-
Electron Cloud Measurements in Fermilab Booster
Authors:
S. A. K. Wijethunga,
N. Eddy,
J. Eldred,
C. Y. Tan,
B. Fellenz,
E. Pozdeyev,
R. V. Sharankova
Abstract:
Fermilab Booster synchrotron requires an intensity upgrade from 4.5x1012 to 6.5x1012 protons per pulse as a part of Fermilab's Proton Improvement Plan-II (PIP-II). One of the factors which may limit the high-intensity performance is the fast transverse instabilities caused by electron cloud effects. According to the experience in the Recycler, the electron cloud gradually builds up over multiple t…
▽ More
Fermilab Booster synchrotron requires an intensity upgrade from 4.5x1012 to 6.5x1012 protons per pulse as a part of Fermilab's Proton Improvement Plan-II (PIP-II). One of the factors which may limit the high-intensity performance is the fast transverse instabilities caused by electron cloud effects. According to the experience in the Recycler, the electron cloud gradually builds up over multiple turns inside the combined function magnets and can reach final intensities orders of magnitude greater than in a pure dipole. Since the Booster synchrotron also incorporates combined function magnets, it is important to measure the presence of electron cloud. The presence or apparent absence of the electron cloud was investigated using two different methods: measuring bunch-by-bunch tune shift by changing the bunch train structure at different intensities and propagating a microwave carrier signal through the beampipe and analyzing the phase modulation of the signal. This paper presents the results of the two methods and corresponding simulation results conducted using PyECLOUD software.
△ Less
Submitted 19 July, 2023;
originally announced July 2023.
-
A Modern Ethernet Data Acquisition Architecture for Fermilab Beam Instrumentation
Authors:
R. Santucci,
J. Diamond,
N. Eddy,
A. Semenov,
D. Voy
Abstract:
The Fermilab Accelerator Division, Instrumentation Department is adopting an open-source framework to replace our embedded VME-based data acquisition systems. Utilizing an iterative methodology, we first moved to embedded Linux, removing the need for VxWorks. Next, we adopted Ethernet on each data acquisition module eliminating the need for the VME backplane in addition to communicating with a rac…
▽ More
The Fermilab Accelerator Division, Instrumentation Department is adopting an open-source framework to replace our embedded VME-based data acquisition systems. Utilizing an iterative methodology, we first moved to embedded Linux, removing the need for VxWorks. Next, we adopted Ethernet on each data acquisition module eliminating the need for the VME backplane in addition to communicating with a rack mount server. Development of DDCP (Distributed Data Communications Protocol), allowed for an abstraction between the firmware and software layers. Each data acquisition module was adapted to read out using 1 GbE and aggregated at a switch which up linked to a 10 GbE network. Current development includes scaling the system to aggregate more modules, to increase bandwidth to support multiple systems and to adopt MicroTCA as a crate technology. The architecture was utilized on various beamlines around the Fermilab complex including PIP2IT, FAST/IOTA and the Muon Delivery Ring. In summary, we were able to develop a data acquisition framework which incrementally replaces VxWorks & VME hardware as well as increases our total bandwidth to 10 Gbit/s using off the shelf Ethernet technology.
△ Less
Submitted 19 September, 2022;
originally announced September 2022.
-
Coupled Bunch Instabilities Growth in the Fermilab Booster during Acceleration Cycle
Authors:
C. M. Bhat,
N. Eddy
Abstract:
Currently, Fermilab Booster accelerates ~4.5E12 protons per pulse (ppp) in 81 bunches from 400 MeV to 8 GeV at 15 Hz to provide beam to multiple HEP experiments and is being upgraded to handle higher beam intensity >6.7E12 ppp at a repetition rate of 20 Hz. In the current mode of operation, we control longitudinal coupled bunch instabilities (LCBI) using combination of passive and active dampers.…
▽ More
Currently, Fermilab Booster accelerates ~4.5E12 protons per pulse (ppp) in 81 bunches from 400 MeV to 8 GeV at 15 Hz to provide beam to multiple HEP experiments and is being upgraded to handle higher beam intensity >6.7E12 ppp at a repetition rate of 20 Hz. In the current mode of operation, we control longitudinal coupled bunch instabilities (LCBI) using combination of passive and active dampers. The issues with LCBI are expected to worsen at higher beam intensities. Here, we would like to investigate at what time in the beam cycle a particular mode is going to originate and how much it contributes at a different time of the acceleration cycle using the collected wall current monitor data from injection to extraction. Also, measure growth rates as a function of beam intensity for some dominant modes. Finally, this paper presents results from the observed LCBI analysis for the highest available beam intensities, unexpected findings, and future plans to mitigate the LCBI at higher beam intensities
△ Less
Submitted 18 October, 2021;
originally announced October 2021.
