Showing 1–14 of 14 results for author: Eno, S C

Using graph neural networks to reconstruct charged pion showers in the CMS High Granularity Calorimeter

Authors: M. Aamir, B. Acar, G. Adamov, T. Adams, C. Adloff, S. Afanasiev, C. Agrawal, C. Agrawal, A. Ahmad, H. A. Ahmed, S. Akbar, N. Akchurin, B. Akgul, B. Akgun, R. O. Akpinar, E. Aktas, A. AlKadhim, V. Alexakhin, J. Alimena, J. Alison, A. Alpana, W. Alshehri, P. Alvarez Dominguez, M. Alyari, C. Amendola , et al. (550 additional authors not shown)

Abstract: A novel method to reconstruct the energy of hadronic showers in the CMS High Granularity Calorimeter (HGCAL) is presented. The HGCAL is a sampling calorimeter with very fine transverse and longitudinal granularity. The active media are silicon sensors and scintillator tiles readout by SiPMs and the absorbers are a combination of lead and Cu/CuW in the electromagnetic section, and steel in the hadr… ▽ More A novel method to reconstruct the energy of hadronic showers in the CMS High Granularity Calorimeter (HGCAL) is presented. The HGCAL is a sampling calorimeter with very fine transverse and longitudinal granularity. The active media are silicon sensors and scintillator tiles readout by SiPMs and the absorbers are a combination of lead and Cu/CuW in the electromagnetic section, and steel in the hadronic section. The shower reconstruction method is based on graph neural networks and it makes use of a dynamic reduction network architecture. It is shown that the algorithm is able to capture and mitigate the main effects that normally hinder the reconstruction of hadronic showers using classical reconstruction methods, by compensating for fluctuations in the multiplicity, energy, and spatial distributions of the shower's constituents. The performance of the algorithm is evaluated using test beam data collected in 2018 prototype of the CMS HGCAL accompanied by a section of the CALICE AHCAL prototype. The capability of the method to mitigate the impact of energy leakage from the calorimeter is also demonstrated. △ Less

Submitted 30 June, 2024; v1 submitted 17 June, 2024; originally announced June 2024.

Comments: Prepared for submission to JINST

Effects of oxygen on the optical properties of phenyl-based scintillators during irradiation and recovery

Authors: C. Papageorgakis, M. Y. Aamir, A. Belloni, T. K. Edberg, S. C. Eno, B. Kronheim, C. Palmer

Abstract: Plastic scintillators are a versatile and inexpensive option for particle detection, which is why the largest particle physics experiments, CMS and ATLAS, use them extensively in their calorimeters. One of their challenging aspects, however, is their relatively low radiation hardness, which might be inadequate for very high luminosity future projects like the FCC-hh. In this study, results on the… ▽ More Plastic scintillators are a versatile and inexpensive option for particle detection, which is why the largest particle physics experiments, CMS and ATLAS, use them extensively in their calorimeters. One of their challenging aspects, however, is their relatively low radiation hardness, which might be inadequate for very high luminosity future projects like the FCC-hh. In this study, results on the effects of ionizing radiation on the optical properties of plastic scintillator samples are presented. The samples are made from two different matrix materials, polystyrene and polyvinyltoluene, and have been irradiated at dose rates ranging from $2.2\,$Gy/h up to $3.4\,$kGy/h at room temperature. An internal boundary that separates two regions of different indices of refraction is visible in the samples depending on the dose rate, and it is compatible with the expected oxygen penetration depth during irradiation. The dose rate dependence of the oxygen penetration depth for the two matrix materials suggests that the oxygen penetration coefficient differs for PS and PVT. The values of the refractive index for the internal regions are elevated compared to those of the outer regions, which are compatible with the indices of unirradiated samples. △ Less

Submitted 8 December, 2023; v1 submitted 23 October, 2023; originally announced October 2023.

