Showing 1–44 of 44 results for author: Dorbolo, S

Experimental investigation of exit dynamics of a circular cylinder out of water and silicone oil

Authors: Intesaaf Ashraf, Lionel Vincent, Romain Falla, Jean-Philippe Ponthot, Vincent Terrapon, Benoit Scheid, Stephane Dorbolo

Abstract: Experimental investigations of the exit dynamics of a horizontal cylindrical object were performed in water and silicone oil (50 cSt). The fully immersed cylinder was initially at rest in a still fluid tank before being pushed (or pulled according to the measurement procedure) upwards at a constant velocity. Firstly, we demonstrate that these conditions are better satisfied for a large aspect rati… ▽ More Experimental investigations of the exit dynamics of a horizontal cylindrical object were performed in water and silicone oil (50 cSt). The fully immersed cylinder was initially at rest in a still fluid tank before being pushed (or pulled according to the measurement procedure) upwards at a constant velocity. Firstly, we demonstrate that these conditions are better satisfied for a large aspect ratio cylinder equipped with vertical side plates. Secondly, the influence of the initial depth on the liquid entrained and the wake generated by the cylinder is discussed. The deformation of the bath is found to be independent of the starting depth when the starting depth is larger than 6 times the cylinder diameter. In the present case, this criterion reflects also the finite acceleration of the cylinder to reach the determined constant exit velocity. Measurements in a range of exit speeds between 0.1 and 1 m/s indicate that the thickness of the liquid above the cylinder, when the cylinder starts crossing the interface, increases with the speed according to a logarithmic law of the Froude number. During the subsequent drainage, the evolution of the coated liquid thickness is found to first decrease exponentially with time just after the crossing of the interface. At later times, a change of regime occurs and the drainage follows the inverse of the square root of time irrespective of the crossing speed. Finally, the force necessary to maintain a constant exit speed during the motion of the cylinder inside and outside the bath is analyzed. This global measurement of the entrained liquid confirms the square root scaling of the thinning with time during the drainage process. △ Less

Submitted 24 June, 2024; originally announced June 2024.

Comments: 15 pages, 9 figures

Effect of the Surface Dimples on the Exit Dynamics of a Sphere at a Constant Velocity

Authors: Intesaaf Ashraf, Stephane Dorbolo

Abstract: This article experimentally investigates the exit dynamics of two different spheres i.e. a smooth sphere and a sphere with dimples at a constant speed. Employing high-speed experimental observations, the study investigates the key characteristic lengths and hydrodynamic forces between the sphere's surface and water. The experiments were performed at different traveling speeds (or Froude numbers).… ▽ More This article experimentally investigates the exit dynamics of two different spheres i.e. a smooth sphere and a sphere with dimples at a constant speed. Employing high-speed experimental observations, the study investigates the key characteristic lengths and hydrodynamic forces between the sphere's surface and water. The experiments were performed at different traveling speeds (or Froude numbers). The results shed light on the drag force coefficient, entrainment force coefficient, and cross-over force coefficient. In this paper, we have shown that the surface dimples not only affect the drag force but also the entrainment force. However, the cross-over force coefficient remains the same. △ Less

Submitted 15 January, 2024; v1 submitted 30 October, 2023; originally announced October 2023.

Exit Dynamics of a Square Cylinder

Authors: Intesaaf Ashraf, Stephane Dorbolo

Abstract: In this paper, we experimentally investigate the exit dynamics of a square cylinder, that is initially fully immersed in a water tank and that crosses the interface perpendicularly to its symmetry axis. The cylinder moves upwards at a constant velocity in the vertical direction till the cylinder exits out of the water into the air. The experiments were performed at different traveling speeds. The… ▽ More In this paper, we experimentally investigate the exit dynamics of a square cylinder, that is initially fully immersed in a water tank and that crosses the interface perpendicularly to its symmetry axis. The cylinder moves upwards at a constant velocity in the vertical direction till the cylinder exits out of the water into the air. The experiments were performed at different traveling speeds. The images of the cylinder crossing the interface were taken using a high-speed camera. The images were used to track the interface deformation when the cylinder approaches and crosses the interface. On top of these measurements, the force required to move the cylinder was simultaneously measured in order to estimate the drag force during the travel in the tank, the force of entrainment, and the force of crossing over the interface. Particle image velocimetry was performed to visualize the flow. Correlations between the different measurements are inspected. △ Less

Submitted 27 October, 2023; originally announced October 2023.

Disordering two-dimensional magnet-particle configurations using bidispersity

Authors: K. Tsuchikusa, K. Yamamoto, M. Katsura, C. T. de Paula, J. A. C. Modesto, S. Dorbolo, F. Pacheco-Vázquez, Y. D. Sobral, H. Katsuragi

Abstract: In various types of many-particle systems, bidispersity is frequently used to avoid spontaneous ordering in particle configuration. In this study, the relation between bidispersity and disorder degree of particle configuration is investigated. By using magnetic dipole-dipole interaction, magnet particles are dispersed in a two-dimensional cell without physical contact between them. In this magneti… ▽ More In various types of many-particle systems, bidispersity is frequently used to avoid spontaneous ordering in particle configuration. In this study, the relation between bidispersity and disorder degree of particle configuration is investigated. By using magnetic dipole-dipole interaction, magnet particles are dispersed in a two-dimensional cell without physical contact between them. In this magnetic system, bidispersity is introduced by mixing large and small magnets. Then, the particle system is compressed to produce a uniform particle configuration. The compressed particle configuration is analyzed by using Voronoi tessellation for evaluating the disorder degree which strongly depends on bidispersity. Specifically, standard deviation and skewness of the Voronoi cell area distribution are measured. As a result, we find that the peak of standard deviation is observed when the numbers of large and small particles are almost identical. Although the skewness shows non-monotonic behavior, zero skewness state (symmetric distribution) can be achieved when the numbers of large and small particles are identical. In this ideally random (disordered) state, the ratio between pentagonal, hexagonal, and heptagonal Voronoi cells become roughly identical, while hexagons are dominant in monodisperse (ordered) condition. The relation between Voronoi cell analysis and the global bond orientational order parameter is also discussed. △ Less

Submitted 12 May, 2023; originally announced May 2023.

Comments: 9 pages, 10 figures

Wave turbulence on the surface of a fluid in a high-gravity environment

Authors: Annette Cazaubiel, Sébastien Mawet, Alexis Darras, Galien Grosjean, Jack van Loon, Stéphane Dorbolo, Eric Falcon

Abstract: We report on the observation of gravity-capillary wave turbulence on the surface of a fluid in a high-gravity environment. By using a large-diameter centrifuge, the effective gravity acceleration is tuned up to 20 times the Earth gravity. The transition frequency between the gravity and capillary regimes is thus increased up to one decade as predicted theoretically. A frequency power-law wave spec… ▽ More We report on the observation of gravity-capillary wave turbulence on the surface of a fluid in a high-gravity environment. By using a large-diameter centrifuge, the effective gravity acceleration is tuned up to 20 times the Earth gravity. The transition frequency between the gravity and capillary regimes is thus increased up to one decade as predicted theoretically. A frequency power-law wave spectrum is observed in each regime and is found to be independent of the gravity level and of the wave steepness. While the timescale separation required by weak turbulence is well verified experimentally regardless of the gravity level, the nonlinear and dissipation timescales are found to be independent of the scale, as a result of the finite size effects of the system (large-scale container modes) that are not taken currently into account theoretically. △ Less

Submitted 8 November, 2019; originally announced November 2019.