-
Commissioning and Operation of FAST Electron Linac at Fermilab
Authors:
A. Romanov,
C. Baffes,
D. R. Broemmelsiek,
K. Carlson,
D. J. Crawford,
N. Eddy,
D. Edstrom Jr.,
E. R. Harms,
J. Hurd,
M. Kucera,
J. Leibfritz,
I. Rakhno,
J. Reid,
J. Ruan,
J. Santucci,
V. Shiltsev,
G. Stancari,
R. Thurman-Keup,
A. Valishev,
A. Warner
Abstract:
We report results of the beam commissioning and first operation of the 1.3 GHz superconducting RF electron linear accelerator at Fermilab Accelerator Science and Technology (FAST) facility. Construction of the linac was completed and the machine was commissioned with beam in 2017. The maximum total beam energy of about 300 MeV was achieved with the record energy gain of 250 MeV in the ILC-type SRF…
▽ More
We report results of the beam commissioning and first operation of the 1.3 GHz superconducting RF electron linear accelerator at Fermilab Accelerator Science and Technology (FAST) facility. Construction of the linac was completed and the machine was commissioned with beam in 2017. The maximum total beam energy of about 300 MeV was achieved with the record energy gain of 250 MeV in the ILC-type SRF cryomodule. The photoinjector was tuned to produce trains of 200 pC bunches with a frequency of 3 MHz at a repetition rate of 1 Hz. This report describes the aspects of machine commissioning such as tuning of the SRF cryomodule and beam optics optimization. We also present highlights of an experimental program carried out parasitically during the two-month run, including studies of wake-fields, and advanced beam phase space manipulation.
△ Less
Submitted 9 November, 2018;
originally announced November 2018.
-
Submacropulse Electron-Beam Dynamics Correlated With Higher-Order Modes In Tesla-Type Superconducting RF Cavities
Authors:
A. H. Lumpkin,
R. Thurman-Keup,
D. Edstrom,
J. Ruan,
N. Eddy,
P. Prieto,
O. Napoly,
B. E. Carlsten,
K. Bishofberger
Abstract:
We report the direct observations of sub-macropulse beam centroid oscillations correlated with higher order modes (HOMs) which were generated by off-axis electron beam steering in TESLA-type superconducting RF cavities. The experiments were performed at the Fermilab Accelerator Science and Technology (FAST) facility using its unique configuration of a photocathode rf gun injecting beam into two se…
▽ More
We report the direct observations of sub-macropulse beam centroid oscillations correlated with higher order modes (HOMs) which were generated by off-axis electron beam steering in TESLA-type superconducting RF cavities. The experiments were performed at the Fermilab Accelerator Science and Technology (FAST) facility using its unique configuration of a photocathode rf gun injecting beam into two separated 9-cell cavities in series with corrector magnets and beam position monitors (BPMs) located before, between, and after them. Oscillations of ~100 kHz in the vertical plane and ~380 kHz in the horizontal plane with up to 600-μm amplitudes were observed in a 3-MHz micropulse repetition rate beam with charges of 100, 300, 500, and 1000 pC/b. However, the effects were much reduced at 100 pC/b. The measurements were based on HOM detector circuitry targeting the first and second dipole passbands, rf BPM bunch-by-bunch array data, imaging cameras, and a framing camera. Calculations reproduced the oscillation frequencies of the phenomena in the vertical case. In principle, these fundamental results may be scaled to cryomodule configurations of major accelerator facilities.
△ Less
Submitted 11 July, 2018;
originally announced July 2018.
-
Diagnostics upgrades for investigations of HOM effects in Tesla-type SCRF cavities
Authors:
A. H. Lumpkin,
D. Edstrom Jr.,
J. Ruan,
R. Thurman-Keup,
Y. Shin,
P. Prieto,
N. Eddy,
B. E. Carlsten
Abstract:
We describe the upgrades to diagnostic capabilities on the Fermilab Accelerator Science and Technology (FAST) electron linear accelerator that will allow investigations of the effects of high-order modes (HOMs) in SCRF cavities on macropulse-average beam quality. We examine the dipole modes in the first pass-band generally observed in the 1.6-1.9 GHz regime for TESLA-type SCRF cavities due to unif…
▽ More
We describe the upgrades to diagnostic capabilities on the Fermilab Accelerator Science and Technology (FAST) electron linear accelerator that will allow investigations of the effects of high-order modes (HOMs) in SCRF cavities on macropulse-average beam quality. We examine the dipole modes in the first pass-band generally observed in the 1.6-1.9 GHz regime for TESLA-type SCRF cavities due to uniform transverse beam offsets of the electron beam. Such cavities are the basis of the accelerators such as the European XFEL and the proposed MaRIE XFEL facility. Preliminary HOM detector data, prototype BPM test data, and first framing camera OTR data with ~20 micron spatial resolution at 250 pC per bunch will be presented.