Comments: Replaced with published version. Added journal DOI. 30 pages, 15 figures. Published in Nuclear Instruments and Methods in Physics Research Section A

Journal ref: Nucl. Instrum. Methods Phys. Res. A 1059 (2024) 168977

Reduction of light output of plastic scintillator tiles during irradiation at cold temperatures and in low-oxygen environments

Authors: B. Kronheim, A. Belloni, T. K. Edberg, S. C. Eno, C. Howe, C. Palmer, C. Papageorgakis, M. Paranjpe, S. Sriram

Abstract: The advent of the silicon photomultiplier has allowed the development of highly segmented calorimeters using plastic scintillator as the active media, with photodetectors embedded in the calorimeter, in dimples in the plastic. To reduce the photodetector's dark current and radiation damage, the high granularity calorimeter designed for the high luminosity upgrade of the CMS detector at CERN's Larg… ▽ More The advent of the silicon photomultiplier has allowed the development of highly segmented calorimeters using plastic scintillator as the active media, with photodetectors embedded in the calorimeter, in dimples in the plastic. To reduce the photodetector's dark current and radiation damage, the high granularity calorimeter designed for the high luminosity upgrade of the CMS detector at CERN's Large Hadron Collider will be operated at a temperature of about -30$^\circ$C. Due to flammability considerations, a low oxygen environment is being considered. However, the radiation damage to the plastic scintillator during irradiation in this operating environment needs to be considered. In this paper, we present measurements of the relative decrease of light output during irradiation of small plastic scintillator tiles read out by silicon photomultipliers. The irradiations were performed using a $^{60}\mathrm{Co}$ source both to produce the tiles' light and as a source of ionizing irradiation at dose rates of 0.3, 1.3, and $1.6\,$Gy/hr, temperatures of -30, -15, -5, and 0$^\circ$C, and with several different oxygen concentrations in the surrounding atmosphere. The effect of the material used to wrap the tile was also studied. Substantial temporary damage, which annealed when the sample was warmed, was seen during the low-temperature irradiations, regardless of the oxygen concentration and wrap** material. The relative light loss was largest with 3M$^{\tiny \textrm{TM}}$ Enhanced Specular Reflector Film wrap** and smallest with no wrap**, although due to the substantially higher light yield with wrap**, the final light output is largest with wrap**. The light loss was less at warmer temperatures. Damage with $3\%$ oxygen was similar to that in standard atmosphere. Evidence of a plateau in the radical density was seen for the 0$^\circ$C data. △ Less

Submitted 3 August, 2023; originally announced August 2023.

Journal ref: Nucl. Instrum. Methods Phys. Res. A 1059 (2024) 168922

Performance of the CMS High Granularity Calorimeter prototype to charged pion beams of 20$-$300 GeV/c

Authors: B. Acar, G. Adamov, C. Adloff, S. Afanasiev, N. Akchurin, B. Akgün, M. Alhusseini, J. Alison, J. P. Figueiredo de sa Sousa de Almeida, P. G. Dias de Almeida, A. Alpana, M. Alyari, I. Andreev, U. Aras, P. Aspell, I. O. Atakisi, O. Bach, A. Baden, G. Bakas, A. Bakshi, S. Banerjee, P. DeBarbaro, P. Bargassa, D. Barney, F. Beaudette , et al. (435 additional authors not shown)

Abstract: The upgrade of the CMS experiment for the high luminosity operation of the LHC comprises the replacement of the current endcap calorimeter by a high granularity sampling calorimeter (HGCAL). The electromagnetic section of the HGCAL is based on silicon sensors interspersed between lead and copper (or copper tungsten) absorbers. The hadronic section uses layers of stainless steel as an absorbing med… ▽ More The upgrade of the CMS experiment for the high luminosity operation of the LHC comprises the replacement of the current endcap calorimeter by a high granularity sampling calorimeter (HGCAL). The electromagnetic section of the HGCAL is based on silicon sensors interspersed between lead and copper (or copper tungsten) absorbers. The hadronic section uses layers of stainless steel as an absorbing medium and silicon sensors as an active medium in the regions of high radiation exposure, and scintillator tiles directly readout by silicon photomultipliers in the remaining regions. As part of the development of the detector and its readout electronic components, a section of a silicon-based HGCAL prototype detector along with a section of the CALICE AHCAL prototype was exposed to muons, electrons and charged pions in beam test experiments at the H2 beamline at the CERN SPS in October 2018. The AHCAL uses the same technology as foreseen for the HGCAL but with much finer longitudinal segmentation. The performance of the calorimeters in terms of energy response and resolution, longitudinal and transverse shower profiles is studied using negatively charged pions, and is compared to GEANT4 predictions. This is the first report summarizing results of hadronic showers measured by the HGCAL prototype using beam test data. △ Less

Submitted 27 May, 2023; v1 submitted 9 November, 2022; originally announced November 2022.

