Showing 1–14 of 14 results for author: Hati, A

10 GHz Generation with Ultra-Low Phase Noise via the Transfer Oscillator Technique

Authors: Nicholas V. Nardelli, Tara M. Fortier, Marco Pomponio, Esther Baumann, Craig Nelson, Thomas R. Schibli, Archita Hati

Abstract: Coherent frequency division of high-stability optical sources permits the extraction of microwave signals with ultra-low phase noise, enabling their application to systems with stringent timing precision. To date, the highest performance systems have required tight phase stabilization of laboratory grade optical frequency combs to Fabry-Perot optical reference cavities for faithful optical-to-micr… ▽ More Coherent frequency division of high-stability optical sources permits the extraction of microwave signals with ultra-low phase noise, enabling their application to systems with stringent timing precision. To date, the highest performance systems have required tight phase stabilization of laboratory grade optical frequency combs to Fabry-Perot optical reference cavities for faithful optical-to-microwave frequency division. This requirement limits the technology to highly-controlled laboratory environments. Here, we employ a transfer oscillator technique, which employs digital and RF analog electronics to coherently suppress additive optical frequency comb noise. This relaxes the stabilization requirements and allows for the extraction of multiple independent microwave outputs from a single comb, while at the same time, permitting low-noise microwave generation from combs with higher noise profiles. Using this method we transferred the phase stability of two high-Finesse optical sources at 1157 nm and 1070 nm to two independent 10 GHz signals using a single frequency comb. We demonstrated absolute phase noise below -106 dBc/Hz at 1-Hz from carrier with corresponding 1 second fractional frequency instability below $2\times10^{-15}$. Finally, the latter phase noise levels were attainable for comb linewidths broadened up to 2 MHz, demonstrating the potential for out-of lab use with low SWaP lasers. △ Less

Submitted 1 October, 2021; originally announced October 2021.

Weakly Supervised Geodesic Segmentation of Egyptian Mummy CT Scans

Authors: Avik Hati, Matteo Bustreo, Diego Sona, Vittorio Murino, Alessio Del Bue

Abstract: In this paper, we tackle the task of automatically analyzing 3D volumetric scans obtained from computed tomography (CT) devices. In particular, we address a particular task for which data is very limited: the segmentation of ancient Egyptian mummies CT scans. We aim at digitally unwrap** the mummy and identify different segments such as body, bandages and jewelry. The problem is complex because… ▽ More In this paper, we tackle the task of automatically analyzing 3D volumetric scans obtained from computed tomography (CT) devices. In particular, we address a particular task for which data is very limited: the segmentation of ancient Egyptian mummies CT scans. We aim at digitally unwrap** the mummy and identify different segments such as body, bandages and jewelry. The problem is complex because of the lack of annotated data for the different semantic regions to segment, thus discouraging the use of strongly supervised approaches. We, therefore, propose a weakly supervised and efficient interactive segmentation method to solve this challenging problem. After segmenting the wrapped mummy from its exterior region using histogram analysis and template matching, we first design a voxel distance measure to find an approximate solution for the body and bandage segments. Here, we use geodesic distances since voxel features as well as spatial relationship among voxels is incorporated in this measure. Next, we refine the solution using a GrabCut based segmentation together with a tracking method on the slices of the scan that assigns labels to different regions in the volume, using limited supervision in the form of scribbles drawn by the user. The efficiency of the proposed method is demonstrated using visualizations and validated through quantitative measures and qualitative unwrap** of the mummy. △ Less

Submitted 17 April, 2020; originally announced April 2020.