△ Less
Submitted 2 March, 2018;
originally announced March 2018.
-
Design Of The LBNF Beamline
Authors:
V. Papadimitriou,
K. Ammigan,
J. Anderson Jr.,
K. E. Anderson,
R. Andrews,
V. Bocean,
C. F. Crowley,
N. Eddy,
B. D. Hartsell,
S. Hays,
P. Hurh,
J. Hylen,
J. A. Johnstone,
P. Kasper,
T. Kobilarcik,
G. E. Krafczyk,
B. Lundberg,
A. Marchionni,
N. V. Mokhov,
C. D. Moore,
D. Pushka,
I. Rakhno,
S. D. Reitzner,
P. Schlabach,
V. Sidorov
, et al. (9 additional authors not shown)
Abstract:
The Long Baseline Neutrino Facility (LBNF) will utilize a beamline located at Fermilab to provide and aim a neutrino beam of sufficient intensity and appropriate energy range toward the Deep Underground Neutrino Experiment (DUNE) detectors, placed deep underground at the SURF Facility in Lead, South Dakota. The primary proton beam (60-120 GeV) will be extracted from the MI-10 section of Fermilab's…
▽ More
The Long Baseline Neutrino Facility (LBNF) will utilize a beamline located at Fermilab to provide and aim a neutrino beam of sufficient intensity and appropriate energy range toward the Deep Underground Neutrino Experiment (DUNE) detectors, placed deep underground at the SURF Facility in Lead, South Dakota. The primary proton beam (60-120 GeV) will be extracted from the MI-10 section of Fermilab's Main Injector. Neutrinos will be produced when the protons interact with a solid target to produce mesons which will be subsequently focused by magnetic horns into a 194m long decay pipe where they decay into muons and neutrinos. The parameters of the facility were determined taking into account the physics goals, spatial and radiological constraints, and the experience gained by operating the NuMI facility at Fermilab. The Beamline facility is designed for initial operation at a proton-beam power of 1.2 MW, with the capability to support an upgrade to 2.4 MW. LBNF/DUNE obtained CD-1 approval in November 2015. We discuss here the design status and the associated challenges as well as the R&D and plans for improvements before baselining the facility.
△ Less
Submitted 14 April, 2017;
originally announced April 2017.
-
Analysis and Measurement of the Transfer Matrix of a 9-cell 1.3-GHz Superconducting Cavity
Authors:
A. Halavanau,
N. Eddy,
D. Edstrom,
E. Harms,
A. Lunin,
P. Piot,
A. Romanov,
J. Ruan,
N. Solyak,
V. Shiltsev
Abstract:
Superconducting linacs are capable of producing intense, stable, high-quality electron beams that have found widespread applications in science and industry. The 9-cell 1.3-GHz superconducting standing-wave accelerating RF cavity originally developed for $e^+/e^-$ linear-collider applications [B. Aunes, {\em et al.} Phys. Rev. ST Accel. Beams {\bf 3}, 092001 (2000)] has been broadly employed in va…
▽ More
Superconducting linacs are capable of producing intense, stable, high-quality electron beams that have found widespread applications in science and industry. The 9-cell 1.3-GHz superconducting standing-wave accelerating RF cavity originally developed for $e^+/e^-$ linear-collider applications [B. Aunes, {\em et al.} Phys. Rev. ST Accel. Beams {\bf 3}, 092001 (2000)] has been broadly employed in various superconducting-linac designs. In this paper we discuss the transfer matrix of such a cavity and present its measurement performed at the Fermilab Accelerator Science and Technology (FAST) facility. The experimental results are found to be in agreement with analytical calculations and numerical simulations.
△ Less
Submitted 22 April, 2017; v1 submitted 27 January, 2017;
originally announced January 2017.