Comments: Accepted for publication by JINST

Dose rate effects in radiation-induced changes to phenyl-based polymeric scintillators

Authors: Christos Papageorgakis, Mohamad Al-Sheikhly, Alberto Belloni, Timothy K. Edberg, Sarah C. Eno, Yongbin Feng, Geng-Yuan Jeng, Abraham Kahn, Yihui Lai, Tyler McDonnell, Christopher Palmer, Ruhi Perez-Gokhale, Francesca Ricci-Tam, Yao Yao, Zishuo Yang

Abstract: Results on the effects of ionizing radiation on the signal produced by plastic scintillating rods manufactured by Eljen Technology company are presented for various matrix materials, dopant concentrations, fluors (EJ-200 and EJ-260), anti-oxidant concentrations, scintillator thickness, doses, and dose rates. The light output before and after irradiation is measured using an alpha source and a phot… ▽ More Results on the effects of ionizing radiation on the signal produced by plastic scintillating rods manufactured by Eljen Technology company are presented for various matrix materials, dopant concentrations, fluors (EJ-200 and EJ-260), anti-oxidant concentrations, scintillator thickness, doses, and dose rates. The light output before and after irradiation is measured using an alpha source and a photomultiplier tube, and the light transmission by a spectrophotometer. Assuming an exponential decrease in the light output with dose, the change in light output is quantified using the exponential dose constant $D$. The $D$ values are similar for primary and secondary do** concentrations of 1 and 2 times, and for antioxidant concentrations of 0, 1, and 2 times, the default manufacturer's concentration. The $D$ value depends approximately linearly on the logarithm of the dose rate for dose rates between 2.2 Gy/hr and 70 Gy/hr for all materials. For EJ-200 polyvinyltoluene-based (PVT) scintillator, the dose constant is approximately linear in the logarithm of the dose rate up to 3400 Gy/hr, while for polystyrene-based (PS) scintillator or for both materials with EJ-260 fluors, it remains constant or decreases (depending on do** concentration) above about 100 Gy/hr. The results from rods of varying thickness and from the different fluors suggest damage to the initial light output is a larger effect than color center formation for scintillator thickness $\leq1$ cm. For the blue scintillator (EJ-200), the transmission measurements indicate damage to the fluors. We also find that while PVT is more resistant to radiation damage than PS at dose rates higher than about 100 Gy/hr for EJ-200 fluors, they show similar damage at lower dose rates and for EJ-260 fluors. △ Less

Submitted 8 August, 2023; v1 submitted 29 March, 2022; originally announced March 2022.

Comments: Replaced with published version. Added journal DOI. 24 pages, 11 figures, Published in Nuclear Instruments and Methods in Physics Research Section A

Journal ref: Nucl. Instrum. Methods Phys. Res. A 1042 (2022) 167445

Precision timing for collider-experiment-based calorimetry

Authors: S. V. Chekanov, F. Simon, V. Boudry, W. Chung, P. W. Gorham, M. Nguyen, C. G. Tully, S. C. Eno, Y. Lai, A. V. Kotwal, S. Ko, I. Laktineh, S. Lee, J. S. H. Lee, M. T. Lucchini, R. Prechelt, H. Yoo, C. -H Yeh, S. -S. Yu, G. S. Varner, R. Zhu

Abstract: In this White Paper for the 2021 Snowmass process, we discuss aspects of precision timing within electromagnetic and hadronic calorimeter systems for high-energy physics collider experiments. Areas of applications include particle identification, event and object reconstruction, and pileup mitigation. Two different system options are considered, namely cell-level timing capabilities covering the f… ▽ More In this White Paper for the 2021 Snowmass process, we discuss aspects of precision timing within electromagnetic and hadronic calorimeter systems for high-energy physics collider experiments. Areas of applications include particle identification, event and object reconstruction, and pileup mitigation. Two different system options are considered, namely cell-level timing capabilities covering the full detector volume, and dedicated timing layers integrated in calorimeter systems. A selection of technologies for the different approaches is also discussed. △ Less

Submitted 14 March, 2022; originally announced March 2022.

