-
Variational Autoencoders for Noise Reduction in Industrial LLRF Systems
Authors:
J. P. Edelen,
M. J. Henderson,
J. Einstein-Curtis,
C. C. Hall,
J. A. Diaz Cruz,
A. L. Edelen
Abstract:
Industrial particle accelerators inherently operate in much dirtier environments than typical research accelerators. This leads to an increase in noise both in the RF system and in other electronic systems. Combined with the fact that industrial accelerators are mass produced, there is less attention given to optimizing the performance of an individual system. As a result, industrial systems tend…
▽ More
Industrial particle accelerators inherently operate in much dirtier environments than typical research accelerators. This leads to an increase in noise both in the RF system and in other electronic systems. Combined with the fact that industrial accelerators are mass produced, there is less attention given to optimizing the performance of an individual system. As a result, industrial systems tend to under perform considering their hardware hardware capabilities. With the growing demand for accelerators for medical sterilization, food irradiation, cancer treatment, and imaging, improving the signal processing of these machines will increase the margin for the deployment of these systems. Our work is focusing on using machine learning techniques to reduce the noise of RF signals used for pulse-to-pulse feedback in industrial accelerators. We will review our algorithms, simulation results, and results working with measured data. We will then discuss next steps for deployment and testing on an industrial system.
△ Less
Submitted 7 November, 2023; v1 submitted 29 October, 2023;
originally announced November 2023.
-
Anomaly Detection in Particle Accelerators using Autoencoders
Authors:
Jonathan P. Edelen,
Nathan M. Cook
Abstract:
The application of machine learning techniques for anomaly detection in particle accelerators has gained popularity in recent years. These efforts have ranged from the analysis of quenches in radio frequency cavities and superconducting magnets to anomalous beam position monitors, and even losses in rings. Using machine learning for anomaly detection can be challenging owing to the inherent imbala…
▽ More
The application of machine learning techniques for anomaly detection in particle accelerators has gained popularity in recent years. These efforts have ranged from the analysis of quenches in radio frequency cavities and superconducting magnets to anomalous beam position monitors, and even losses in rings. Using machine learning for anomaly detection can be challenging owing to the inherent imbalance in the amount of data collected during normal operations as compared to during faults. Additionally, the data are not always labeled and therefore supervised learning is not possible. Autoencoders, neural networks that form a compressed representation and reconstruction of the input data, are a useful tool for such situations. Here we explore the use of autoencoder reconstruction analysis for the prediction of magnet faults in the Advanced Photon Source (APS) storage ring at Argonne National Laboratory.
△ Less
Submitted 14 December, 2021;
originally announced December 2021.
-
A Vlasov Algorithm Derived from Phase Space Conservation
Authors:
Jonathan P. Edelen,
Stephen D. Webb
Abstract:
Existing approaches to solving the Vlasov equation treat the system as a partial differential equation on a phase space grid, and track in either an Eulerian, Lagrangian, or semi-Lagrangian picture. We present an alternative approach, which treats the Vlasov equation as a conservative flow on phase space, and derives its equations of motion using particle-pushing algorithms akin to particle-in-cel…
▽ More
Existing approaches to solving the Vlasov equation treat the system as a partial differential equation on a phase space grid, and track in either an Eulerian, Lagrangian, or semi-Lagrangian picture. We present an alternative approach, which treats the Vlasov equation as a conservative flow on phase space, and derives its equations of motion using particle-pushing algorithms akin to particle-in-cell methods. Deposition to the grid is determined from the convolution of local basis functions. This approach has the benefit of allowing flexible definitions in the grid, which are decoupled from how the phase space flow evolves. We present numerical examples and comment on the various properties of the algorithm.
△ Less
Submitted 23 July, 2020;
originally announced July 2020.