-
Initial experimental results of a machine learning-based temperature control system for an RF gun
Authors:
A. L. Edelen,
S. G. Biedron,
S. V. Milton,
B. E. Chase,
D. J. Crawford,
N. Eddy,
D. Edstrom Jr.,
E. R. Harms,
J. Ruan,
J. K. Santucci,
P. Stabile
Abstract:
Colorado State University (CSU) and Fermi National Accelerator Laboratory (Fermilab) have been develo** a control system to regulate the resonant frequency of an RF electron gun. As part of this effort, we present initial test results for a benchmark temperature controller that combines a machine learning-based model and a predictive control algorithm. This is part of an on-going effort to devel…
▽ More
Colorado State University (CSU) and Fermi National Accelerator Laboratory (Fermilab) have been develo** a control system to regulate the resonant frequency of an RF electron gun. As part of this effort, we present initial test results for a benchmark temperature controller that combines a machine learning-based model and a predictive control algorithm. This is part of an on-going effort to develop adaptive, machine learning-based tools specifically to address control challenges found in particle accelerator systems.
△ Less
Submitted 5 November, 2015;
originally announced November 2015.
-
Mu2e Technical Design Report
Authors:
L. Bartoszek,
E. Barnes,
J. P. Miller,
J. Mott,
A. Palladino,
J. Quirk,
B. L. Roberts,
J. Crnkovic,
V. Polychronakos,
V. Tishchenko,
P. Yamin,
C. -h. Cheng,
B. Echenard,
K. Flood,
D. G. Hitlin,
J. H. Kim,
T. S. Miyashita,
F. C. Porter,
M. Röhrken,
J. Trevor,
R. -Y. Zhu,
E. Heckmaier,
T. I. Kang,
G. Lim,
W. Molzon
, et al. (238 additional authors not shown)
Abstract:
The Mu2e experiment at Fermilab will search for charged lepton flavor violation via the coherent conversion process mu- N --> e- N with a sensitivity approximately four orders of magnitude better than the current world's best limits for this process. The experiment's sensitivity offers discovery potential over a wide array of new physics models and probes mass scales well beyond the reach of the L…
▽ More
The Mu2e experiment at Fermilab will search for charged lepton flavor violation via the coherent conversion process mu- N --> e- N with a sensitivity approximately four orders of magnitude better than the current world's best limits for this process. The experiment's sensitivity offers discovery potential over a wide array of new physics models and probes mass scales well beyond the reach of the LHC. We describe herein the preliminary design of the proposed Mu2e experiment. This document was created in partial fulfillment of the requirements necessary to obtain DOE CD-2 approval.
△ Less
Submitted 16 March, 2015; v1 submitted 21 January, 2015;
originally announced January 2015.
-
Instrumentation Developments and Beam Studies for the Fermilab Proton Improvement Plan LINAC Upgrade and New RFQ Front-End
Authors:
Victor E. Scarpine,
Cheng-Yang Tan,
Pat R. Karns,
Daniel S. Bollinger,
Kevin L. Duel,
Nathan Eddy,
Ning Lui,
Alexei Semenov,
Raymond E. Tomlin,
William A. Pellico
Abstract:
Fermilab is develo** a Proton Improvement Plan (PIP) to increase throughput of its proton source. The plan addresses hardware modifications to increase repetition rate and improve beam loss while ensuring viable operation of the proton source through 2025. The first phase of the PIP will enable the Fermilab proton source to deliver 1.8e17 protons per hour by mid-2013. As part of this initial upg…
▽ More
Fermilab is develo** a Proton Improvement Plan (PIP) to increase throughput of its proton source. The plan addresses hardware modifications to increase repetition rate and improve beam loss while ensuring viable operation of the proton source through 2025. The first phase of the PIP will enable the Fermilab proton source to deliver 1.8e17 protons per hour by mid-2013. As part of this initial upgrade, Fermilab plans to install a new front-end consisting of dual H- ion sources and a 201 MHz pulsed RFQ. This paper will present beam studies measurements of this new front-end and discuss new beam instrumentation upgrades for the Fermilab linac.
△ Less
Submitted 29 August, 2014;
originally announced August 2014.
-
Observation of Instabilities of Coherent Transverse Ocillations in the Fermilab Booster
Authors:
Y. Alexahin,
N. Eddy,
E. Gianfelice-Wendt,
V. Lebedev,
W. Marsh,
W. Pellico,
K. Triplett
Abstract:
The Fermilab Booster - built more than 40 years ago - operates well above the design proton beam intensity of 4x10**12 ppp. Still, the Fermilab neutrino experiments call for even higher intensity of 5.5x10**12 ppp. A multitude of intensity related effects must be overcome in order to meet this goal including suppression of coherent dipole instabilities of transverse oscillations which manifest the…
▽ More
The Fermilab Booster - built more than 40 years ago - operates well above the design proton beam intensity of 4x10**12 ppp. Still, the Fermilab neutrino experiments call for even higher intensity of 5.5x10**12 ppp. A multitude of intensity related effects must be overcome in order to meet this goal including suppression of coherent dipole instabilities of transverse oscillations which manifest themselves as a sudden drop in the beam current. In this report we present the results of observation of these instabilities at different tune, coupling and chromaticity settings and discuss possible cures.
