Showing 1–25 of 25 results for author: Gimeno, B

RADES axion search results with a High-Temperature Superconducting cavity in an 11.7 T magnet

Authors: S. Ahyoune, A. Álvarez Melcón, S. Arguedas Cuendis, S. Calatroni, C. Cogollos, A. Díaz-Morcillo, B. Döbrich, J. D. Gallego, J. M. García-Barceló, B. Gimeno, J. Golm, X. Granados, J. Gutierrez, L. Herwig, I. G. Irastorza, N. Lamas, A. Lozano-Guerrero, W. L. Millar, C. Malbrunot, J. Miralda-Escudé, P. Navarro, J. R. Navarro-Madrid, T. Puig, M. Siodlaczek, G. T. Telles , et al. (1 additional authors not shown)

Abstract: We describe the results of a haloscope axion search performed with an 11.7 T dipole magnet at CERN. The search used a custom-made radio-frequency cavity coated with high-temperature superconducting tape. A set of 27 h of data at a resonant frequency of around 8.84 GHz was analysed. In the range of axion mass 36.5676 $μ$eV to 36.5699 $μ$eV, corresponding to a width of 554 kHz, no signal excess hint… ▽ More We describe the results of a haloscope axion search performed with an 11.7 T dipole magnet at CERN. The search used a custom-made radio-frequency cavity coated with high-temperature superconducting tape. A set of 27 h of data at a resonant frequency of around 8.84 GHz was analysed. In the range of axion mass 36.5676 $μ$eV to 36.5699 $μ$eV, corresponding to a width of 554 kHz, no signal excess hinting at an axion-like particle was found. Correspondingly, in this mass range, a limit on the axion to photon coupling-strength was set in the range between g$_{aγ}\gtrsim$ 6.2e-13 GeV$^{-1}$ and g$_{aγ}\gtrsim$ 1.54e-13 GeV$^{-1}$ with a 95% confidence level. △ Less

Submitted 12 March, 2024; originally announced March 2024.

Comments: 19 pages, 8 figures

Report number: CERN-EP-2024-076, MPP-2024-55

Study of a cubic cavity resonator for gravitational waves detection in the microwave frequency range

Authors: Pablo Navarro, Benito Gimeno, Juan Monzó-Cabrera, Alejandro Díaz-Morcillo, Diego Blas

Abstract: The direct detection of gravitational waves (GWs) of frequencies above MHz has recently received considerable attention. In this work we present a precise study of the reach of a cubic cavity resonator to GWs in the microwave range, using for the first time tools allowing to perform realistic simulations. Concretely, the BI-RME 3D method, which allows us to obtain not only the detected power but a… ▽ More The direct detection of gravitational waves (GWs) of frequencies above MHz has recently received considerable attention. In this work we present a precise study of the reach of a cubic cavity resonator to GWs in the microwave range, using for the first time tools allowing to perform realistic simulations. Concretely, the BI-RME 3D method, which allows us to obtain not only the detected power but also the detected voltage (magnitude and phase), is used here. After analyzing three cubic cavities for different frequencies and working simultaneously with three different degenerate modes at each cavity, we conclude that the sensitivity of the experiment is strongly dependent on the polarization and incidence angle of the GW. The presented experiment can reach sensitivities up to $ 1 \cdot 10^{-19}$ at 100\, MHz, $ 2 \cdot 10^{-20}$ at 1\, GHz, and $ 6 \cdot 10^{-19}$ at 10\, GHz for optimal angles and polarizations, and where in all cases we assumed an integration time of $Δt = 1$ ms. These results provide a strong case for further develo** the use of cavities to detect GWs. Moreover, the possibility of analyzing the detected voltage (magnitude and phase) opens a new interferometric detection scheme based on the combination of the detected signals from multiple cavities. △ Less

Submitted 17 June, 2024; v1 submitted 4 December, 2023; originally announced December 2023.

Comments: 26 pages, 12 figures; v2 matches published version; v3 typo fixed

Enhancing resonant circular-section haloscopes for dark matter axion detection: approaches and limitations in volume expansion

Authors: J. M. García-Barceló, A. Díaz-Morcillo, B. Gimeno

Abstract: Haloscopes, microwave resonant cavities utilized in detecting dark matter axions within powerful static magnetic fields, are pivotal in modern astrophysical research. This paper delves into the realm of cylindrical geometries, investigating techniques to augment volume and enhance compatibility with dipole or solenoid magnets. The study explores volume constraints in two categories of haloscope de… ▽ More Haloscopes, microwave resonant cavities utilized in detecting dark matter axions within powerful static magnetic fields, are pivotal in modern astrophysical research. This paper delves into the realm of cylindrical geometries, investigating techniques to augment volume and enhance compatibility with dipole or solenoid magnets. The study explores volume constraints in two categories of haloscope designs: those reliant on single cavities and those employing multicavities. In both categories, strategies to increase the expanse of elongated structures are elucidated. For multicavities, the optimization of space within magnets is explored through 1D configurations. Three subcavity stacking approaches are investigated, while the foray into 2D and 3D geometries lays the groundwork for future topological developments. The results underscore the efficacy of these methods, revealing substantial room for progress in cylindrical haloscope design. Notably, an elongated single cavity design attains a three-order magnitude increase in volume compared to a WC-109 standard waveguide-based single cavity. Diverse prototypes featuring single cavities, 1D, 2D, and 3D multicavities highlight the feasibility of leveraging these geometries to magnify the volume of tangible haloscope implementations. △ Less

Submitted 25 October, 2023; v1 submitted 22 September, 2023; originally announced September 2023.

