-
Fracture of bio-cemented sands
Authors:
C. Konstantinou,
E. Martínez-Pañeda,
G. Biscontin,
N. A. Fleck
Abstract:
Bio-chemical reactions enable the production of biomimetic materials such as sandstones. In the present study, microbiologically-induced calcium carbonate precipitation (MICP) is used to manufacture laboratory-scale specimens for fracture toughness measurement. The mode I and mixed-mode fracture toughnesses are measured as a function of cementation, and are correlated with strength, permeability a…
▽ More
Bio-chemical reactions enable the production of biomimetic materials such as sandstones. In the present study, microbiologically-induced calcium carbonate precipitation (MICP) is used to manufacture laboratory-scale specimens for fracture toughness measurement. The mode I and mixed-mode fracture toughnesses are measured as a function of cementation, and are correlated with strength, permeability and porosity. A micromechanical model is developed to predict the dependence of mode I fracture toughness upon the degree of cementation. In addition, the role of the crack tip $T$-stress in dictating kink angle and toughness is determined for mixed mode loading. At a sufficiently low degree of cementation, the zone of microcracking in the vicinity of the crack tip is sufficiently large for a crack tip $K$-field to cease to exist and for crack kinking theory to not apply. The interplay between cementation and fracture properties of sedimentary rocks is explained; this understanding underpins a wide range of rock fracture phenomena including hydraulic fracture.
△ Less
Submitted 13 November, 2023;
originally announced November 2023.
-
Analysis of hydrogen diffusion in the three stage electro-permeation test
Authors:
A. Raina,
V. S. Deshpande,
E. Martínez-Pañeda,
N. A. Fleck
Abstract:
The presence of hydrogen traps within a metallic alloy influences the rate of hydrogen diffusion. The electro-permeation (EP) test can be used to assess this: the permeation of hydrogen through a thin metallic sheet is measured by suitable control of hydrogen concentration on the front face and by recording the flux of hydrogen that exits the rear face. Additional insight is achieved by the more s…
▽ More
The presence of hydrogen traps within a metallic alloy influences the rate of hydrogen diffusion. The electro-permeation (EP) test can be used to assess this: the permeation of hydrogen through a thin metallic sheet is measured by suitable control of hydrogen concentration on the front face and by recording the flux of hydrogen that exits the rear face. Additional insight is achieved by the more sophisticated three stage EP test: the concentration of free lattice hydrogen on the front face is set to an initial level, is then dropped to a lower intermediate value and is then restored to the initial level. The flux of hydrogen exiting the rear face is measured in all three stages of the test. In the present study, a transient analysis is performed of hydrogen permeation in a three stage EP test, assuming that lattice diffusion is accompanied by trap** and de-trap**. The sensitivity of the three stage EP response to the depth and density of hydrogen traps is quantified. A significant difference in permeation response can exist between the first and third stages of the EP test when the alloy contains a high number density of deep traps.
△ Less
Submitted 13 June, 2023;
originally announced June 2023.
-
The mechanical and electrochemical properties of polyaniline-coated carbon nanotube mat
Authors:
Wei Tan,
Joe C. Stallard,
Changshin Jo,
Michael F. L. De Volder,
Norman A. Fleck
Abstract:
The measured capacitance, modulus and strength of carbon nanotube-polyaniline (CNT-PANI) composite electrodes render them promising candidates for structural energy storage devices. Here, CNT-PANI composite electrodes are manufactured with electrodeposition of PANI onto the bundle network of CNT mats produced via a floating catalyst chemical vapour deposition process. PANI comprises 0% to 30% by v…
▽ More
The measured capacitance, modulus and strength of carbon nanotube-polyaniline (CNT-PANI) composite electrodes render them promising candidates for structural energy storage devices. Here, CNT-PANI composite electrodes are manufactured with electrodeposition of PANI onto the bundle network of CNT mats produced via a floating catalyst chemical vapour deposition process. PANI comprises 0% to 30% by volume of the electrode. The composition, modulus, strength and capacitance of the electrodes is measured in the initial state, after the first charge, and after 1000 charge/discharge cycles. Electrode modulus and strength increase with increasing CNT volume fraction; in contrast, the capacitance increases with increasing PANI mass. Charging or cycling reduce the electrode modulus and strength due to a decrease in CNT bundle volume fraction caused by swelling; the electrode capacitance also decreases due to a reduction in PANI mass. A micromechanical model is able to predict the stress-strain response of pre-charged and cycled electrodes, based upon their measured composition after pre-charging and cycling. The electrodes possess up to 63% of their theoretical capacitance, and their tensile strengths are comparable to those of engineering alloys. Their capacitance and strength decrease by less than 15% after the application of 1000 charge/discharge cycles. These properties illustrate their potential as structural energy storage devices.