Comments: 22 pages, 9 figures, Editors: S. V. Chekanov, F. Simon. Submitted to the Proceedings of the US Community Study on the Future of Particle Physics (Snowmass 2021)

Report number: ANL-HEP-173859, MPP-2022-28

Higgs Factory Considerations

Authors: J. A. Bagger, B. C. Barish, S. Belomestnykh, P. C. Bhat, J. E. Brau, M. Demarteau, D. Denisov, S. C. Eno, C. G. R. Geddes, P. D. Grannis, A. Hutton, A. J. Lankford, M. U. Liepe, D. B. MacFarlane, T. Markiewicz, H. E. Montgomery, J. R. Patterson, M. Perelstein, M. E. Peskin, M. C. Ross, J. Strube, A. P. White, G. W. Wilson

Abstract: We discuss considerations that can be used to formulate recommendations for initiating a lepton collider project that would provide precision studies of the Higgs boson and related electroweak phenomena. We discuss considerations that can be used to formulate recommendations for initiating a lepton collider project that would provide precision studies of the Higgs boson and related electroweak phenomena. △ Less

Submitted 17 March, 2022; v1 submitted 11 March, 2022; originally announced March 2022.

Comments: contribution to Snowmass 2021

Response of a CMS HGCAL silicon-pad electromagnetic calorimeter prototype to 20-300 GeV positrons

Authors: B. Acar, G. Adamov, C. Adloff, S. Afanasiev, N. Akchurin, B. Akgün, F. Alam Khan, M. Alhusseini, J. Alison, A. Alpana, G. Altopp, M. Alyari, S. An, S. Anagul, I. Andreev, P. Aspell, I. O. Atakisi, O. Bach, A. Baden, G. Bakas, A. Bakshi, S. Bannerjee, P. Bargassa, D. Barney, F. Beaudette , et al. (364 additional authors not shown)

Abstract: The Compact Muon Solenoid Collaboration is designing a new high-granularity endcap calorimeter, HGCAL, to be installed later this decade. As part of this development work, a prototype system was built, with an electromagnetic section consisting of 14 double-sided structures, providing 28 sampling layers. Each sampling layer has an hexagonal module, where a multipad large-area silicon sensor is glu… ▽ More The Compact Muon Solenoid Collaboration is designing a new high-granularity endcap calorimeter, HGCAL, to be installed later this decade. As part of this development work, a prototype system was built, with an electromagnetic section consisting of 14 double-sided structures, providing 28 sampling layers. Each sampling layer has an hexagonal module, where a multipad large-area silicon sensor is glued between an electronics circuit board and a metal baseplate. The sensor pads of approximately 1 cm$^2$ are wire-bonded to the circuit board and are readout by custom integrated circuits. The prototype was extensively tested with beams at CERN's Super Proton Synchrotron in 2018. Based on the data collected with beams of positrons, with energies ranging from 20 to 300 GeV, measurements of the energy resolution and linearity, the position and angular resolutions, and the shower shapes are presented and compared to a detailed Geant4 simulation. △ Less

Submitted 31 March, 2022; v1 submitted 12 November, 2021; originally announced November 2021.

Construction and commissioning of CMS CE prototype silicon modules

Authors: B. Acar, G. Adamov, C. Adloff, S. Afanasiev, N. Akchurin, B. Akgün, M. Alhusseini, J. Alison, G. Altopp, M. Alyari, S. An, S. Anagul, I. Andreev, M. Andrews, P. Aspell, I. A. Atakisi, O. Bach, A. Baden, G. Bakas, A. Bakshi, P. Bargassa, D. Barney, E. Becheva, P. Behera, A. Belloni , et al. (307 additional authors not shown)