Cross-spectrum noise measurements at 4 K to minimize power-splitter anti-correlation effect

Authors: Archita Hati, Craig W. Nelson, David Pappas, David A. Howe

Abstract: We report an accurate measurement of the phase noise of a thermally limited electronic oscillator at 300 K. By thermally limited we mean that the white signal-to-noise ratio of the oscillator is at or near the level generated by the thermal noise of the 50 ohm source resistor. The measurement is devoid of the anti-correlation effect that originates from the common mode power splitter in a cross-sp… ▽ More We report an accurate measurement of the phase noise of a thermally limited electronic oscillator at 300 K. By thermally limited we mean that the white signal-to-noise ratio of the oscillator is at or near the level generated by the thermal noise of the 50 ohm source resistor. The measurement is devoid of the anti-correlation effect that originates from the common mode power splitter in a cross-spectrum technique. The anti-correlation effect is mitigated by cooling the power splitter to a liquid helium temperature (4 K). The measurements in this paper are the first proof of theoretical claims that additive thermal noise from the splitter can be reduced significantly with cryogenic cooling and this can eliminate any anti-correlated noise introduced by use of the two-channel cross-spectrum technique. We also confirm measurements of partial anti-correlation error of (-1.3 +/- 0.6) dB that agree with theory when the splitter is at liquid nitrogen temperature of 77 K. △ Less

Submitted 11 January, 2017; originally announced January 2017.

Comments: 8 pages, 6 figures

Cross-spectrum Measurement of Thermal-noise Limited Oscillators

Authors: Archita Hati, Craig W. Nelson, David A. Howe

Abstract: Cross-spectrum analysis is a commonly-used technique for the detection of phase and amplitude noise of a signal in the presence of interfering noise. It extracts the desired correlated noise from two time series in the presence of uncorrelated interfering noise. Recently, we demonstrated that the phase-inversion (anti-correlation) effect due to AM noise leakage can cause complete or partial collap… ▽ More Cross-spectrum analysis is a commonly-used technique for the detection of phase and amplitude noise of a signal in the presence of interfering noise. It extracts the desired correlated noise from two time series in the presence of uncorrelated interfering noise. Recently, we demonstrated that the phase-inversion (anti-correlation) effect due to AM noise leakage can cause complete or partial collapse of the cross-spectral function. In this paper, we discuss the newly discovered effect of anti-correlated thermal noise that originates from the common-mode power divider (splitter), an essential component in a cross-spectrum noise measurement system. We studied this effect for different power splitters and discuss its influence on the measurement of thermal-noise limited oscillators. An oscillator whose thermal noise is primarily set by the 50 ohm source resistance is referred to as a thermally-limited oscillator. We provide theory, simulation and experimental results. In addition, we expand this study to reveal how the presence of ferrite-isolators and amplifiers at the output ports of the power splitters can affect the oscillator noise measurements. Finally, we discuss a possible solution to overcome this problem. △ Less

Submitted 18 December, 2015; originally announced December 2015.

Digital-photonic synthesis of ultra-low noise tunable signals from RF to 100 GHz

Authors: T. M. Fortier, A. Rolland, F. Quinlan, F. N. Baynes, A. J. Metcalf, A. Hati, A. Ludlow, N. Hinkley, M. Shimizu, T. Ishibashi, J. C. Campbell, S. A. Diddams

Abstract: The demand for higher data rates and better synchronization in communication and navigation systems necessitates the development of new wideband and tunable sources with noise performance exceeding that provided by traditional oscillators and synthesizers. Precision synthesis is paramount for providing frequency references and timing in a broad range of applications including next-generation telec… ▽ More The demand for higher data rates and better synchronization in communication and navigation systems necessitates the development of new wideband and tunable sources with noise performance exceeding that provided by traditional oscillators and synthesizers. Precision synthesis is paramount for providing frequency references and timing in a broad range of applications including next-generation telecommunications, high precision measurement, and radar and sensing. Here we describe a digital-photonic synthesizer (DPS) based on optical frequency division that enables the generation of widely tunable signals from near DC to 100 GHz with a fractional frequency instability of 1 part in 10^15. The spectral purity of the DPS derived signals represents an improvement in close-to-carrier noise performance over the current state-of-the-art of nearly 7 orders of magnitude in the W-band (100 GHz), and up to 5 orders of magnitude in the X-band (10 GHz). △ Less

Submitted 10 June, 2015; originally announced June 2015.