-
PIP-II Injector Test Warm Front End: Commissioning Update
Authors:
L. Prost,
R. Andrews,
C. Baffes,
J. -P. Carneiro,
B. Chase,
A. Chen,
E. Cullerton,
P. F. Derwent,
J. P. Edelen,
J. Einstein-Curtis,
D. Frolov,
B. Hanna,
D. Peterson,
G. Saewert,
A. Saini,
V. Scarpine,
A. Shemyakin,
J. Steimel,
D. Sun,
A. Warner,
C. Richard,
V. L. S. Sista
Abstract:
The Warm Front End (WFE) of the Proton Improvement Plan II Injector Test at Fermilab has been constructed to its full length. It includes a 15-mA DC, 30-keV H- ion source, a 2 m-long Low Energy Beam Transport (LEBT) with a switching dipole magnet, a 2.1 MeV CW RFQ, followed by a Medium Energy Beam Transport (MEBT) with various diagnostics and a dump. This report presents the commissioning status,…
▽ More
The Warm Front End (WFE) of the Proton Improvement Plan II Injector Test at Fermilab has been constructed to its full length. It includes a 15-mA DC, 30-keV H- ion source, a 2 m-long Low Energy Beam Transport (LEBT) with a switching dipole magnet, a 2.1 MeV CW RFQ, followed by a Medium Energy Beam Transport (MEBT) with various diagnostics and a dump. This report presents the commissioning status, focusing on beam measurements in the MEBT. In particular, a beam with the parameters required for injection into the Booster (5 mA, 0.55 ms macro-pulse at 20 Hz) was transported through the WFE.
△ Less
Submitted 14 June, 2018;
originally announced June 2018.
-
Adaptive beam loading compensation in room temperature bunching cavities
Authors:
J. P. Edelen,
B. E. Chase,
E. Cullerton,
P. Varghese
Abstract:
In this paper we present the design, simulation, and proof of principle results of an optimization based adaptive feed-forward algorithm for beam-loading compensation in a high impedance room temperature cavity. We begin with an overview of prior developments in beam loading compensation. Then we discuss different techniques for adaptive beam loading compensation and why the use of Newton's Method…
▽ More
In this paper we present the design, simulation, and proof of principle results of an optimization based adaptive feed-forward algorithm for beam-loading compensation in a high impedance room temperature cavity. We begin with an overview of prior developments in beam loading compensation. Then we discuss different techniques for adaptive beam loading compensation and why the use of Newton's Method is of interest for this application. This is followed by simulation and initial experimental results of this method.
△ Less
Submitted 23 March, 2018;
originally announced March 2018.
-
Automatic phase calibration for RF cavities using beam-loading signals
Authors:
J. P. Edelen,
B. E. Chase
Abstract:
Precise calibration of the cavity phase signals is necessary for the operation of any particle accelerator. For many systems this requires human in the loop adjustments based on measurements of the beam parameters downstream. Some recent work has developed a scheme for the calibration of the cavity phase using beam measurements and beam-loading however this scheme is still a multi-step process tha…
▽ More
Precise calibration of the cavity phase signals is necessary for the operation of any particle accelerator. For many systems this requires human in the loop adjustments based on measurements of the beam parameters downstream. Some recent work has developed a scheme for the calibration of the cavity phase using beam measurements and beam-loading however this scheme is still a multi-step process that requires heavy automation or human in the loop. In this paper we analyze a new scheme that uses only RF signals reacting to beam-loading to calculate the phase of the beam relative to the cavity. This technique could be used in slow control loops to provide real-time adjustment of the cavity phase calibration without human intervention thereby increasing the stability and reliability of the accelerator.
△ Less
Submitted 23 March, 2018;
originally announced March 2018.
-
Status of the warm front end of PIP-II injector test
Authors:
A. Shemyakin,
M. Alvarez,
R. Andrews,
C. Baffes,
J. -P. Carneiro,
A. Chen,
P. F. Derwent,
J. P. Edelen,
D. Frolov,
B. Hanna,
L. Prost,
A. Saini,
G. Saewert,
V. Scarpine,
V. L. S. Sista,
J. Steimel,
D. Sun,
A. Warner
Abstract:
The Proton Improvement Plan II (PIP-II) at Fermilab is a program of upgrades to the injection complex. At its core is the design and construction of a CW compatible, pulsed H- SRF linac. To validate the concept of the front-end of such machine, a test accelerator known as PIP-II Injector Test (PIP2IT) is under construction. It includes a 10 mA DC, 30 keV H- ion source, a 2 m-long Low Energy Beam T…
▽ More
The Proton Improvement Plan II (PIP-II) at Fermilab is a program of upgrades to the injection complex. At its core is the design and construction of a CW compatible, pulsed H- SRF linac. To validate the concept of the front-end of such machine, a test accelerator known as PIP-II Injector Test (PIP2IT) is under construction. It includes a 10 mA DC, 30 keV H- ion source, a 2 m-long Low Energy Beam Transport (LEBT), a 2.1 MeV CWRFQ, followed by a Medium Energy Beam Transport (MEBT) that feeds the first of 2 cryomodules increasing the beam energy to about 25 MeV, and a High Energy Beam Transport section (HEBT) that takes the beam to a dump. The ion source, LEBT, RFQ, and initial version of the MEBT have been built, installed, and commissioned. This report presents the overall status of the warm front end.