Comments: in press

Journal ref: Physical Review Letters, American Physical Society, 2019

Leidenfrost drops on a heated liquid pool

Authors: Laurent Maquet, Benjamin Sobac, Baptiste Darbois-Texier, Alexis Duchesne, Martin Brandenbourger, Alexey Rednikov, Pierre Colinet, Stéphane Dorbolo

Abstract: We show that a volatile liquid drop placed at the surface of a non-volatile liquid pool warmer than the boiling point of the drop can experience a Leidenfrost effect even for vanishingly small superheats. Such an observation points to the importance of the substrate roughness, negligible in the case considered here, in determining the threshold Leidenfrost temperature. A theoretical model based on… ▽ More We show that a volatile liquid drop placed at the surface of a non-volatile liquid pool warmer than the boiling point of the drop can experience a Leidenfrost effect even for vanishingly small superheats. Such an observation points to the importance of the substrate roughness, negligible in the case considered here, in determining the threshold Leidenfrost temperature. A theoretical model based on the one proposed by Sobac et al. [Phys. Rev. E 90, 053011 (2014)] is developed in order to rationalize the experimental data. The shapes of the drop and of the substrate are analyzed. The model notably provides scalings for the vapor film thickness. For small drops, these scalings appear to be identical to the case of a Leidenfrost drop on a solid substrate. For large drops, in contrast, they are different and no evidence of chimney formation has been observed either experimentally or theoretically in the range of drop sizes considered in this study. Concerning the evaporation dynamics, the radius is shown to decrease linearly with time whatever the drop size, which differs from the case of a Leidenfrost drop on a solid substrate. For high superheats, the characteristic lifetime of the drops versus the superheat follows a scaling law that is derived from the model but, at low superheats, it deviates from this scaling by rather saturating. △ Less

Submitted 21 March, 2016; v1 submitted 18 March, 2016; originally announced March 2016.

Journal ref: Phys. Rev. Fluids 1, 053902 (2016)

Physics of a toy geyser

Authors: Martin Brandenbourger, Stéphane Dorbolo, Baptiste Darbois Texier

Abstract: A geyser can be reproduced by a toy experiment composed of a water pool located above a water reservoir, the two being connected by a long and narrow tube. When the bottom reservoir is heated, the system experiences periodic eruptions of hot water and steam at the top similarly to the geyser effect occurring in nature. The eruption frequency of a toy geyser is inspected experimentally as a functio… ▽ More A geyser can be reproduced by a toy experiment composed of a water pool located above a water reservoir, the two being connected by a long and narrow tube. When the bottom reservoir is heated, the system experiences periodic eruptions of hot water and steam at the top similarly to the geyser effect occurring in nature. The eruption frequency of a toy geyser is inspected experimentally as a function of the heating power and the height of the set-up. We propose a thermodynamic model of this system which predicts the time between eruptions. Besides, the geometric and thermodynamic conditions required to observe a geyser effect are discussed. The study of the toy geyser is then extended to the case of two reservoirs connected to the same tube. In such a configuration, an eruption in a reservoir may entrain the eruption of the other. Such a coupled system adopts a complex time-evolution which reflects the dynamics of natural geysers. We analyze the behavior of a toy geyser with two reservoirs by the way of statistical tools and develop a theoretical model in order to rationalize our observations. △ Less

Submitted 15 March, 2016; originally announced March 2016.

Wicking through a confined micropillar array

Authors: Baptiste Darbois Texier, Philippe Laurent, Serguei Stoukatch, Stéphane Dorbolo

Abstract: This study considers the spreading of a Newtonian and perfectly wetting liquid in a square array of cylindric micropillars confined between two plates. We show experimentally that the dynamics of the contact line follows a Washburn-like law which depends on the characteristics of the micropillar array (height, diameter and pitch). The presence of pillars can either enhanced or slow down the motion… ▽ More This study considers the spreading of a Newtonian and perfectly wetting liquid in a square array of cylindric micropillars confined between two plates. We show experimentally that the dynamics of the contact line follows a Washburn-like law which depends on the characteristics of the micropillar array (height, diameter and pitch). The presence of pillars can either enhanced or slow down the motion of the contact line. A theoretical model based on capillary and viscous forces has been developed in order to rationalize our observations. Finally, the impact of pillars on the volumic flow rate of liquid which is pumped in the microchannel is inspected. △ Less

Submitted 25 February, 2016; v1 submitted 28 January, 2016; originally announced January 2016.

Rotation of a ice disc during the melting on a solid plate

Authors: S. Dorbolo, N. Vandewalle, B. Darbois-Texier

Abstract: Ice discs were released at the surface of a thermalized aluminium plate. The fusion of the ice creates a lubrication film between the ice disc and the plate. The disc becomes very mobile. The situation is isomorphe to the Leidenfrost effect reported for liquid droplet evaporating at the surface of a plate which temperature is over the boiling temperature of the liquid. For the ice discs, we observ… ▽ More Ice discs were released at the surface of a thermalized aluminium plate. The fusion of the ice creates a lubrication film between the ice disc and the plate. The disc becomes very mobile. The situation is isomorphe to the Leidenfrost effect reported for liquid droplet evaporating at the surface of a plate which temperature is over the boiling temperature of the liquid. For the ice discs, we observe that, while the ice discs were melting, they were rotating. The ice disc rotates starts rotating. The rotation speed increases with the temperature of the plate and with the load put on the ice disc. A model is proposed to explain the spontaneous rotation of the ice disc. We claim that the rotation is due to the viscous entrainment of the ice disc by the liquid that flows around the ice disc. △ Less

Submitted 26 January, 2016; v1 submitted 14 January, 2016; originally announced January 2016.

Comments: 5 pages, 4 figures

Flow of magnetic repelling grains in a two-dimensional silo

Authors: G. Lumay, J. Schockmel, D. Henández-Enríquez, S. Dorbolo, N. Vandewalle, F. Pacheco-Vázquez

Abstract: During a typical silo discharge, the material flow rate is determined by the contact forces between the grains. Here, we report an original study concerning the discharge of a two-dimensional silo filled with repelling magnetic grains. This non-contact interaction leads to a different dynamics from the one observed with conventional granular materials. We found that, although the flow rate depende… ▽ More During a typical silo discharge, the material flow rate is determined by the contact forces between the grains. Here, we report an original study concerning the discharge of a two-dimensional silo filled with repelling magnetic grains. This non-contact interaction leads to a different dynamics from the one observed with conventional granular materials. We found that, although the flow rate dependence on the aperture size follows roughly the power-law with an exponent $3/2$ found in non-repulsive systems, the density and velocity profiles during the discharge are totally different. New phenomena must be taken into account. Despite the absence of contacts, clogging and intermittence were also observed for apertures smaller than a critical size determined by the effective radius of the repulsive grains. △ Less

Submitted 17 October, 2015; originally announced December 2015.

