-
Optimizing the architecture for coherent beat note acquisition in LISA
Authors:
Philipp Euringer,
Gerald Hechenblaikner,
Alexander Sell,
Francis Soualle,
Walter Fichter
Abstract:
The laser interferometer space antenna (LISA) senses gravitational waves by measuring distance fluctuations between three spacecraft (SC). These measurements rely on precise tracking of a beat note phase that is formed on a quadrant-photo-diode (QPD) at each SC by interference of a local laser with a laser sent from a distant SC. The crucial prerequisite of the phase tracking is a successful acqui…
▽ More
The laser interferometer space antenna (LISA) senses gravitational waves by measuring distance fluctuations between three spacecraft (SC). These measurements rely on precise tracking of a beat note phase that is formed on a quadrant-photo-diode (QPD) at each SC by interference of a local laser with a laser sent from a distant SC. The crucial prerequisite of the phase tracking is a successful acquisition of the beat note frequency. This article aims to optimize the carrier-to-noise density ratio (CNR) during this process, and to evaluate the resulting probability of detection (PD). CNR is generally lowest during the beat note acquisition process since pointing accuracy relies on coarse acquisition techniques. Based on analytical models, we examine which combinations of QPD segments for the signal read-out yield the highest CNR, i.e., they are least susceptible to pointing errors. We find from simulations that the highest CNR is ensured by taking the maximum of a combination of two segments in vertical and horizontal direction. For pointing errors (3$σ$) of 3.9 $μ$rad and 4.3 $μ$rad this yields an improvement of around 3.7 dB and 5.6 dB in CNR, respectively, in comparison to a combination of all four segments. In addition, the PD for various configurations of the baselined Fourier peak detection is analyzed. Here we find that the PD is most sensitive to the CNR compared to the design parameters of the acquisition scheme, in particular the FFT length. Moreover, it is shown that aforementioned improvements in CNR can lead to a significant enhancement of the PD.
△ Less
Submitted 27 June, 2024;
originally announced June 2024.
-
Time-delay interferometry with onboard optical delays
Authors:
Jan Niklas Reinhardt,
Philipp Euringer,
Olaf Hartwig,
Gerald Hechenblaikner,
Gerhard Heinzel,
Kohei Yamamoto
Abstract:
Time-delay interferometry (TDI) is a data processing technique for space-based gravitational-wave detectors to create laser-noise-free equal-optical-path-length interferometers virtually on the ground. It relies on the interspacecraft signal propagation delays, which are delivered by intersatellite ranging monitors. Also delays due to onboard signal propagation and processing have a nonnegligible…
▽ More
Time-delay interferometry (TDI) is a data processing technique for space-based gravitational-wave detectors to create laser-noise-free equal-optical-path-length interferometers virtually on the ground. It relies on the interspacecraft signal propagation delays, which are delivered by intersatellite ranging monitors. Also delays due to onboard signal propagation and processing have a nonnegligible impact on the TDI combinations. However, these onboard delays were only partially considered in previous TDI-related research; onboard optical path lengths have been neglected so far. In this paper, we study onboard optical path lengths in TDI. We derive analytical models for their coupling to the second-generation TDI Michelson combinations and verify these models numerically. Furthermore, we derive a compensation scheme for onboard optical path lengths in TDI and validate its performance via numerical simulations.
△ Less
Submitted 31 May, 2024; v1 submitted 30 May, 2024;
originally announced May 2024.
-
Compensation of front-end and modulation delays in phase and ranging measurements for time-delay interferometry
Authors:
Philipp Euringer,
Niklas Houba,
Gerald Hechenblaikner,
Oliver Mandel,
Francis Soualle,
Walter Fichter
Abstract:
In the context of the Laser Interferometer Space Antenna (LISA), the laser subsystems exhibit frequency fluctuations that introduce significant levels of noise into the measurements, surpassing the gravitational wave signal by several orders of magnitude. Mitigation is achieved via time-shifting individual measurements in a data processing step known as time-delay interferometry (TDI). The suppres…
▽ More
In the context of the Laser Interferometer Space Antenna (LISA), the laser subsystems exhibit frequency fluctuations that introduce significant levels of noise into the measurements, surpassing the gravitational wave signal by several orders of magnitude. Mitigation is achieved via time-shifting individual measurements in a data processing step known as time-delay interferometry (TDI). The suppression performance of TDI relies on accurate knowledge and consideration of the delays experienced by the interfering lasers. While considerable efforts have been dedicated to the accurate determination of inter-spacecraft ranging delays, the sources for onboard delays have been either neglected or assumed to be known. Contrary to these assumptions, analog delays of the phasemeter front end and the laser modulator are not only large but also prone to change with temperature and heterodyne frequency. This motivates our proposal for a novel method enabling a calibration of these delays on-ground and in-space, based on minimal functional additions to the receiver architecture. Specifically, we establish a set of calibration measurements and elucidate how these measurements are utilized in data processing, leading to the mitigation of the delays in the TDI Michelson variables. Following a performance analysis of the calibration measurements, proposed calibration scheme is assessed through numerical simulations. We find that in the absence of the calibration scheme, the assumed drifts of the analog delays increase residual laser noise at high frequencies of the LISA measurement band. A single, on-ground calibration of the analog delays leads to an improvement by roughly one order of magnitude, while re-calibration in space may improve performance by yet another order of magnitude. Towards lower frequencies, ranging error is always found to be the limiting factor for which countermeasures are discussed.
△ Less
Submitted 12 January, 2024; v1 submitted 5 December, 2023;
originally announced December 2023.
-
Unbiased centroiding of point targets close to the Cramer Rao limit
Authors:
Gerald Hechenblaikner
Abstract:
Systematic errors affecting center-of-gravity (CoG) measurements may occur from coarse sampling of the point-spread-function (PSF) or from signal truncation at the boundaries of the region-of-interest (ROI). For small ROI and PSF widths, these effects are shown to become dominant, but this can be mitigated by introducing novel unbiased estimators that are largely free of systematic error and perfo…
▽ More
Systematic errors affecting center-of-gravity (CoG) measurements may occur from coarse sampling of the point-spread-function (PSF) or from signal truncation at the boundaries of the region-of-interest (ROI). For small ROI and PSF widths, these effects are shown to become dominant, but this can be mitigated by introducing novel unbiased estimators that are largely free of systematic error and perform particularly well for low photon number. Analytical expressions for the estimator variances, comprising contributions from photon shot noise, random pixel noise and residual systematic error, are derived and verified by Monte Carlo simulations. The accuracy and computational speed of the unbiased estimators is compared to those of other common estimators, including iteratively weighted CoG, thresholded CoG, iterative least squares fitting, and two-dimensional Gaussian regression. Each estimator is optimized with respect to ROI size and PSF radius and its error compared to the theoretical limit defined by the Cramer Rao lower bound (CRLB). The unbiased estimator with full systematic error correction operating on a small ROI [3x3] emerges as one of the most accurate estimators while requiring significantly less computing effort than alternative algorithms.