△ Less
Submitted 16 June, 2021;
originally announced June 2021.
-
The influence of strut waviness on the tensile response of lattice materials
Authors:
P. E. Seiler,
K. Li,
V. S. Deshpande,
N. A. Fleck
Abstract:
Recent advances in additive manufacturing methods make it possible, for the first time, to manufacture complex micro-architectured solids that achieve desired stress versus strain responses. Here, we report experimental measurements and associated finite element (FE) calculations on the effect of strut shape upon the tensile response of two-dimensional (2D) lattices made from low-carbon steel shee…
▽ More
Recent advances in additive manufacturing methods make it possible, for the first time, to manufacture complex micro-architectured solids that achieve desired stress versus strain responses. Here, we report experimental measurements and associated finite element (FE) calculations on the effect of strut shape upon the tensile response of two-dimensional (2D) lattices made from low-carbon steel sheets. Two lattice topologies are considered: (i) a stretching-dominated triangular lattice and (ii) a bending-dominated hexagonal lattice. It is found that strut waviness can enhance the ductility of each lattice, particularly for bending-dominated hexagonal lattices. Manufacturing imperfections such as undercuts have a small effect on the ductility of the lattices but can significantly reduce the ultimate tensile strength. FE simulations provide additional insight into these observations and are used to construct design maps to aid the design of lattices with specified strength and ductility.
△ Less
Submitted 15 November, 2020;
originally announced November 2020.
-
Regulation of notch sensitivity of lattice materials by strut topology
Authors:
K. Li,
P. E. Seiler,
V. S. Deshpande,
N. A. Fleck
Abstract:
We propose a local reinforcement technique for lattices in the vicinity of a stress-raiser such as a notch, in order to elevate the macroscopic strength and ductility. A spatially non-uniform waviness distribution of sinusoidally-shaped struts is assumed in the vicinity of the notch, and the sensitivity of macroscopic tensile response to strut waviness distribution is studied by finite element ana…
▽ More
We propose a local reinforcement technique for lattices in the vicinity of a stress-raiser such as a notch, in order to elevate the macroscopic strength and ductility. A spatially non-uniform waviness distribution of sinusoidally-shaped struts is assumed in the vicinity of the notch, and the sensitivity of macroscopic tensile response to strut waviness distribution is studied by finite element analysis. Optimized lattice structures are determined in order to maximise the macroscopic tensile strength or ductility from these various strut waviness distributions. Both hexagonal and triangular lattices are studied as these geometries are representative of bending-dominated and stretching-dominated lattices, respectively.
△ Less
Submitted 12 October, 2020;
originally announced October 2020.
-
Mode II fracture of an MMA adhesive layer: theory versus experiment
Authors:
Sina Askarinejad,
Emilio Martínez-Pañeda,
I. Ivan Cuesta,
Norman A. Fleck
Abstract:
Thick adhesive layers have potential structural application in ship construction for the joining of a composite superstructure to a steel hull. The purpose of this study is to develop a mechanics model for the adhesive fracture of such lap joints under shear loading. Modified Thick-Adherend-Shear-Test (TAST) specimens made from a MMA-based adhesive and steel adherents are designed and fabricated.…
▽ More
Thick adhesive layers have potential structural application in ship construction for the joining of a composite superstructure to a steel hull. The purpose of this study is to develop a mechanics model for the adhesive fracture of such lap joints under shear loading. Modified Thick-Adherend-Shear-Test (TAST) specimens made from a MMA-based adhesive and steel adherents are designed and fabricated. Crack initiation and growth of these joints is measured and monitored by Digital Image Correlation (DIC). An attempt is made to use a cohesive zone model to predict the magnitude of shear strain across the adhesive layer both at crack initiation and at peak load, and to predict the extent of crack growth as a function of shear strain across the adhesive layer. The ability of a cohesive zone model to predict several features of specimen failure is assessed for the case of an adhesive layer of high shear ductility.
