-
Double-GEM based thermal neutron detector prototype
Authors:
L. A. Serra Filho,
R. Felix dos Santos,
G. G. A. de Souza,
M. M. M. Paulino,
F. A. Souza,
M. Moralles,
H. Natal da Luz,
M. Bregant,
M. G. Munhoz,
Chung-Chuan Lai,
Carina Höglund,
Per-Olof Svensson,
Linda Robinson,
Richard Hall-Wilton
Abstract:
The Helium-3 shortage and the growing interest in neutron science constitute a driving factor in develo** new neutron detection technologies. In this work, we report the development of a double-GEM detector prototype that uses a $^{10}$B$_4$C layer as a neutron converter material. GEANT4 simulations were performed predicting an efficiency of 3.14(10) %, agreeing within 2.7 $σ$ with the experimen…
▽ More
The Helium-3 shortage and the growing interest in neutron science constitute a driving factor in develo** new neutron detection technologies. In this work, we report the development of a double-GEM detector prototype that uses a $^{10}$B$_4$C layer as a neutron converter material. GEANT4 simulations were performed predicting an efficiency of 3.14(10) %, agreeing within 2.7 $σ$ with the experimental and analytic detection efficiencies obtained by the detector when tested in a 41.8 meV thermal neutron beam. The detector is position sensitive, equipped with a 256+256 strip readout connected to resistive chains, and achieves a spatial resolution better than 3 mm. The gain stability over time was also measured with a fluctuation of about 0.2 %h$^{-1}$ of the signal amplitude. A simple data acquisition with only 5 electronic channels is sufficient to operate this detector.
△ Less
Submitted 19 July, 2022; v1 submitted 14 May, 2022;
originally announced May 2022.
-
Effect of substrate roughness and material selection on the microstructure of sputtering deposited boron carbide thin films
Authors:
Chung-Chuan Lai,
Robert Boyd,
Per-Olof Svensson,
Carina Höglund,
Linda Robinson,
Jens Birch,
Richard Hall-Wilton
Abstract:
Amorphous boron carbide (B4C) thin films are by far the most popular form for the neutron converting layers in the 10B-based neutron detectors, which are a rising trend in detector technologies in response to the increasing scarcity and price of 3He, the standard material for neutron detection. The microstructure of the B4C films is closely related to the important properties, e.g. density and adh…
▽ More
Amorphous boron carbide (B4C) thin films are by far the most popular form for the neutron converting layers in the 10B-based neutron detectors, which are a rising trend in detector technologies in response to the increasing scarcity and price of 3He, the standard material for neutron detection. The microstructure of the B4C films is closely related to the important properties, e.g. density and adhesion, for the converting layers, which eventually affect the detection efficiency and the long-term stability of the detectors. To study the influence from substrates of different roughness and materials, the B4C films were deposited on polished Si substrates with Al, Ti, and Cu buffer layers and unpolished Si, Al, Ti, and Cu substrates by direct current magnetron sputtering at a substrate temperature of 623 K. The tapered columnar grains and nodular defects, generally observed in SEM images, indicated a strong shadowing effect where voids were introduced around the grains. The change in the grain size did not show a direct dependence to the substrate roughness, acquired from the surface profile, nor to the mass density of the films, obtained from reflectivity patterns. However, films with non-uniform size of columnar grains were deposited on substrates with high skewness, leading to a drop of mass density from ~95 % down to ~70 % of tabulated bulk density. On the other hand, similar microstructures and mass density were obtained from the films deposited on Al, Ti, and Cu of different roughness and good adhesion were observed from cross-cut adhesion tests, showing the reliability of sputtering deposited B4C films on common structural materials in neutron detectors.
△ Less
Submitted 29 January, 2022;
originally announced January 2022.
-
Statistical position reconstruction for RPC-based thermal neutron detectors
Authors:
A. Morozov,
L. M. S. Margato,
V. Solovov,
A. Blanco,
J. Saraiva,
T. Wilpert,
K. Zeitelhack,
K. Roemer,
C. Höglund,
L. Robinson,
R. Hall-Wilton
Abstract:
Multilayer position-sensitive 10B-RPC thermal neutron detectors offer an attractive combination of sub-millimeter spatial resolution and high (>50%) detection efficiency. Here we describe a new position reconstruction method based on a statistical approach. Using experimental data, we compare the performance of this method with that of the centroid reconstruction. Both methods result in a similar…
▽ More
Multilayer position-sensitive 10B-RPC thermal neutron detectors offer an attractive combination of sub-millimeter spatial resolution and high (>50%) detection efficiency. Here we describe a new position reconstruction method based on a statistical approach. Using experimental data, we compare the performance of this method with that of the centroid reconstruction. Both methods result in a similar image linearity/uniformity and spatial resolution. However, the statistical method allows to improve the image quality at the detector periphery, offers more flexible event filtering and allows to develop automatic quality monitoring procedures for early detection of situations when a change in the detector operation conditions starts to affect reconstruction quality.