Dielectric Assist Accelerating Structures for Compact Linear Accelerators of Low Energy Particles in Hadrontherapy Treatments

Authors: Pablo Martinez-Reviriego, Daniel Esperante, Alexej Grudiev, Benito Gimeno, César Blanch, Daniel González-Iglesias, Nuria Fuster-Martínez, Pablo Martín-Luna, Eduardo Martínez, Abraham Menendez, Juan Fuster

Abstract: Dielectric Assist Accelerating (DAA) structures based on ultralow-loss ceramic are being studied as an alternative to conventional disk-loaded copper cavities. This accelerating structure consists of dielectric disks with irises arranged periodically in metallic structures working under the TM$_{02}$-$π$ mode. In this paper, the numerical design of an S-band DAA structure for low beta particles, s… ▽ More Dielectric Assist Accelerating (DAA) structures based on ultralow-loss ceramic are being studied as an alternative to conventional disk-loaded copper cavities. This accelerating structure consists of dielectric disks with irises arranged periodically in metallic structures working under the TM$_{02}$-$π$ mode. In this paper, the numerical design of an S-band DAA structure for low beta particles, such as protons or carbon ions used for Hadrontherapy treatments, is shown. Four dielectric materials with different permittivity and loss tangent are studied as well as different particle velocities. Through optimization, a design that concentrates most of the RF power in the vacuum space near the beam axis is obtained, leading to a significant reduction of power loss on the metallic walls. This allows to fabricate cavities with an extremely high quality factor, over 100 000, and shunt impedance over 300 M$Ω$/m at room temperature. During the numerical study, the design optimization has been improved by adjusting some of the cell parameters in order to both increase the shunt impedance and reduce the peak electric field in certain locations of the cavity, which can lead to instabilities in its normal functioning. △ Less

Submitted 7 August, 2023; originally announced August 2023.

Non-resonant ultra-fast multipactor regime in dielectric-assist accelerating structures

Authors: Daniel González-Iglesias, Benito Gimeno, Daniel Esperante, Pablo Martinez-Reviriego, Pablo Martín-Luna, Nuria Fuster-Martínez, César Blanch, Eduardo Martínez, Abraham Menendez, Juan Fuster, Alexej Grudiev

Abstract: The objective of this work is the evaluation of the risk of suffering a multipactor discharge in an S-band dielectric-assist accelerating (DAA) structure for a compact low-energy linear particle accelerator dedicated to hadrontherapy treatments. A DAA structure consists of ultra-low loss dielectric ciylinders and disks with irises which are periodically arranged in a metallic enclosure, with the a… ▽ More The objective of this work is the evaluation of the risk of suffering a multipactor discharge in an S-band dielectric-assist accelerating (DAA) structure for a compact low-energy linear particle accelerator dedicated to hadrontherapy treatments. A DAA structure consists of ultra-low loss dielectric ciylinders and disks with irises which are periodically arranged in a metallic enclosure, with the advantage of having an extremely high quality factor and very high shunt impedance at room temperature, and it is therefore proposed as a potential alternative to conventional disk-loaded copper structures. However, it has been observed that these structures suffer from multipactor discharges. In fact, multipactor is one of the main problems of these devices, as it limits the maximum accelerating gradient. Because of this, the analysis of multipactor risk in the early design steps of DAA cavities is crucial to ensure the correct performance of the device after fabrication. In this paper, we present a comprehensive and detailed study of multipactor in our DAA design through numerical simulations performed with an in-house developed code based on the Monte-Carlo method. The phenomenology of the multipactor (resonant electron trajectories, electron flight time between impacts, etc.) is described in detail for different values of the accelerating gradient. It has been found that in these structures an ultra-fast non-resonant multipactor appears, which is different from the types of multipactor theoretically studied in the scientific literature. In addition, the effect of several low electron emission coatings on the multipactor threshold is investigated. Furthermore, a novel design based on the modification of the DAA cell geometry for multipactor mitigation is introduced, which shows a significant increase in the accelerating gradient handling capabilities of our prototype. △ Less

Submitted 26 July, 2023; originally announced July 2023.

A proposal for a low-frequency axion search in the 1-2 $μ$eV range and below with the BabyIAXO magnet

Authors: S. Ahyoune, A. Álvarez Melcón, S. Arguedas Cuendis, S. Calatroni, C. Cogollos, J. Devlin, A. Díaz-Morcillo, D. Díez-Ibáñez, B. Döbrich, J. Galindo, J. D. Gallego, J. M. García-Barceló, B. Gimeno, J. Golm, Y. Gu, L. Herwig, I. G. Irastorza, A. J. Lozano-Guerrero, C. Malbrunot, J. Miralda-Escudé, J. Monzó-Cabrera, P. Navarro, J. R. Navarro-Madrid, J. Redondo, J. Reina-Valero , et al. (5 additional authors not shown)

Abstract: In the near future BabyIAXO will be the most powerful axion helioscope, relying on a custom-made magnet of two bores of 70 cm diameter and 10 m long, with a total available magnetic volume of more than 7 m$^3$. In this document, we propose and describe the implementation of low-frequency axion haloscope setups suitable for operation inside the BabyIAXO magnet. The RADES proposal has a potential se… ▽ More In the near future BabyIAXO will be the most powerful axion helioscope, relying on a custom-made magnet of two bores of 70 cm diameter and 10 m long, with a total available magnetic volume of more than 7 m$^3$. In this document, we propose and describe the implementation of low-frequency axion haloscope setups suitable for operation inside the BabyIAXO magnet. The RADES proposal has a potential sensitivity to the axion-photon coupling $g_{aγ}$ down to values corresponding to the KSVZ model, in the (currently unexplored) mass range between 1 and 2$~μ$eV, after a total effective exposure of 440 days. This mass range is covered by the use of four differently dimensioned 5-meter-long cavities, equipped with a tuning mechanism based on inner turning plates. A setup like the one proposed would also allow an exploration of the same mass range for hidden photons coupled to photons. An additional complementary apparatus is proposed using LC circuits and exploring the low energy range ($\sim10^{-4}-10^{-1}~μ$eV). The setup includes a cryostat and cooling system to cool down the BabyIAXO bore down to about 5 K, as well as appropriate low-noise signal amplification and detection chain. △ Less

Submitted 22 November, 2023; v1 submitted 29 June, 2023; originally announced June 2023.