△ Less
Submitted 23 March, 2018;
originally announced March 2018.
-
Low Level RF Control for the PIP-II Accelerator
Authors:
J. P. Edelen,
B. E. Chase,
E. Cullerton,
J. Einstein-Curtis,
J. Holzbauer,
D. Klepec,
Y. Pischalnikov,
W. Schappert,
P. Varghese,
G. Joshi,
S. Khole,
D. Sharma
Abstract:
The PIP-II accelerator is a proposed upgrade to the Fermilab accelerator complex that will replace the existing, 400 MeV room temperature LINAC with an 800 MeV superconducting LINAC. Part of this upgrade includes a new injection scheme into the booster that levies tight requirements on the LLRF control system for the cavities. In this paper we discuss the challenges of the PIP-II accelerator and t…
▽ More
The PIP-II accelerator is a proposed upgrade to the Fermilab accelerator complex that will replace the existing, 400 MeV room temperature LINAC with an 800 MeV superconducting LINAC. Part of this upgrade includes a new injection scheme into the booster that levies tight requirements on the LLRF control system for the cavities. In this paper we discuss the challenges of the PIP-II accelerator and the present status of the LLRF system for this project.
△ Less
Submitted 21 March, 2018;
originally announced March 2018.
-
Current transmission and nonlinear effects in un-gated thermionic cathode RF guns
Authors:
J. P. Edelen,
J. R. Harris
Abstract:
Un-gated thermionic cathode RF guns are well known as a robust source of electrons for many accelerator applications. These sources are in principle scalable to high currents without degradation of the transverse emittance due to control grids but they are also known for being limited by back-bombardment. While back-bombardment presents a significant limitation, there is still a lack of general un…
▽ More
Un-gated thermionic cathode RF guns are well known as a robust source of electrons for many accelerator applications. These sources are in principle scalable to high currents without degradation of the transverse emittance due to control grids but they are also known for being limited by back-bombardment. While back-bombardment presents a significant limitation, there is still a lack of general understanding on how emission over the whole RF period will affect the nature of the beams produced from these guns. In order to improve our understanding of how these guns can be used in general we develop analytical models that predict the transmission efficiency as a function of the design parameters, study how bunch compression and emission enhancement caused by Schottky barrier lowering affect the output current profile in the gun, and study the onset of space-charge limited effects and the resultant virtual cathode formation leading to a modulation in the output current distribution.
△ Less
Submitted 3 May, 2017;
originally announced May 2017.
-
Observation Of Repetition-Rate Dependent Emission From an Un-Gated Thermionic Cathode RF Gun
Authors:
J. P. Edelen,
Y. Sun,
J. R. Harris,
J. W. Lewellen
Abstract:
Recent work at Fermilab in collaboration with the Advanced Photon Source and members of other national labs, designed an experiment to study the relationship between the RF repetition rate and the average current per RF pulse. While existing models anticipate a direct relationship between these two parameters we observed an inverse relationship. We believe this is a result of damage to the barium…
▽ More
Recent work at Fermilab in collaboration with the Advanced Photon Source and members of other national labs, designed an experiment to study the relationship between the RF repetition rate and the average current per RF pulse. While existing models anticipate a direct relationship between these two parameters we observed an inverse relationship. We believe this is a result of damage to the barium coating on the cathode surface caused by a change in back-bombardment power that is unaccounted for in the existing theories. These observations shed new light on the challenges and fundamental limitations associated with scaling an un-gated thermionic cathode RF gun to high average current machines.
△ Less
Submitted 24 February, 2017;
originally announced February 2017.