Comments: 6 pages, 8 figures

Journal ref: Papers in Physics 7, 070013 (2015)

Droplets climbing a rotating helical fiber

Authors: Baptiste Darbois Texier, Stéphane Dorbolo

Abstract: A liquid droplet is placed on a rotating helical fiber. We find that the droplet may slide down, attach or climb up the fiber. We inspect experimentally the domain of existence of these three behaviors as a function of the geometrical characteristics of the fiber, its angle relatively to the horizontal, the wetting properties of the fluid and the rotating speed of the helix. A theoretical model is… ▽ More A liquid droplet is placed on a rotating helical fiber. We find that the droplet may slide down, attach or climb up the fiber. We inspect experimentally the domain of existence of these three behaviors as a function of the geometrical characteristics of the fiber, its angle relatively to the horizontal, the wetting properties of the fluid and the rotating speed of the helix. A theoretical model is proposed in order to capture the boundaries of the experimental phase diagram. △ Less

Submitted 30 October, 2015; originally announced October 2015.

Rotation of a melting ice at the surface of a pool

Authors: S. Dorbolo, N. Adami, C. Dubois, H. Caps, N. Vandewalle, B. Darbois-Texier

Abstract: Large circular ice blocks up to 80 m of diameter have been observed on frozen river around the world. This rare event has been reported in a publication in 1993. This fascinating self-fashioned object slowly rotates at about 1$^o$ per second. In this paper, we report a model experiment consisting in a 85 mm of diameter ice disc at the surface of a thermalised pool. The rotation speed has been foun… ▽ More Large circular ice blocks up to 80 m of diameter have been observed on frozen river around the world. This rare event has been reported in a publication in 1993. This fascinating self-fashioned object slowly rotates at about 1$^o$ per second. In this paper, we report a model experiment consisting in a 85 mm of diameter ice disc at the surface of a thermalised pool. The rotation speed has been found to increase with the bath temperature. Using particle image velocimetry technique, we evidence the presence of a vortex below the ice block. This vortex results from the descending flow of high density water at 4$^o$C. The vorticity of the vortex induces the rotation of the ice block. This mechanism is generic of any vertical flow that generates a vortex which induces the rotation of a floating object. △ Less

Submitted 22 October, 2015; originally announced October 2015.

Comments: 5 pages, 7 figures

Journal ref: Phys. Rev. E 93, 033112 (2016)

Toward Bernal Random Loose Packing through freeze-thaw cycling

Authors: F. Ludewig, N. Vandewalle, S. Dorbolo, M. Pakpour, G. Lumay

Abstract: We study the effect of freeze-thaw cycling on the packing fraction of equal spheres immersed in water. The water located between the grains experiences a dilatation during freezing and a contraction during melting. After several cycles, the packing fraction converges to a particular value $η_{\infty} = 0.595$ independently of its initial value $η_0$. This behavior is well reproduced by numerical s… ▽ More We study the effect of freeze-thaw cycling on the packing fraction of equal spheres immersed in water. The water located between the grains experiences a dilatation during freezing and a contraction during melting. After several cycles, the packing fraction converges to a particular value $η_{\infty} = 0.595$ independently of its initial value $η_0$. This behavior is well reproduced by numerical simulations. Moreover, the numerical results allow to analyze the packing structural configuration. With a Voronoï partition analysis, we show that the piles are fully random during the whole process and are characterized by two parameters: the average Voronoï volume $μ_v$ (related to the packing fraction $η$) and the standard deviation $σ_v$ of Voronoï volumes. The freeze-thaw driving modify the volume standard deviation $σ_v$ to converge to a particular disordered state with a packing fraction corresponding to the Random Loose Packing fraction $η_{BRLP}$ obtained by Bernal during his pioneering experimental work. Therefore, freeze-thaw cycling is found to be a soft and spatially homogeneous driving method for disordered granular materials. △ Less

Submitted 27 February, 2015; originally announced February 2015.

Resonant and antiresonant bouncing droplets

Authors: M. Hubert, D. Robert, H. Caps, S. Dorbolo, N. Vandewalle

Abstract: When placed onto a vibrating liquid bath, a droplet may adopt a permanent bouncing behavior, depending on both the forcing frequency and the forcing amplitude. The relationship between the droplet deformations and the bouncing mechanism is studied experimentally and theoretically through an asymmetric and dissipative bouncing spring model. Antiresonance effects are evidenced. Experiments and theor… ▽ More When placed onto a vibrating liquid bath, a droplet may adopt a permanent bouncing behavior, depending on both the forcing frequency and the forcing amplitude. The relationship between the droplet deformations and the bouncing mechanism is studied experimentally and theoretically through an asymmetric and dissipative bouncing spring model. Antiresonance effects are evidenced. Experiments and theoretical predictions show that both resonance at specific frequencies and antiresonance at Rayleigh frequencies play crucial roles in the bouncing mechanism. In particular, we show that they can be exploited for droplet size selection. △ Less

Submitted 11 February, 2014; originally announced February 2014.

Comments: 4 pages, 4 figures and 1 video

MSC Class: 70K40

Magnetic ghosts and monopoles

Authors: N. Vandewalle, S. Dorbolo

Abstract: While the physics of equilibrium systems composed of many particles is well known, the interplay between small-scale physics and global properties is still a mystery for athermal systems. Non-trivial patterns and metastable states are often reached in those systems. We explored the various arrangements adopted by magnetic beads along chains and rings. Here, we show that it is possible to create me… ▽ More While the physics of equilibrium systems composed of many particles is well known, the interplay between small-scale physics and global properties is still a mystery for athermal systems. Non-trivial patterns and metastable states are often reached in those systems. We explored the various arrangements adopted by magnetic beads along chains and rings. Here, we show that it is possible to create mechanically stable defects in dipole arrangements kee** the memory of dipole frustration. Such defects, nicknamed "ghost junctions", seem to act as macroscopic magnetic monopoles, in a way reminiscent of spin ice systems. △ Less

Submitted 27 August, 2013; originally announced August 2013.

Comments: submitted for publication; 5 pages, 4 figures, supplementary files can be obtained upon request

Journal ref: New J. Phys. 16 013050 (2014)

Electrically charged droplet: Influence of the generator configuration and the nature of the liquid

Authors: Martin Brandenbourger, Stephane Dorbolo

Abstract: We studied how to charge droplets by induction and how to maximize this charge. In order to aim this objective, we developed an innovative device that avoids non-linear effects and that is able to charge liquids of different nature. The device developed resembles a planar capacitor. The influence of the nature of the liquid (i.e. presence of ions in solution, polarity, surface tension and conducti… ▽ More We studied how to charge droplets by induction and how to maximize this charge. In order to aim this objective, we developed an innovative device that avoids non-linear effects and that is able to charge liquids of different nature. The device developed resembles a planar capacitor. The influence of the nature of the liquid (i.e. presence of ions in solution, polarity, surface tension and conductivity) on the charge induced was measured. We deduced that there exists a threshold of electrical conductivity for the fluid below which it does not charge according to the "perfect conductor" model. △ Less

Submitted 15 April, 2013; originally announced April 2013.