An integrated low phase noise radiation-pressure-driven optomechanical oscillator chipset

Authors: X. Luan, Y. Huang, Y. Li, J. F. McMillan, J. Zheng, S. -W. Huang, P. -C. Hsieh, T. Gu, D. Wang, A. Hati, D. A. Howe, G. Wen, M. Yu, G. Lo, D. -L. Kwong, C. W. Wong

Abstract: High-quality frequency references are the cornerstones in position, navigation and timing applications of both scientific and commercial domains. Optomechanical oscillators, with direct coupling to continuous-wave light and non-material-limited f Q product, are long regarded as a potential platform for frequency reference in radio-frequency-photonic architectures. However, one major challenge is t… ▽ More High-quality frequency references are the cornerstones in position, navigation and timing applications of both scientific and commercial domains. Optomechanical oscillators, with direct coupling to continuous-wave light and non-material-limited f Q product, are long regarded as a potential platform for frequency reference in radio-frequency-photonic architectures. However, one major challenge is the compatibility with standard CMOS fabrication processes while maintaining optomechanical high quality performance. Here we demonstrate the monolithic integration of photonic crystal optomechanical oscillators and on-chip high speed Ge detectors based on the silicon CMOS platform. With the generation of both high harmonics (up to 59th order) and subharmonics (down to 1/4), our chipset provides multiple frequency tones for applications in both frequency multipliers and dividers. The phase noise is measured down to -125 dBc/Hz at 10 kHz offset at ~ 400 μW dropped-in powers, one of the lowest noise optomechanical oscillators to date and in room-temperature and atmospheric non-vacuum operating conditions. These characteristics enable optomechanical oscillators as a frequency reference platform for radio-frequency-photonic information processing. △ Less

Submitted 21 October, 2014; originally announced October 2014.

Comments: 32 pages, 13 figures

Report number: SREP-14-04242

PM noise Measurement at W-Band

Authors: A. Hati, C. W. Nelson, D. A. Howe

Abstract: We present improved performance for a 92 to 96 GHz cross-spectrum phase modulated (PM) noise measurement system reported. The system is principally designed to measure amplifiers in pulsed mode as well as in CW mode at a given pulse repetition frequency. This paper reports only the CW mode of operation. Data for the noise-floor of the measurement system as well as PM noise of several W- band activ… ▽ More We present improved performance for a 92 to 96 GHz cross-spectrum phase modulated (PM) noise measurement system reported. The system is principally designed to measure amplifiers in pulsed mode as well as in CW mode at a given pulse repetition frequency. This paper reports only the CW mode of operation. Data for the noise-floor of the measurement system as well as PM noise of several W- band active components are presented. This work also discusses an improved performance frequency synthesizer that operates in the 92 to 96 GHz range. △ Less

Submitted 28 May, 2014; originally announced May 2014.

PM noise of a 40 GHz air-dielectric cavity oscillator

Authors: Archita Hati, Craig W. Nelson, B. Riddle, David A. Howe

Abstract: We describe the design of a low-phase-modulated (PM) noise, 40 GHz oscillator that uses a conventional air-dielectric cavity resonator as a frequency discriminator to improve the PM noise of a commercial 10 GHz dielectric resonator oscillator (DRO) frequency multiplied by four. The main features of this design incorporate (1) unloaded cavity quality factor (Q) of 30,000, (2) high coupling coeffici… ▽ More We describe the design of a low-phase-modulated (PM) noise, 40 GHz oscillator that uses a conventional air-dielectric cavity resonator as a frequency discriminator to improve the PM noise of a commercial 10 GHz dielectric resonator oscillator (DRO) frequency multiplied by four. The main features of this design incorporate (1) unloaded cavity quality factor (Q) of 30,000, (2) high coupling coefficient, (3) large carrier suppression by use of interferometric signal processing, (4) large operating signal power of approximately 1 watt (W), and (5) relatively small size. In addition, we report the PM noise of several Ka-band components. △ Less

Submitted 18 April, 2014; originally announced April 2014.