△ Less
Submitted 20 December, 2023; v1 submitted 18 July, 2023;
originally announced July 2023.
-
Performance analysis of sequential carrier- and code-tracking receivers in the context of high-precision space-borne metrology systems
Authors:
Philipp Euringer,
Gerald Hechenblaikner,
Francis Soualle,
Walter Fichter
Abstract:
Future space observatories achieve detection of gravitational waves by interferometric measurements of a carrier phase, allowing to determine relative distance changes, in combination with an absolute distance measurement based on the transmission of pseudo-random noise chip sequences. In addition, usage of direct-sequence spread spectrum modulation enables data transmission. Hereafter, we report…
▽ More
Future space observatories achieve detection of gravitational waves by interferometric measurements of a carrier phase, allowing to determine relative distance changes, in combination with an absolute distance measurement based on the transmission of pseudo-random noise chip sequences. In addition, usage of direct-sequence spread spectrum modulation enables data transmission. Hereafter, we report on the findings of a novel performance evaluation of planned receiver architectures, performing phase and distance readout sequentially, addressing the interplay between both measurements. An analytical model is presented identifying the power spectral density of the chip modulation at frequencies within the measurement bandwidth as the main driver for phase noise. This model, verified by numerical simulations, excludes binary phase-shift keying modulations for missions requiring pico-meter noise levels at the phase readout, while binary offset carrier modulation, where most of the power has been shifted outside the measurement bandwidth, exhibits superior phase measurement performance. Ranging analyses of the delay-locked loop reveal strong distortion of the pulse shape due to the preceding phase tracking introducing ranging bias variations. Numerical simulations show that these variations, however, which originate from data transitions, are compensated by the delay tracking loop, enabling sub-meter ranging accuracy, irrespective of the modulation type.
△ Less
Submitted 10 January, 2024; v1 submitted 23 February, 2023;
originally announced February 2023.
-
Optical link acquisition for the LISA mission with in-field pointing architecture
Authors:
Gerald Hechenblaikner,
Simon Delchambre,
Tobias Ziegler
Abstract:
We present a comprehensive simulation of the spatial acquisition of optical links for the LISA mission in the in-field pointing architecture, where a fast pointing mirror is used to move the field-of-view of the optical transceiver, which was studied as an alternative scheme to the baselined telescope pointing architecture. The simulation includes a representative model of the far-field intensity…
▽ More
We present a comprehensive simulation of the spatial acquisition of optical links for the LISA mission in the in-field pointing architecture, where a fast pointing mirror is used to move the field-of-view of the optical transceiver, which was studied as an alternative scheme to the baselined telescope pointing architecture. The simulation includes a representative model of the far-field intensity distribution and the beam detection process using a realistic detector model, and a model of the expected platform jitter for two alternative control modes with different associated jitter spectra. For optimally adjusted detector settings and accounting for the actual far-field beam profile, we investigate the dependency of acquisition performance on the jitter spectrum and the track-width of the search spiral, while scan speed and detector integration time are varied over several orders of magnitude. Results show a strong dependency of the probability for acquisition failure on the width of the auto-correlation function of the jitter spectrum, which we compare to predictions of analytical models. Depending on the choice of scan speed, three different regimes may be entered which differ in failure probability by several orders of magnitude. We then use these results to optimize the acquisition architecture for the given jitter spectra with respect to failure rate and overall duration, concluding that the full constellation could be acquired on average in less than one minute. Our method and findings can be applied to any other space mission using a fine-steering mirror for link acquisition.
△ Less
Submitted 23 February, 2023;
originally announced February 2023.
-
Probabilistic model for spatially acquiring optical links in space under influence of band-limited beam jitter
Authors:
Gerald Hechenblaikner
Abstract:
An analytical model is derived for the probability of failure (P-fail) to spatially acquire an optical link with a jittering search beam. The analytical model accounts for an arbitrary jitter spectrum and considers the associated correlations between jitter excursions on adjacent tracks of the search spiral. An expression of P-fail in terms of basic transcendental functions is found by linearizing…
▽ More
An analytical model is derived for the probability of failure (P-fail) to spatially acquire an optical link with a jittering search beam. The analytical model accounts for an arbitrary jitter spectrum and considers the associated correlations between jitter excursions on adjacent tracks of the search spiral. An expression of P-fail in terms of basic transcendental functions is found by linearizing the exact analytical model with respect to the correlation strength. Predictions from the models indicate a strong decrease of P-fail with increasing correlation-strength, which is found to be in excellent agreement to results from Monte Carlo simulations. The dependency of P-fail on track-width and scan speed is investigated, confirming previous assumptions on the impact of correlations. Expressions and applicable constraints are derived for the limits of full and no correlations, and the optimal track width to minimize the acquisition time is computed for a range of scan speeds. The model is applicable to optical terminals equipped with a fast beam steering mirror, as often found for optical communication missions in space.
△ Less
Submitted 18 February, 2023;
originally announced February 2023.
-
LISA Point-Ahead Angle Control for Optimal Tilt-to-Length Noise Estimation
Authors:
Niklas Houba,
Simon Delchambre,
Tobias Ziegler,
Gerald Hechenblaikner,
Walter Fichter
Abstract:
The Laser Interferometer Space Antenna (LISA) mission features a three-spacecraft long-arm constellation intended to detect gravitational wave sources in the low-frequency band up to 1 Hz via laser interferometry. The paper presents an open-loop control strategy for point-ahead angle (PAA) correction required to maintain the optical links of the moving constellation. The control strategy maximizes…
▽ More
The Laser Interferometer Space Antenna (LISA) mission features a three-spacecraft long-arm constellation intended to detect gravitational wave sources in the low-frequency band up to 1 Hz via laser interferometry. The paper presents an open-loop control strategy for point-ahead angle (PAA) correction required to maintain the optical links of the moving constellation. The control strategy maximizes periods between adjustments at the constellation level and is shown to be optimal from the perspective of estimating and correcting tilt-to-length (TTL) coupling. TTL is a noise source that couples angular spacecraft jitter and jitter of optical subassemblies with longitudinal interferometer measurements. Without precise TTL noise estimation and correction, TTL coupling fundamentally limits the detector's sensitivity.
△ Less
Submitted 23 August, 2022;
originally announced August 2022.
-
Impact of spectral noise shape and correlations of laser beam jitter on acquiring optical links in space
Authors:
Gerald Hechenblaikner
Abstract:
We investigate how the probability of acquiring an optical link between a scanning and a target spacecraft depends on the spectral shape, power and dimensionality of the beam jitter, as well as on the choice of detector integration time, beam detection radius and scan speed. For slow scans and long integration times, the probability of failure (Pfail) is determined by the integrated jitter power u…
▽ More
We investigate how the probability of acquiring an optical link between a scanning and a target spacecraft depends on the spectral shape, power and dimensionality of the beam jitter, as well as on the choice of detector integration time, beam detection radius and scan speed. For slow scans and long integration times, the probability of failure (Pfail) is determined by the integrated jitter power up to a critical frequency, which we verify by comparing the results of an analytical model to those of Monte Carlo simulations. Jitter above the critical frequency leads to a loss of correlation between integration windows and decreases Pfail for both, 1d (radial) and 2d (radial and tangential) jitter, as long as the RMS jitter amplitude does not exceed the beam diameter. In the opposite limit of fast scans and short integration times, emergent correlations between jitter fluctuations on two adjacent scanning tracks also decrease Pfail. The analytical model is additionally used to assess the effect of multiple overlap** tracks and the impact of target drifts in the uncertainty plane.