△ Less
Submitted 26 July, 2021; v1 submitted 28 May, 2021;
originally announced May 2021.
-
Towards high-rate RPC-based thermal neutron detectors using low-resistivity electrodes
Authors:
L. M. S. Margato,
A. Morozov,
A. Blanco,
P. Fonte,
L. Lopes,
J. Saraiva,
K. Zeitelhack,
R. Hall-Wilton,
C. Höglund,
L. Robinson,
P. Svensson,
L. Naumann,
K. Roemer,
D. Stach,
Th. Wilpert
Abstract:
We present experimental results on the counting rate measurements for several single-gap $^{10}$B lined resistive plate chambers ($^{10}$B-RPCs) with anodes made from standard float glass, low resistivity glass and ceramic. The measurements were performed at the V17 monochromatic neutron beamline (3.35 Ȧ) at the Helmholtz-Zentrum Berlin. For the $^{10}$B-RPCs with 0.28 mm thick float glass a maxim…
▽ More
We present experimental results on the counting rate measurements for several single-gap $^{10}$B lined resistive plate chambers ($^{10}$B-RPCs) with anodes made from standard float glass, low resistivity glass and ceramic. The measurements were performed at the V17 monochromatic neutron beamline (3.35 Ȧ) at the Helmholtz-Zentrum Berlin. For the $^{10}$B-RPCs with 0.28 mm thick float glass a maximum counting rate density of about $8\times 10^{3}$ $Hz/cm^{2}$ was obtained. In the case of low resistivity glass and ceramic, the counting rate density did not deviate from linear dependence on the neutron flux up to the maximum flux available at this beamline and exceeded a value of $3\times 10^{4}$ $Hz/cm^{2}$.
△ Less
Submitted 1 April, 2021;
originally announced April 2021.
-
Time- and energy-resolved effects in the boron-10 based Multi-Grid and helium-3 based thermal neutron detectors
Authors:
A. Backis,
A. Khaplanov,
R. Al Jebali,
R. Ammer,
I. Apostolidis,
J. Birch,
C. -C. Lai,
P. P. Deen,
M. Etxegarai,
N. de Ruette,
J. Freita Ramos,
D. F. Förster,
E. Haettner,
R. Hall-Wilton,
D. Hamilton,
C. Höglund,
P. M. Kadletz,
K. Kanaki,
E. Karnickis,
O. Kirstein,
S. Kolya,
Z. Kraujalyte,
A. Laloni,
K. Livingston,
O. Löhman
, et al. (11 additional authors not shown)
Abstract:
The boron-10 based Multi-Grid detector is being developed as an alternative to helium-3 based neutron detectors. At the European Spallation Source, the detector will be used for time-of-flight neutron spectroscopy at cold to thermal neutron energies. The objective of this work is to investigate fine time- and energy-resolved effects of the Multi-Grid detector, down to a few $μ$eV, while comparing…
▽ More
The boron-10 based Multi-Grid detector is being developed as an alternative to helium-3 based neutron detectors. At the European Spallation Source, the detector will be used for time-of-flight neutron spectroscopy at cold to thermal neutron energies. The objective of this work is to investigate fine time- and energy-resolved effects of the Multi-Grid detector, down to a few $μ$eV, while comparing it to the performance of a typical helium-3 tube. Furthermore, it is to characterize differences between the detector technologies in terms of internal scattering, as well as the time reconstruction of ~ $μ$s short neutron pulses. The data were taken at the Helmholtz Zentrum Berlin, where the Multi-Grid detector and a helium-3 tube were installed at the ESS test beamline, V20. Using a Fermi-chopper, the neutron beam of the reactor was chopped into a few tens of $μ$s wide pulses before reaching the detector, located a few tens of cm downstream. The data of the measurements show an agreement between the derived and calculated neutron detection efficiency curve. The data also provide fine details on the effect of internal scattering, and how it can be reduced. For the first time, the chopper resolution was comparable to the timing resolution of the Multi-Grid detector. This allowed a detailed study of time- and energy resolved effects, as well as a comparison with a typical helium-3 tube.
△ Less
Submitted 14 January, 2021; v1 submitted 2 June, 2020;
originally announced June 2020.