Operation of an optically coherent frequency comb outside the metrology lab

Authors: Laura C. Sinclair, Ian Coddington, William C. Swann, Greg B. Rieker, Archita Hati, Kana Iwakuni, Nathan R. Newbury

Abstract: We demonstrate a self-referenced fiber frequency comb that can operate outside the well-controlled optical laboratory. The frequency comb has residual optical linewidths of < 1 Hz, sub-radian residual optical phase noise, and residual pulse-to-pulse timing jitter of 2.4 - 5 fs, when locked to an optical reference. This fully phase-locked frequency comb has been successfully operated in a moving ve… ▽ More We demonstrate a self-referenced fiber frequency comb that can operate outside the well-controlled optical laboratory. The frequency comb has residual optical linewidths of < 1 Hz, sub-radian residual optical phase noise, and residual pulse-to-pulse timing jitter of 2.4 - 5 fs, when locked to an optical reference. This fully phase-locked frequency comb has been successfully operated in a moving vehicle with 0.5 g peak accelerations and on a shaker table with a sustained 0.5 g rms integrated acceleration, while retaining its optical coherence and 5-fs-level timing jitter. This frequency comb should enable metrological measurements outside the laboratory with the precision and accuracy that are the hallmarks of comb-based systems. Work of the U.S. government, not subject to copyright △ Less

Submitted 20 December, 2013; originally announced December 2013.

Phase inversion and collapse of the cross-spectral function

Authors: Craig W. Nelson, Archita Hati, David A. Howe

Abstract: Cross-spectral analysis is a mathematical tool for extracting the power spectral density of a correlated signal from two time series in the presence of uncorrelated interfering signals. We demonstrate and explain a set of conditions where the detection of the desired signal using cross-spectral fails partially or entirely in the presence of a second uncorrelated signal. Not understanding when and… ▽ More Cross-spectral analysis is a mathematical tool for extracting the power spectral density of a correlated signal from two time series in the presence of uncorrelated interfering signals. We demonstrate and explain a set of conditions where the detection of the desired signal using cross-spectral fails partially or entirely in the presence of a second uncorrelated signal. Not understanding when and how this effect occurs can lead to dramatic underreporting of the desired signal. Theoretical, simulated and experimental demonstrations of this effect as well as mitigating methods are presented. △ Less

Submitted 24 July, 2013; originally announced July 2013.

Feedback and harmonic locking of slot-type optomechanical oscillators to external low-noise reference clocks

Authors: Jiangjun Zheng, Ying Li, Noam Goldberg, Mickey McDonald, Xingsheng Luan, Archita Hati, Ming Lu, Stefan Strauf, Tanya Zelevinsky, David A. Howe, Chee Wei Wong

Abstract: We demonstrate feedback and harmonic locking of chip-scale slot-type optomechanical oscillators to external low-noise reference clocks, with suppressed timing jitter by three orders of magnitude. The feedback and compensation techniques significantly reduce the close-to-carrier phase noise, especially within the locking bandwidth for the integral root-mean-square timing jitter. Harmonic locking vi… ▽ More We demonstrate feedback and harmonic locking of chip-scale slot-type optomechanical oscillators to external low-noise reference clocks, with suppressed timing jitter by three orders of magnitude. The feedback and compensation techniques significantly reduce the close-to-carrier phase noise, especially within the locking bandwidth for the integral root-mean-square timing jitter. Harmonic locking via high-order carrier signals is also demonstrated with similar phase noise and integrated root-mean-square timing jitter reduction. The chip-scale optomechanical oscillators are tunable over an 80-kHz range by tracking the reference clock, with potential applications in tunable radio-frequency photonics platforms. △ Less

Submitted 8 March, 2013; originally announced March 2013.