△ Less
Submitted 1 February, 2022;
originally announced February 2022.
-
MAQRO -- BPS 2023 Research Campaign Whitepaper
Authors:
Rainer Kaltenbaek,
Markus Arndt,
Markus Aspelmeyer,
Peter F. Barker,
Angelo Bassi,
James Bateman,
Alessio Belenchia,
Joel Bergé,
Sougato Bose,
Claus Braxmaier,
Bruno Christophe,
Garrett D. Cole,
Catalina Curceanu,
Animesh Datta,
Maxime Debiossac,
Uroš Delić,
Lajos Diósi,
Andrew A. Geraci,
Stefan Gerlich,
Christine Guerlin,
Gerald Hechenblaikner,
Antoine Heidmann,
Sven Herrmann,
Klaus Hornberger,
Ulrich Johann
, et al. (21 additional authors not shown)
Abstract:
The objective of the proposed MAQRO mission is to harness space for achieving long free-fall times, extreme vacuum, nano-gravity, and cryogenic temperatures to test the foundations of physics in macroscopic quantum experiments. This will result in the development of novel quantum sensors and a means to probe the foundations of quantum physics at the interface with gravity. Earlier studies showed t…
▽ More
The objective of the proposed MAQRO mission is to harness space for achieving long free-fall times, extreme vacuum, nano-gravity, and cryogenic temperatures to test the foundations of physics in macroscopic quantum experiments. This will result in the development of novel quantum sensors and a means to probe the foundations of quantum physics at the interface with gravity. Earlier studies showed that the proposal is feasible but that several critical challenges remain, and key technologies need to be developed. These new technologies will open up the potential for achieving additional science objectives. The proposed research campaign aims to advance the state of the art and to perform the first macroscopic quantum experiments in space. Experiments on the ground, in micro-gravity, and in space will drive the proposed research campaign during the current decade to enable the implementation of MAQRO within the subsequent decade.
△ Less
Submitted 3 February, 2022;
originally announced February 2022.
-
Analysis of performance and robustness against jitter of various search methods for acquiring optical links in space
Authors:
Gerald Hechenblaikner
Abstract:
We discuss various methods for acquiring optical links in space using a dedicated acquisition sensor. Statistical models are developed and simple analytical equations derived that compare the performance between a single and dual spiral scan approach as well as between sequential and parallel acquisition of link chains. Simple derived analytical equations allow relating essential search parameters…
▽ More
We discuss various methods for acquiring optical links in space using a dedicated acquisition sensor. Statistical models are developed and simple analytical equations derived that compare the performance between a single and dual spiral scan approach as well as between sequential and parallel acquisition of link chains. Simple derived analytical equations allow relating essential search parameters such as track width, variance of the uncertainty distribution, capture radius and scan speed to the probabilities of acquiring the links within a specific time. We also assess the probability of failing to acquire a link due to beam jitter and derive a simple analytical model that allows determining the maximum tolerable jitter for a given beam overlap and required probability of success. All results are validated by Monte Carlo simulations and applied to the concrete example of the GRACE FO mission.
△ Less
Submitted 17 November, 2022; v1 submitted 1 February, 2022;
originally announced February 2022.
-
Performance of a radiatively cooled system for quantum optomechanical experiments in space
Authors:
André Pilan-Zanoni,
Johannes Burkhardt,
Ulrich Johann,
Markus Aspelmeyer,
Rainer Kaltenbaek,
Gerald Hechenblaikner
Abstract:
The performance of a radiatively cooled instrument is investigated in the context of optomechanical quantum experiments, where the environment of a macroscopic particle in a quantum-superposition has to be cooled to less than 20\,K in deep space. A heat-transfer analysis between the components of the instrument as well as a transfer-function analysis on thermal oscillations induced by the spacecra…
▽ More
The performance of a radiatively cooled instrument is investigated in the context of optomechanical quantum experiments, where the environment of a macroscopic particle in a quantum-superposition has to be cooled to less than 20\,K in deep space. A heat-transfer analysis between the components of the instrument as well as a transfer-function analysis on thermal oscillations induced by the spacecraft interior and by dissipative sources is performed. The thermal behaviour of the instrument in an orbit around a Lagrangian point and in a highly elliptical Earth orbit is discussed. Finally, we investigate further possible design improvements aiming at lower temperatures of the environment of the macroscopic particle. These include a mirror-based design of the imaging system on the optical bench and the extension of the heat shields.
△ Less
Submitted 5 August, 2015;
originally announced August 2015.
-
Macroscopic quantum resonators (MAQRO): 2015 Update
Authors:
Rainer Kaltenbaek,
Markus Arndt,
Markus Aspelmeyer,
Peter F. Barker,
Angelo Bassi,
James Bateman,
Kai Bongs,
Sougato Bose,
Claus Braxmaier,
Časlav Brukner,
Bruno Christophe,
Michael Chwalla,
Pierre-François Cohadon,
Adrian M. Cruise,
Catalina Curceanu,
Kishan Dholakia,
Klaus Döringshoff,
Wolfgang Ertmer,
Jan Gieseler,
Norman Gürlebeck,
Gerald Hechenblaikner,
Antoine Heidmann,
Sven Herrmann,
Sabine Hossenfelder,
Ulrich Johann
, et al. (27 additional authors not shown)
Abstract:
Do the laws of quantum physics still hold for macroscopic objects - this is at the heart of Schrödinger's cat paradox - or do gravitation or yet unknown effects set a limit for massive particles? What is the fundamental relation between quantum physics and gravity? Ground-based experiments addressing these questions may soon face limitations due to limited free-fall times and the quality of vacuum…
▽ More
Do the laws of quantum physics still hold for macroscopic objects - this is at the heart of Schrödinger's cat paradox - or do gravitation or yet unknown effects set a limit for massive particles? What is the fundamental relation between quantum physics and gravity? Ground-based experiments addressing these questions may soon face limitations due to limited free-fall times and the quality of vacuum and microgravity. The proposed mission MAQRO may overcome these limitations and allow addressing those fundamental questions. MAQRO harnesses recent developments in quantum optomechanics, high-mass matter-wave interferometry as well as state-of-the-art space technology to push macroscopic quantum experiments towards their ultimate performance limits and to open new horizons for applying quantum technology in space. The main scientific goal of MAQRO is to probe the vastly unexplored "quantum-classical" transition for increasingly massive objects, testing the predictions of quantum theory for truly macroscopic objects in a size and mass regime unachievable in ground-based experiments. The hardware for the mission will largely be based on available space technology. Here, we present the MAQRO proposal submitted in response to the (M4) Cosmic Vision call of the European Space Agency for a medium-size mission opportunity with a possible launch in 2025.