Comments: 6 pages, 5 figures

The role of the droplet deformations in the bouncing droplet dynamics

Authors: Denis Terwagne, François Ludewig, Nicolas Vandewalle, Stéphane Dorbolo

Abstract: Droplets bouncing on a vibrated liquid bath open ways to methods of manipulating droplets, creating double emulsion and performing pilot wave model experiments. In this work, we focus on the role of the droplet deformations in the vertical bouncing dynamics by neglecting the deformation of the surface of the bath. To be under this favorable conditions, low viscous oil droplet are dropped over a hi… ▽ More Droplets bouncing on a vibrated liquid bath open ways to methods of manipulating droplets, creating double emulsion and performing pilot wave model experiments. In this work, we focus on the role of the droplet deformations in the vertical bouncing dynamics by neglecting the deformation of the surface of the bath. To be under this favorable conditions, low viscous oil droplet are dropped over a highly viscous oil bath. These droplets bounce vertically on the surface of the bath and exhibit many periodic trajectories and resonant modes when tuning the forcing parameters, i.e. the oscillation of the bath. This complex dynamics emphasizes the interplay between elastic energy storage and energy dissipation in droplets at each bounce. We propose to model droplets using a bouncing mass-spring-damper system that mimics a deformable droplet bouncing on a non-deformable liquid bath. From the experimental measurements, we constructed bifurcation diagrams of the bouncing trajectories and challenged our bouncing spring model. The agreement between experiment and the spring model reveals that this model can be used to rationalize and predict a variety of bouncing droplets behaviors involving multi-periodicities. △ Less

Submitted 3 December, 2013; v1 submitted 30 January, 2013; originally announced January 2013.

Comments: 12 pages, 6 figures

MSC Class: 76-XX; 74Axx

Leidenfrost explosions

Authors: F. Moreau, P. Colinet, S. Dorbolo

Abstract: We present a fluid dynamics video showing the behavior of Leidenfrost droplets composed by a mixture of water and surfactant (SDS, Sodium Dodecyl sulfate). When a droplet is released on a plate heated above a given temperature a thin layer of vapor isolates the droplet from the plate. The droplet levitates over the plate. This is called the Leidenfrost effect. In this work we study the influen… ▽ More We present a fluid dynamics video showing the behavior of Leidenfrost droplets composed by a mixture of water and surfactant (SDS, Sodium Dodecyl sulfate). When a droplet is released on a plate heated above a given temperature a thin layer of vapor isolates the droplet from the plate. The droplet levitates over the plate. This is called the Leidenfrost effect. In this work we study the influence of the addition of a surfactant on the Leidenfrost phenomenon. As the droplet evaporates the concentration of SDS rises up to two orders of magnitude over the Critical Micelle Concentration (CMC). An unexpected and violent explosive behavior is observed. The video presents several explosions taken with a high speed camera (IDT-N4 at 30000 fps). All the presented experiments were performed on a plate heated at 300°C. On the other hand, the initial quantity of SDS was tuned in two ways: (i) by varying the initial concentration of SDS and (ii) by varying the initial size of the droplet. By measuring the volume of the droplet just before the explosion, we were able to estimate the final concentration of SDS. We found that the explosion always occurs around a critical concentration, about 100 times the CMC. The droplets have also been studied just before the explosion. By isolating the droplet on a cold plate just before the explosion, we evidenced the presence of a shell surrounding a liquid core. We conclude that above a critical concentration a solid shell is formed. This leads to an increase of pressure into the droplet until the shell breaks. The release of the pressure is accompanied by a violent explosion, and in some cases foaming. △ Less

Submitted 13 October, 2012; originally announced October 2012.

Comments: 1 page, 2 videos included, submission to Gallery of Fluid Motion 2012

Wave turbulence on the surface of a ferrofluid in a horizontal magnetic field

Authors: Stéphane Dorbolo, Eric Falcon

Abstract: We report observations of wave turbulence on the surface of a ferrofluid submitted to a magnetic field parallel to the fluid surface. The magnetic wave turbulence shows several differences compared to the normal field case reported recently. The inertial zone of the magnetic wave turbulence regime is notably found to be strongly increased with respect to the normal field case, and to be well descr… ▽ More We report observations of wave turbulence on the surface of a ferrofluid submitted to a magnetic field parallel to the fluid surface. The magnetic wave turbulence shows several differences compared to the normal field case reported recently. The inertial zone of the magnetic wave turbulence regime is notably found to be strongly increased with respect to the normal field case, and to be well described by our theoretical predictions. The dispersion relation of linear waves is also measured and differs from the normal field case due to the absence of the Rosensweig instability. △ Less

Submitted 30 March, 2011; originally announced March 2011.

Comments: in press in Phys. Rev. E (2011)

Journal ref: Physical Review E 83 (2011) 046303

Freezing Splashes

Authors: G. Delon, D. Terwagne, N. Adami, A. Bronfort, N. Vandewalle, S. Dorbolo, H. Caps

Abstract: We have studied the splashing dynamics of water drops impacting granular layers. Depending on the drop kinetic energy, various shapes are observed for the resulting craters. Experimental parameters that have been considered are : the size of the millimetric droplets; the height of the free fall, ranging from 1.5 cm to 100 cm; and the diameter of the grains. As the drop is impacting the granular la… ▽ More We have studied the splashing dynamics of water drops impacting granular layers. Depending on the drop kinetic energy, various shapes are observed for the resulting craters. Experimental parameters that have been considered are : the size of the millimetric droplets; the height of the free fall, ranging from 1.5 cm to 100 cm; and the diameter of the grains. As the drop is impacting the granular layer, energy is dissipated and a splash of grain occurs. Meanwhile, surface tension, inertia and viscosity compete, leading to strong deformations of the drop which depend on the experimental conditions. Just after the drop enters into contact with the granular bed, imbibition takes place and increases the apparent viscosity of the fluid. The drop motion is stopped by this phenomenon. Images and fast-video recordings of the impacts allowed to find scaling laws for the crater morphology and size. This abstract is related to a fluid dynamics video for the APS DFD gallery of fluid motion 2010. △ Less

Submitted 15 October, 2010; originally announced October 2010.

Comments: This abstract is related to a fluid dynamics video for the APS DFD gallery of fluid motion 2010

A fountain of droplets

Authors: D. Terwagne, G. Delon, N. Adami, N. Vandewalle, H. Caps, S. Dorbolo

Abstract: A vessel is plunged upside down into a pool of 50 cSt silicone oil. An air bell is then created. This bell is vertically shaken at 60 Hz that leads to the oscillation of the air/oil interface. The edges of the immersed vessel generate surface waves that propagate towards the center of the bell. When the amplitude of the oscillation increases, wave amplitude increases. We study the influence of the… ▽ More A vessel is plunged upside down into a pool of 50 cSt silicone oil. An air bell is then created. This bell is vertically shaken at 60 Hz that leads to the oscillation of the air/oil interface. The edges of the immersed vessel generate surface waves that propagate towards the center of the bell. When the amplitude of the oscillation increases, wave amplitude increases. We study the influence of the angle between successive sides on the wave patterns. Two kinds of vessel have been studied: a triangular and a square prism. The shape of the air/oil meniscus depends on the angle between the sides of the considered prism. As the amplitude of the oscillation is increased, the triple line, which is the contact line between the solid and the air/oil interface, moves up and down. Above a given acceleration that depends on the immersion depth and on the shape vessel, wave goes under the corner edge of the bell. During the oscillation, the wave generates at the edges presents a singularity that leads eventually to a jet and a drop ejection. A drop is ejected at each oscillation. More complicated ejection can be produced with further increase of the amplitude. This is a sample arXiv article illustrating the use of fluid dynamics videos. △ Less

Submitted 15 October, 2010; originally announced October 2010.