-
Multilayer $^{10}B$-RPC neutron imaging detector
Authors:
L. M. S. Margato,
A. Morozov,
A. Blanco,
P. Fonte,
L. Lopes,
K. Zeitelhack,
R. Hall-Wilton,
C. Höglund,
L. Robinson,
S. Schmidt,
P. Svensson
Abstract:
Resistive plate chambers (RPC) lined with $^{10}B_{4}$C neutron converters is a promising cost effective technology for position-sensitive thermal neutron detection capable to outperform $^{3}$He-based detectors in terms of spatial resolution and timing. However, as for the other types of gaseous detectors with a single layer of $^{10}B_{4}$C at normal beam incidence, the detection efficiency to t…
▽ More
Resistive plate chambers (RPC) lined with $^{10}B_{4}$C neutron converters is a promising cost effective technology for position-sensitive thermal neutron detection capable to outperform $^{3}$He-based detectors in terms of spatial resolution and timing. However, as for the other types of gaseous detectors with a single layer of $^{10}B_{4}$C at normal beam incidence, the detection efficiency to thermal neutrons of a single-gap $^{10}B$-RPC is only about 6%. Aiming to overcome this limitation, we introduce a multi-layer $^{10}B$-RPCs detector with a stack of ten double-gap hybrid RPCs. A description of the detector design and the results of its characterization performed at the TREFF neutron beamline at the FRM II neutron facility are presented. The results demonstrate that the detection efficiency exceeds 60% for neutrons with a wavelength of 4.7 Å and the spatial resolution (FWHM) is about 0.25 mm and 0.35 mm in the X and Y direction, respectively.
△ Less
Submitted 26 May, 2020; v1 submitted 3 February, 2020;
originally announced February 2020.
-
Boron-10 lined RPCs for sub-millimeter resolution thermal neutron detectors: Feasibility study in a thermal neutron beam
Authors:
L. M. S. Margato,
A. Morozov,
A. Blanco,
P. Fonte,
F. A. F. Fraga,
B. Guerard,
R. Hall-Wilton,
C. Höglund,
A. Mangiarotti,
L. Robinson,
S. Schmidt,
K. Zeitelhack
Abstract:
The results of an experimental feasibility study of a position sensitive thermal neutron detector based on a resistive plate chamber (RPC) are presented. The detector prototype features a thin-gap (0.35 mm) hybrid RPC with an aluminium cathode lined with a 2 $μ$m thick $^{10}B{_4}C$ neutron converter layer enriched in $^{10}B$ and a float glass anode. A detection efficiency of ${\approx}$ 6.2…
▽ More
The results of an experimental feasibility study of a position sensitive thermal neutron detector based on a resistive plate chamber (RPC) are presented. The detector prototype features a thin-gap (0.35 mm) hybrid RPC with an aluminium cathode lined with a 2 $μ$m thick $^{10}B{_4}C$ neutron converter layer enriched in $^{10}B$ and a float glass anode. A detection efficiency of ${\approx}$ 6.2 ${\%}$ was measured for the neutron beam ($λ$ =2.5 $Å$) at normal incidence. A spatial resolution better than 0.5 mm FWHM was demonstrated.
△ Less
Submitted 25 September, 2018;
originally announced September 2018.
-
Neutron reflectometry with the Multi-Blade 10B-based detector
Authors:
G. Mauri,
F. Messi,
M. Anastasopoulos,
T. Arnold,
A. Glavic,
C. Höglund,
T. Ilves,
I. Lopez Higuera,
P. Pazmandi,
D. Raspino,
L. Robinson,
S. Schmidt,
P. Svensson,
D. Varga,
R. Hall-Wilton,
F. Piscitelli
Abstract:
The Multi-Blade is a Boron-10-based gaseous detector developed for neutron reflectometry instruments at the European Spallation Source (ESS) in Sweden. The main challenges for neutron reflectometry detectors are the instantaneous counting rate and spatial resolution. The Multi-Blade has been tested on the CRISP reflectometer at the ISIS neutron and muon source in UK. A campaign of scientific measu…
▽ More
The Multi-Blade is a Boron-10-based gaseous detector developed for neutron reflectometry instruments at the European Spallation Source (ESS) in Sweden. The main challenges for neutron reflectometry detectors are the instantaneous counting rate and spatial resolution. The Multi-Blade has been tested on the CRISP reflectometer at the ISIS neutron and muon source in UK. A campaign of scientific measurements has been performed to study the Multi-Blade response in real instrumental conditions. The results of these tests are discussed in this manuscript.
△ Less
Submitted 18 April, 2018; v1 submitted 11 April, 2018;
originally announced April 2018.
-
Characterization of the Multi-Blade 10B-based detector at the CRISP reflectometer at ISIS for neutron reflectometry at ESS
Authors:
F. Piscitelli,
G. Mauri,
F. Messi,
M. Anastasopoulos,
T. Arnold,
A. Glavic,
C. Höglund,
T. Ilves,
I. Lopez Higuera,
P. Pazmandi,
D. Raspino,
L. Robinson,
S. Schmidt,
P. Svensson,
D. Varga,
R. Hall-Wilton
Abstract:
The Multi-Blade is a Boron-10-based gaseous thermal neutron detector developed to face the challenge arising in neutron reflectometry at neutron sources. Neutron reflectometers are challenging instruments in terms of instantaneous counting rate and spatial resolution. This detector has been designed according to the requirements given by the reflectometers at the European Spallation Source (ESS) i…
▽ More
The Multi-Blade is a Boron-10-based gaseous thermal neutron detector developed to face the challenge arising in neutron reflectometry at neutron sources. Neutron reflectometers are challenging instruments in terms of instantaneous counting rate and spatial resolution. This detector has been designed according to the requirements given by the reflectometers at the European Spallation Source (ESS) in Sweden. The Multi-Blade has been installed and tested on the CRISP reflectometer at the ISIS neutron and muon source in UK. The results on the detailed detector characterization are discussed in this manuscript.