△ Less
Submitted 9 March, 2015;
originally announced March 2015.
-
The vectorial photoelectric effect under solar irradiance and its application to sun sensing
Authors:
Gerald Hechenblaikner,
Tobias Ziegler
Abstract:
Sun sensors are an integral part of the attitude and orbit control system onboard almost any spacecraft. While the majority of standard analogue sun sensors is based on photo-detectors which produce photo-currents proportional to the cosine of the incidence angle (cosine detectors), we propose an alternative scheme where the vectorial photoelectric effect is exploited to achieve a higher sensitivi…
▽ More
Sun sensors are an integral part of the attitude and orbit control system onboard almost any spacecraft. While the majority of standard analogue sun sensors is based on photo-detectors which produce photo-currents proportional to the cosine of the incidence angle (cosine detectors), we propose an alternative scheme where the vectorial photoelectric effect is exploited to achieve a higher sensitivity of the sensed photo-current to the incidence angle. The vectorial photo-effect is investigated in detail for metal cathode detectors in a space environment. Besides long operational lifetimes without significant degradation, metal cathode detectors are insensitive to earth albedo, which may significantly reduce the errors affecting attitude measurements in low earth orbits. Sensitivity curves are calculated and trade-offs performed with the aim of optimizing the sensitivity whilst also providing currents sufficient for detection. Simple applications and detector configurations are also discussed and compared to existing designs.
△ Less
Submitted 28 May, 2014;
originally announced May 2014.
-
STE-QUEST Mission and System Design - Overview after completion of Phase-A
Authors:
Gerald Hechenblaikner,
Marc-Peter Hess,
Marianna Vitelli,
Jan Beck
Abstract:
STE-QUEST is a fundamental science mission which is considered for launch within the Cosmic Vision programme of the European Space Agency (ESA). Its main scientific objectives relate to probing various aspects of Einstein's theory of general relativity by measuring the gravitational red-shift of the earth, the moon and the sun as well as testing the weak equivalence principle to unprecedented accu…
▽ More
STE-QUEST is a fundamental science mission which is considered for launch within the Cosmic Vision programme of the European Space Agency (ESA). Its main scientific objectives relate to probing various aspects of Einstein's theory of general relativity by measuring the gravitational red-shift of the earth, the moon and the sun as well as testing the weak equivalence principle to unprecedented accuracy. In order to perform the measurements, the system features a spacecraft equipped with two complex instruments, an atomic clock and an atom interferometer, a ground-segment encompassing several ground-terminals collocated with the best available ground atomic clocks, and clock comparison between space and ground via microwave and optical links. The baseline orbit is highly eccentric and exhibits strong variations of incident solar flux, which poses challenges for thermal and power subsystems in addition to the difficulties encountered by precise-orbit-determination at high altitudes. The mission assessment and definition phase (Phase-A) has recently been completed and this paper gives a concise overview over some system level results.
△ Less
Submitted 25 January, 2014; v1 submitted 30 September, 2013;
originally announced October 2013.
-
How cold can you get in space? Quantum Physics at cryogenic temperatures in space
Authors:
Gerald Hechenblaikner,
Fabian Hufgard,
Johannes Burkhardt,
Nikolai Kiesel,
Ulrich Johann,
Markus Aspelmeyer,
Rainer Kaltenbaek
Abstract:
Although it is often believed that the coldness of space is ideally suited for performing measurements at cryogenic temperatures, this must be regarded with caution for two reasons: Firstly, the sensitive instrument must be completely shielded from the strong solar radiation and therefore, e.g. either be placed inside a satellite or externally on the satellite's shaded side. Secondly, any platform…
▽ More
Although it is often believed that the coldness of space is ideally suited for performing measurements at cryogenic temperatures, this must be regarded with caution for two reasons: Firstly, the sensitive instrument must be completely shielded from the strong solar radiation and therefore, e.g. either be placed inside a satellite or externally on the satellite's shaded side. Secondly, any platform hosting such an experiment in space generally provides an environment close to room temperature for the accommodated equipment. To obtain cryogenic temperatures without active cooling, one must isolate the instrument from radiative and conductive heat exchange with the platform as well as possible. We investigate the limits of this passive cooling method in the context of a recently proposed experiment to observe the decoherence of quantum superpositions of massive objects. The analyses and conclusions are applicable to a host of similar experimental designs requiring a cryogenic environment in space.
△ Less
Submitted 13 September, 2013; v1 submitted 12 September, 2013;
originally announced September 2013.
-
Fundamental Performance Determining Factors of the Ultrahigh-Precision Space-Borne Optical Metrology System for the LISA Pathfinder mission
Authors:
Gerald Hechenblaikner,
Reinhold Flatscher
Abstract:
The LISA Pathfinder mission to space employs an optical metrology system (OMS) at its core to measure the distance and attitude between two freely floating test-masses to picometer and nanorad accuracy, respectively, within the measurement band of [1 mHz, 30 mHz]. The OMS is based upon an ultra-stable optical bench with 4 heterodyne interferometers from which interference signals are read-out and…
▽ More
The LISA Pathfinder mission to space employs an optical metrology system (OMS) at its core to measure the distance and attitude between two freely floating test-masses to picometer and nanorad accuracy, respectively, within the measurement band of [1 mHz, 30 mHz]. The OMS is based upon an ultra-stable optical bench with 4 heterodyne interferometers from which interference signals are read-out and processed by a digital phase-meter. Laser frequency noise, power fluctuations and optical path-length variations are suppressed to uncritical levels by dedicated control loops so that the measurement performance approaches the sensor limit imposed by the phase-meter. The system design is such that low frequency common mode noise which affects the read-out phase of all four interferometers is generally well suppressed by subtraction of a reference phase from the other interferometer signals. However, high frequency noise directly affects measurement performance and its common mode rejection depends strongly on the relative signal phases. We discuss how the data from recent test campaigns point towards high frequency phase noise as a likely performance limiting factor which explains some important performance features.
△ Less
Submitted 30 July, 2013;
originally announced July 2013.
-
Common mode noise rejection properties of amplitude and phase noise in a heterodyne interferometer
Authors:
Gerald Hechenblaikner
Abstract:
High precision metrology systems based on heterodyne interferometry can measure position and attitude of objects to accuracies of picometer and nanorad, respectively. A frequently found feature of the general system design is the subtraction of a reference phase from the phase of the position interferometer, which suppresses low frequency common mode amplitude and phase fluctuations occurring in v…
▽ More
High precision metrology systems based on heterodyne interferometry can measure position and attitude of objects to accuracies of picometer and nanorad, respectively. A frequently found feature of the general system design is the subtraction of a reference phase from the phase of the position interferometer, which suppresses low frequency common mode amplitude and phase fluctuations occurring in volatile optical path sections shared by both, the position and reference interferometer. Spectral components of the noise at frequencies around or higher than the heterodyne frequency, however, are generally transmitted into the measurement band and may limit the measurement accuracy. Detailed analytical calculations complemented with Monte Carlo simulations show that high frequency noise components may also be entirely suppressed, depending on the relative difference of measurement and reference phase, which may be exploited by corresponding design provisions. Whilst these results are applicable to any heterodyne interferometer with certain design characteristics, specific calculations and related discussions are given for the example of the optical metrology system of the LISA Pathfinder mission to space.