Methods and restrictions to increase the volume of resonant rectangular-section haloscopes for detecting dark matter axions

Authors: J. M. García-Barceló, A. Álvarez Melcón, A. Díaz-Morcillo, B. Gimeno, A. J. Lozano-Guerrero, J. Monzo-Cabrera, J. R. Navarro-Madrid, P. Navarro

Abstract: Haloscopes are resonant cavities that serve as detectors of dark matter axions when they are immersed in a strong static magnetic field. In order to increase the volume and improve its introduction within dipole or solenoid magnets for axion searches, various haloscope design techniques for rectangular geometries are discussed in this study. The volume limits of two types of haloscopes are explore… ▽ More Haloscopes are resonant cavities that serve as detectors of dark matter axions when they are immersed in a strong static magnetic field. In order to increase the volume and improve its introduction within dipole or solenoid magnets for axion searches, various haloscope design techniques for rectangular geometries are discussed in this study. The volume limits of two types of haloscopes are explored: based on single cavities and based on multicavities. For both cases, possibilities for increasing the volume in long and/or tall structures are presented. For multicavities, 1D geometries are explored to optimize the space in the magnets. Also, 2D and 3D geometries are introduced as a first step for laying the foundations for the development of these kind of topologies. The results prove the usefulness of the developed methods, evidencing the ample room of improvement in rectangular haloscope designs nowadays. A factor of three orders of magnitude improvement in volume compared with a single cavity based on WR-90 standard waveguide is obtained with the design of a long and tall single cavity. Similar procedures have been applied for long and tall multicavities. Experimental measurements are shown for prototypes based on tall multicavities and 2D structures, demonstrating the feasibility of using these types of geometries to increase the volume in real haloscopes. △ Less

Submitted 24 February, 2023; v1 submitted 21 February, 2023; originally announced February 2023.

Novel reaction force for ultra-relativistic dynamics of a classical point charge

Authors: P. Martín-Luna, D. González-Iglesias, B. Gimeno, D. Esperante, C. Blanch, N. Fuster-Martínez, P. Martinez-Reviriego, J. Fuster

Abstract: The problem of the electromagnetic radiation of an accelerated charged particle is one of the most controversial issues in Physics since the beginning of the last century, representing one of the most popular unsolved problems of the Modern Physics. Different equations of motion have been proposed throughout history for a point charge including the electromagnetic radiation emitted, but all these… ▽ More The problem of the electromagnetic radiation of an accelerated charged particle is one of the most controversial issues in Physics since the beginning of the last century, representing one of the most popular unsolved problems of the Modern Physics. Different equations of motion have been proposed throughout history for a point charge including the electromagnetic radiation emitted, but all these expressions show some limitations. An equation based on the principle of conservation of energy is proposed in this work for the ultra-relativistic motion. Different examples are analyzed showing that the energy lost by the charge agrees with the Liénard formula. This proposed equation has been compared with the Landau-Lifshitz equation obtaining a good agreement in the range of application of the Landau-Lifshitz formula. △ Less

Submitted 7 October, 2022; v1 submitted 23 August, 2022; originally announced August 2022.

Comments: 9 pages, 10 figures

The Canfranc Axion Detection Experiment (CADEx): Search for axions at 90 GHz with Kinetic Inductance Detectors

Authors: Beatriz Aja, Sergio Arguedas Cuendis, Ivan Arregui, Eduardo Artal, R. Belén Barreiro, Francisco J. Casas, Maria C. de Ory, Alejandro Díaz-Morcillo, Luisa de la Fuente, Juan Daniel Gallego, José María García-Barceló, Benito Gimeno, Alicia Gomez, Daniel Granados, Bradley J. Kavanagh, Miguel A. G. Laso, Txema Lopetegi, Antonio José Lozano-Guerrero, Maria T. Magaz, Jesús Martín-Pintado, Enrique Martínez-González, Jordi Miralda-Escudé, Juan Monzó-Cabrera, Jose R. Navarro-Madrid, Ana B. Nuñez Chico , et al. (11 additional authors not shown)

Abstract: We propose a novel experiment, the Canfranc Axion Detection Experiment (CADEx), to probe dark matter axions with masses in the range 330-460 $μ$eV, within the W-band (80-110 GHz), an unexplored parameter space in the well-motivated dark matter window of Quantum ChromoDynamics (QCD) axions. The experimental design consists of a microwave resonant cavity haloscope in a high static magnetic field cou… ▽ More We propose a novel experiment, the Canfranc Axion Detection Experiment (CADEx), to probe dark matter axions with masses in the range 330-460 $μ$eV, within the W-band (80-110 GHz), an unexplored parameter space in the well-motivated dark matter window of Quantum ChromoDynamics (QCD) axions. The experimental design consists of a microwave resonant cavity haloscope in a high static magnetic field coupled to a highly sensitive detecting system based on Kinetic Inductance Detectors via optimized quasi-optics (horns and mirrors). The experiment is in preparation and will be installed in the dilution refrigerator of the Canfranc Underground Laboratory. Sensitivity forecasts for axion detection with CADEx, together with the potential of the experiment to search for dark photons, are presented. △ Less

Submitted 6 June, 2022; originally announced June 2022.