△ Less
Submitted 27 September, 2020;
originally announced September 2020.
-
An assessment of the J-integral test for a metallic foam
Authors:
H. C. Tankasala,
T. Li,
P. E. Seiler,
V. S. Deshpande,
N. A. Fleck
Abstract:
An assessment is made of the J-integral test procedure for initial crack growth in an open-cell aluminium alloy foam by combining finite element (FE) simulations with experiment. It is found experimentally that a zone of randomly failed struts develops ahead of the primary crack tip, and is comparable in size to that of the plastic zone. Hence, a crack tip J-field is absent at the initiation of cr…
▽ More
An assessment is made of the J-integral test procedure for initial crack growth in an open-cell aluminium alloy foam by combining finite element (FE) simulations with experiment. It is found experimentally that a zone of randomly failed struts develops ahead of the primary crack tip, and is comparable in size to that of the plastic zone. Hence, a crack tip J-field is absent at the initiation of crack growth from the primary crack tip. This implies that the measured J_IC value and the J versus crack extension Da curve cannot be treated as material properties despite the fact that the specimen size meets the usual criteria for J validity. The toughness tests were performed on a single-edge notched bend specimen, and crack extension was measured by the direct current potential drop method, by digital image correlation and by X-ray computed tomography. The crack growth resistance of the foam is associated with two distinct zones of plastic dissipation: (i) a bulk plastic zone emanating from the crack tip (containing a cluster of randomly failed struts), and (ii) a crack bridging zone behind the advancing crack tip. The applicability of a cohesive zone model to predict the fracture response is explored for the observed case of large scale bridging. To do so, FE simulations are performed by replacing the discrete lattice of the open-cell metallic foam by a compressible, elastic-plastic hardening solid while the fracture process zone in the foam is represented by a cohesive zone, as characterised by a tensile traction versus separation law. A detailed comparison of the cohesive zone model with experimental observations reveals that it is possible to capture the load versus displacement response but not the details of the fracture process zone using a single set of process zone parameters.
△ Less
Submitted 2 April, 2020;
originally announced April 2020.
-
The mechanics of solid-state nanofoaming
Authors:
Frederik Van Loock,
Victoria Bernardo,
Miguel Angel Rodríguez Pérez,
Norman A. Fleck
Abstract:
Solid-state nanofoaming experiments are conducted on two PMMA grades of markedly different molecular weight using CO$_2$ as the blowing agent. The sensitivity of porosity to foaming time and foaming temperature is measured. Also, the microstructure of the PMMA nanofoams is characterised in terms of cell size and cell nucleation density. A one dimensional numerical model is developed to predict the…
▽ More
Solid-state nanofoaming experiments are conducted on two PMMA grades of markedly different molecular weight using CO$_2$ as the blowing agent. The sensitivity of porosity to foaming time and foaming temperature is measured. Also, the microstructure of the PMMA nanofoams is characterised in terms of cell size and cell nucleation density. A one dimensional numerical model is developed to predict the growth of spherical, gas-filled voids during the solid-state foaming process. Diffusion of CO$_2$ within the PMMA matrix is sufficiently rapid for the concentration of CO$_2$ to remain almost uniform spatially. The foaming model makes use of experimentally calibrated constitutive laws for the uniaxial stress versus strain response of the PMMA grades as a function of strain rate and temperature, and the effect of dissolved CO$_2$ is accounted for by a shift in the glass transition temperature of the PMMA. The maximum achievable porosity is interpreted in terms of cell wall tearing and comparisons are made between the predictions of the model and nanofoaming measurements; it is deduced that the failure strain of the cell walls is sensitive to cell wall thickness.
△ Less
Submitted 17 September, 2019;
originally announced October 2019.