Abstract: As part of its HL-LHC upgrade program, the CMS Collaboration is develo** a High Granularity Calorimeter (CE) to replace the existing endcap calorimeters. The CE is a sampling calorimeter with unprecedented transverse and longitudinal readout for both electromagnetic (CE-E) and hadronic (CE-H) compartments. The calorimeter will be built with $\sim$30,000 hexagonal silicon modules. Prototype modul… ▽ More As part of its HL-LHC upgrade program, the CMS Collaboration is develo** a High Granularity Calorimeter (CE) to replace the existing endcap calorimeters. The CE is a sampling calorimeter with unprecedented transverse and longitudinal readout for both electromagnetic (CE-E) and hadronic (CE-H) compartments. The calorimeter will be built with $\sim$30,000 hexagonal silicon modules. Prototype modules have been constructed with 6-inch hexagonal silicon sensors with cell areas of 1.1~$cm^2$, and the SKIROC2-CMS readout ASIC. Beam tests of different sampling configurations were conducted with the prototype modules at DESY and CERN in 2017 and 2018. This paper describes the construction and commissioning of the CE calorimeter prototype, the silicon modules used in the construction, their basic performance, and the methods used for their calibration. △ Less

Submitted 10 December, 2020; originally announced December 2020.

Comments: 35 pages, submitted to JINST

The DAQ system of the 12,000 Channel CMS High Granularity Calorimeter Prototype

Authors: B. Acar, G. Adamov, C. Adloff, S. Afanasiev, N. Akchurin, B. Akgün, M. Alhusseini, J. Alison, G. Altopp, M. Alyari, S. An, S. Anagul, I. Andreev, M. Andrews, P. Aspell, I. A. Atakisi, O. Bach, A. Baden, G. Bakas, A. Bakshi, P. Bargassa, D. Barney, E. Becheva, P. Behera, A. Belloni , et al. (307 additional authors not shown)

Abstract: The CMS experiment at the CERN LHC will be upgraded to accommodate the 5-fold increase in the instantaneous luminosity expected at the High-Luminosity LHC (HL-LHC). Concomitant with this increase will be an increase in the number of interactions in each bunch crossing and a significant increase in the total ionising dose and fluence. One part of this upgrade is the replacement of the current endca… ▽ More The CMS experiment at the CERN LHC will be upgraded to accommodate the 5-fold increase in the instantaneous luminosity expected at the High-Luminosity LHC (HL-LHC). Concomitant with this increase will be an increase in the number of interactions in each bunch crossing and a significant increase in the total ionising dose and fluence. One part of this upgrade is the replacement of the current endcap calorimeters with a high granularity sampling calorimeter equipped with silicon sensors, designed to manage the high collision rates. As part of the development of this calorimeter, a series of beam tests have been conducted with different sampling configurations using prototype segmented silicon detectors. In the most recent of these tests, conducted in late 2018 at the CERN SPS, the performance of a prototype calorimeter equipped with ${\approx}12,000\rm{~channels}$ of silicon sensors was studied with beams of high-energy electrons, pions and muons. This paper describes the custom-built scalable data acquisition system that was built with readily available FPGA mezzanines and low-cost Raspberry PI computers. △ Less

Submitted 8 December, 2020; v1 submitted 7 December, 2020; originally announced December 2020.

New perspectives on segmented crystal calorimeters for future colliders

Authors: Marco T. Lucchini, Wonyong Chung, Sarah C. Eno, Yihui Lai, Lorenzo Lucchini, Minh-Thi Nguyen, Christopher G. Tully