△ Less
Submitted 26 March, 2018;
originally announced March 2018.
-
Multi-Grid Detector for Neutron Spectroscopy: Results Obtained on Time-of-Flight Spectrometer CNCS
Authors:
M. Anastasopoulos,
R. Bebb,
K. Berry,
J. Birch,
T. Bryś,
J. -C. Buffet,
J. -F. Clergeau,
P. P. Deen,
G. Ehlers,
P. van Esch,
S. M. Everett,
B. Guerard,
R. Hall-Wilton,
K. Herwig,
L. Hultman,
C. Höglund,
I. Iruretagoiena,
F. Issa,
J. Jensen,
A. Khaplanov,
O. Kirstein,
I. Lopez-Higuera,
F. Piscitelli,
L. Robinson,
S. Schmidt
, et al. (1 additional authors not shown)
Abstract:
The Multi-Grid detector technology has evolved from the proof-of-principle and characterisation stages. Here we report on the performance of the Multi-Grid detector, the MG.CNCS prototype, which has been installed and tested at the Cold Neutron Chopper Spectrometer, CNCS at SNS. This has allowed a side-by-side comparison to the performance of $^3$He detectors on an operational instrument. The demo…
▽ More
The Multi-Grid detector technology has evolved from the proof-of-principle and characterisation stages. Here we report on the performance of the Multi-Grid detector, the MG.CNCS prototype, which has been installed and tested at the Cold Neutron Chopper Spectrometer, CNCS at SNS. This has allowed a side-by-side comparison to the performance of $^3$He detectors on an operational instrument. The demonstrator has an active area of 0.2 m$^2$. It is specifically tailored to the specifications of CNCS. The detector was installed in June 2016 and has operated since then, collecting neutron scattering data in parallel to the He-3 detectors of CNCS. In this paper, we present a comprehensive analysis of this data, in particular on instrument energy resolution, rate capability, background and relative efficiency. Stability, gamma-ray and fast neutron sensitivity have also been investigated. The effect of scattering in the detector components has been measured and provides input to comparison for Monte Carlo simulations. All data is presented in comparison to that measured by the $^3$He detectors simultaneously, showing that all features recorded by one detector are also recorded by the other. The energy resolution matches closely. We find that the Multi-Grid is able to match the data collected by $^3$He, and see an indication of a considerable advantage in the count rate capability. Based on these results, we are confident that the Multi-Grid detector will be capable of producing high quality scientific data on chopper spectrometers utilising the unprecedented neutron flux of the ESS.
△ Less
Submitted 3 April, 2017; v1 submitted 10 March, 2017;
originally announced March 2017.
-
The Multi-Blade Boron-10-based Neutron Detector for high intensity Neutron Reflectometry at ESS
Authors:
Francesco Piscitelli,
Francesco Messi,
Michail Anastasopoulos,
Tomasz Bryś,
Faye Chicken,
Eszter Dian,
Janos Fuzi,
Carina Höglund,
Gabor Kiss,
Janos Orban,
Peter Pazmandi,
Linda Robinson,
Laszlo Rosta,
Susann Schmidt,
Dezso Varga,
Tibor Zsiros,
Richard Hall-Wilton
Abstract:
The Multi-Blade is a Boron-10-based gaseous detector introduced to face the challenge arising in neutron reflectometry at pulsed neutron sources. Neutron reflectometers are the most challenging instruments in terms of instantaneous counting rate and spatial resolution. This detector has been designed to cope with the requirements set for the reflectometers at the upcoming European Spallation Sourc…
▽ More
The Multi-Blade is a Boron-10-based gaseous detector introduced to face the challenge arising in neutron reflectometry at pulsed neutron sources. Neutron reflectometers are the most challenging instruments in terms of instantaneous counting rate and spatial resolution. This detector has been designed to cope with the requirements set for the reflectometers at the upcoming European Spallation Source (ESS) in Sweden. Based on previous results obtained at the Institut Laue-Langevin (ILL) in France, an improved demonstrator has been built at ESS and tested at the Budapest Neutron Centre (BNC) in Hungary and at the Source Testing Facility (STF) at the Lund University in Sweden. A detailed description of the detector and the results of the tests are discussed in this manuscript.
△ Less
Submitted 26 January, 2017;
originally announced January 2017.