△ Less
Submitted 22 March, 2013;
originally announced March 2013.
-
Probing the Flyby Anomaly with the future STE-QUEST mission
Authors:
Jorge Páramos,
Gerald Hechenblaikner
Abstract:
In this study, we demonstrate that the flyby anomaly, an unexpected acceleration detected in some of the gravitational assists of the Galileo, NEAR, Cassini and Rosetta spacecraft, could be probed by accurate orbital tracking available in the proposed Space-Time Explorer and Quantum Equivalence Principle Space Test (STE- QUEST); following a recent work, we focus on the similarity between an hyperb…
▽ More
In this study, we demonstrate that the flyby anomaly, an unexpected acceleration detected in some of the gravitational assists of the Galileo, NEAR, Cassini and Rosetta spacecraft, could be probed by accurate orbital tracking available in the proposed Space-Time Explorer and Quantum Equivalence Principle Space Test (STE- QUEST); following a recent work, we focus on the similarity between an hyperbolic flyby and the perigee passage in a highly elliptic orbit of the latter, as well as its Global Navigation Satellite System precise orbital determination capabilities.
△ Less
Submitted 27 October, 2012;
originally announced October 2012.
-
Modeling and Performance of Contact-Free Discharge Systems for Space Inertial Sensors
Authors:
Tobias Ziegler,
Patrick Bergner,
Gerald Hechenblaikner,
Nico Brandt,
Walter Fichter
Abstract:
This article presents a detailed overview and assessment of contact-free UV light discharge systems (UVDS) needed to control the variable electric charge level of free-flying test masses which are part of high precision inertial sensors in space. A comprehensive numerical analysis approach on the basis of experimental data is detailed. This includes UV light ray tracing, the computation of time va…
▽ More
This article presents a detailed overview and assessment of contact-free UV light discharge systems (UVDS) needed to control the variable electric charge level of free-flying test masses which are part of high precision inertial sensors in space. A comprehensive numerical analysis approach on the basis of experimental data is detailed. This includes UV light ray tracing, the computation of time variant electric fields inside the complex inertial sensor geometry, and the simulation of individual photo-electron trajectories. Subsequent data analysis allows to determine key parameters to set up an analytical discharge model. Such a model is an essential system engineering tool needed for requirement breakdown and subsystem specification, performance budgeting, on-board charge control software development, and instrument modeling within spacecraft end-to-end performance simulators. Different types of UVDS design concepts are presented and assessed regarding their robustness and performance. Critical hardware aspects like electron emission from air-contaminated surfaces, interfaces with other subsystems, and spacecraft operations are considered. The focus is on the modeling and performance evaluation of the existing UVDS on board LISA Pathfinder, an ESA technology demonstrator spacecraft to be launched in 2014. The results have motivated the design of a more robust discharge system concept for cubical test mass inertial sensors for future space missions. The developed analysis tools have been used for design optimization and performance assessment of the proposed design. A significant improvement of relevant robustness and performance figures has been achieved.
△ Less
Submitted 3 July, 2012; v1 submitted 2 July, 2012;
originally announced July 2012.
-
Energy distribution and quantum yield for photoemission from air-contaminated gold surfaces under UV illumination close to the threshold
Authors:
Gerald Hechenblaikner,
Tobias Ziegler,
Indro Biswas,
Christoph Seibel,
Mathias Schulze,
Nico Brandt,
Achim Schoell,
Patrick Bergner,
Friedrich T. Reinert
Abstract:
The kinetic energy distributions of photo-electrons emitted from gold surfaces under illumination by UV-light close to the threshold are measured and analyzed. Samples are prepared as chemically clean through Ar-Ion sputtering and then exposed to atmosphere for variable durations before Quantum Yield measurements are performed after evacuation. During measurements the bias voltage applied to the s…
▽ More
The kinetic energy distributions of photo-electrons emitted from gold surfaces under illumination by UV-light close to the threshold are measured and analyzed. Samples are prepared as chemically clean through Ar-Ion sputtering and then exposed to atmosphere for variable durations before Quantum Yield measurements are performed after evacuation. During measurements the bias voltage applied to the sample is varied and the resulting emission current measured. Taking the derivative of the current-voltage curve yields the energy distribution which is found to closely resemble the distribution of total energies derived by DuBridge for emission from a free electron gas. We investigate the dependence of distribution shape and width on electrode geometry and contaminant substances adsorbed from the atmosphere, in particular to water and hydro-carbons. Emission efficiency increases initially during air exposure before diminishing to zero on a timescale of several hours, whilst subsequent annealing of the sample restores emissivity. A model fit function, in good quantitative agreement with the measured data, is introduced which accounts for the experiment-specific electrode geometry and an energy dependent transmission coefficient. The impact of large patch potential fields from contact potential drops between sample and sample holder is investigated. The total quantum yield is split into bulk and surface contributions which are tested for their sensitivity to light incidence angle and polarization. Our results are directly applicable to model parameters for the contact-free discharge system onboard the LISA Pathfinder spacecraft.
△ Less
Submitted 6 June, 2012;
originally announced June 2012.
-
Digital laser frequency control and phase stabilization loops for a high precision space-borne metrology system
Authors:
Gerald Hechenblaikner,
Vinzenz Wand,
Michael Kersten,
Karsten Danzmann,
Antonio Garcia,
Gerhard Heinzel,
Miquel Nofrarias,
Frank Steier
Abstract:
We report on the design, implementation and characterization of fully digital control loops for laser frequency stabilization, differential phase-locking and performance optimization of the optical metrology system on-board the LISA Pathfinder space mission. The optical metrology system consists of a laser with modulator, four Mach-Zehnder interferometers, a phase-meter and a digital processing un…
▽ More
We report on the design, implementation and characterization of fully digital control loops for laser frequency stabilization, differential phase-locking and performance optimization of the optical metrology system on-board the LISA Pathfinder space mission. The optical metrology system consists of a laser with modulator, four Mach-Zehnder interferometers, a phase-meter and a digital processing unit for data analysis. The digital loop design has the advantage of easy and flexible controller implementation and loop calibration, automated and flexible locking and resetting, and improved performance over analogue circuitry. Using the practical ability of our system to modulate the laser frequency allows us to accurately determine the open loop transfer function and other system properties. Various noise sources and their impact on system performance are investigated in detail.
△ Less
Submitted 21 May, 2012;
originally announced May 2012.