Abstract: Crystal calorimeters have a long history of pushing the frontier on high-resolution electromagnetic (EM) calorimetry. We explore in this paper major innovations in collider detector performance that can be achieved with crystal calorimetry when longitudinal segmentation and dual-readout capabilities are combined with a new high EM resolution approach to PFA in multi-jet events, such as… ▽ More Crystal calorimeters have a long history of pushing the frontier on high-resolution electromagnetic (EM) calorimetry. We explore in this paper major innovations in collider detector performance that can be achieved with crystal calorimetry when longitudinal segmentation and dual-readout capabilities are combined with a new high EM resolution approach to PFA in multi-jet events, such as $e^+e^+\rightarrow HZ$ events in all-hadronic final-states at Higgs factories. We demonstrate a new technique for pre-processing $π^0$ momenta through combinatoric di-photon pairing in advance of applying jet algorithms. This procedure significantly reduces $π^0$ photon splitting across jets in multi-jet events. The correct photon-to-jet assignment efficiency improves by a factor of 3 with a $3\%/\sqrt{E}$ EM resolution. In addition, the technique of bremsstrahlung photon recovery significantly improves electron momentum measurements. A high EM resolution calorimeter increases the Z boson recoil mass resolution in Higgstrahlung events for decays into electron pairs to 80% of that for muon pairs. We present the design and optimization of a highly segmented crystal detector concept that achieves the required energy resolution, and a time resolution better than 30 ps providing exceptional particle identification capabilities. We demonstrate that, contrary to previous detector designs that suffered from large neutral hadron resolution degradation from one interaction length of crystals in front of a sampling hadron calorimeter, the implementation of dual-readout on crystals permits to achieve a resolution better than $30\%/\sqrt{E}\oplus 2\%$ for neutral hadrons. Our studies find that the integration of crystal calorimetry into future Higgs factory collider detectors can open new perspectives by yielding the highest level of combined EM and neutral hadron resolution in the PFA paradigm. △ Less

Submitted 15 September, 2020; v1 submitted 1 August, 2020; originally announced August 2020.

Journal ref: 2020 JINST 15 P11005

MATHUSLA: A Detector Proposal to Explore the Lifetime Frontier at the HL-LHC

Authors: Henry Lubatti, Cristiano Alpigiani, Juan Carlos Arteaga-Velázquez, Austin Ball, Liron Barak James Beacham, Yan Benhammo, Karen Salomé Caballero-Mora, Paolo Camarri, Tingting Cao, Roberto Cardarelli, John Paul Chou, David Curtin, Albert de Roeck, Giuseppe Di Sciascio, Miriam Diamond, Marco Drewes, Sarah C. Eno, Rouven Essig, Jared Evans, Erez Etzion, Arturo Fernández Téllez, Oliver Fischer, Jim Freeman, Stefano Giagu, Brandon Gomes , et al. (38 additional authors not shown)

Abstract: The observation of long-lived particles at the LHC would reveal physics beyond the Standard Model, could account for the many open issues in our understanding of our universe, and conceivably point to a more complete theory of the fundamental interactions. Such long-lived particle signatures are fundamentally motivated and can appear in virtually every theoretical construct that address the Hierar… ▽ More The observation of long-lived particles at the LHC would reveal physics beyond the Standard Model, could account for the many open issues in our understanding of our universe, and conceivably point to a more complete theory of the fundamental interactions. Such long-lived particle signatures are fundamentally motivated and can appear in virtually every theoretical construct that address the Hierarchy Problem, Dark Matter, Neutrino Masses and the Baryon Asymmetry of the Universe. We describe in this document a large detector, MATHUSLA, located on the surface above an HL-LHC $pp$ interaction point, that could observe long-lived particles with lifetimes up to the Big Bang Nucleosynthesis limit of 0.1 s. We also note that its large detector area allows MATHUSLA to make important contributions to cosmic ray physics. Because of the potential for making a major breakthrough in our conceptual understanding of the universe, long-lived particle searches should have the highest level of priority. △ Less

Submitted 13 January, 2019; originally announced January 2019.

Comments: 8 pages, 5 figures. Input to the update process of the European Strategy for Particle Physics by the MATHUSLA collaboration (http://mathusla.web.cern.ch). See also CERN-PBC-REPORT-2018-007 for the ESPP contribution of the Physics Beyond Colliders working group, which contains a discussion of low-energy simplified models as well as some comments on MATHUSLA's budget and timelines

A Letter of Intent for MATHUSLA: a dedicated displaced vertex detector above ATLAS or CMS

Authors: Cristiano Alpigiani, Austin Ball, Liron Barak, James Beacham, Yan Benhammo, Tingting Cao, Paolo Camarri, Roberto Cardarelli, Mario Rodriguez-Cahuantzi, John Paul Chou, David Curtin, Miriam Diamond, Giuseppe Di Sciascio, Marco Drewes, Sarah C. Eno, Erez Etzion, Rouven Essig, Jared Evans, Oliver Fischer, Stefano Giagu, Brandon Gomes, Andy Haas, Yuekun Heng, Giuseppe Iaselli, Ken Johns , et al. (39 additional authors not shown)