-
First Measurements with New High-Resolution Gadolinium-GEM Neutron Detectors
Authors:
Dorothea Pfeiffer,
Filippo Resnati,
Jens Birch,
Maddi Etxegarai,
Richard Hall-Wilton,
Carina Höglund,
Lars Hultman,
Isabel Llamas-Jansa,
Eraldo Oliveri,
Esko Oksanen,
Linda Robinson,
Leszek Ropelewski,
Susann Schmidt,
Christina Streli,
Patrik Thuiner
Abstract:
European Spallation Source instruments like the macromolecular diffractometer, NMX, require an excellent neutron detection efficiency, high-rate capabilities, time resolution, and an unprecedented spatial resolution in the order of a few hundred micrometers over a wide angular range of the incoming neutrons. For these instruments solid converters in combination with Micro Pattern Gaseous Detectors…
▽ More
European Spallation Source instruments like the macromolecular diffractometer, NMX, require an excellent neutron detection efficiency, high-rate capabilities, time resolution, and an unprecedented spatial resolution in the order of a few hundred micrometers over a wide angular range of the incoming neutrons. For these instruments solid converters in combination with Micro Pattern Gaseous Detectors (MPGDs) are a promising option. A GEM detector with gadolinium converter was tested on a cold neutron beam at the IFE research reactor in Norway. The μTPC analysis, proven to improve the spatial resolution in the case of $^{10}$B converters, is extended to gadolinium based detectors. For the first time, a Gd-GEM was successfully operated to detect neutrons with a measured efficiency of 11.8% at a wavelength of 2 Å and a position resolution better than 250 μm.
△ Less
Submitted 2 May, 2016; v1 submitted 8 October, 2015;
originally announced October 2015.
-
Investigation of background in large-area neutron detectors due to alpha emission from impurities in aluminium
Authors:
J. Birch,
J. -C. Buffet,
J. -F. Clergeau,
P. van Esch,
M. Ferraton,
B. Guerard,
R. Hall-Wilton,
L. Hultman,
C. Höglund,
J. Jensen,
A. Khaplanov,
F. Piscitelli
Abstract:
Thermal neutron detector based on films of $^{10}$B$_4$C have been developed as an alternative to $^3$He detectors. In particular, The Multi-Grid detector concept is considered for future large area detectors for ESS and ILL instruments. An excellent signal-to-background ratio is essential to attain expected scientific results. Aluminium is the most natural material for the mechanical structure of…
▽ More
Thermal neutron detector based on films of $^{10}$B$_4$C have been developed as an alternative to $^3$He detectors. In particular, The Multi-Grid detector concept is considered for future large area detectors for ESS and ILL instruments. An excellent signal-to-background ratio is essential to attain expected scientific results. Aluminium is the most natural material for the mechanical structure of of the Multi-Grid detector and other similar concepts due to its mechanical and neutronic properties. Due to natural concentration of $α$ emitters, however, the background from $α$ particles misidentified as neutrons can be unacceptably high. We present our experience operating a detector prototype affected by this issue. Monte Carlo simulations have been used to confirm the background as $α$ particles. The issues have been addressed in the more recent implementations of the Multi-Grid detector by the use of purified aluminium as well as Ni-plating of standard aluminium. The result is the reduction in background by two orders of magnitude. A new large-area prototype has been built incorporating these modifications.
△ Less
Submitted 16 September, 2015; v1 submitted 2 July, 2015;
originally announced July 2015.
-
The uTPC Method: Improving the Position Resolution of Neutron Detectors Based on MPGDs
Authors:
Dorothea Pfeiffer,
Filippo Resnati,
Jens Birch,
Richard Hall-Wilton,
Carina Höglund,
Lars Hultman,
George Iakovidis,
Eraldo Oliveri,
Esko Oksanen,
Leszek Ropelewski,
Patrik Thuiner
Abstract:
Due to the Helium-3 crisis, alternatives to the standard neutron detection techniques are becoming urgent. In addition, the instruments of the European Spallation Source (ESS) require advances in the state of the art of neutron detection. The instruments need detectors with excellent neutron detection efficiency, high-rate capabilities and unprecedented spatial resolution. The Macromolecular Cryst…
▽ More
Due to the Helium-3 crisis, alternatives to the standard neutron detection techniques are becoming urgent. In addition, the instruments of the European Spallation Source (ESS) require advances in the state of the art of neutron detection. The instruments need detectors with excellent neutron detection efficiency, high-rate capabilities and unprecedented spatial resolution. The Macromolecular Crystallography instrument (NMX) requires a position resolution in the order of 200 um over a wide angular range of incoming neutrons. Solid converters in combination with Micro Pattern Gaseous Detectors (MPGDs) are proposed to meet the new requirements. Charged particles rising from the neutron capture have usually ranges larger than several millimetres in gas. This is apparently in contrast with the requirements for the position resolution. In this paper, we present an analysis technique, new in the field of neutron detection, based on the Time Projection Chamber (TPC) concept. Using a standard Single-GEM with the cathode coated with 10B4C, we extract the neutron interaction point with a resolution of better than sigma = 200 um.