Comments: 23 pages, 10 figures

On the use of ferroelectric material in the detection of dark matter axions

Authors: J. M. García Barceló, A. Álvarez Melcón, S. Arguedas Cuendis, A. Díaz-Morcillo, B. Gimeno, A. Kanareykin, A. J. Lozano-Guerrero, P. Navarro, W. Wuensch

Abstract: Tuning is an essential requirement for the search of dark matter axions employing haloscopes since its mass is not known yet to the scientific community. At the present day, most haloscope tuning systems are based on mechanical devices which can lead to failures due to the complexity of the environment in which they are used. However, the electronic tuning making use of ferroelectric materials can… ▽ More Tuning is an essential requirement for the search of dark matter axions employing haloscopes since its mass is not known yet to the scientific community. At the present day, most haloscope tuning systems are based on mechanical devices which can lead to failures due to the complexity of the environment in which they are used. However, the electronic tuning making use of ferroelectric materials can provide a path that is less vulnerable to mechanical failures and thus complements and expands current tuning systems. In this work, we present and design a novel concept for using the ferroelectric Potassium Tantalate ($KTaO_3$ or KTO) material as a tuning element in haloscopes based on coupled microwave cavities. In this line, the structures used in the Relic Axion Detector Exploratory Setup (RADES) group are based on several cavities that are connected by metallic irises, which act as interresonator coupling elements. In this article, we also show how to use these $KTaO_3$ films as interresonator couplings between cavities, instead of inductive or capacitive metallic windows used in the past. These two concepts represent a crucial upgrade over the current systems employed in the dark matter axions community, achieving a tuning range of $2.23 \, \%$ which represents a major improvement as compared to previous works ($<0.1 \, \%$) for the same class of tuning systems. The theoretical and simulated results shown in this work demonstrate the interest of the novel concepts proposed for the incorporation of this kind of ferroelectric media in multicavity resonant haloscopes in the search for dark matter axions. △ Less

Submitted 7 December, 2022; v1 submitted 25 April, 2022; originally announced April 2022.

Comments: Corrected typos. Revised arguments and added figures in several sections, results unchanged. Added references

Axion Dark Matter

Authors: C. B. Adams, N. Aggarwal, A. Agrawal, R. Balafendiev, C. Bartram, M. Baryakhtar, H. Bekker, P. Belov, K. K. Berggren, A. Berlin, C. Boutan, D. Bowring, D. Budker, A. Caldwell, P. Carenza, G. Carosi, R. Cervantes, S. S. Chakrabarty, S. Chaudhuri, T. Y. Chen, S. Cheong, A. Chou, R. T. Co, J. Conrad, D. Croon , et al. (130 additional authors not shown)

Abstract: Axions are well-motivated dark matter candidates with simple cosmological production mechanisms. They were originally introduced to solve the strong CP problem, but also arise in a wide range of extensions to the Standard Model. This Snowmass white paper summarizes axion phenomenology and outlines next-generation laboratory experiments proposed to detect axion dark matter. There are vibrant synerg… ▽ More Axions are well-motivated dark matter candidates with simple cosmological production mechanisms. They were originally introduced to solve the strong CP problem, but also arise in a wide range of extensions to the Standard Model. This Snowmass white paper summarizes axion phenomenology and outlines next-generation laboratory experiments proposed to detect axion dark matter. There are vibrant synergies with astrophysical searches and advances in instrumentation including quantum-enabled readout, high-Q resonators and cavities and large high-field magnets. This white paper outlines a clear roadmap to discovery, and shows that the US is well-positioned to be at the forefront of the search for axion dark matter in the coming decade. △ Less

Submitted 29 March, 2023; v1 submitted 28 March, 2022; originally announced March 2022.

Comments: restore and expand author list

New Horizons: Scalar and Vector Ultralight Dark Matter

Authors: D. Antypas, A. Banerjee, C. Bartram, M. Baryakhtar, J. Betz, J. J. Bollinger, C. Boutan, D. Bowring, D. Budker, D. Carney, G. Carosi, S. Chaudhuri, S. Cheong, A. Chou, M. D. Chowdhury, R. T. Co, J. R. Crespo López-Urrutia, M. Demarteau, N. DePorzio, A. V. Derbin, T. Deshpande, M. D. Chowdhury, L. Di Luzio, A. Diaz-Morcillo, J. M. Doyle , et al. (104 additional authors not shown)

Abstract: The last decade has seen unprecedented effort in dark matter model building at all mass scales coupled with the design of numerous new detection strategies. Transformative advances in quantum technologies have led to a plethora of new high-precision quantum sensors and dark matter detection strategies for ultralight ($<10\,$eV) bosonic dark matter that can be described by an oscillating classical,… ▽ More The last decade has seen unprecedented effort in dark matter model building at all mass scales coupled with the design of numerous new detection strategies. Transformative advances in quantum technologies have led to a plethora of new high-precision quantum sensors and dark matter detection strategies for ultralight ($<10\,$eV) bosonic dark matter that can be described by an oscillating classical, largely coherent field. This white paper focuses on searches for wavelike scalar and vector dark matter candidates. △ Less

Submitted 28 March, 2022; originally announced March 2022.

Comments: Snowmass 2021 White Paper

Design of new resonant haloscopes in the search for the darkmatter axion: a review of the first steps in the RADES collaboration

Authors: A. Díaz-Morcillo, J. M. García Barceló, A. J. Lozano-Guerrero, P. Navarro, B. Gimeno, S. Arguedas Cuendis, A. Álvarez Melcón, C. Cogollos, S. Calatroni, B. Döbrich, J. D. Gallego, J. Golm, I. G. Irastorza, C. Malbrunot, Jordi Miralda-Escudé, C. Peña Garay, J. Redondo, W. Wuensch

Abstract: Within the increasing interest in the dark matter axion detection through haloscopes, in which different international groups are currently involved, the RADES group was established in 2016 with the goal of develo** very sensitive detection systems to be operated in dipole magnets. This review deals with the work developed by this collaboration during its first five years, from the first designs… ▽ More Within the increasing interest in the dark matter axion detection through haloscopes, in which different international groups are currently involved, the RADES group was established in 2016 with the goal of develo** very sensitive detection systems to be operated in dipole magnets. This review deals with the work developed by this collaboration during its first five years, from the first designs, based on the multi-cavity concept, aiming to increase the haloscope volume and, so, to improve its sensitivity, their evolution, the data acquisition design, and, finally, the first experimental run. Moreover, the envisaged work within RADES, for both dipole and solenoid magnets, in the short and medium term is also presented. △ Less

Submitted 22 January, 2022; v1 submitted 29 November, 2021; originally announced November 2021.