△ Less
Submitted 31 January, 2013;
originally announced January 2013.
-
HOM Choice Study with Test Electronics for use as Beam Position Diagnostics in 3.9 GHz Accelerating Cavities in FLASH
Authors:
Nicoleta Baboi,
Bastian Lorbeer,
Pei Zhang,
Nathan Eddy,
Brian Fellenz,
Manfred Wendt
Abstract:
Higher Order Modes (HOM) excited by the beam in the 3.9 GHz accelerating cavities in FLASH can be used for beam position diagnostics, as in a cavity beam position monitor. Previous studies of the modal choices within the complicated spectrum have revealed several options: cavity modes with strong coupling to the beam, and therefore with the potential for better position resolution, but which are p…
▽ More
Higher Order Modes (HOM) excited by the beam in the 3.9 GHz accelerating cavities in FLASH can be used for beam position diagnostics, as in a cavity beam position monitor. Previous studies of the modal choices within the complicated spectrum have revealed several options: cavity modes with strong coupling to the beam, and therefore with the potential for better position resolution, but which are propagating within all 4 cavities, and modes localized in the cavities or the beam pipes, which can give localized position information, but which provide worse resolution. For a better characterization of these options, a set of test electronics has been built, which can down-convert various frequencies between about 4 and 9 GHz to 70 MHz. The performance of various 20 MHz bands has been estimated. The best resolution of 20 μm was found for some propagating modes. Based on this study one band at ca. 5 GHz was chosen for high resolution position monitoring and a band at ca. 9 GHz for localized monitoring.
△ Less
Submitted 14 October, 2012;
originally announced October 2012.
-
A Wire Position Monitor System for the 1.3 GHZ Tesla-Style Cryomodule at the Fermilab New-Muon-Lab Accelerator
Authors:
N. Eddy,
B. Fellenz,
P. Prieto,
A. Semenov,
D. C. Voy,
M. Wendt
Abstract:
The first cryomodule for the beam test facility at the Fermilab New-Muon-Lab building is currently under RF commissioning. Among other diagnostics systems, the transverse position of the helium gas return pipe with the connected 1.3 GHz SRF accelerating cavities is measured along the ~15 m long module using a stretched-wire position monitoring system. An overview of the wire position monitor syste…
▽ More
The first cryomodule for the beam test facility at the Fermilab New-Muon-Lab building is currently under RF commissioning. Among other diagnostics systems, the transverse position of the helium gas return pipe with the connected 1.3 GHz SRF accelerating cavities is measured along the ~15 m long module using a stretched-wire position monitoring system. An overview of the wire position monitor system technology is given, along with preliminary results taken at the initial module cool down, and during further testing. As the measurement system offers a high resolution, we also discuss options for use as a vibration detector.
△ Less
Submitted 21 September, 2012;
originally announced September 2012.
-
High Resolution BPM Upgrade for the ATF Dam** Ring at KEK
Authors:
N. Eddy,
C. Briegel,
B. Fellenz,
E. Gianfelice-Wendt,
P. Prieto,
R. Rechenmacher,
A. Semenov,
D. Voy,
M. Wendt,
D. Zhang,
N. Terunuma,
J. Urakawa
Abstract:
A beam position monitor (BPM) upgrade at the KEK Accelerator Test Facility (ATF) dam** ring has been accomplished, carried out by a KEK/FNAL/SLAC collaboration under the umbrella of the global ILC R&D effort. The upgrade consists of a high resolution, high reproducibility read-out system, based on analog and processing, and also implements a new automatic gain error correction schema. The techni…
▽ More
A beam position monitor (BPM) upgrade at the KEK Accelerator Test Facility (ATF) dam** ring has been accomplished, carried out by a KEK/FNAL/SLAC collaboration under the umbrella of the global ILC R&D effort. The upgrade consists of a high resolution, high reproducibility read-out system, based on analog and processing, and also implements a new automatic gain error correction schema. The technical concept and realization as well as results of beam studies are presented.
△ Less
Submitted 20 September, 2012;
originally announced September 2012.