△ Less
Submitted 20 January, 2015;
originally announced January 2015.
-
Neutron Position Sensitive Detectors for the ESS
Authors:
Oliver Kirstein,
Richard Hall-Wilton,
Irina Stefanescu,
Maddi Etxegarai,
Michail Anastasopoulos,
Kevin Fissum,
Anna Gulyachkina,
Carina Höglund,
Mewlude Imam,
Kalliopi Kanaki,
Anton Khaplanov,
Thomas Kittelmann,
Scott Kolya,
Björn Nilsson,
Luis Ortega,
Dorothea Pfeiffer,
Francesco Piscitelli,
Judith Freita Ramos,
Linda Robinson,
Julius Scherzinger
Abstract:
The European Spallation Source (ESS) in Lund, Sweden will become the world's leading neutron source for the study of materials. The instruments are being selected from conceptual proposals submitted by groups from around Europe. These instruments present numerous challenges for detector technology in the absence of the availability of Helium-3, which is the default choice for detectors for instrum…
▽ More
The European Spallation Source (ESS) in Lund, Sweden will become the world's leading neutron source for the study of materials. The instruments are being selected from conceptual proposals submitted by groups from around Europe. These instruments present numerous challenges for detector technology in the absence of the availability of Helium-3, which is the default choice for detectors for instruments built until today and due to the extreme rates expected across the ESS instrument suite. Additionally a new generation of source requires a new generation of detector technologies to fully exploit the opportunities that this source provides. The detectors will be sourced from partners across Europe through numerous in-kind arrangements; a process that is somewhat novel for the neutron scattering community. This contribution presents briefly the current status of detectors for the ESS, and outlines the timeline to completion. For a conjectured instrument suite based upon instruments recommended for construction, a recently updated snapshot of the current expected detector requirements is presented. A strategy outline as to how these requirements might be tackled by novel detector developments is shown. In terms of future developments for the neutron community, synergies should be sought with other disciples, as recognized by various recent initiatives in Europe, in the context of the fundamentally multi-disciplinary nature of detectors. This strategy has at its basis the in-kind and collaborative partnerships necessary to be able to produce optimally performant detectors that allow the ESS instruments to be world-leading. This foresees and encourages a high level of collaboration and interdependence at its core, and rather than each group being all-rounders in every technology, the further development of centres of excellence across Europe for particular technologies and niches.
△ Less
Submitted 23 November, 2014;
originally announced November 2014.
-
A 10B-based neutron detector with stacked Multiwire Proportional Counters and macrostructured cathodes
Authors:
I. Stefanescu,
Y. Abdullahi,
J. Birch,
I. Defendi,
R. Hall-Wilton,
C. Hoglund,
L. Hultman,
M. Zee,
K. Zeitelhack
Abstract:
We present the results of the measurements of the detection efficiency for a 4.7 Å neutron beam incident upon a detector incorporating a stack of up to five MultiWire Proportional Counters (MWPC) with Boron-coated cathodes. The cathodes were made of Aluminum and had a surface exhibiting millimeter-deep V-shaped grooves of 45°, upon which the thin Boron film was deposited by DC magnetron sputtering…
▽ More
We present the results of the measurements of the detection efficiency for a 4.7 Å neutron beam incident upon a detector incorporating a stack of up to five MultiWire Proportional Counters (MWPC) with Boron-coated cathodes. The cathodes were made of Aluminum and had a surface exhibiting millimeter-deep V-shaped grooves of 45°, upon which the thin Boron film was deposited by DC magnetron sputtering. The incident neutrons interacting with the converter layer deposited on the sidewalls of the grooves have a higher capture probability, owing to the larger effective absorption film thickness. This leads to a higher overall detection efficiency for the grooved cathode when compared to a cathode with a flat surface. Both the experimental results and the predictions of the GEANT4 model suggests that a 5-counter detector stack with coated grooved cathodes has the same efficiency as a 7-counter stack with flat cathodes. The reduction in the number of counters in the stack without altering the detection efficiency will prove highly beneficial for large-area position-sensitive detectors for neutron scattering applications, for which the cost-effective manufacturing of the detector and associated readout electronics is an important objective. The proposed detector concept could be a technological option for one of the new chopper spectrometers and other instruments planned to be built at the future European Spallation Source in Sweden. These results with macrostructured cathodes generally apply not just to MWPCs but to other gaseous detectors as well.
△ Less
Submitted 30 September, 2013;
originally announced September 2013.