Abstract: In this Letter of Intent (LOI) we propose the construction of MATHUSLA (MAssive Timing Hodoscope for Ultra-Stable neutraL pArticles), a dedicated large-volume displaced vertex detector for the HL-LHC on the surface above ATLAS or CMS. Such a detector, which can be built using existing technologies with a reasonable budget in time for the HL-LHC upgrade, could search for neutral long-lived particle… ▽ More In this Letter of Intent (LOI) we propose the construction of MATHUSLA (MAssive Timing Hodoscope for Ultra-Stable neutraL pArticles), a dedicated large-volume displaced vertex detector for the HL-LHC on the surface above ATLAS or CMS. Such a detector, which can be built using existing technologies with a reasonable budget in time for the HL-LHC upgrade, could search for neutral long-lived particles (LLPs) with up to several orders of magnitude better sensitivity than ATLAS or CMS, while also acting as a cutting-edge cosmic ray telescope at CERN to explore many open questions in cosmic ray and astro-particle physics. We review the physics motivations for MATHUSLA and summarize its LLP reach for several different possible detector geometries, as well as outline the cosmic ray physics program. We present several updated background studies for MATHUSLA, which help inform a first detector-design concept utilizing modular construction with Resistive Plate Chambers (RPCs) as the primary tracking technology. We present first efficiency and reconstruction studies to verify the viability of this design concept, and we explore some aspects of its total cost. We end with a summary of recent progress made on the MATHUSLA test stand, a small-scale demonstrator experiment currently taking data at CERN Point 1, and finish with a short comment on future work. △ Less

Submitted 2 November, 2018; originally announced November 2018.

Report number: CERN-LHCC-2018-025, LHCC-I-031

Observation of the rare $B^0_s\toμ^+μ^-$ decay from the combined analysis of CMS and LHCb data

Authors: The CMS, LHCb Collaborations, :, V. Khachatryan, A. M. Sirunyan, A. Tumasyan, W. Adam, T. Bergauer, M. Dragicevic, J. Erö, M. Friedl, R. Frühwirth, V. M. Ghete, C. Hartl, N. Hörmann, J. Hrubec, M. Jeitler, W. Kiesenhofer, V. Knünz, M. Krammer, I. Krätschmer, D. Liko, I. Mikulec, D. Rabady, B. Rahbaran , et al. (2807 additional authors not shown)

Abstract: A joint measurement is presented of the branching fractions $B^0_s\toμ^+μ^-$ and $B^0\toμ^+μ^-$ in proton-proton collisions at the LHC by the CMS and LHCb experiments. The data samples were collected in 2011 at a centre-of-mass energy of 7 TeV, and in 2012 at 8 TeV. The combined analysis produces the first observation of the $B^0_s\toμ^+μ^-$ decay, with a statistical significance exceeding six sta… ▽ More A joint measurement is presented of the branching fractions $B^0_s\toμ^+μ^-$ and $B^0\toμ^+μ^-$ in proton-proton collisions at the LHC by the CMS and LHCb experiments. The data samples were collected in 2011 at a centre-of-mass energy of 7 TeV, and in 2012 at 8 TeV. The combined analysis produces the first observation of the $B^0_s\toμ^+μ^-$ decay, with a statistical significance exceeding six standard deviations, and the best measurement of its branching fraction so far. Furthermore, evidence for the $B^0\toμ^+μ^-$ decay is obtained with a statistical significance of three standard deviations. The branching fraction measurements are statistically compatible with SM predictions and impose stringent constraints on several theories beyond the SM. △ Less

Submitted 17 August, 2015; v1 submitted 17 November, 2014; originally announced November 2014.

Comments: Correspondence should be addressed to [email protected]

Report number: CERN-PH-EP-2014-220, CMS-BPH-13-007, LHCb-PAPER-2014-049

Journal ref: Nature 522, 68-72 (04 June 2015)