Comments: Review paper, 24 pages, 18 figures, 57 references

Journal ref: Universe 2022, 8, 5

Wide-band full-wave electromagnetic modal analysis of the coupling between dark-matter axions and photons in microwave resonators

Authors: P. Navarro, Benito Gimeno, A. Alvarez Melcon, S. Arguedas Cuendis, C. Cogollos, A. Diaz-Morcillo, J. D. Gallego, J. M. Garcia Barcelo, J. Golm, I. G. Irastorza, A. J. Lozano Guerrero, C. Penya Garay

Abstract: The electromagnetic coupling axion-photon in a microwave cavity is revisited with the Boundary Integral - Resonant Mode Expansion (BI-RME) 3D technique. Such full-wave modal technique has been applied for the rigorous analysis of the excitation of a microwave cavity with an axion field. In this scenario, the electromagnetic field generated by the axion-photon coupling can be assumed to be driven b… ▽ More The electromagnetic coupling axion-photon in a microwave cavity is revisited with the Boundary Integral - Resonant Mode Expansion (BI-RME) 3D technique. Such full-wave modal technique has been applied for the rigorous analysis of the excitation of a microwave cavity with an axion field. In this scenario, the electromagnetic field generated by the axion-photon coupling can be assumed to be driven by equivalent electrical charge and current densities. These densities have been inserted in the general BI-RME 3D equations, which express the RF electromagnetic field existing within a cavity as an integral involving the Dyadic Green functions of the cavity (under Coulomb gauge) as well as such densities. This method is able to take into account any arbitrary spatial and temporal variation of both magnitude and phase of the axion field. Next, we have obtained a simple network driven by the axion current source, which represents the coupling between the axion field and the resonant modes of the cavity. With this approach, it is possible to calculate the extracted and dissipated RF power as a function of frequency along a broad band and without Cauchy-Lorentz approximations, obtaining the spectrum of the electromagnetic field generated in the cavity, and dealing with modes relatively close to the axion resonant mode. Moreover, with this technique we have a complete knowledge of the signal extracted from the cavity, not only in magnitude but also in phase. This can be an interesting issue for future analysis where the axion phase is an important parameter. △ Less

Submitted 11 April, 2022; v1 submitted 7 July, 2021; originally announced July 2021.

Comments: 37 pages, 14 figures, 40 references

Journal ref: Physics of the Dark Universe 36 (2022) 101001

First results of the CAST-RADES haloscope search for axions at 34.67 $μ$eV

Authors: A. Álvarez Melcón, S. Arguedas Cuendis, J. Baier, K. Barth, H. Bräuniger, S. Calatroni, G. Cantatore, F. Caspers, J. F Castel, S. A. Cetin, C. Cogollos, T. Dafni, M. Davenport, A. Dermenev, K. Desch, A. Díaz-Morcillo, B. Döbrich, H. Fischer, W. Funk, J. D Gallego, J. M García Barceló, A. Gardikiotis, J. Garza, B. Gimeno, S. Gninenko , et al. (34 additional authors not shown)

Abstract: We present results of the Relic Axion Dark-Matter Exploratory Setup (RADES), a detector which is part of the CERN Axion Solar Telescope (CAST), searching for axion dark matter in the 34.67$μ$eV mass range. A radio frequency cavity consisting of 5 sub-cavities coupled by inductive irises took physics data inside the CAST dipole magnet for the first time using this filter-like haloscope geometry. An… ▽ More We present results of the Relic Axion Dark-Matter Exploratory Setup (RADES), a detector which is part of the CERN Axion Solar Telescope (CAST), searching for axion dark matter in the 34.67$μ$eV mass range. A radio frequency cavity consisting of 5 sub-cavities coupled by inductive irises took physics data inside the CAST dipole magnet for the first time using this filter-like haloscope geometry. An exclusion limit with a 95% credibility level on the axion-photon coupling constant of g$_{aγ}\gtrsim 4\times10^{-13} \text{GeV}^{-1}$ over a mass range of 34.6738 $μ$eV < $m_a$ < 34.6771 $μ$eV is set. This constitutes a significant improvement over the current strongest limit set by CAST at this mass and is at the same time one of the most sensitive direct searches for an axion dark matter candidate above the mass of 25 $μ$eV. The results also demonstrate the feasibility of exploring a wider mass range around the value probed by CAST-RADES in this work using similar coherent resonant cavities. △ Less

Submitted 27 October, 2021; v1 submitted 28 April, 2021; originally announced April 2021.

Comments: 14 pages, 9 figures. Accepted for publication in JHEP. Minor changes done compared to the previous version

Report number: CERN-EP-2021-070

Journal ref: J. High Energ. Phys. 2021, 75 (2021)

Analysis of multipactor effect in parallel-plate and rectangular waveguides

Authors: A. Berenguer, A. Coves, E. Bronchalo, B. Gimeno, V. Boria

Abstract: In this work it is investigated, in the parallel-plate waveguide case, how the 1D, 2D or 3D motion of the electrons inside the waveguide can affect the generalized susceptibility diagrams, by means of a developed model capable of tracking the exact trajectory of multiple effective electrons which includes effects such as the spreading of the secondary electron departure kinetic energies or the dep… ▽ More In this work it is investigated, in the parallel-plate waveguide case, how the 1D, 2D or 3D motion of the electrons inside the waveguide can affect the generalized susceptibility diagrams, by means of a developed model capable of tracking the exact trajectory of multiple effective electrons which includes effects such as the spreading of the secondary electron departure kinetic energies or the dependence on elastic and inelastic electrons. On the other hand, a comparative study of the susceptibility charts in a parallel-plate and in its equivalent rectangular waveguide with the same height is performed, showing how the inhomogeneity of the electric field inside the waveguide modifies the multipactor region with respect to that predicted by the parallel-plate waveguide case. The results of this study are going to be extended to a partially dielectric-loaded rectangular waveguide, which is a problem of great interest in the space industry that has not yet been rigorously investigated in the literature. △ Less

Submitted 2 May, 2020; originally announced May 2020.