-
Mode II fracture of an elastic-plastic sandwich layer
Authors:
E. Martínez-Pañeda,
I. I. Cuesta,
N. A. Fleck
Abstract:
The shear strength of a pre-cracked sandwich layer is predicted, assuming that the layer is linear elastic or elastic-plastic, with yielding characterized by either J2 plasticity theory or by a strip-yield model. The substrates are elastic and of dissimilar modulus to that of the layer. Two geometries are analysed: (i) a semi-infinite crack in a sandwich layer, subjected to a remote mode II K-fiel…
▽ More
The shear strength of a pre-cracked sandwich layer is predicted, assuming that the layer is linear elastic or elastic-plastic, with yielding characterized by either J2 plasticity theory or by a strip-yield model. The substrates are elastic and of dissimilar modulus to that of the layer. Two geometries are analysed: (i) a semi-infinite crack in a sandwich layer, subjected to a remote mode II K-field and (ii) a centre-cracked sandwich plate of finite width under remote shear stress. For the semi-infinite crack, the near tip stress field is determined as a function of elastic mismatch, and crack tip plasticity is either prevented (the elastic case) or is duly accounted for (the elastic-plastic case). Analytical and numerical solutions are then obtained for the centre-cracked sandwich plate of finite width. First, a mode II K-calibration is obtained for a finite crack in the elastic sandwich layer. Second, the analysis is extended to account for crack tip plasticity via a mode II strip-yield model of finite strength and of finite toughness. The analytical predictions are verified by finite element simulations and a failure map is constructed in terms of specimen geometry and crack length.
△ Less
Submitted 9 September, 2019;
originally announced September 2019.
-
Creep failure of honeycombs made by rapid prototy**
Authors:
P. E. Seiler,
H. C. Tankasala,
N. A. Fleck
Abstract:
Additive manufacture and rapid prototy** are versatile methods for the generation of lattice materials for applications in the creep regime. However, these techniques introduce defects that can degrade the macro-scopic creep strength. In the present study, the uniaxial tensile response of two-dimensional PMMA lattices is measured in the visco-plastic regime: tests are performed at 100C which is…
▽ More
Additive manufacture and rapid prototy** are versatile methods for the generation of lattice materials for applications in the creep regime. However, these techniques introduce defects that can degrade the macro-scopic creep strength. In the present study, the uniaxial tensile response of two-dimensional PMMA lattices is measured in the visco-plastic regime: tests are performed at 100C which is slightly below the glass transition temperature T g of PMMA. Both as-manufactured defects (Plateau borders and strut thickness variation) and as-designed defects (missing cell walls, solid inclusions, and randomly perturbed joints) are introduced. The dispersion in macroscopic strength is measured for relative densities in the range of 0.07 to 0.19. It is observed that initial failure of the lattice is diffuse in nature: struts fail at a number of uncorrelated locations, followed by the development of a single macroscopic crack transverse to the loading direction. In contrast, the same PMMA lattice fails in a correlated, brittle manner at room temperature. An FE study is performed to gain insight into the diffuse failure mode and the role played by as-manufactured defects, including the dispersion in tensile strength of individual struts of the lattice. A high damage tolerance to as-designed defects is observed experimentally: there is negligible knock-down in strength due to the removal of cell walls or to the presence of solid inclusions. These findings aid the design and manufacture of damage tolerant lattices in the creep regime.
△ Less
Submitted 7 August, 2019;
originally announced August 2019.
-
Mechanical properties of PMMA sepiolite nanocellular materials with a bimodal cellular structure
Authors:
Victoria Bernardo,
Frederik Van Loock,
Judith Martin de Leon,
Norman A. Fleck,
Miguel Angel Rodriguez Perez
Abstract:
Bimodal cellular poly(methyl methacrylate) with micron and nano sized (300 to 500 nm) cells with up to 5 weight percent of sepiolite nanoparticles and porosity from 50 weight percent to 75 weight percent are produced by solid state foaming. Uniaxial compression tests are performed to measure the effect of sepiolite concentration on the elastic modulus and the yield strength of the solid and cellul…
▽ More
Bimodal cellular poly(methyl methacrylate) with micron and nano sized (300 to 500 nm) cells with up to 5 weight percent of sepiolite nanoparticles and porosity from 50 weight percent to 75 weight percent are produced by solid state foaming. Uniaxial compression tests are performed to measure the effect of sepiolite concentration on the elastic modulus and the yield strength of the solid and cellular nanocomposites. Single edge notch bend tests are conducted to relate the fracture toughness of the solid and cellular nanocomposites to sepiolite concentration. The relative modulus is independent of sepiolite content to within material scatter when considering the complete porosity range. In contrast, a mild enhancement of the relative modulus is observed by the addition of sepiolite particles for the foamed nanocomposites with a porosity close to 50 percent. The relative compressive strength of the cellular nanocomposites mildly decreases as a function of sepiolite concentration. A strong enhancement of the relative fracture toughness by the addition of sepiolites is observed. The enhancement of the relative fracture toughness and the relative modulus (at 50 percent porosity) can be attributed to an improved dispersion of the particles due to foaming and the migration of micron sized aggregates from the solid phase to the microcellular pores during foaming.