-
Neural Network Model Of The PXIE RFQ Cooling System and Resonant Frequency Response
Authors:
A. L. Edelen,
S. G. Biedron,
S. V. Milton,
D. Bowring,
B. E. Chase,
J. P. Edelen,
J. Steimel
Abstract:
As part of the PIP-II Injector Experiment (PXIE) accelerator, a four-vane radio frequency quadrupole (RFQ) accelerates a 30-keV, 1-mA to 10-mA H- ion beam to 2.1 MeV. It is designed to operate at a frequency of 162.5 MHz with arbitrary duty factor, including continuous wave (CW) mode. The resonant frequency is controlled solely by a water-cooling system. We present an initial neural network model…
▽ More
As part of the PIP-II Injector Experiment (PXIE) accelerator, a four-vane radio frequency quadrupole (RFQ) accelerates a 30-keV, 1-mA to 10-mA H- ion beam to 2.1 MeV. It is designed to operate at a frequency of 162.5 MHz with arbitrary duty factor, including continuous wave (CW) mode. The resonant frequency is controlled solely by a water-cooling system. We present an initial neural network model of the RFQ frequency response to changes in the cooling system and RF power conditions during pulsed operation. A neural network model will be used in a model predictive control scheme to regulate the resonant frequency of the RFQ.
△ Less
Submitted 21 December, 2016;
originally announced December 2016.
-
First Steps Toward Incorporating Image Based Diagnostics Into Particle Accelerator Control Systems Using Convolutional Neural Networks
Authors:
A. L. Edelen,
S. G. Biedron,
S. V. Milton,
J. P. Edelen
Abstract:
At present, a variety of image-based diagnostics are used in particle accelerator systems. Often times, these are viewed by a human operator who then makes appropriate adjustments to the machine. Given recent advances in using convolutional neural networks (CNNs) for image processing, it should be possible to use image diagnostics directly in control routines (NN-based or otherwise). This is espec…
▽ More
At present, a variety of image-based diagnostics are used in particle accelerator systems. Often times, these are viewed by a human operator who then makes appropriate adjustments to the machine. Given recent advances in using convolutional neural networks (CNNs) for image processing, it should be possible to use image diagnostics directly in control routines (NN-based or otherwise). This is especially appealing for non-intercepting diagnostics that could run continuously during beam operation. Here, we show results of a first step toward implementing such a controller: our trained CNN can predict multiple simulated downstream beam parameters at the Fermilab Accelerator Science and Technology (FAST) facility's low energy beamline using simulated virtual cathode laser images, gun phases, and solenoid strengths.
△ Less
Submitted 16 December, 2016;
originally announced December 2016.
-
Resonant Frequency Control For the PIP-II Injector Test RFQ: Control Framework and Initial Results
Authors:
A. L. Edelen,
S. G. Biedron,
S. V. Milton,
D. Bowring,
B. E. Chase,
J. P. Edelen,
D. Nicklaus,
J. Steimel
Abstract:
For the PIP-II Injector Test (PI-Test) at Fermilab, a four-vane radio frequency quadrupole (RFQ) is designed to accelerate a 30-keV, 1-mA to 10-mA, H- beam to 2.1 MeV under both pulsed and continuous wave (CW) RF operation. The available headroom of the RF amplifiers limits the maximum allowable detuning to 3 kHz, and the detuning is controlled entirely via thermal regulation. Fine control over th…
▽ More
For the PIP-II Injector Test (PI-Test) at Fermilab, a four-vane radio frequency quadrupole (RFQ) is designed to accelerate a 30-keV, 1-mA to 10-mA, H- beam to 2.1 MeV under both pulsed and continuous wave (CW) RF operation. The available headroom of the RF amplifiers limits the maximum allowable detuning to 3 kHz, and the detuning is controlled entirely via thermal regulation. Fine control over the detuning, minimal manual intervention, and fast trip recovery is desired. In addition, having active control over both the walls and vanes provides a wider tuning range. For this, we intend to use model predictive control (MPC). To facilitate these objectives, we developed a dedicated control framework that handles higher-level system decisions as well as executes control calculations. It is written in Python in a modular fashion for easy adjustments, readability, and portability. Here we describe the framework and present the first control results for the PI-Test RFQ under pulsed and CW operation.
△ Less
Submitted 16 December, 2016;
originally announced December 2016.