-
Macroscopic quantum resonators (MAQRO)
Authors:
Rainer Kaltenbaek,
Gerald Hechenblaikner,
Nikolai Kiesel,
Oriol Romero-Isart,
Keith C. Schwab,
Ulrich Johann,
Markus Aspelmeyer
Abstract:
Quantum physics challenges our understanding of the nature of physical reality and of space-time and suggests the necessity of radical revisions of their underlying concepts. Experimental tests of quantum phenomena involving massive macroscopic objects would provide novel insights into these fundamental questions. Making use of the unique environment provided by space, MAQRO aims at investigating…
▽ More
Quantum physics challenges our understanding of the nature of physical reality and of space-time and suggests the necessity of radical revisions of their underlying concepts. Experimental tests of quantum phenomena involving massive macroscopic objects would provide novel insights into these fundamental questions. Making use of the unique environment provided by space, MAQRO aims at investigating this largely unexplored realm of macroscopic quantum physics. MAQRO has originally been proposed as a medium-sized fundamental-science space mission for the 2010 call of Cosmic Vision. MAQRO unites two experiments: DECIDE (DECoherence In Double-Slit Experiments) and CASE (Comparative Acceleration Sensing Experiment). The main scientific objective of MAQRO, which is addressed by the experiment DECIDE, is to test the predictions of quantum theory for quantum superpositions of macroscopic objects containing more than 10e8 atoms. Under these conditions, deviations due to various suggested alternative models to quantum theory would become visible. These models have been suggested to harmonize the paradoxical quantum phenomena both with the classical macroscopic world and with our notion of Minkowski space-time. The second scientific objective of MAQRO, which is addressed by the experiment CASE, is to demonstrate the performance of a novel type of inertial sensor based on optically trapped microspheres. CASE is a technology demonstrator that shows how the modular design of DECIDE allows to easily incorporate it with other missions that have compatible requirements in terms of spacecraft and orbit. CASE can, at the same time, serve as a test bench for the weak equivalence principle, i.e., the universality of free fall with test-masses differing in their mass by 7 orders of magnitude.
△ Less
Submitted 19 March, 2012; v1 submitted 23 January, 2012;
originally announced January 2012.
-
Measurement of the absolute wavefront curvature radius in a heterodyne interferometer
Authors:
Gerald Hechenblaikner
Abstract:
We present an analytical derivation of the coupling parameter relating the angle between two interfering beams in a heterodyne interferometer to the differential phase-signals detected by a quadrant photo-diode. This technique, also referred to as Differential Wavefront Sensing (DWS), is commonly used in space-based gravitational wave detectors to determine the attitude of a test-mass in one of th…
▽ More
We present an analytical derivation of the coupling parameter relating the angle between two interfering beams in a heterodyne interferometer to the differential phase-signals detected by a quadrant photo-diode. This technique, also referred to as Differential Wavefront Sensing (DWS), is commonly used in space-based gravitational wave detectors to determine the attitude of a test-mass in one of the interferometer arms from the quadrant diode signals. Successive approximations to the analytical expression are made to simplify the investigation of parameter dependencies. Motivated by our findings, we propose a new measurement method to accurately determine the absolute wave-front curvature of a single measurement beam. We also investigate the change in coupling parameter when the interferometer "test-mirror" is moved from its nominal position, an effect which mediates the coupling of mirror displacement noise into differential phase-measurements.
△ Less
Submitted 21 June, 2010;
originally announced June 2010.
-
Coupling characterization and noise studies of the Optical Metrology System on-board the LISA Pathfinder Mission
Authors:
G. Hechenblaikner,
R. Gerndt,
U. Johann,
P. Luetzow-Wentzky,
V. Wand,
H. Audley,
K. Danzmann,
A. Garcia-Marin,
G. Heinzel,
M. Nofrarias,
F. Steier
Abstract:
In this article we describe the first investigations of the complete engineering model of the Optical Metrology System (OMS), a key subsystem of the LISA Pathfinder science mission to space. The latter itself is a technological precursor mission to LISA, a space-borne gravitational wave detector. At its core, the OMS consists of four heterodyne Mach Zehnder interferometers, a highly stable laser w…
▽ More
In this article we describe the first investigations of the complete engineering model of the Optical Metrology System (OMS), a key subsystem of the LISA Pathfinder science mission to space. The latter itself is a technological precursor mission to LISA, a space-borne gravitational wave detector. At its core, the OMS consists of four heterodyne Mach Zehnder interferometers, a highly stable laser with external modulator and a phase-meter. It is designed to monitor and track the longitudinal motion and attitude of two floating test-masses in the optical reference frame with a (relative) precision in the picometer and nanorad range, respectively. We analyze sensor signal correlations and determine a physical sensor noise limit. The coupling parameters between motional degrees of freedom and interferometer signals are analytically derived and compared to measurements. We also measure adverse cross-coupling effects originating from system imperfections and limitations and describe algorithmic mitigation techniques to overcome some of them. Their impact on system performance is analyzed in the context of the Pathfinder mission.
△ Less
Submitted 10 June, 2010;
originally announced June 2010.
-
Testing and design of a lens system for atom trap** and fluorescence detection
Authors:
P Baranowski,
J Zacks,
G Hechenblaikner,
C J Foot
Abstract:
We present methods and results of the testing of an inexpensive home-made diffraction limited lens system, the design of which was proposed in a recent paper and which has since been used (with slight alterations) by several research groups. Our system will be used for both: focussing a collimated laser beam at a wavelength of lambda=830 nm down to a narrow spot and for collimating fluorescence…
▽ More
We present methods and results of the testing of an inexpensive home-made diffraction limited lens system, the design of which was proposed in a recent paper and which has since been used (with slight alterations) by several research groups. Our system will be used for both: focussing a collimated laser beam at a wavelength of lambda=830 nm down to a narrow spot and for collimating fluorescence light (lambda=780 nm) emitted from rubidium atoms captured in this spot. Useful tests for lens systems include the use of ray tracing software, shear-wave interferometers, the imaging of test charts and of polystyrene beads of a very small size. We present these methods and show how conclusions can be drawn for the design under test.
△ Less
Submitted 20 December, 2004;
originally announced December 2004.
-
Properties of quasi two-dimensional condensates in highly anisotropic traps
Authors:
G. Hechenblaikner,
J. M. Krueger,
C. J. Foot
Abstract:
We theoretically investigate some of the observable properties of quasi two-dimensional condensates. Using a variational model based on a Gaussian-parabolic trial wavefunction we calculate chemical potential, condensate size in time-of-flight, release energy and collective excitation spectrum for varying trap geometries and atom numbers and find good agreement with recent published experimental…
▽ More
We theoretically investigate some of the observable properties of quasi two-dimensional condensates. Using a variational model based on a Gaussian-parabolic trial wavefunction we calculate chemical potential, condensate size in time-of-flight, release energy and collective excitation spectrum for varying trap geometries and atom numbers and find good agreement with recent published experimental results.