-
Using the transverse digital damper as a real-time tune monitor for the Booster synchrotron at Fermilab
Authors:
N. Eddy,
O. Lysenko
Abstract:
The Fermilab Booster is a fast ram** (15Hz) synchrotron which accelerates protons from 400MeV to 8GeV. During commissioning of a transverse digital damper system, it was shown that the damper could provide a measurement of the machine tune throughout the cycle by exciting just 1 of the 84 bunches with minimal impact on the machine operation. The algorithms used to make the measurement have been…
▽ More
The Fermilab Booster is a fast ram** (15Hz) synchrotron which accelerates protons from 400MeV to 8GeV. During commissioning of a transverse digital damper system, it was shown that the damper could provide a measurement of the machine tune throughout the cycle by exciting just 1 of the 84 bunches with minimal impact on the machine operation. The algorithms used to make the measurement have been incorporated into the damper FPGA firmware allowing for real-time tune monitoring of all Booster cycles.
△ Less
Submitted 19 September, 2012;
originally announced September 2012.
-
A Study of Beam Position Diagnostics with Beam-excited Dipole Higher Order Modes using a Downconverter Test Electronics in Third Harmonic 3.9 GHz Superconducting Accelerating Cavities at FLASH
Authors:
P. Zhang,
N. Baboi,
N. Eddy,
B. Fellenz,
R. M. Jones,
B. Lorbeer,
T. Wamsat,
M. Wendt
Abstract:
Beam-excited higher order modes (HOM) in accelerating cavities contain transverse beam position information. Previous studies have narrowed down three modal options for beam position diagnostics in the third harmonic 3.9 GHz cavities at FLASH. Localized modes in the beam pipes at approximately 4.1 GHz and in the fifth cavity dipole band at approximately 9 GHz were found, that can provide a local m…
▽ More
Beam-excited higher order modes (HOM) in accelerating cavities contain transverse beam position information. Previous studies have narrowed down three modal options for beam position diagnostics in the third harmonic 3.9 GHz cavities at FLASH. Localized modes in the beam pipes at approximately 4.1 GHz and in the fifth cavity dipole band at approximately 9 GHz were found, that can provide a local measurement of the beam position. In contrast, propagating modes in the first and second dipole bands between 4.2 and 5.5 GHz can reach a better resolution. All the options were assessed with a specially designed test electronics built by Fermilab. The aim is to define a mode or spectral region suitable for the HOM electronics. Two data analysis techniques are used and compared in extracting beam position information from the dipole HOMs: direct linear regression and singular value decomposition. Current experiments suggest a resolution of 50 μm accuracy in predicting local beam position using modes in the fifth dipole band, and a global resolution of 20 μm over the complete module. Based on these results we decided to build a HOM electronics for the second dipole band and the fifth dipole band, so that we will have both high resolution measurements for the whole module, and localized measurements for individual cavity. The prototype electronics is being built by Fermilab and planned to be tested in FLASH by the end of 2012.
△ Less
Submitted 10 August, 2012;
originally announced August 2012.
-
Transverse instability of the antiproton beam in the Recycler Ring
Authors:
L. R. Prost,
C. M. Bhat,
A. Burov,
J. Crisp,
N. Eddy,
M. Hu,
A. Shemyakin
Abstract:
The brightness of the antiproton beam in Fermilab's 8 GeV Recycler ring is limited by a transverse instability. This instability has occurred during the extraction process to the Tevatron for large stacks of antiprotons even with dampers in operation. This paper describes observed features of the instability, introduces the threshold phase density to characterize the beam stability, and finds the…
▽ More
The brightness of the antiproton beam in Fermilab's 8 GeV Recycler ring is limited by a transverse instability. This instability has occurred during the extraction process to the Tevatron for large stacks of antiprotons even with dampers in operation. This paper describes observed features of the instability, introduces the threshold phase density to characterize the beam stability, and finds the results to be in agreement with a resistive wall instability model. Effective exclusion of the longitudinal tails from Landau dam** by decreasing the depth of the RF potential well is observed to lower the threshold density by up to a factor of two.
△ Less
Submitted 9 August, 2012;
originally announced August 2012.
-
Higher Order Modes for Beam Diagnostics in Third Harmonic 3.9 GHz Accelerating Module
Authors:
N. Baboi,
N. Eddy,
T. Flisgen,
H. -W. Glock,
R. M. Jones,
I. R. R. Shinton,
P. Zhang
Abstract:
An international team is currently investigating the best way to use Higher Order Modes (HOM) for beam diagnostics in 3.9 GHz cavities. HOMs are excited by charged particles when passing through an accelerating structure. Third harmonic cavities working at 3.9 GHz have been installed in FLASH to linearize the bunch energy profile. A proof-of-principle of using HOMs for beam monitoring has been mad…
▽ More
An international team is currently investigating the best way to use Higher Order Modes (HOM) for beam diagnostics in 3.9 GHz cavities. HOMs are excited by charged particles when passing through an accelerating structure. Third harmonic cavities working at 3.9 GHz have been installed in FLASH to linearize the bunch energy profile. A proof-of-principle of using HOMs for beam monitoring has been made at FLASH in the TESLA 1.3 GHz cavities. Since the wakefields generated in the 3.9 GHz cavities are significantly larger, their impact on the beam should be carefully minimized. Therefore our target is to monitor HOMs and minimize them by aligning the beam on the cavity axis. The difficulty is that, in comparison to the 1.3 GHz cavities, the HOM-spectrum is dense, making it difficult to identify individual modes. Also, most modes propagate through the whole cryo-module containing several cavities, making it difficult to measure local beam properties. In this paper the options for the HOM-based beam position monitors are discussed.
