-
On-ground calibration of the X-ray, gamma-ray, and relativistic electron detector onboard TARANIS
Authors:
Yuuki Wada,
Philippe Laurent,
Damien Pailot,
Ion Cojocari,
Eric Bréelle,
Stéphane Colonges,
Jean-Pierre Baronick,
François Lebrun,
Pierre-Louis Blelly,
David Sarria,
Kazuhiro Nakazawa,
Miles Lindsey Clark
Abstract:
We developed the X-ray, Gamma-ray and Relativistic Electron detector (XGRE) onboard the TARANIS satellite, to investigate high-energy phenomena associated with lightning discharges such as terrestrial gamma-ray flashes and terrestrial electron beams. XGRE consisted of three sensors. Each sensor has one layer of LaBr$_{3}$ crystals for X-ray/gamma-ray detections, and two layers of plastic scintilla…
▽ More
We developed the X-ray, Gamma-ray and Relativistic Electron detector (XGRE) onboard the TARANIS satellite, to investigate high-energy phenomena associated with lightning discharges such as terrestrial gamma-ray flashes and terrestrial electron beams. XGRE consisted of three sensors. Each sensor has one layer of LaBr$_{3}$ crystals for X-ray/gamma-ray detections, and two layers of plastic scintillators for electron and charged-particle discrimination. Since 2018, the flight model of XGRE was developed, and validation and calibration tests, such as a thermal cycle test and a calibration test with the sensors onboard the satellite were performed before the launch of TARANIS on 17 November 2020. The energy range of the LaBr$_{3}$ crystals sensitive to X-rays and gamma rays was determined to be 0.04-11.6 MeV, 0.08-11.0 MeV, and 0.08-11.3 MeV for XGRE1, 2, and 3, respectively. The energy resolution at 0.662 MeV (full width at half maximum) was to be 20.5%, 25.9%, and 28.6%, respectively. Results from the calibration test were then used to validate a simulation model of XGRE and TARANIS. By performing Monte Carlo simulations with the verified model, we calculated effective areas of XGRE to X-rays, gamma rays, electrons, and detector responses to incident photons and electrons coming from various elevation and azimuth angles.
△ Less
Submitted 8 May, 2024;
originally announced May 2024.
-
The Power Board of the KM3NeT Digital Optical Module: design, upgrade, and production
Authors:
S. Aiello,
A. Albert,
S. Alves Garre,
Z. Aly,
A. Ambrosone,
F. Ameli,
M. Andre,
E. Androutsou,
M. Anguita,
L. Aphecetche,
M. Ardid,
S. Ardid,
H. Atmani,
J. Aublin,
F. Badaracco,
L. Bailly-Salins,
Z. Bardacova,
B. Baret,
A. Bariego Quintana,
S. Basegmez du Pree,
Y. Becherini,
M. Bendahman,
F. Benfenati,
M. Benhassi,
D. M. Benoit
, et al. (259 additional authors not shown)
Abstract:
The KM3NeT Collaboration is building an underwater neutrino observatory at the bottom of the Mediterranean Sea consisting of two neutrino telescopes, both composed of a three-dimensional array of light detectors, known as digital optical modules. Each digital optical module contains a set of 31 three inch photomultiplier tubes distributed over the surface of a 0.44 m diameter pressure-resistant gl…
▽ More
The KM3NeT Collaboration is building an underwater neutrino observatory at the bottom of the Mediterranean Sea consisting of two neutrino telescopes, both composed of a three-dimensional array of light detectors, known as digital optical modules. Each digital optical module contains a set of 31 three inch photomultiplier tubes distributed over the surface of a 0.44 m diameter pressure-resistant glass sphere. The module includes also calibration instruments and electronics for power, readout and data acquisition. The power board was developed to supply power to all the elements of the digital optical module. The design of the power board began in 2013, and several prototypes were produced and tested. After an exhaustive validation process in various laboratories within the KM3NeT Collaboration, a mass production batch began, resulting in the construction of over 1200 power boards so far. These boards were integrated in the digital optical modules that have already been produced and deployed, 828 until October 2023. In 2017, an upgrade of the power board, to increase reliability and efficiency, was initiated. After the validation of a pre-production series, a production batch of 800 upgraded boards is currently underway. This paper describes the design, architecture, upgrade, validation, and production of the power board, including the reliability studies and tests conducted to ensure the safe operation at the bottom of the Mediterranean Sea throughout the observatory's lifespan
△ Less
Submitted 24 November, 2023;
originally announced November 2023.