△ Less
Submitted 6 October, 2004;
originally announced October 2004.
-
Quasi-2D Confinement of a BEC in a Combined Optical and Magnetic Potential
Authors:
N. L. Smith,
W. H. Heathcote,
G. Hechenblaikner,
E. Nugent,
C. J. Foot
Abstract:
We have added an optical potential to a conventional Time-averaged Orbiting Potential (TOP) trap to create a highly anisotropic hybrid trap for ultracold atoms. Axial confinement is provided by the optical potential; the maximum frequency currently obtainable in this direction is 2.2 kHz for rubidium. The radial confinement is independently controlled by the magnetic trap and can be a factor of…
▽ More
We have added an optical potential to a conventional Time-averaged Orbiting Potential (TOP) trap to create a highly anisotropic hybrid trap for ultracold atoms. Axial confinement is provided by the optical potential; the maximum frequency currently obtainable in this direction is 2.2 kHz for rubidium. The radial confinement is independently controlled by the magnetic trap and can be a factor of 700 times smaller than in the axial direction. This large anisotropy is more than sufficient to confine condensates with ~10^5 atoms in a Quasi-2D (Q2D) regime, and we have verified this by measuring a change in the free expansion of the condensate; our results agree with a variational model.
△ Less
Submitted 5 October, 2004;
originally announced October 2004.
-
The Experimental Observation of a Superfluid Gyroscope in a dilute Bose Condensed Gas
Authors:
E. Hodby,
S. A. Hopkins,
G. Hechenblaikner,
N. L. Smith,
C. J. Foot
Abstract:
We have observed a superfluid gyroscope effect in a dilute gas Bose-Einstein condensate. A condensate with a vortex possesses a single quantum of angular momentum and this causes the plane of oscillation of the scissors mode to precess around the vortex line. We have measured the precession rate of the scissors oscillation. From this we deduced the angular momentum associated with the vortex lin…
▽ More
We have observed a superfluid gyroscope effect in a dilute gas Bose-Einstein condensate. A condensate with a vortex possesses a single quantum of angular momentum and this causes the plane of oscillation of the scissors mode to precess around the vortex line. We have measured the precession rate of the scissors oscillation. From this we deduced the angular momentum associated with the vortex line and found a value close to $\hbar$ per particle, as predicted for a superfluid.
△ Less
Submitted 27 September, 2002;
originally announced September 2002.
-
The Moment of Inertia and the Scissors Mode of a Bose-condensed Gas
Authors:
O. M. Marago',
G. Hechenblaikner,
E. Hodby,
S. A. Hopkins,
C. J. Foot
Abstract:
We relate the frequency of the scissors mode to the moment of inertia of a trapped Bose gas at finite temperature in a semi-classical approximation. We apply these theoretical results to the data obtained in our previous study of the properties of the scissors mode of a trapped Bose-Einstein condensate of $^{87}$Rb atoms as a function of the temperature. The frequency shifts that we measured sho…
▽ More
We relate the frequency of the scissors mode to the moment of inertia of a trapped Bose gas at finite temperature in a semi-classical approximation. We apply these theoretical results to the data obtained in our previous study of the properties of the scissors mode of a trapped Bose-Einstein condensate of $^{87}$Rb atoms as a function of the temperature. The frequency shifts that we measured show quenching of the moment of inertia of the Bose gas at temperatures below the transition temperature - the system has a lower moment of inertia that of a rigid body with the same mass distribution, because of superfluidity.
△ Less
Submitted 11 September, 2001;
originally announced September 2001.
-
Vortex nucleation in Bose-Einstein condensates in an oblate, purely magnetic potential
Authors:
E. Hodby,
G. Hechenblaikner,
S. A. Hopkins,
O. M. Maragò,
C. J. Foot
Abstract:
We have investigated the formation of vortices by rotating the purely magnetic potential confining a Bose-Einstein condensate. We modified the bias field of an axially symmetric TOP trap to create an elliptical potential that rotates in the radial plane. This enabled us to study the conditions for vortex nucleation over a wide range of eccentricities and rotation rates.
We have investigated the formation of vortices by rotating the purely magnetic potential confining a Bose-Einstein condensate. We modified the bias field of an axially symmetric TOP trap to create an elliptical potential that rotates in the radial plane. This enabled us to study the conditions for vortex nucleation over a wide range of eccentricities and rotation rates.
△ Less
Submitted 13 June, 2001;
originally announced June 2001.
-
Direct observation of irrotational flow and evidence of superfluidity in a rotating Bose-Einstein condensate
Authors:
G. Hechenblaikner,
E. Hodby,
S. A. Hopkins,
O. M. Marago',
C. J. Foot
Abstract:
We observed the expansion of vortex-free Bose-condensates after their sudden release from a slowly rotating anisotropic trap. Our results show clear experimental evidence of the irrotational flow expected for a superfluid. The expansion from a rotating trap has strong features associated with the superfluid nature of a Bose-condensate, namely that the condensate cannot at any point be cylindrica…
▽ More
We observed the expansion of vortex-free Bose-condensates after their sudden release from a slowly rotating anisotropic trap. Our results show clear experimental evidence of the irrotational flow expected for a superfluid. The expansion from a rotating trap has strong features associated with the superfluid nature of a Bose-condensate, namely that the condensate cannot at any point be cylindrically symmetric with respect to the axis of rotation since such a wavefunction cannot possess angular momentum. Consequently, an initially rotating condensate expands in a distinctively different way to one released from a static trap. We report measurements of this phenomenon in absorption images of the condensate taken along the direction of the rotation axis.
△ Less
Submitted 9 June, 2001;
originally announced June 2001.
-
Calculation of mode coupling for quadrupole excitations in a Bose-Einstein condensate
Authors:
G. Hechenblaikner,
S. A. Morgan,
E. Hodby,
O. M. Marago,
C. J. Foot
Abstract:
In this paper we give a theoretical description of resonant coupling between two collective excitations of a Bose condensed gas (BEC) on, or close, to a second harmonic resonance. Using analytic expressions for the quasi-particle wavefunctions we show that the coupling between quadrupole modes is strong, leading to a coupling time of a few milliseconds (for a TOP trap with radial frequency 100 H…
▽ More
In this paper we give a theoretical description of resonant coupling between two collective excitations of a Bose condensed gas (BEC) on, or close, to a second harmonic resonance. Using analytic expressions for the quasi-particle wavefunctions we show that the coupling between quadrupole modes is strong, leading to a coupling time of a few milliseconds (for a TOP trap with radial frequency 100 Hz and 10^4 atoms). Using the hydrodynamic approximation, we derive analytic expression for the coupling matrix element. These can be used with an effective Hamiltonian (that we also derive) to describe the dynamics of the coupling process and the associated squeezing effects.
△ Less
Submitted 21 May, 2001;
originally announced May 2001.