△ Less
Submitted 19 June, 2012;
originally announced June 2012.
-
Transverse Instabilities in the FERMILAB Recycler
Authors:
L. R. Prost,
A. Burov,
A. Shemyakin,
C. M. Bhat,
J. Crisp,
N. Eddy
Abstract:
Transverse instabilities of the antiproton beam have been observed in the Recycler ring soon after its commissioning. After installation of transverse dampers, the threshold for the instability limit increased significantly but the instability is still found to limit the brightness of the antiprotons extracted from the Recycler for Tevatron shots. In this paper, we describe observations of the ins…
▽ More
Transverse instabilities of the antiproton beam have been observed in the Recycler ring soon after its commissioning. After installation of transverse dampers, the threshold for the instability limit increased significantly but the instability is still found to limit the brightness of the antiprotons extracted from the Recycler for Tevatron shots. In this paper, we describe observations of the instabilities during the extraction process as well as during dedicated studies. The measured instability threshold phase density agrees with the prediction of the rigid beam model within a factor of 2. Also, we conclude that the instability threshold can be significantly lowered for a bunch contained in a narrow and shallow potential well due to effective exclusion of the longitudinal tails from Landau dam**.
△ Less
Submitted 19 January, 2012;
originally announced January 2012.
-
Longitudinal bunch monitoring at the Fermilab Tevatron and Main Injector synchrotrons
Authors:
R. Thurman-Keup,
C. Bhat,
W. Blokland,
J. Crisp,
N. Eddy,
B. Fellenz,
R. Flora,
A. Hahn,
S. Hansen,
T. Kiper,
A. Para,
S. Pordes,
A. V. Tollestrup
Abstract:
The measurement of the longitudinal behavior of the accelerated particle beams at Fermilab is crucial to the optimization and control of the beam and the maximizing of the integrated luminosity for the particle physics experiments. Longitudinal measurements in the Tevatron and Main Injector synchrotrons are based on the analysis of signals from resistive wall current monitors. This article describ…
▽ More
The measurement of the longitudinal behavior of the accelerated particle beams at Fermilab is crucial to the optimization and control of the beam and the maximizing of the integrated luminosity for the particle physics experiments. Longitudinal measurements in the Tevatron and Main Injector synchrotrons are based on the analysis of signals from resistive wall current monitors. This article describes the signal processing performed by a 2 GHz-bandwidth oscilloscope together with a computer running a LabVIEW program which calculates the longitudinal beam parameters.
△ Less
Submitted 13 October, 2011;
originally announced October 2011.
-
Higher Order Modes in Third Harmonic Cavities for XFEL/FLASH
Authors:
I. R. R. Shinton,
N. Baboi,
N. Eddy,
T. Flisgen,
H. W. Glock,
R. M. Jones,
N. Juntong,
T. N. Khabiboulline,
U van Rienen,
P. Zhang
Abstract:
We analyse higher order modes in the 3.9 GHz bunch sha** cavities recently installed in the FLASH facility at DESY. We report on recent experimental results on the frequency spectrum from probe based measurements made at CMTB at DESY. These are compared to those predicted by finite difference and finite element computer codes. This study is focused mainly on the dipole component of the multi-pol…
▽ More
We analyse higher order modes in the 3.9 GHz bunch sha** cavities recently installed in the FLASH facility at DESY. We report on recent experimental results on the frequency spectrum from probe based measurements made at CMTB at DESY. These are compared to those predicted by finite difference and finite element computer codes. This study is focused mainly on the dipole component of the multi-pole expansion of the wakefield.. The modes are readily identifiable as single-cavity modes provided the frequencies of these modes are below the cut-off of the inter-connecting beam pipes. The modes above cut-off are coupled to the 4 cavities and are distinct from single cavity modes
△ Less
Submitted 1 June, 2010;
originally announced June 2010.