△ Less
Submitted 8 July, 2019;
originally announced July 2019.
-
Deformation and failure maps for PMMA in uniaxial tension
Authors:
Frederik Van Loock,
Norman A. Fleck
Abstract:
Uniaxial tensile tests are performed on a polymethyl methacrylate (PMMA) grade over a range of temperatures near the glass transition and over two decades of strain rate. Deformation maps are constructed for Young's modulus, flow strength, and failure strain as a function of temperature for selected strain rates. The glassy, glass transition and rubbery regimes are identified, and constitutive rel…
▽ More
Uniaxial tensile tests are performed on a polymethyl methacrylate (PMMA) grade over a range of temperatures near the glass transition and over two decades of strain rate. Deformation maps are constructed for Young's modulus, flow strength, and failure strain as a function of temperature for selected strain rates. The glassy, glass transition and rubbery regimes are identified, and constitutive relations are calibrated for the modulus and flow strength within each regime.
△ Less
Submitted 8 July, 2019;
originally announced July 2019.
-
The mechanical and electrical properties of direct-spun carbon nanotube mat-epoxy composites
Authors:
Wei Tan,
Joe C. Stallard,
Fiona R. Smail,
Adam M. Boies,
Norman A. Fleck
Abstract:
Composites of direct-spun carbon nanotube (CNT) mats and epoxy are manufactured and tested in order to determine their mechanical and electrical properties. The mats are spun directly from a floating catalyst, chemical vapour deposition reactor. The volume fraction of epoxy is varied widely by suitable dilution of the epoxy resin with acetone. Subsequent evaporation of the acetone, followed by a c…
▽ More
Composites of direct-spun carbon nanotube (CNT) mats and epoxy are manufactured and tested in order to determine their mechanical and electrical properties. The mats are spun directly from a floating catalyst, chemical vapour deposition reactor. The volume fraction of epoxy is varied widely by suitable dilution of the epoxy resin with acetone. Subsequent evaporation of the acetone, followed by a cure cycle, leads to composites of varying volume fraction of CNT, epoxy and air. The modulus, strength, electrical conductivity and piezoresistivity of the composites are measured. The CNT mats and their composites exhibit an elastic-plastic stress-strain response under uniaxial tensile loading, and the degree of anisotropy is assessed by testing specimens in 0°, 45° and 90° directions with respect to the draw direction of mat manufacture. The electrical conductivity scales linearly with CNT volume fraction, irrespective of epoxy volume fraction. In contrast, the modulus and strength depend upon both CNT and epoxy volume fractions in a non-linear manner. The macroscopic moduli of the CNT mat-epoxy composites are far below the Voigt bound based on the modulus of CNT walls and epoxy. A micromechanical model is proposed to relate the macroscopic modulus and yield strength of a CNT mat-epoxy composite to the microstructure.
△ Less
Submitted 20 May, 2019;
originally announced May 2019.