Comments: 3 pages, 2 figures, 2 movies (high-res and low-res)

Faraday instability on a network

Authors: G. Delon, D. Terwagne, N. Vandewalle, S. Dorbolo, H. Caps

Abstract: Faraday waves are generated at the air/liquid interface inside an array of square cells. As the free surface inside each cell is destabilizing due to the oscillations, the shape of the free surface is drastically changing. Depending on the value of the frequency f of oscillations, different patterns are observed inside each cell. For well defined f values, neighboring cells are observed to inter… ▽ More Faraday waves are generated at the air/liquid interface inside an array of square cells. As the free surface inside each cell is destabilizing due to the oscillations, the shape of the free surface is drastically changing. Depending on the value of the frequency f of oscillations, different patterns are observed inside each cell. For well defined f values, neighboring cells are observed to interact and a general organization is noticed. In such a situation, initially disordered structures lead to a general pattern covering the entire liquid pool and a spatial order appears all over the cell array. This abstract is related to a fluid dynamics video for the gallery of fluid motion 2009. △ Less

Submitted 16 October, 2009; v1 submitted 15 October, 2009; originally announced October 2009.

Comments: This abstract is related to a fluid dynamics video for the gallery of fluid motion 2009

Antibubbles in a cyclone eyewall

Authors: D. Terwagne, G. Delon, N. Vandewalle, H. Caps, S. Dorbolo

Abstract: A negative bubble, coined antibubble, is composed by a thin air shell that is immersed in a soapy mixture. A large vortex is generated in the liquid using a mixer. An antibubble is then created close to the surface. The antibubble is fastly attracted by the vortex. It rotates arount the core and comes closer and closer. When the stress is large enough, the vortex deforms the antibubble that wind… ▽ More A negative bubble, coined antibubble, is composed by a thin air shell that is immersed in a soapy mixture. A large vortex is generated in the liquid using a mixer. An antibubble is then created close to the surface. The antibubble is fastly attracted by the vortex. It rotates arount the core and comes closer and closer. When the stress is large enough, the vortex deforms the antibubble that winds around the eye vortex. The antibubble looks like a spiral. Under some conditions, the antibubble splits into several antibubbles that are ejected out of the eye vortex while the largest part is still trapped the vortex. This latter is elongated and is absorbed to the bottom of the tank before pop**. fluid dynamics video △ Less

Submitted 15 October, 2009; originally announced October 2009.

Comments: 3 pages, 1 figures, Gallery of fluid motion, fluid dynamics video

Compaction dynamics of a magnetized powder

Authors: G. Lumay, S. Dorbolo, N. Vandewalle

Abstract: We have investigated experimentally the influence of a magnetic interaction between the grains on the compaction dynamics of a granular pile submitted to a series of taps. The granular material used to perform this study is a mixture of metallic and glass grains. The packing is immersed in an homogeneous external magnetic field. The magnetic field induces an interaction between the metallic grai… ▽ More We have investigated experimentally the influence of a magnetic interaction between the grains on the compaction dynamics of a granular pile submitted to a series of taps. The granular material used to perform this study is a mixture of metallic and glass grains. The packing is immersed in an homogeneous external magnetic field. The magnetic field induces an interaction between the metallic grains that constitutes the tunable cohesion. The compaction characteristic time and the asymptotic packing fraction have been measured as a function of the Bond number which is the ratio between the cohesive magnetic force and the grain weight. These measurements have been performed for different fractions of metallic beads in the pile. When the pile is only made of metallic grains, the characteristic compaction time increases as the square root of the Bond number. While the asymptotic packing fraction decreases as the inverse of the Bond number. For mixtures, when the fraction of magnetized grains in the pile is increased, the characteristic time increases while the asymptotic packing fraction decreases. A simple mesoscopic model based on the formation of granular chains along the magnetic field direction is proposed to explain the observed macroscopic properties of the packings. △ Less

Submitted 3 July, 2009; originally announced July 2009.

Bouncing trimer: a random self-propelled particle, chaos and periodical motions

Authors: S. Dorbolo, F. Ludewig, N. Vandewalle

Abstract: A trimer is an object composed of three centimetrical stainless steel beads equally distant and is predestined to show richer behaviours than the bouncing ball or the bouncing dimer. The rigid trimer has been placed on a plate of a electromagnetic shaker and has been vertically vibrated according to a sinusoidal signal. The horizontal translational and rotational motions of the trimer have been… ▽ More A trimer is an object composed of three centimetrical stainless steel beads equally distant and is predestined to show richer behaviours than the bouncing ball or the bouncing dimer. The rigid trimer has been placed on a plate of a electromagnetic shaker and has been vertically vibrated according to a sinusoidal signal. The horizontal translational and rotational motions of the trimer have been recorded for a range of frequencies between 25 and 100 Hz while the amplitude of the forcing vibration was tuned for obtaining maximal acceleration of the plate up to 10 times the gravity. Several modes have been detected like e.g. rotational and pure translational motions. These modes are found at determined accelerations of the plate and do not depend on the frequency. By recording the time delays between two successive contacts when the frequency and the amplitude are fixed, a map** of the bouncing regime has been constructed and compared to that of the dimer and the bouncing ball. Period-2 and period-3 orbits have been experimentally observed. In these modes, according to observations, the contact between the trimer and the plate is persistent between two successive jumps. This persistence erases the memory of the jump preceding the contact. A model is proposed and allows to explain the values of the particular accelerations for which period-2 and period-3 modes are observed. Finally, numerical simulations allow to reproduce the experimental results. That allows to conclude that the friction between the beads and the plate is the major dissipative process. △ Less

Submitted 21 August, 2008; originally announced August 2008.

Comments: 22 pages, 10 figures

Resonant and rolling droplet

Authors: S. Dorbolo, D. Terwagne, N. Vandewalle, T. Gilet

Abstract: When an oil droplet is placed on a quiescent oil bath, it eventually collapses into the bath due to gravity. The resulting coalescence may be eliminated when the bath is vertically vibrated. The droplet bounces periodically on the bath, and the air layer between the droplet and the bath is replenished at each bounce. This sustained bouncing motion is achieved when the forcing acceleration is hig… ▽ More When an oil droplet is placed on a quiescent oil bath, it eventually collapses into the bath due to gravity. The resulting coalescence may be eliminated when the bath is vertically vibrated. The droplet bounces periodically on the bath, and the air layer between the droplet and the bath is replenished at each bounce. This sustained bouncing motion is achieved when the forcing acceleration is higher than a threshold value. When the droplet has a sufficiently low viscosity, it significantly deforms : spherical harmonic \boldmath{$Y_{\ell}^m$} modes are excited, resulting in resonant effects on the threshold acceleration curve. Indeed, a lower acceleration is needed when $\ell$ modes with $m=0$ are excited. Modes $m \ne 0$ are found to decrease the bouncing ability of the droplet. When the mode $\ell=2$ and $m=1$ is excited, the droplet rolls on the vibrated surface without touching it, leading to a new self-propulsion mode. △ Less

Submitted 30 June, 2008; originally announced June 2008.

Comments: 4 pages, 6 figures

How long will a bubble be ?