-
Temperature Dependence of Dam** and Frequency Shifts of the Scissors Mode of a trapped Bose-Einstein Condensate
Authors:
Onofrio Marago',
Gerald Hechenblaikner,
Eleanor Hodby,
Christopher Foot
Abstract:
We have studied the properties of the scissors mode of a trapped Bose-Einstein condensate of $^{87}$Rb atoms at finite temperature. We measured a significant shift in the frequency of the mode below the hydrodynamic limit and a strong dependence of the dam** rate as the temperature increased. We compared our dam** rate results to recent theoretical calculations for other observed collective…
▽ More
We have studied the properties of the scissors mode of a trapped Bose-Einstein condensate of $^{87}$Rb atoms at finite temperature. We measured a significant shift in the frequency of the mode below the hydrodynamic limit and a strong dependence of the dam** rate as the temperature increased. We compared our dam** rate results to recent theoretical calculations for other observed collective modes finding a fair agreement. From the frequency measurements we deduce the moment of inertia of the gas and show that it is quenched below the transition point, because of the superfluid nature of the condensed gas.
△ Less
Submitted 12 March, 2001; v1 submitted 15 January, 2001;
originally announced January 2001.
-
The experimental observation of Beliaev dam** in a Bose condensed gas
Authors:
E. Hodby,
O. M. Marago',
G. Hechenblaikner,
C. J. Foot
Abstract:
We report the first experimental observation of Beliaev dam** of a collective excitation in a Bose-condensed gas. Beliaev dam** is not predicted by the Gross-Pitaevskii equation and so this is one of the few experiments that tests BEC theory beyond the mean field approximation. Measurements of the amplitude of a high frequency scissors mode, show that the Beliaev process transfers energy to…
▽ More
We report the first experimental observation of Beliaev dam** of a collective excitation in a Bose-condensed gas. Beliaev dam** is not predicted by the Gross-Pitaevskii equation and so this is one of the few experiments that tests BEC theory beyond the mean field approximation. Measurements of the amplitude of a high frequency scissors mode, show that the Beliaev process transfers energy to a lower lying mode and then back and forth between these modes. These characteristics are quite distinct from those of Landau dam**, which leads to a monotonic decrease in amplitude. To enhance the Beliaev process we adjusted the geometry of the magnetic trap** potential to give a frequency ratio of 2 to 1 between two of the scissors modes of the condensate. The ratios of the trap oscillation frequencies $ω_y / ω_x$ and $ω_z / ω_x$ were changed independently, so that we could investigate the resonant coupling over a range of conditions.
△ Less
Submitted 11 October, 2000;
originally announced October 2000.
-
Bose-Einstein condensation in a stiff TOP trap with adjustable geometry
Authors:
E. Hodby,
G. Hechenblaikner,
O. M. Marago',
J. Arlt,
S. Hopkins,
C. J. Foot
Abstract:
We report on the realisation of a stiff magnetic trap with independently adjustable trap frequencies, $ω_z$ and $ω_r$, in the axial and radial directions respectively. This has been achieved by applying an axial modulation to a Time-averaged Orbiting Potential (TOP) trap. The frequency ratio of the trap, $ω_z / ω_r$, can be decreased continuously from the original TOP trap value of 2.83 down to…
▽ More
We report on the realisation of a stiff magnetic trap with independently adjustable trap frequencies, $ω_z$ and $ω_r$, in the axial and radial directions respectively. This has been achieved by applying an axial modulation to a Time-averaged Orbiting Potential (TOP) trap. The frequency ratio of the trap, $ω_z / ω_r$, can be decreased continuously from the original TOP trap value of 2.83 down to 1.6. We have transferred a Bose-Einstein condensate (BEC) into this trap and obtained very good agreement between its observed anisotropic expansion and the hydrodynamic predictions. Our method can be extended to obtain a spherical trap** potential, which has a geometry of particular theoretical interest.
△ Less
Submitted 3 April, 2000;
originally announced April 2000.
-
Observation of harmonic generation and nonlinear coupling in the collective dynamics of a Bose condensate
Authors:
G. Hechenblaikner,
O. M. Marago',
E. Hodby,
J. Arlt,
S. Hopkins,
C. J. Foot
Abstract:
We report the observation of harmonic generation and strong nonlinear coupling of two collective modes of a condensed gas of rubidium atoms. Using a modified TOP trap we changed the trap anisotropy to a value where the frequency of the m=0 high-lying mode corresponds to twice the frequency of the m=0 low-lying mode, thus leading to strong nonlinear coupling between these modes. By changing the a…
▽ More
We report the observation of harmonic generation and strong nonlinear coupling of two collective modes of a condensed gas of rubidium atoms. Using a modified TOP trap we changed the trap anisotropy to a value where the frequency of the m=0 high-lying mode corresponds to twice the frequency of the m=0 low-lying mode, thus leading to strong nonlinear coupling between these modes. By changing the anisotropy of the trap and exciting the low-lying mode we observed significant frequency shifts of this fundamental mode and also the generation of its second harmonic.
△ Less
Submitted 30 March, 2000;
originally announced March 2000.
-
Bose-Einstein condensation in a rotating anisotropic TOP trap
Authors:
J. Arlt,
O. Marago',
E. Hodby,
S. A. Hopkins,
G. Hechenblaikner,
S. Webster,
C. J. Foot
Abstract:
We describe the construction and operation of a time-orbiting potential trap (TOP trap) that has different oscillation frequencies along its three principal axes. These axes can be rotated and we have observed Bose-Einstein condensates of 87^Rb with a rotating ellipsoidal shape. Under these conditions it has been predicted that quantized vortices form and are stable.
We describe the construction and operation of a time-orbiting potential trap (TOP trap) that has different oscillation frequencies along its three principal axes. These axes can be rotated and we have observed Bose-Einstein condensates of 87^Rb with a rotating ellipsoidal shape. Under these conditions it has been predicted that quantized vortices form and are stable.
△ Less
Submitted 12 November, 1999;
originally announced November 1999.
-
Observation of the scissors mode and superfluidity of a trapped Bose-Einstein condensed gas
Authors:
O. M. Marago',
S. A. Hopkins,
J. Arlt,
E. Hodby,
G. Hechenblaikner,
C. J. Foot
Abstract:
We report the observation of the scissors mode of a Bose-Einstein condensed gas of 87^Rb atoms in a magnetic trap, which gives direct evidence of superfluidity in this system. The scissors mode of oscillation is excited by a sudden rotation of the anisotropic trap** potential. For a gas above T_c (normal fluid) we detect the occurrence of oscillations at two frequencies, with the lower frequen…
▽ More
We report the observation of the scissors mode of a Bose-Einstein condensed gas of 87^Rb atoms in a magnetic trap, which gives direct evidence of superfluidity in this system. The scissors mode of oscillation is excited by a sudden rotation of the anisotropic trap** potential. For a gas above T_c (normal fluid) we detect the occurrence of oscillations at two frequencies, with the lower frequency corresponding to the rigid body value of the moment of inertia. Well below T_c the condensate oscillates at a single frequency, without dam**, as expected for a superfluid.
△ Less
Submitted 12 November, 1999;
originally announced November 1999.