-
The role of defects in dictating the strength of brittle honeycombs made by rapid prototy**
Authors:
P. E. Seiler,
H. C. Tankasala,
N. A. Fleck
Abstract:
Rapid prototy** is an emerging technology for the fast make of engineering components. A common technique is to laser cut a two-dimensional (2D) part from polymethyl methacrylate (PMMA) sheet. However, both manufacturing defects and design defects (such as stress raisers) exist in the part, and these degrade its strength. In the present study, a combination of experiment and finite element analy…
▽ More
Rapid prototy** is an emerging technology for the fast make of engineering components. A common technique is to laser cut a two-dimensional (2D) part from polymethyl methacrylate (PMMA) sheet. However, both manufacturing defects and design defects (such as stress raisers) exist in the part, and these degrade its strength. In the present study, a combination of experiment and finite element analysis is used to determine the sensitivity of the tensile strength of PMMA hexagonal lattices to both as-manufactured and as-designed defects. The as-manufactured defects include variations in strut thickness and in Plateau border radius. The knockdown in lattice tensile strength is measured for lattice relative density in the range of 0.07 to 0.19. A systematic finite element (FE) study is performed to assess the explicit role of each type of as-manufactured defect on the lattice strength. As-designed defects such as randomly perturbed joints, missing cells, and solid inclusions are introduced within a regular hexagonal lattice. The notion of a transition flaw size is used to quantify the sensitivity of lattice strength to defect size.
△ Less
Submitted 3 May, 2019; v1 submitted 23 April, 2019;
originally announced April 2019.
-
Mode I crack tip fields: strain gradient plasticity theory versus J2 flow theory
Authors:
Emilio Martínez-Pañeda,
Norman A. Fleck
Abstract:
The mode I crack tip asymptotic response of a solid characterised by strain gradient plasticity is investigated. It is found that elastic strains dominate plastic strains near the crack tip, and thus the Cauchy stress and the strain state are given asymptotically by the elastic K-field. This crack tip elastic zone is embedded within an annular elasto-plastic zone. This feature is predicted by both…
▽ More
The mode I crack tip asymptotic response of a solid characterised by strain gradient plasticity is investigated. It is found that elastic strains dominate plastic strains near the crack tip, and thus the Cauchy stress and the strain state are given asymptotically by the elastic K-field. This crack tip elastic zone is embedded within an annular elasto-plastic zone. This feature is predicted by both a crack tip asymptotic analysis and a finite element computation. When small scale yielding applies, three distinct regimes exist: an outer elastic K field, an intermediate elasto-plastic field, and an inner elastic K field. The inner elastic core significantly influences the crack opening profile. Crack tip plasticity is suppressed when the material length scale $\ell$ of the gradient theory is on the order of the plastic zone size estimation, as dictated by the remote stress intensity factor. A generalized J-integral for strain gradient plasticity is stated and used to characterise the asymptotic response ahead of a short crack. Finite element analysis of a cracked three point bend specimen reveals that the crack tip elastic zone persists in the presence of bulk plasticity and an outer J-field.
△ Less
Submitted 13 February, 2019;
originally announced February 2019.
-
The role of plastic strain gradients in the crack growth resistance of metals
Authors:
Emilio Martínez-Pañeda,
Vikram S. Deshpande,
Christian F. Niordson,
Norman A. Fleck
Abstract:
Crack advance from short or long pre-cracks is predicted by the progressive failure of a cohesive zone in a strain gradient, elasto-plastic solid. The presence of strain gradients leads to the existence of an elastic zone at the tip of a stationary crack, for both the long crack and the short crack cases. This is in sharp contrast with previous asymptotic analyses of gradient solids, where elastic…
▽ More
Crack advance from short or long pre-cracks is predicted by the progressive failure of a cohesive zone in a strain gradient, elasto-plastic solid. The presence of strain gradients leads to the existence of an elastic zone at the tip of a stationary crack, for both the long crack and the short crack cases. This is in sharp contrast with previous asymptotic analyses of gradient solids, where elastic strains were neglected. The presence of an elastic singularity at the crack tip generates stresses which are sufficiently high to activate quasi-cleavage. For the long crack case, crack growth resistance curves are predicted for a wide range of ratios of cohesive zone strength to yield strength. Remarkably, this feature of an elastic singularity is preserved for short cracks, leading to a severe reduction in tensile ductility. In qualitative terms, these predictions resemble those of discrete dislocation calculations, including the concept of a dislocation-free zone at the crack tip.
△ Less
Submitted 10 February, 2019;
originally announced February 2019.