Authors: T. Gilet, T. Scheller, E. Reyssat, N. Vandewalle, S. Dorbolo

Abstract: A soap bubble is a metastable object that eventually breaks. Indeed, the soapy water film thins until rupture, due to drainage and evaporation. In our experimental investigations, floating bubbles at the surface of a liquid bath have been considered. Their lifetime has been measured and reported with respect to their radius. Large bubbles last longer than small ones. Moreover, small bubbles have… ▽ More A soap bubble is a metastable object that eventually breaks. Indeed, the soapy water film thins until rupture, due to drainage and evaporation. In our experimental investigations, floating bubbles at the surface of a liquid bath have been considered. Their lifetime has been measured and reported with respect to their radius. Large bubbles last longer than small ones. Moreover, small bubbles have more predictable lifetimes than large ones. We propose a general equation for that lifetime, based on the lubrication theory. The evaporation is shown to be an essential process which determines the bubble lifetime. △ Less

Submitted 27 September, 2007; originally announced September 2007.

Comments: 4 pages, 4 figures, submitted to Phys.Rev.Lett

About the lifetime of a bouncing droplet

Authors: D. Terwagne, S. Dorbolo, N. Vandewalle

Abstract: When a droplet is gently laid onto the surface of the same liquid, it stays at rest for a moment before coalescence. The coalescence can be delayed and sometimes inhibited by injecting fresh air under the droplet. This can happen when the surface of the bath oscillates vertically, in this case the droplet basically bounces on the interface. The lifetime of the droplet has been studied with respe… ▽ More When a droplet is gently laid onto the surface of the same liquid, it stays at rest for a moment before coalescence. The coalescence can be delayed and sometimes inhibited by injecting fresh air under the droplet. This can happen when the surface of the bath oscillates vertically, in this case the droplet basically bounces on the interface. The lifetime of the droplet has been studied with respect to the amplitude and the frequency of the excitation. The lifetime decreases when the acceleration increases. The thickness of the air film between the droplet and the bath has been investigated using interference fringes obtained when the system is illuminated by low pressure sodium lamps. Moreover, both the shape evolution and the motion of the droplet center of mass have been recorded in order to evidence the phase offset between the deformation and the trajectory. A short lifetime is correlated to a small air film thickness and to a large phase offset between the maximum of deformation and the minimum of the vertical position of the centre of mass. △ Less

Submitted 30 May, 2007; originally announced May 2007.

Comments: (5 pages, 7 figures)

Effects of electromagnetic waves on the electrical properties of contacts between grains

Authors: S. Dorbolo, A. Merlen, M. Creyssels, N. Vandewalle, B. Castaing, E. Falcon

Abstract: A DC electrical current is injected through a chain of metallic beads. The electrical resistances of each bead-bead contacts are measured. At low current, the distribution of these resistances is large and log-normal. At high enough current, the resistance distribution becomes sharp and Gaussian due to the creation of microweldings between some beads. The action of nearby electromagnetic waves (… ▽ More A DC electrical current is injected through a chain of metallic beads. The electrical resistances of each bead-bead contacts are measured. At low current, the distribution of these resistances is large and log-normal. At high enough current, the resistance distribution becomes sharp and Gaussian due to the creation of microweldings between some beads. The action of nearby electromagnetic waves (sparks) on the electrical conductivity of the chain is also studied. The spark effect is to lower the resistance values of the more resistive contacts, the best conductive ones remaining unaffected by the spark production. The spark is able to induce through the chain a current enough to create microweldings between some beads. This explains why the electrical resistance of a granular medium is so sensitive to the electromagnetic waves produced in its vicinity. △ Less

Submitted 6 July, 2007; v1 submitted 12 May, 2007; originally announced May 2007.

Comments: 4 pages, 5 figures

Controlling the partial coalescence of a droplet on a vertically vibrated bath

Authors: T. Gilet, N. Vandewalle, S. Dorbolo

Abstract: A new method is proposed to stop the cascade of partial coalescences of a droplet laid on a liquid bath. The strategy consists in vibrating the bath in the vertical direction in order to keep small droplets bouncing. Since large droplets are not able to bounce, they partially coalesce until they reach a critical size. The system behaves as a low pass filter : droplets smaller than the critical s… ▽ More A new method is proposed to stop the cascade of partial coalescences of a droplet laid on a liquid bath. The strategy consists in vibrating the bath in the vertical direction in order to keep small droplets bouncing. Since large droplets are not able to bounce, they partially coalesce until they reach a critical size. The system behaves as a low pass filter : droplets smaller than the critical size are selected. This size has been investigated as a function of the acceleration and the frequency of the bath vibration. Results suggest that the limit size for bouncing is related to the first mode of the droplet deformation. △ Less

Submitted 22 August, 2007; v1 submitted 27 February, 2007; originally announced February 2007.

Comments: 4 pages, 3 figures, accepted in Phys. Rev. E

Journal ref: Phys. Rev. E 76, 035302(R) (2007)

Some aspects of electrical conduction in granular systems of various dimensions

Authors: Mathieu Creyssels, Stéphane Dorbolo, Alexandre Merlen, Claude Laroche, Bernard Castaing, Eric Falcon

Abstract: We report on measurements of the electrical conductivity in both a 2D triangular lattice of metallic beads and in a chain of beads. The voltage/current characteristics are qualitatively similar in both experiments. At low applied current, the voltage is found to increase logarithmically in a good agreement with a model of widely distributed resistances in series. At high enough current, the volt… ▽ More We report on measurements of the electrical conductivity in both a 2D triangular lattice of metallic beads and in a chain of beads. The voltage/current characteristics are qualitatively similar in both experiments. At low applied current, the voltage is found to increase logarithmically in a good agreement with a model of widely distributed resistances in series. At high enough current, the voltage saturates due to the local welding of microcontacts between beads. The frequency dependence of the saturation voltage gives an estimate of the size of these welded microcontacts. The DC value of the saturation voltage (~ 0.4 V per contact) gives an indirect measure of the number of welded contact carrying the current within the 2D lattice. Also, a new measurement technique provides a map of the current paths within the 2D lattice of beads. For an isotropic compression of the 2D granular medium, the current paths are localized in few discrete linear paths. This quasi-onedimensional nature of the electrical conductivity thus explains the similarity between the characteristics in the 1D and 2D systems. △ Less

Submitted 18 July, 2007; v1 submitted 6 November, 2006; originally announced November 2006.

Comments: To be published in The European Physical Journal E

Journal ref: The European Physical Journal E 03, 23 (2007) 255-264

Critical parameters for the partial coalescence of a droplet

Authors: T. Gilet, K. Mulleners, J. P. Lecomte, N. Vandewalle, S. Dorbolo

Abstract: The partial coalescence of a droplet onto a planar liquid/liquid interface is investigated experimentally by tuning the viscosities of both liquids. The problem mainly depends on four dimensionless parameters: the Bond number (gravity vs. surface tension), the Ohnesorge numbers (viscosity in both fluids vs. surface tension), and the density relative difference. The ratio between the daughter dro… ▽ More The partial coalescence of a droplet onto a planar liquid/liquid interface is investigated experimentally by tuning the viscosities of both liquids. The problem mainly depends on four dimensionless parameters: the Bond number (gravity vs. surface tension), the Ohnesorge numbers (viscosity in both fluids vs. surface tension), and the density relative difference. The ratio between the daughter droplet size and the mother droplet size is investigated as a function of these dimensionless numbers. Global quantities such as the available surface energy of the droplet has been measured during the coalescence. The capillary waves propagation and dam** are studied in detail. The relation between these waves and the partial coalescence is discussed. Additional viscous mechanisms are proposed in order to explain the asymmetric role played by both viscosities. △ Less

Submitted 15 December, 2006; v1 submitted 11 August, 2006; originally announced August 2006.