-
Measurements and Analysis of Beam Transfer Functions in the Fermilab Recycler Ring Using the Transverse Digital Damper System
Authors:
N. Eddy,
J. L. Crisp,
M. Hu
Abstract:
The primary purpose of the Fermilab Recycler Ring Transverse Digital Damper System is to prevent instabilities due to high phase space densities of the cooled antiproton beam. The system was designed to facilitate Beam Transfer Function measurements using a signal analyzer connected to auxiliary system ports for timing and diagnostic purposes. The Digital Damper System has the capability for bot…
▽ More
The primary purpose of the Fermilab Recycler Ring Transverse Digital Damper System is to prevent instabilities due to high phase space densities of the cooled antiproton beam. The system was designed to facilitate Beam Transfer Function measurements using a signal analyzer connected to auxiliary system ports for timing and diagnostic purposes. The Digital Damper System has the capability for both open and closed loop measurements. The Beam Transfer Function provides direct measurement of the machine impedance, and beam and lattice parameters such as betatron tune and chromaticity. An overview of the technique is presented along with analysis and results from open and closed loop measurements in the Fermilab Recycler Ring.
△ Less
Submitted 18 November, 2008;
originally announced November 2008.
-
Track Extrapolation and Distribution for the CDF-II Trigger System
Authors:
Robert Downing,
Nathan Eddy,
Lee Holloway,
Mike Kasten,
Hyunsoo Kim,
James Kraus,
Christopher Marino,
Kevin Pitts,
John Strologas,
Anyes Taffard
Abstract:
The CDF-II experiment is a multipurpose detector designed to study a wide range of processes observed in the high energy proton-antiproton collisions produced by the Fermilab Tevatron. With event rates greater than 1MHz, the CDF-II trigger system is crucial for selecting interesting events for subsequent analysis. This document provides an overview of the Track Extrapolation System (XTRP), a com…
▽ More
The CDF-II experiment is a multipurpose detector designed to study a wide range of processes observed in the high energy proton-antiproton collisions produced by the Fermilab Tevatron. With event rates greater than 1MHz, the CDF-II trigger system is crucial for selecting interesting events for subsequent analysis. This document provides an overview of the Track Extrapolation System (XTRP), a component of the CDF-II trigger system. The XTRP is a fully digital system that is utilized in the track-based selection of high momentum lepton and heavy flavor signatures. The design of the XTRP system includes five different custom boards utilizing discrete and FPGA technology residing in a single VME crate. We describe the design, construction, commissioning and operation of this system.
△ Less
Submitted 28 June, 2006;
originally announced June 2006.
-
Comparison of Three-jet Events in Proton-Antiproton Collisions at Center-of-mass Energy 1.8 TeV to Predictions from a Next-to-leading Order QCD Calculation
Authors:
D. Acosta,
T. Affolder,
M. G. Albrow,
D. Ambrose,
D. Amidei,
K. Anikeev,
J. Antos,
G. Apollinari,
T. Arisawa,
A. Artikov,
W. Ashmanskas,
F. Azfar,
P. Azzi-Bacchetta,
N. Bacchetta,
H. Bachacou,
W. Badgett,
A. Barbaro-Galtieri,
V. E. Barnes,
B. A. Barnett,
S. Baroiant,
M. Barone,
G. Bauer,
F. Bedeschi,
S. Behari,
S. Belforte
, et al. (388 additional authors not shown)
Abstract:
The properties of three-jet events with total transverse energy greater than 320 GeV and individual jet energy greater than 20 GeV have been analyzed and compared to absolute predictions from a next-to-leading order (NLO) perturbative QCD calculation. These data, of integrated luminosity 86 pb^-1, were recorded by the CDF Experiment for proton-antiproton collisions at sqrt{s}=1.8 TeV. This study…
▽ More
The properties of three-jet events with total transverse energy greater than 320 GeV and individual jet energy greater than 20 GeV have been analyzed and compared to absolute predictions from a next-to-leading order (NLO) perturbative QCD calculation. These data, of integrated luminosity 86 pb^-1, were recorded by the CDF Experiment for proton-antiproton collisions at sqrt{s}=1.8 TeV. This study tests a model of higher order QCD processes that result in gluon emission and can be used to estimate the magnitude of the contribution of processes higher than NLO. The total cross section is measured to be 466 +/- 3(stat.)^{+207}_{-70}(syst.) pb. The differential cross section is furthermore measured for all kinematically accessible regions of the Dalitz plane, including those for which the theoretical prediction is unreliable. While the measured cross section is consistent with the theoretical prediction in magnitude, the two differ somewhat in shape in the Dalitz plane.
△ Less
Submitted 6 October, 2004;
originally announced October 2004.