-
Compressive Behavior and Failure Mechanisms of Freestanding and Composite 3D Graphitic Foams
Authors:
Kenichi Nakanishi,
Adrianus I. Aria,
Matthew Berwind,
Robert S. Weatherup,
Christoph Eberl,
Stephan Hofmann,
Norman A. Fleck
Abstract:
Open-cell graphitic foams were fabricated by chemical vapor deposition using nickel templates and their compressive responses were measured over a range of relative densities. The mechanical response required an interpretation in terms of a hierarchical micromechanical model, spanning 3 distinct length scales. The power law scaling of elastic modulus and yield strength versus relative density sugg…
▽ More
Open-cell graphitic foams were fabricated by chemical vapor deposition using nickel templates and their compressive responses were measured over a range of relative densities. The mechanical response required an interpretation in terms of a hierarchical micromechanical model, spanning 3 distinct length scales. The power law scaling of elastic modulus and yield strength versus relative density suggests that the cell walls of the graphitic foam deform by bending. The length scale of the unit cell of the foam is set by the length of the struts comprising the cell wall, and is termed level I. The cell walls comprise hollow triangular tubes, and bending of these strut-like tubes involves axial stretching of the tube walls. This length scale is termed level II. In turn, the tube walls form a wavy stack of graphitic layers, and this waviness induces interlayer shear of the graphitic layers when the tube walls are subjected to axial stretch. The thickness of the tube wall defines the third length scale, termed level III. We show that the addition of a thin, flexible ceramic Al2O3 scaffold stiffens and strengthens the foam, yet preserves the power law scaling. The hierarchical model gives fresh insight into the mechanical properties of foams with cell walls made from emergent 2D layered solids.
△ Less
Submitted 11 December, 2018;
originally announced December 2018.
-
On the geometric stability of an inorganic nanowire and an organic ligand shell
Authors:
Simon Bettscheider,
Tobias Kraus,
Norman A. Fleck
Abstract:
The break-up of a nanowire with an organic ligand shell into discrete droplets is analysed in terms of the Rayleigh-Plateau instability. Explicit account is taken of the effect of the organic ligand shell upon the energetics and kinetics of surface diffusion in the wire. Both an initial perturbation analysis and a full numerical analysis of the evolution in wire morphology are conducted, and the g…
▽ More
The break-up of a nanowire with an organic ligand shell into discrete droplets is analysed in terms of the Rayleigh-Plateau instability. Explicit account is taken of the effect of the organic ligand shell upon the energetics and kinetics of surface diffusion in the wire. Both an initial perturbation analysis and a full numerical analysis of the evolution in wire morphology are conducted, and the governing non-dimensional groups are identified. The perturbation analysis is remarkably accurate in obtaining the main features of the instability, including the pinch-off time and the resulting diameter of the droplets. It is conjectured that the surface energy of the wire and surrounding organic shell depends upon both the mean and deviatoric invariants of the curvature tensor. Such a behaviour allows for the possibility of a stable nanowire such that the Rayleigh-Plateau instability is not energetically favourable. A stability map illustrates this. Maps are also constructed for the final droplet size and pinch-off time as a function of two non-dimensional groups that characterise the energetics and kinetics of diffusion in the presence of the organic shell. These maps can guide future experimental activity on the stabilisation of nanowires by organic ligand shells.
△ Less
Submitted 2 August, 2018;
originally announced August 2018.
-
Crack growth resistance in metallic alloys: the role of isotropic versus kinematic hardening
Authors:
Emilio Martínez-Pañeda,
Norman A. Fleck
Abstract:
The sensitivity of crack growth resistance to the choice of isotropic or kinematic hardening is investigated. Monotonic mode I crack advance under small scale yielding conditions is modelled via a cohesive zone formulation endowed with a traction-separation law. R-curves are computed for materials that exhibit linear or power law hardening. Kinematic hardening leads to an enhanced crack growth res…
▽ More
The sensitivity of crack growth resistance to the choice of isotropic or kinematic hardening is investigated. Monotonic mode I crack advance under small scale yielding conditions is modelled via a cohesive zone formulation endowed with a traction-separation law. R-curves are computed for materials that exhibit linear or power law hardening. Kinematic hardening leads to an enhanced crack growth resistance relative to isotropic hardening. Moreover, kinematic hardening requires greater crack extension to achieve the steady state. These differences are traced to the non-proportional loading of material elements near the crack tip as the crack advances. The sensitivity of the R-curve to the cohesive zone properties and to the level of material strain hardening is explored for both isotropic and kinematic hardening.
△ Less
Submitted 23 June, 2018;
originally announced June 2018.