Comments: 16 pages, 14 figures, submitted to Physical Review E

Journal ref: Phys. Rev. E 75, 036303 (2007)

Dynamics of a bouncing dimer

Authors: S. Dorbolo, D. Volfson, L. Tsimring, A. Kudrolli

Abstract: We investigate the dynamics of a dimer bouncing on a vertically oscillated plate. The dimer, composed of two spheres rigidly connected by a light rod, exhibits several modes depending on initial and driving conditions. The first excited mode has a novel horizontal drift in which one end of the dimer stays on the plate during most of the cycle, while the other end bounces in phase with the plate.… ▽ More We investigate the dynamics of a dimer bouncing on a vertically oscillated plate. The dimer, composed of two spheres rigidly connected by a light rod, exhibits several modes depending on initial and driving conditions. The first excited mode has a novel horizontal drift in which one end of the dimer stays on the plate during most of the cycle, while the other end bounces in phase with the plate. The speed and direction of the drift depend on the aspect ratio of the dimer. We employ event-driven simulations based on a detailed treatment of frictional interactions between the dimer and the plate in order to elucidate the nature of the transport mechanism in the drift mode. △ Less

Submitted 7 June, 2005; originally announced June 2005.

Comments: 4 pages, 5 figures, Movies: http://physics.clarku.edu/~akudrolli/dimer

Journal ref: Phys. Rev. Lett. 95, 044101 (2005)

Effect of friction in a toy model of granular compaction

Authors: F. Ludewig, S. Dorbolo, N. Vandewalle

Abstract: We proposed a toy model of granular compaction which includes some resistance due to granular arches. In this model, the solid/solid friction of contacting grains is a key parameter and a slip** threshold Wc is defined. Realistic compaction behaviors have been obtained. Two regimes separated by a critical point Wc* of the slip** threshold have been emphasized : (i) a slow compaction with lot… ▽ More We proposed a toy model of granular compaction which includes some resistance due to granular arches. In this model, the solid/solid friction of contacting grains is a key parameter and a slip** threshold Wc is defined. Realistic compaction behaviors have been obtained. Two regimes separated by a critical point Wc* of the slip** threshold have been emphasized : (i) a slow compaction with lots of paralyzed regions, and (ii) an inverse logarithmic dynamics with a power law scaling of grain mobility. Below the critical point Wc*, the physical properties of this frozen system become independent of Wc. Above the critical point Wc*, i.e. for low friction values, the packing properties behave as described by the classical Janssen theory for silos. △ Less

Submitted 13 May, 2004; originally announced May 2004.

Rolling/Slip** Motion of Euler's Disk

Authors: H. Caps, S. Dorbolo, S. Ponte, H. Croisier, N. Vandewalle

Abstract: We present an experimental study of the motion of a circular disk spun onto a table. With the help of a high speed video system, the temporal evolutions of (i) the inclination angle $α$, (ii) the angular velocity $ω$ and (iii) the precession rate $Ω$ are studied. The influence of the mass of the disk and the friction between the disk and the supporting surface are considered. %The motions of dis… ▽ More We present an experimental study of the motion of a circular disk spun onto a table. With the help of a high speed video system, the temporal evolutions of (i) the inclination angle $α$, (ii) the angular velocity $ω$ and (iii) the precession rate $Ω$ are studied. The influence of the mass of the disk and the friction between the disk and the supporting surface are considered. %The motions of disks with different masses and over different surfaces are studied. The inclination angle $α$ and the angular velocity are observed to decrease according to a power law. We also show that the precession rate $Ω$ diverges as the disk stops. Exponents are measured very near the collapse as well as on long range times. Collapsing times have been also measured. The results are compared with previous theoretical and experimental works. The major source of energy dissipation is found to be the slip** of the disk on the plane. △ Less

Submitted 16 January, 2004; originally announced January 2004.

Comments: Submitted for publication (2003) - 6pages

Aging process of electrical contacts in granular matter

Authors: S. Dorbolo, M. Ausloos, N. Vandewalle, M. Houssa

Abstract: The electrical resistance decay of a metallic granular packing has been measured as a function of time. This measurement gives information about the size of the conducting cluster formed by the well connected grains. Several regimes have been encountered. Chronologically, the first one concerns the growth of the conducting cluster and is identified to belong to diffusion processes through a stre… ▽ More The electrical resistance decay of a metallic granular packing has been measured as a function of time. This measurement gives information about the size of the conducting cluster formed by the well connected grains. Several regimes have been encountered. Chronologically, the first one concerns the growth of the conducting cluster and is identified to belong to diffusion processes through a stretched exponential behavior. The relaxation time is found to be simply related to the initial injected power. This regime is followed by a reorganisation process due to thermal dilatation. For the long term behavior of the decay, an aging process occurs and enhances the electrical contacts between grains through microsoldering. △ Less

Submitted 15 October, 2003; originally announced October 2003.

Comments: 11 pages, 4 figures

Journal ref: J. Appl. Phys. 94 (2003) 7835-7838

Analysis of Experimental Conditions for Simultaneous Measurements of Transport and Magnetotransport Coefficients of High Temperature Superconductors

Authors: J. Mucha, S. Dorbolo, H. Bougrine, K. Durczewski, M. Ausloos

Abstract: Experimental conditions for simultaneous measurements of transport coefficients of high temperature superconductors in zero and non-zero magnetic fields are analysed. Test measurements of the thermal conductivity, the thermoelectric power and the Nernst - Ettingshausen effect of a textured Bi2212 sample are reported in an external magnetic field of 2T. Errors related to parameters of the thermoc… ▽ More Experimental conditions for simultaneous measurements of transport coefficients of high temperature superconductors in zero and non-zero magnetic fields are analysed. Test measurements of the thermal conductivity, the thermoelectric power and the Nernst - Ettingshausen effect of a textured Bi2212 sample are reported in an external magnetic field of 2T. Errors related to parameters of the thermocouple used and to the spurious heat flows are discussed for a new experimental set-up built based on a closed cycle helium refrigerator. Possible optimising of experimental conditions is suggested. △ Less

Submitted 30 September, 2003; originally announced September 2003.

Comments: 9 pages + 4 figures. accepted for publication in Cryogenics

Journal ref: Cryogenics 44 (2004) 145-149

Antibubbles: evidences of a critical pressure

Authors: S. Dorbolo, N. Vandewalle

Abstract: We present experimental investigations of antibubbles. Such an unusual fluid object is a thin spherical air shell surrounding a liquid globule. We explain how to produce them and we study their stability. By overweighting antibubbles with a small amount of salt, they sink and pop at a definite depth. A critical depth related to a critical pressure has been found. A modified Laplace law describes… ▽ More We present experimental investigations of antibubbles. Such an unusual fluid object is a thin spherical air shell surrounding a liquid globule. We explain how to produce them and we study their stability. By overweighting antibubbles with a small amount of salt, they sink and pop at a definite depth. A critical depth related to a critical pressure has been found. A modified Laplace law describes the air shell thickness evolution with respect to pressure. This law combined with surfactant layers interaction allows to explain the critical depth for antibubble stability. △ Less

Submitted 7 May, 2003; originally announced May 2003.