Analysis of mathematical techniques for the calculation of the electrostatic field in a dielectric-loaded waveguide

Authors: A. Berenguer, A. Coves, E. Bronchalo, F. Mesa, B. Gimeno

Abstract: The resolution of the Green's function for obtaining the electrostatic potential generated by the charges located in the dielectric layer of a rectangular waveguide requires efficient integration techniques. Due to the characteristics and the oscillatory nature of the function to be integrated, the use of the Filon's method together with a convergence analysis is adequate. However, the application… ▽ More The resolution of the Green's function for obtaining the electrostatic potential generated by the charges located in the dielectric layer of a rectangular waveguide requires efficient integration techniques. Due to the characteristics and the oscillatory nature of the function to be integrated, the use of the Filon's method together with a convergence analysis is adequate. However, the application of this numerical integration technique can lead to numerical instabilities in the result. For this reason, in this research work we have presented two different methods to deal with these numerical errors of integration: SSA/MSSA and GPR. In this way it is possible to clean the electrostatic potential avoiding subsequent errors in the calculation of the electrostatic field. △ Less

Submitted 2 May, 2020; originally announced May 2020.

Comments: arXiv admin note: text overlap with arXiv:2005.00909

Analysis of the electrostratic field generated by a charge distribution on a dielectric layer loading a rectangular waveguide

Authors: A. Berenguer, A. Coves, F. Mesa, E. Bronchalo, B. Gimeno, V. Boria

Abstract: The goal of this paper is to study the electrostatic field due to an arbitrary charge distribution on a dielectric layer in a dielectric-loaded rectangular waveguide. In order to obtain this electrostatic field, the potential due to a point charge on the dielectric layer is solved in advance. The high computational complexity of this problem requires the use of different numerical integration tech… ▽ More The goal of this paper is to study the electrostatic field due to an arbitrary charge distribution on a dielectric layer in a dielectric-loaded rectangular waveguide. In order to obtain this electrostatic field, the potential due to a point charge on the dielectric layer is solved in advance. The high computational complexity of this problem requires the use of different numerical integration techniques (e.g. Filon, Gauss-Kronrod, Lobatto, ...) and interpolation methods. Using the principle of superposition, the potential due to an arbitrary charge distribution on a dielectric layer is obtained by adding the individual contribution of each point charge. Finally, a numerical differentiation of the potential is carried out to obtain the electrostatic field in the waveguide. The results of this electrostatic problem are going to be extended to model the multipactor effect, which is a problem of great interest in the space industry. △ Less

Submitted 2 May, 2020; originally announced May 2020.

Scalable haloscopes for axion dark matter detection in the 30$μ$eV range with RADES

Authors: A. Álvarez Melcón, S. Arguedas Cuendis, C. Cogollos, A. Díaz-Morcillo, B. Döbrich, J. D. Gallego, J. M. García Barceló, B. Gimeno, J. Golm, I. G. Irastorza, A. J. Lozano-Guerrero, C. Malbrunot, A. Millar, P. Navarro, C. Peña Garay, J. Redondo, W. Wuensch

Abstract: RADES (Relic Axion Detector Exploratory Setup) is a project with the goal of directly searching for axion dark matter above the $30 μ$eV scale employing custom-made microwave filters in magnetic dipole fields. Currently RADES is taking data at the LHC dipole of the CAST experiment. In the long term, the RADES cavities are envisioned to take data in the (baby)-IAXO magnet. In this article we report… ▽ More RADES (Relic Axion Detector Exploratory Setup) is a project with the goal of directly searching for axion dark matter above the $30 μ$eV scale employing custom-made microwave filters in magnetic dipole fields. Currently RADES is taking data at the LHC dipole of the CAST experiment. In the long term, the RADES cavities are envisioned to take data in the (baby)-IAXO magnet. In this article we report on the modelling, building and characterisation of an optimised microwave-filter design with alternating irises that exploits maximal coupling to axions while being scalable in length without suffering from mode-mixing. We develop the mathematical formalism and theoretical study which justifies the performance of the chosen design. We also point towards the applicability of this formalism to optimise the MADMAX dielectric haloscopes. △ Less

Submitted 22 June, 2020; v1 submitted 18 February, 2020; originally announced February 2020.

Comments: 27 pages, 16 figures, v3: expanded sensitivity discussion, version accepted for publication in JHEP

Report number: NORDITA-2020-010

The 3 cavity prototypes of RADES, an axion detector using microwave filters at CAST

Authors: S. Arguedas Cuendis, A. Álvarez Melcón, C. Cogollos, A. Díaz-Morcillo, B. Döbrich, J. D. Gallego, B. Gimeno, I. G. Irastorza, A. J. Lozano-Guerrero, C. Malbrunot, P. Navarro, C. Peña Garay, J. Redondo, T. Vafeiadis, W. Wuensch

Abstract: The Relic Axion Detector Experimental Setup (RADES) is an axion search project that uses a microwave filter as resonator for Dark Matter conversion. The main focus of this publication is the description of the 3 different cavity prototypes of RADES. The result of the first tests of one of the prototypes is also presented. The filters consist of 5 or 6 stainless steel sub-cavities joined by rectang… ▽ More The Relic Axion Detector Experimental Setup (RADES) is an axion search project that uses a microwave filter as resonator for Dark Matter conversion. The main focus of this publication is the description of the 3 different cavity prototypes of RADES. The result of the first tests of one of the prototypes is also presented. The filters consist of 5 or 6 stainless steel sub-cavities joined by rectangular irises. The size of the sub-cavities determines the working frequency, the amount of sub-cavities determine the working volume. The first cavity prototype was built in 2017 to work at a frequency of $\sim$ 8.4 GHz and it was placed at the 9 T CAST dipole magnet at CERN. Two more prototypes were designed and built in 2018. The aim of the new designs is to find and test the best cavity geometry in order to scale up in volume and to introduce an effective tuning mechanism. Our results demonstrate the promising potential of this type of filter to reach QCD axion sensitivity at X-Band frequencies. △ Less

Submitted 11 March, 2019; originally announced March 2019.

