address the Hierarchy Problem, Dark Matter, Neutrino Masses and the Baryon Asymmetry of the Universe. We describe in this document a large detector, MATHUSLA, located on the surface above an HL-LHC $pp$ interaction point, that could observe long-lived particles with lifetimes up to the Big Bang Nucleosynthesis limit of 0.1 s. We also note that its large detector area allows MATHUSLA to make important contributions to cosmic ray physics. Because of the potential for making a major breakthrough in our conceptual understanding of the universe, long-lived particle searches should have the highest level of priority.
△ Less
Submitted 13 January, 2019;
originally announced January 2019.
-
A Letter of Intent for MATHUSLA: a dedicated displaced vertex detector above ATLAS or CMS
Authors:
Cristiano Alpigiani,
Austin Ball,
Liron Barak,
James Beacham,
Yan Benhammo,
Tingting Cao,
Paolo Camarri,
Roberto Cardarelli,
Mario Rodriguez-Cahuantzi,
John Paul Chou,
David Curtin,
Miriam Diamond,
Giuseppe Di Sciascio,
Marco Drewes,
Sarah C. Eno,
Erez Etzion,
Rouven Essig,
Jared Evans,
Oliver Fischer,
Stefano Giagu,
Brandon Gomes,
Andy Haas,
Yuekun Heng,
Giuseppe Iaselli,
Ken Johns
, et al. (39 additional authors not shown)
Abstract:
In this Letter of Intent (LOI) we propose the construction of MATHUSLA (MAssive Timing Hodoscope for Ultra-Stable neutraL pArticles), a dedicated large-volume displaced vertex detector for the HL-LHC on the surface above ATLAS or CMS. Such a detector, which can be built using existing technologies with a reasonable budget in time for the HL-LHC upgrade, could search for neutral long-lived particle…
▽ More
In this Letter of Intent (LOI) we propose the construction of MATHUSLA (MAssive Timing Hodoscope for Ultra-Stable neutraL pArticles), a dedicated large-volume displaced vertex detector for the HL-LHC on the surface above ATLAS or CMS. Such a detector, which can be built using existing technologies with a reasonable budget in time for the HL-LHC upgrade, could search for neutral long-lived particles (LLPs) with up to several orders of magnitude better sensitivity than ATLAS or CMS, while also acting as a cutting-edge cosmic ray telescope at CERN to explore many open questions in cosmic ray and astro-particle physics. We review the physics motivations for MATHUSLA and summarize its LLP reach for several different possible detector geometries, as well as outline the cosmic ray physics program. We present several updated background studies for MATHUSLA, which help inform a first detector-design concept utilizing modular construction with Resistive Plate Chambers (RPCs) as the primary tracking technology. We present first efficiency and reconstruction studies to verify the viability of this design concept, and we explore some aspects of its total cost. We end with a summary of recent progress made on the MATHUSLA test stand, a small-scale demonstrator experiment currently taking data at CERN Point 1, and finish with a short comment on future work.
△ Less
Submitted 2 November, 2018;
originally announced November 2018.
-
LHC Forward Physics
Authors:
K. Akiba,
M. Akbiyik,
M. Albrow,
M. Arneodo,
V. Avati,
J. Baechler,
O. Villalobos Baillie,
P. Bartalini,
J. Bartels,
S. Baur,
C. Baus,
W. Beaumont,
U. Behrens,
D. Berge,
M. Berretti,
E. Bossini,
R. Boussarie,
S. Brodsky,
M. Broz,
M. Bruschi,
P. Bussey,
W. Byczynski,
J. C. Cabanillas Noris,
E. Calvo Villar,
A. Campbell
, et al. (162 additional authors not shown)
Abstract:
The goal of this report is to give a comprehensive overview of the rich field of forward physics, with a special attention to the topics that can be studied at the LHC. The report starts presenting a selection of the Monte Carlo simulation tools currently available, chapter 2, then enters the rich phenomenology of QCD at low, chapter 3, and high, chapter 4, momentum transfer, while the unique scat…
▽ More
The goal of this report is to give a comprehensive overview of the rich field of forward physics, with a special attention to the topics that can be studied at the LHC. The report starts presenting a selection of the Monte Carlo simulation tools currently available, chapter 2, then enters the rich phenomenology of QCD at low, chapter 3, and high, chapter 4, momentum transfer, while the unique scattering conditions of central exclusive production are analyzed in chapter 5. The last two experimental topics, Cosmic Ray and Heavy Ion physics are presented in the chapter 6 and 7 respectively. Chapter 8 is dedicated to the BFKL dynamics, multiparton interactions, and saturation. The report ends with an overview of the forward detectors at LHC. Each chapter is correlated with a comprehensive bibliography, attempting to provide to the interested reader with a wide opportunity for further studies.
△ Less
Submitted 9 December, 2017; v1 submitted 15 November, 2016;
originally announced November 2016.