-
Multi-Grid Boron-10 detector for large area applications in neutron scattering science
Authors:
Ken Andersen,
Thierry Bigault,
Jens Birch,
Jean-Claude Buffet,
Jonathan Correa,
Patrick van Esch,
Bruno Guerard,
Richard Hall-Wilton,
Lars Hultman,
Carina Höglund,
Jens Jensen,
Anton Khaplanov,
Oliver Kirstein,
Francesco Piscitelli,
Christian Vettier
Abstract:
The present supply of 3He can no longer meet the detector demands of the upcoming ESS facility and continued detector upgrades at current neutron sources. Therefore viable alternative technologies are required to support the development of cutting-edge instrumentation for neutron scattering science. In this context, 10B-based detectors are being developed by collaboration between the ESS, ILL, and…
▽ More
The present supply of 3He can no longer meet the detector demands of the upcoming ESS facility and continued detector upgrades at current neutron sources. Therefore viable alternative technologies are required to support the development of cutting-edge instrumentation for neutron scattering science. In this context, 10B-based detectors are being developed by collaboration between the ESS, ILL, and Linkö** University. This paper reports on progress of this technology and the prospects applying it in modern neutron scattering experiments. The detector is made-up of multiple rectangular gas counter tubes coated with B4C, enriched in 10B. An anode wire reads out each tube, thereby giving position of conversion in one of the lateral co-ordinates as well as in depth of the detector. Position resolution in the remaining co-ordinate is obtained by segmenting the cathode tube itself. Boron carbide films have been produced at Linkö** University and a detector built at ILL. The characterization study is presented in this paper, including measurement of efficiency, effects of the fill gas species and pressure, coating thickness variation on efficiency and sensitivity to gamma-rays.
△ Less
Submitted 4 September, 2012;
originally announced September 2012.
-
Bonding mechanism in the nitrides Ti2AlN and TiN: an experimental and theoretical investigation
Authors:
M. Magnuson,
M. Mattesini,
S. Li,
C. Höglund,
M. Beckers,
L. Hultman,
O. Eriksson
Abstract:
The electronic structure of nanolaminate Ti2AlN and TiN thin films has been investigated by bulk-sensitive soft x-ray emission spectroscopy. The measured Ti L, N K, Al L1 and Al L2,3 emission spectra are compared with calculated spectra using ab initio density-functional theory including dipole transition matrix elements. Three different types of bond regions are identified; a relatively weak Ti 3…
▽ More
The electronic structure of nanolaminate Ti2AlN and TiN thin films has been investigated by bulk-sensitive soft x-ray emission spectroscopy. The measured Ti L, N K, Al L1 and Al L2,3 emission spectra are compared with calculated spectra using ab initio density-functional theory including dipole transition matrix elements. Three different types of bond regions are identified; a relatively weak Ti 3d - Al 3p bonding between -1 and -2 eV below the Fermi level, and Ti 3d - N 2p and Ti 3d - N 2s bonding which are deeper in energy observed at -4.8 eV and -15 eV below the Fermi level, respectively. A strongly modified spectral shape of 3s states of Al L2,3 emission from Ti2AlN in comparison to pure Al metal is found, which reflects the Ti 3d - Al 3p hybridization observed in the Al L1 emission. The differences between the electronic and crystal structures of Ti2AlN and TiN are discussed in relation to the intercalated Al layers of the former compound and the change of the materials properties in comparison to the isostructural carbides.
△ Less
Submitted 28 December, 2011;
originally announced December 2011.
-
Electronic structure and chemical bonding anisotropy investigation of wurtzite AlN
Authors:
M. Magnuson,
M. Mattesini,
C. Höglund,
J. Birch,
L. Hultman
Abstract:
The electronic structure and the anisotropy of the Al - N π and σ chemical bonding of wurtzite AlN has been investigated by bulk-sensitive total fluorescence yield absorption and soft x-ray emission spectroscopies. The measured N K, Al L1, and Al L2,3 x-ray emission and N 1s x-ray absorption spectra are compared with calculated spectra using first principles density-functional theory including dip…
▽ More
The electronic structure and the anisotropy of the Al - N π and σ chemical bonding of wurtzite AlN has been investigated by bulk-sensitive total fluorescence yield absorption and soft x-ray emission spectroscopies. The measured N K, Al L1, and Al L2,3 x-ray emission and N 1s x-ray absorption spectra are compared with calculated spectra using first principles density-functional theory including dipole transition matrix elements. The main N 2p - Al 3p hybridization regions are identified at -1.0 to -1.8 eV and -5.0 to -5.5 eV below the top of the valence band. In addition, N 2s - Al 3p and N 2s - Al 3s hybridization regions are found at the bottom of the valence band around -13.5 eV and -15 eV, respectively. A strongly modified spectral shape of Al 3s states in the Al L2,3 emission from AlN in comparison to Al metal is found, which is also reflected in the N 2p - Al 3p hybridization observed in the Al L1 emission. The differences between the electronic structure and chemical bonding of AlN and Al metal are discussed in relation to the position of the hybridization regions and the valence band edge influencing the magnitude of the large band gap.
