-
The Impact of a Deep-Water Plunging Breaker on a Partially Submerged Cube
Authors:
An Wang,
Christine M. Ikeda,
David A. Drazen,
Anne M. Fullerton,
Thomas Fu,
James H. Duncan
Abstract:
The impact of a plunging breaker on a partially submerged cube is explored experimentally in a wave tank equipped with a programable wave maker. The experiments are conducted with the cube (dimension $L=30.48$ cm) positioned at one streamwise location relative to the wave maker and at three heights relative to the undisturbed water level. A single, repeatable wave maker motion producing a breaker…
▽ More
The impact of a plunging breaker on a partially submerged cube is explored experimentally in a wave tank equipped with a programable wave maker. The experiments are conducted with the cube (dimension $L=30.48$ cm) positioned at one streamwise location relative to the wave maker and at three heights relative to the undisturbed water level. A single, repeatable wave maker motion producing a breaker with a nominal wavelength of 1.18 m is used. The water surface profile at the stream wise vertical center plane of the cube is measured with a cinematic Laser-Induced Fluorescence technique and the impact pressures on the front face of the cube are measured with piezoelectric dynamic pressure transducers. The surface profile measurements and the impact pressure measurements are synchronized. When the cube is positioned vertically so that its bottom face is at either $0.5L$ or $0.25L$ below the undisturbed water surface, the water surface profile behaviors are basically similar with a nearly circular arc forming between the water contact point on the front face of the cube and the wave crest. As the impact proceeds, this arc shrinks to zero size and creates a fast-moving vertical jet in a manner similar to that found in previous studies of wave impact on bottom-mounted vertical walls. In the case where the cube is one quarter submerged, a small jet also forms at the crest and impacts the front face of the cube just before the circular arc reaches zero size. When the bottom of the cube is located at the undisturbed water level the wave impact is dramatically different. In this case, it appears that a packet of air is entrapped during the impact and the surface pressure subsequently oscillates with a frequency of about 2,000 Hz.
△ Less
Submitted 16 December, 2017;
originally announced December 2017.
-
The Impact of a Deep-Water Plunging Breaker
Authors:
Christine Ikeda,
Thomas T. O'Shea,
Kyle A. Brucker,
David A. Drazen,
Douglas G. Dommermuth,
Thomas Fu,
Anne M. Fullerton,
James H. Duncan
Abstract:
The impact of a plunging breaking wave (wavelength approximately 1.3m) on a rigidly mounted rigid cube structure (dimension 0.31m) that is partially submerged is explored through experiments and numerical calculations. The experiments are carried out in a wave tank and the breaker is generated with a mechanical wave maker using a dispersive focusing technique. The water-surface profile upstream of…
▽ More
The impact of a plunging breaking wave (wavelength approximately 1.3m) on a rigidly mounted rigid cube structure (dimension 0.31m) that is partially submerged is explored through experiments and numerical calculations. The experiments are carried out in a wave tank and the breaker is generated with a mechanical wave maker using a dispersive focusing technique. The water-surface profile upstream of the front face of the cube and in its vertical centerplane is measured using a cinematic laser-induced fluorescence technique. The three-dimensional flow in the wave tank is simulated directly using the Numerical Flow Analysis (NFA) code. The experiments and the calculations are used to explore the details of the wave-impact process and, in particular, the formation of the high-speed vertical jet that is found on the front face of the cube under some impact conditions.
△ Less
Submitted 7 October, 2014;
originally announced October 2014.
-
A Comparison of Model-Scale Experimental Measurements and Computational Predictions for a Large Transom-Stern Wave
Authors:
David A. Drazen,
Anne M. Fullerton,
Thomas C. Fu,
Kristine L. C. Beale,
Thomas T. O'Shea,
Kyle A. Brucker,
Douglas G. Dommermuth,
Donald C. Wyatt,
Shanti Bhushan,
Pablo M. Carrica,
Fred Stern
Abstract:
The flow field generated by a transom stern hull form is a complex, broad-banded, three-dimensional system marked by a large breaking wave. This unsteady multiphase turbulent flow feature is difficult to study experimentally and simulate numerically. Recent model-scale experimental measurements and numerical predictions of the wave-elevation topology behind a transom-sterned hull form, Model 5673,…
▽ More
The flow field generated by a transom stern hull form is a complex, broad-banded, three-dimensional system marked by a large breaking wave. This unsteady multiphase turbulent flow feature is difficult to study experimentally and simulate numerically. Recent model-scale experimental measurements and numerical predictions of the wave-elevation topology behind a transom-sterned hull form, Model 5673, are compared and assessed in this paper. The mean height, surface roughness (RMS), and spectra of the breaking stern-waves were measured by Light Detection And Ranging (LiDAR) and Quantitative Visualization (QViz) sensors over a range of model speeds covering both wet- and dry-transom operating conditions. Numerical predictions for this data set from two Office of Naval Research (ONR) supported naval-design codes, Numerical Flow Analysis (NFA) and CFDship-Iowa-V.4, have been performed. Comparisons of experimental data, including LiDAR and QViz measurements, to the numerical predictions for wet-transom and dry transom conditions are presented and demonstrate the current state of the art in the simulation of ship generated breaking waves. This work is part of an ongoing collaborative effort as part of the ONR Ship Wave Breaking and Bubble Wake program, to assess, validate, and improve the capability of Computational Fluid Dynamics (CFD).
△ Less
Submitted 7 October, 2014;
originally announced October 2014.