Photonic microwave generation with high-power photodiodes

Authors: Tara M. Fortier, Franklyn Quinlan, Archita Hati, Craig Nelson, Jennifer A. Taylor, Yang Fu, Joe Campbell, Scott A. Diddams

Abstract: We utilize and characterize high-power, high-linearity modified uni-traveling carrier (MUTC) photodiodes for low-phase-noise photonic microwave generation based on optical frequency division. When illuminated with picosecond pulses from a repetition-rate-multiplied gigahertz Ti:sapphire modelocked laser, the photodiodes can achieve 10 GHz signal power of +14 dBm. Using these diodes, a 10 GHz micro… ▽ More We utilize and characterize high-power, high-linearity modified uni-traveling carrier (MUTC) photodiodes for low-phase-noise photonic microwave generation based on optical frequency division. When illuminated with picosecond pulses from a repetition-rate-multiplied gigahertz Ti:sapphire modelocked laser, the photodiodes can achieve 10 GHz signal power of +14 dBm. Using these diodes, a 10 GHz microwave tone is generated with less than 500 attoseconds absolute integrated timing jitter (1 Hz-10 MHz) and a phase noise floor of -177 dBc/Hz. We also characterize the electrical response, amplitude-to-phase conversion, saturation and residual noise of the MUTC photodiodes. △ Less

Submitted 24 February, 2013; originally announced February 2013.

Comments: 3 pages, 3 figures

Sub-femtosecond absolute timing precision with a 10 GHz hybrid photonic-microwave oscillator

Authors: T. M. Fortier, C. W. Nelson, A. Hati, F. Quinlan, J. Taylor, H. Jiang, C. W. Chou, T. Rosenband, N. Lemke, A. Ludlow, D. Howe, C. W. Oates, S. A. Diddams

Abstract: We present an optical-electronic approach to generating microwave signals with high spectral purity. By circumventing shot noise and operating near fundamental thermal limits, we demonstrate 10 GHz signals with an absolute timing jitter for a single hybrid oscillator of 420 attoseconds (1Hz - 5 GHz). We present an optical-electronic approach to generating microwave signals with high spectral purity. By circumventing shot noise and operating near fundamental thermal limits, we demonstrate 10 GHz signals with an absolute timing jitter for a single hybrid oscillator of 420 attoseconds (1Hz - 5 GHz). △ Less

Submitted 5 May, 2012; originally announced May 2012.

Journal ref: Applied Physics Letters 100, 231111 (2012)

Characterization of Power-to-Phase Conversion in High-Speed P-I-N Photodiodes

Authors: J. Taylor, S. Datta, A. Hati, C. Nelson, F. Quinlan, A. Joshi, S. Diddams

Abstract: Fluctuations of the optical power incident on a photodiode can be converted into phase fluctuations of the resulting electronic signal due to nonlinear saturation in the semiconductor. This impacts overall timing stability (phase noise) of microwave signals generated from a photodetected optical pulse train. In this paper, we describe and utilize techniques to characterize this conversion of ampli… ▽ More Fluctuations of the optical power incident on a photodiode can be converted into phase fluctuations of the resulting electronic signal due to nonlinear saturation in the semiconductor. This impacts overall timing stability (phase noise) of microwave signals generated from a photodetected optical pulse train. In this paper, we describe and utilize techniques to characterize this conversion of amplitude noise to phase noise for several high-speed (>10 GHz) InGaAs P-I-N photodiodes operated at 900 nm. We focus on the impact of this effect on the photonic generation of low phase noise 10 GHz microwave signals and show that a combination of low laser amplitude noise, appropriate photodiode design, and optimum average photocurrent is required to achieve phase noise at or below -100 dBc/Hz at 1 Hz offset a 10 GHz carrier. In some photodiodes we find specific photocurrents where the power-to-phase conversion factor is observed to go to zero. △ Less

Submitted 12 February, 2011; originally announced February 2011.

Journal ref: IEEE Photonics Journal, Vol 3, Feb. 2011, pages 140 - 151