△ Less
Submitted 28 December, 2011;
originally announced December 2011.
-
Electronic structure investigation of the cubic inverse perovskite Sc3AlN
Authors:
Martin Magnuson,
Maurizio Mattesini,
Carina Höglund,
Igor A. Abrikosov,
Jens Birch,
Lars Hultman
Abstract:
The electronic structure and chemical bonding of the recently discovered inverse perovskite Sc3AlN, in comparison to ScN and Sc metal have been investigated by bulk-sensitive soft x-ray emission spectroscopy. The measured Sc L, N K, Al L1, and Al L2,3 emission spectra are compared with calculated spectra using first principle density-functional theory including dipole transition matrix elements. T…
▽ More
The electronic structure and chemical bonding of the recently discovered inverse perovskite Sc3AlN, in comparison to ScN and Sc metal have been investigated by bulk-sensitive soft x-ray emission spectroscopy. The measured Sc L, N K, Al L1, and Al L2,3 emission spectra are compared with calculated spectra using first principle density-functional theory including dipole transition matrix elements. The main Sc 3d - N 2p and Sc 3d - Al 3p chemical bond regions are identified at -4 eV and -1.4 eV below the Fermi level, respectively. A strongly modified spectral shape of 3s states in the Al L2,3 emission from Sc3AlN in comparison to pure Al metal is found, which reflects the Sc 3d - Al 3p hybridization observed in the Al L1 emission. The differences between the electronic structure of Sc3AlN, ScN, and Sc metal are discussed in relation to the change of the conductivity and elastic properties.
△ Less
Submitted 28 December, 2011; v1 submitted 11 December, 2011;
originally announced December 2011.
-
The electronic structure of GaN and Ga investigated by soft x-ray spectroscopy and first-principles methods
Authors:
Martin Magnuson,
Maurizio Mattesini,
Carina Höglund,
Jens Birch,
Lars Hultman
Abstract:
The electronic structure and chemical bonding of wurtzite-GaN investigated by N 1s soft x-ray absorption spectroscopy and N K, Ga M1, and Ga M2,3 emission spectroscopy is compared to that of pure Ga. The measurements are interpreted by calculated spectra using first-principles density-functional theory (DFT) including dipole transition matrix elements and additional on-site Coulomb interaction (WC…
▽ More
The electronic structure and chemical bonding of wurtzite-GaN investigated by N 1s soft x-ray absorption spectroscopy and N K, Ga M1, and Ga M2,3 emission spectroscopy is compared to that of pure Ga. The measurements are interpreted by calculated spectra using first-principles density-functional theory (DFT) including dipole transition matrix elements and additional on-site Coulomb interaction (WC-GGA+U). The Ga 4p - N 2p and Ga 4s - N 2p hybridization and chemical bond regions are identified at the top of the valence band between -1.0 and -2.0 and further down between -5.5 and -6.5 eV, respectively. In addition, N 2s - N 2p - Ga 4s and N 2s - N 2p - Ga 3d hybridization regions occur at the bottom of the valence band between -13 and -15 eV, and between -17.0 and -18.0 eV, respectively. A band-like satellite feature is also found around -10 eV in the Ga M1 and Ga M2,3 emission from GaN, but is absent in pure Ga and the calculated ground state spectra. The difference between the identified spectroscopic features of GaN and Ga are discussed in relation to the various hybridization regions calculated within band-structure methods.
△ Less
Submitted 29 December, 2011; v1 submitted 28 November, 2011;
originally announced November 2011.
-
Origin of the anomalous piezoelectric response in wurtzite Sc$_x$Al$_{1-x}$N alloys
Authors:
Ferenc Tasnádi,
Björn Alling,
Carina Höglund,
Gunilla Wingqvist,
Jens Birch,
Lars Hultman,
Igor A. Abrikosov
Abstract:
The origin of the anomalous, 400% increase of the piezoelectric coefficient in Sc$_x$Al$_{1-x}$N alloys is revealed. Quantum mechanical calculations show that the effect is intrinsic. It comes from a strong change in the response of the internal atomic coordinates to strain and pronounced softening of C$_{33}$ elastic constant. The underlying mechanism is the flattening of the energy landscape due…
▽ More
The origin of the anomalous, 400% increase of the piezoelectric coefficient in Sc$_x$Al$_{1-x}$N alloys is revealed. Quantum mechanical calculations show that the effect is intrinsic. It comes from a strong change in the response of the internal atomic coordinates to strain and pronounced softening of C$_{33}$ elastic constant. The underlying mechanism is the flattening of the energy landscape due to a competition between the parent wurtzite and the so far experimentally unknown hexagonal phases of the alloy. Our observation provides a route for the design of materials with high piezoelectric response.
△ Less
Submitted 17 March, 2010;
originally announced March 2010.