Comments: 4 pages, 8 figures

Limit current density in 2D metallic granular packings

Authors: S. Dorbolo, M. Ausloos, N. Vandewalle

Abstract: The electrical properties 2D of packed metallic pentagons have been studied. The characterization of such metallic pentagon heaps (like $i-V$ measurements) has been achieved and has allowed to point out two distinct conduction regimes. They are separated by a transition line along which the system exhibits a memory effect behavior due to the irreversible improvement of electrical contacts betwee… ▽ More The electrical properties 2D of packed metallic pentagons have been studied. The characterization of such metallic pentagon heaps (like $i-V$ measurements) has been achieved and has allowed to point out two distinct conduction regimes. They are separated by a transition line along which the system exhibits a memory effect behavior due to the irreversible improvement of electrical contacts between pentagons (hot spots). A limit current density has been found. △ Less

Submitted 14 February, 2003; originally announced February 2003.

Comments: 4 pages, 6 figures

Magnon-polaron and Spin-polaron Signatures in the Specific Heat and Electrical Resistivity of $La_{0.6}Y_{0.1}Ca_{0.3}MnO_3$ in Zero Magnetic Field, and the Effect of $Mn-O-Mn$ Bond Environment

Authors: M. Ausloos, L. Hubert, S. Dorbolo, A. Gilabert, R. Cloots

Abstract: $La_{0.6}Y_{0.1}Ca_{0.3}MnO_{3}$, an $ABO_{3}$ perovskite manganite oxide, exhibits a non trivial behavior in the vicinity of the sharp peak found in the resistivity $ρ$ as a function of temperature $T$ in zero magnetic field. The various features seen on $dρ/dT$ are discussed in terms of competing phase transitions. They are related to the $Mn-O-Mn$ bond environment depending on the content of… ▽ More $La_{0.6}Y_{0.1}Ca_{0.3}MnO_{3}$, an $ABO_{3}$ perovskite manganite oxide, exhibits a non trivial behavior in the vicinity of the sharp peak found in the resistivity $ρ$ as a function of temperature $T$ in zero magnetic field. The various features seen on $dρ/dT$ are discussed in terms of competing phase transitions. They are related to the $Mn-O-Mn$ bond environment depending on the content of the $A$ crystallographic site. A Ginzburg-Landau type theory is presented for incorporating concurrent phase transitions. The specific heat $C$ of such a compound is also examined from 50 till 200 K. A log-log analysis indicates different regimes. In the low temperature conducting ferromagnetic phase, a collective magnon signature ($C \simeq T^{3/2}$) is found as for what are called magnon-polaron excitations. A $C \simeq T^{2/3}$ law is found at high temperature and discussed in terms of the fractal dimension of the conducting network of the weakly conducting (so-called insulating) phase and Orbach estimate of the excitation spectral behaviors. The need of considering both independent spin scattering and collective spin scattering is thus emphasized. The report indicates a remarkable agreement for the Fisher-Langer formula, i.e. $C$ $\sim$ $dρ/dT$ at second order phase transitions. Within the Attfield model, we find an inverse square root relationship between the critical temperature(s) and the total local $Mn-O-Mn$ strain. △ Less

Submitted 14 September, 2002; originally announced September 2002.

Comments: 19 pages, 5 figures; to be published in Phys Rev B

Influence of a low magnetic field on the thermal diffusivity of Bi-2212

Authors: S. Dorbolo, M. Ausloos

Abstract: The thermal diffusivity of a Bi-2212 polycrystalline sample has been measured under a 1T magnetic field applied perpendicularly to the heat flux. The magnetic contribution to the heat carrier mean free path has been extracted and is found to behave as a simple power law. This behavior can be attributed to a percolation process of electrons in the vortex lattice created by the magnetic field. The thermal diffusivity of a Bi-2212 polycrystalline sample has been measured under a 1T magnetic field applied perpendicularly to the heat flux. The magnetic contribution to the heat carrier mean free path has been extracted and is found to behave as a simple power law. This behavior can be attributed to a percolation process of electrons in the vortex lattice created by the magnetic field. △ Less

Submitted 11 May, 2002; originally announced May 2002.

Comments: 10 pages, 3 figures; to be published in Phys. Rev. B

Quasiparticle contribution to heat carriers relaxation time in DyBa$_2$Cu$_3$O$_{7-x}$ from heat diffusivity measurements

Authors: S. Dorbolo, M. Ausloos

Abstract: It is shown that the controversy on phonons or electrons being the most influenced heat carriers below the critical temperature of high-T$_c$ superconductors can be resolved. Electrical and thermal properties of the same DyBa$_2$Cu$_3$O$_{7-x}$ monodomain have been measured for two highly different oxygenation levels. While the oxygenated sample DyBa$_2$Cu$_3$O$_{7}$ has very good superconductin… ▽ More It is shown that the controversy on phonons or electrons being the most influenced heat carriers below the critical temperature of high-T$_c$ superconductors can be resolved. Electrical and thermal properties of the same DyBa$_2$Cu$_3$O$_{7-x}$ monodomain have been measured for two highly different oxygenation levels. While the oxygenated sample DyBa$_2$Cu$_3$O$_{7}$ has very good superconducting properties ($T_c=90$ K), the DyBa$_2$Cu$_3$O$_{6.3}$ sample exhibits an insulator behavior. A careful comparison between measurements of the {\bf thermal diffusivity} of both samples allows us to extract the electronic contribution. This contribution to the relaxation time of heat carriers is shown to be large below $T_c$ and more sensitive to the superconducting state than the phonon contribution. △ Less

Submitted 23 August, 2001; originally announced August 2001.

Comments: 13 pages, 6 figures

Avalanches of pop** bubbles in collapsing foams

Authors: N. Vandewalle, J. F. Lentz, S. Dorbolo, F. Brisbois

Abstract: We report acoustic experiments on foam systems. We have recorded the sound emitted by crackling cells during the collapsing of foams. The sound pattern is then analyzed using classical methods of statistical physics. Fundamental processes at the surface of the collapsing foam are found. In particular, size is not a relevant parameter for exploding bubbles. We report acoustic experiments on foam systems. We have recorded the sound emitted by crackling cells during the collapsing of foams. The sound pattern is then analyzed using classical methods of statistical physics. Fundamental processes at the surface of the collapsing foam are found. In particular, size is not a relevant parameter for exploding bubbles. △ Less

Submitted 20 January, 2000; originally announced January 2000.

Comments: 8 pages, 4 figures, submitted for publication

Non-gaussian electrical fluctuations in a quasi-2d packing of metallic beads

Authors: N. Vandewalle, C. Lenaerts, S. Dorbolo

Abstract: The electrical properties of a two-dimensional packing of metallic beads are studied. Small mechanical perturbations of the packing leads to giant electrical fluctuations. Fluctuations are found to be non-gaussian and seem to belong to Levy stable distributions. Anticorrelations have been also found for the sign of these fluctuations. The electrical properties of a two-dimensional packing of metallic beads are studied. Small mechanical perturbations of the packing leads to giant electrical fluctuations. Fluctuations are found to be non-gaussian and seem to belong to Levy stable distributions. Anticorrelations have been also found for the sign of these fluctuations. △ Less

Submitted 20 January, 2000; originally announced January 2000.

Comments: 6 pages, 5 figures