Comments: Proceedings for the 3rd Axion Cavity and Detector Workshop, Livermore Valley Open Campus August 21-25th, 2018

The Compact Linear Collider (CLIC) - 2018 Summary Report

Authors: The CLIC, CLICdp collaborations, :, T. K. Charles, P. J. Giansiracusa, T. G. Lucas, R. P. Rassool, M. Volpi, C. Balazs, K. Afanaciev, V. Makarenko, A. Patapenka, I. Zhuk, C. Collette, M. J. Boland, A. C. Abusleme Hoffman, M. A. Diaz, F. Garay, Y. Chi, X. He, G. Pei, S. Pei, G. Shu, X. Wang, J. Zhang , et al. (671 additional authors not shown)

Abstract: The Compact Linear Collider (CLIC) is a TeV-scale high-luminosity linear $e^+e^-$ collider under development at CERN. Following the CLIC conceptual design published in 2012, this report provides an overview of the CLIC project, its current status, and future developments. It presents the CLIC physics potential and reports on design, technology, and implementation aspects of the accelerator and the… ▽ More The Compact Linear Collider (CLIC) is a TeV-scale high-luminosity linear $e^+e^-$ collider under development at CERN. Following the CLIC conceptual design published in 2012, this report provides an overview of the CLIC project, its current status, and future developments. It presents the CLIC physics potential and reports on design, technology, and implementation aspects of the accelerator and the detector. CLIC is foreseen to be built and operated in stages, at centre-of-mass energies of 380 GeV, 1.5 TeV and 3 TeV, respectively. CLIC uses a two-beam acceleration scheme, in which 12 GHz accelerating structures are powered via a high-current drive beam. For the first stage, an alternative with X-band klystron powering is also considered. CLIC accelerator optimisation, technical developments and system tests have resulted in an increased energy efficiency (power around 170 MW) for the 380 GeV stage, together with a reduced cost estimate at the level of 6 billion CHF. The detector concept has been refined using improved software tools. Significant progress has been made on detector technology developments for the tracking and calorimetry systems. A wide range of CLIC physics studies has been conducted, both through full detector simulations and parametric studies, together providing a broad overview of the CLIC physics potential. Each of the three energy stages adds cornerstones of the full CLIC physics programme, such as Higgs width and couplings, top-quark properties, Higgs self-coupling, direct searches, and many precision electroweak measurements. The interpretation of the combined results gives crucial and accurate insight into new physics, largely complementary to LHC and HL-LHC. The construction of the first CLIC energy stage could start by 2026. First beams would be available by 2035, marking the beginning of a broad CLIC physics programme spanning 25-30 years. △ Less

Submitted 6 May, 2019; v1 submitted 14 December, 2018; originally announced December 2018.

Comments: 112 pages, 59 figures; published as CERN Yellow Report Monograph Vol. 2/2018; corresponding editors: Philip N. Burrows, Nuria Catalan Lasheras, Lucie Linssen, Marko Petrič, Aidan Robson, Daniel Schulte, Eva Sicking, Steinar Stapnes

Report number: CERN-2018-005-M

Axion Searches with Microwave Filters: the RADES project

Authors: Alejandro Álvarez Melcón, Sergio Arguedas Cuendis, Cristian Cogollos, Alejandro Díaz-Morcillo, Babette Döbrich, Juan Daniel Gallego, Benito Gimeno, Igor G. Irastorza, Antonio José Lozano-Guerrero, Chloé Malbrunot, Pablo Navarro, Carlos Peña Garay, Javier Redondo, Theodoros Vafeiadis, Walter Wuensch

Abstract: We propose, design and construct a variant of the conventional axion haloscope concept that could be competitive in the search for dark matter axions of masses in the decade 10-100 $μ$eV. Theses masses are located somewhat above the mass range in which existing experiments have reached sensitivity to benchmark QCD axion models. Our haloscope consists of an array of small microwave cavities connect… ▽ More We propose, design and construct a variant of the conventional axion haloscope concept that could be competitive in the search for dark matter axions of masses in the decade 10-100 $μ$eV. Theses masses are located somewhat above the mass range in which existing experiments have reached sensitivity to benchmark QCD axion models. Our haloscope consists of an array of small microwave cavities connected by rectangular irises, in an arrangement commonly used in radio-frequency filters. The size of the unit cavity determines the main resonant frequency, while the possibility to connect a {large} number of cavities allows to reach large detection volumes. We develop the theoretical framework of the detection concept, and present design prescriptions to optimize detection capabilities. We describe the design and realization of a first small-scale prototype of this concept, called Relic Axion Detector Exploratory Setup (RADES). It consists of a copper-coated stainless steel five-cavities microwave filter with the detecting mode operating at around 8.4 GHz. This structure has been electromagnetically characterized at 2 K and 298 K, and it is now placed in ultra-high vacuum in one of the twin-bores of the 9 T CAST dipole magnet at CERN. We describe the data acquisition system developed for relic axion detection, and present preliminary results of the electromagnetic properties of the microwave filter, which show the potential of filters to reach QCD axion window sensitivity at X-band frequencies. △ Less

Submitted 17 May, 2018; v1 submitted 3 March, 2018; originally announced March 2018.

Comments: approved for publication in JCAP, version after referee comments

Report number: MPP-2018-18

Analysis of Metal-Dielectric Waveguides with Circular Sectors

Authors: Daniel Torrent, Benito Gimeno, Vicente E. Boria, José Sánchez-Dehesa

Abstract: The study of metallic corrugated surfaces has recently received strong attention due to their ability to mimic the behaviour of surface plasmons. In this work, this plasmon-like behaviour is employed to design an open cylindrical waveguide. The structure consists on a longitudinally corrugated metallic cylinder with corrugations filled with a dielectric material. The dispersion relation of this wa… ▽ More The study of metallic corrugated surfaces has recently received strong attention due to their ability to mimic the behaviour of surface plasmons. In this work, this plasmon-like behaviour is employed to design an open cylindrical waveguide. The structure consists on a longitudinally corrugated metallic cylinder with corrugations filled with a dielectric material. The dispersion relation of this waveguide is analyzed in the Òcontinuous limitÓ, defined as the limit in which the number of corrugations is infinite, but kee** their periodicity constant. It is found that, in this limit, the waveguide supports only TE guided modes and their dispersion relation becomes highly degenerated. Finally, it is shown that the waveguide behaves as an anisotropic cylindrical rod with extreme electromagnetic parameters, what makes it possible to apply these structures not only as waveguides but also as building blocks for metamaterials. △ Less

Submitted 22 April, 2014; originally announced April 2014.

Conceptual Design of the International Axion Observatory (IAXO)

Authors: E. Armengaud, F. T. Avignone, M. Betz, P. Brax, P. Brun, G. Cantatore, J. M. Carmona, G. P. Carosi, F. Caspers, S. Caspi, S. A. Cetin, D. Chelouche, F. E. Christensen, A. Dael, T. Dafni, M. Davenport, A. V. Derbin, K. Desch, A. Diago, B. Döbrich, I. Dratchnev, A. Dudarev, C. Eleftheriadis, G. Fanourakis, E. Ferrer-Ribas , et al. (63 additional authors not shown)

Abstract: The International Axion Observatory (IAXO) will be a forth generation axion helioscope. As its primary physics goal, IAXO will look for axions or axion-like particles (ALPs) originating in the Sun via the Primakoff conversion of the solar plasma photons. In terms of signal-to-noise ratio, IAXO will be about 4-5 orders of magnitude more sensitive than CAST, currently the most powerful axion heliosc… ▽ More The International Axion Observatory (IAXO) will be a forth generation axion helioscope. As its primary physics goal, IAXO will look for axions or axion-like particles (ALPs) originating in the Sun via the Primakoff conversion of the solar plasma photons. In terms of signal-to-noise ratio, IAXO will be about 4-5 orders of magnitude more sensitive than CAST, currently the most powerful axion helioscope, reaching sensitivity to axion-photon couplings down to a few $\times 10^{-12}$ GeV$^{-1}$ and thus probing a large fraction of the currently unexplored axion and ALP parameter space. IAXO will also be sensitive to solar axions produced by mechanisms mediated by the axion-electron coupling $g_{ae}$ with sensitivity $-$for the first time$-$ to values of $g_{ae}$ not previously excluded by astrophysics. With several other possible physics cases, IAXO has the potential to serve as a multi-purpose facility for generic axion and ALP research in the next decade. In this paper we present the conceptual design of IAXO, which follows the layout of an enhanced axion helioscope, based on a purpose-built 20m-long 8-coils toroidal superconducting magnet. All the eight 60cm-diameter magnet bores are equipped with focusing x-ray optics, able to focus the signal photons into $\sim 0.2$ cm$^2$ spots that are imaged by ultra-low-background Micromegas x-ray detectors. The magnet is built into a structure with elevation and azimuth drives that will allow for solar tracking for $\sim$12 h each day. △ Less

Submitted 14 January, 2014; originally announced January 2014.

Comments: 47 pages, submitted to JINST

Journal ref: JINST 9 (2014) T05002

IAXO - The International Axion Observatory

Authors: J. K. Vogel, F. T. Avignone, G. Cantatore, J. M. Carmona, S. Caspi, S. A. Cetin, F. E. Christensen, A. Dael, T. Dafni, M. Davenport, A. V. Derbin, K. Desch, A. Diago, A. Dudarev, C. Eleftheriadis, G. Fanourakis, E. Ferrer-Ribas, J. Galan, J. A. Garcia, J. G. Garza, T. Geralis, B. Gimeno, I. Giomataris, S. Gninenko, H. Gomez , et al. (39 additional authors not shown)

Abstract: The International Axion Observatory (IAXO) is a next generation axion helioscope aiming at a sensitivity to the axion-photon coupling of a few 10^{-12} GeV^{-1}, i.e. 1-1.5 orders of magnitude beyond sensitivities achieved by the currently most sensitive axion helioscope, the CERN Axion Solar Telescope (CAST). Crucial factors in improving the sensitivity for IAXO are the increase of the magnetic f… ▽ More The International Axion Observatory (IAXO) is a next generation axion helioscope aiming at a sensitivity to the axion-photon coupling of a few 10^{-12} GeV^{-1}, i.e. 1-1.5 orders of magnitude beyond sensitivities achieved by the currently most sensitive axion helioscope, the CERN Axion Solar Telescope (CAST). Crucial factors in improving the sensitivity for IAXO are the increase of the magnetic field volume together with the extensive use of x-ray focusing optics and low background detectors, innovations already successfully tested at CAST. Electron-coupled axions invoked to explain the white dwarf cooling, relic axions, and a large variety of more generic axion-like particles (ALPs) along with other novel excitations at the low-energy frontier of elementary particle physics could provide additional physics motivation for IAXO. △ Less

Submitted 13 February, 2013; originally announced February 2013.

Comments: 6 pages, 1 figure, Contribution to the 8th Patras Workshop on Axions, WIMPs and WISPs, Chicago, IL, USA, 2012