-
The Athena X-ray Integral Field Unit: a consolidated design for the system requirement review of the preliminary definition phase
Authors:
Didier Barret,
Vincent Albouys,
Jan-Willem den Herder,
Luigi Piro,
Massimo Cappi,
Juhani Huovelin,
Richard Kelley,
J. Miguel Mas-Hesse,
Stéphane Paltani,
Gregor Rauw,
Agata Rozanska,
Jiri Svoboda,
Joern Wilms,
Noriko Yamasaki,
Marc Audard,
Simon Bandler,
Marco Barbera,
Xavier Barcons,
Enrico Bozzo,
Maria Teresa Ceballos,
Ivan Charles,
Elisa Costantini,
Thomas Dauser,
Anne Decourchelle,
Lionel Duband
, et al. (274 additional authors not shown)
Abstract:
The Athena X-ray Integral Unit (X-IFU) is the high resolution X-ray spectrometer, studied since 2015 for flying in the mid-30s on the Athena space X-ray Observatory, a versatile observatory designed to address the Hot and Energetic Universe science theme, selected in November 2013 by the Survey Science Committee. Based on a large format array of Transition Edge Sensors (TES), it aims to provide sp…
▽ More
The Athena X-ray Integral Unit (X-IFU) is the high resolution X-ray spectrometer, studied since 2015 for flying in the mid-30s on the Athena space X-ray Observatory, a versatile observatory designed to address the Hot and Energetic Universe science theme, selected in November 2013 by the Survey Science Committee. Based on a large format array of Transition Edge Sensors (TES), it aims to provide spatially resolved X-ray spectroscopy, with a spectral resolution of 2.5 eV (up to 7 keV) over an hexagonal field of view of 5 arc minutes (equivalent diameter). The X-IFU entered its System Requirement Review (SRR) in June 2022, at about the same time when ESA called for an overall X-IFU redesign (including the X-IFU cryostat and the cooling chain), due to an unanticipated cost overrun of Athena. In this paper, after illustrating the breakthrough capabilities of the X-IFU, we describe the instrument as presented at its SRR, browsing through all the subsystems and associated requirements. We then show the instrument budgets, with a particular emphasis on the anticipated budgets of some of its key performance parameters. Finally we briefly discuss on the ongoing key technology demonstration activities, the calibration and the activities foreseen in the X-IFU Instrument Science Center, and touch on communication and outreach activities, the consortium organisation, and finally on the life cycle assessment of X-IFU aiming at minimising the environmental footprint, associated with the development of the instrument. Thanks to the studies conducted so far on X-IFU, it is expected that along the design-to-cost exercise requested by ESA, the X-IFU will maintain flagship capabilities in spatially resolved high resolution X-ray spectroscopy, enabling most of the original X-IFU related scientific objectives of the Athena mission to be retained. (abridged).
△ Less
Submitted 28 November, 2022; v1 submitted 30 August, 2022;
originally announced August 2022.
-
Embedded software developments in KM3NeT phase I
Authors:
V. van Beveren,
D. Real,
T. Chiarusi,
D. Calvo,
S. Mastroianni,
P. Musico,
G. Pellegrini,
P. Jansweijer,
S. Colonges,
C. Bozza,
F. Filippini,
C. Nicolau,
A. Díaz
Abstract:
The KM3NeT Collaboration has already produced more than one thousand acquisition boards, used for building two deep-sea neutrino detectors at the bottom of the Mediterranean Sea, with the aim of instrumenting a volume of several cubic kilometers with light sensors to detect the Cherenkov radiation produced in neutrino interactions. The the so-called Digital Optical Modules, house the PMTs and the…
▽ More
The KM3NeT Collaboration has already produced more than one thousand acquisition boards, used for building two deep-sea neutrino detectors at the bottom of the Mediterranean Sea, with the aim of instrumenting a volume of several cubic kilometers with light sensors to detect the Cherenkov radiation produced in neutrino interactions. The the so-called Digital Optical Modules, house the PMTs and the acquisition and control electronics of the module, the Central Logic Board, which includes a Xilinx FPGA and embedded soft processor. The present work presents the architecture and functionalities of the software embedded in the soft processor of the Central Logic Board.
△ Less
Submitted 13 October, 2021; v1 submitted 3 August, 2021;
originally announced August 2021.
-
The Calibration Units of KM3NeT
Authors:
R. Le Breton,
M. Billault,
C. Boutonnet,
C. Champion,
S. Colonges,
A. Cosquer,
A. Creusot,
S. Henry,
A. Ilioni,
P. Keller,
P. Lagier,
R. Lahmann,
P. Lamare,
J. Lesrel,
M. Lindsey Clark,
J. Royon,
G. Riccobene,
D. Samtleben,
V. Van Elewyck
Abstract:
KM3NeT is a deep-sea infrastructure composed of two neutrino telescopes being deployed in the Mediterranean Sea: ARCA, near Sicily in Italy, designed for neutrino astronomy, and ORCA, near Toulon in France, designed for neutrino oscillation physics. To achieve the best performance, the exact location of the optical modules, affected by sea current, must be known at any time and the timing resoluti…
▽ More
KM3NeT is a deep-sea infrastructure composed of two neutrino telescopes being deployed in the Mediterranean Sea: ARCA, near Sicily in Italy, designed for neutrino astronomy, and ORCA, near Toulon in France, designed for neutrino oscillation physics. To achieve the best performance, the exact location of the optical modules, affected by sea current, must be known at any time and the timing resolution between optical modules must reach the nanosecond. Moreover, the properties of the environment in which the telescopes are deployed must be continuously monitored because they affect the timing and positioning calibration. KM3NeT is going to deploy several dedicated Calibration Units to meet these calibration goals. Because of the difference in size between ARCA and ORCA, the design of the Calibration Unit is not the same for the two sites. This proceeding describes all the devices, features and purposes of the Calibration Units with a focus on the ORCA Calibration Unit.
△ Less
Submitted 11 August, 2021; v1 submitted 28 July, 2021;
originally announced July 2021.
-
Deep-sea deployment of the KM3NeT neutrino telescope detection units by self-unrolling
Authors:
The KM3NeT Collaboration,
S. Aiello,
A. Albert,
S. Alves Garre,
Z. Aly,
F. Ameli,
E. G. Anassontzis,
M. Andre,
G. Androulakis,
M. Anghinolfi,
M. Anguita,
G. Anton,
M. Ardid,
J. Aublin,
C. Bagatelas,
R. Bakker,
G. Barbarino,
B. Baret,
S. Basegmez du Pree,
M. Bendahman,
E. Berbeen,
A. M. van den Berg,
V. Bertin,
S. Biagi,
M. Billault
, et al. (230 additional authors not shown)
Abstract:
KM3NeT is a research infrastructure being installed in the deep Mediterranean Sea. It will house a neutrino telescope comprising hundreds of networked moorings - detection units or strings equipped with optical instrumentation to detect the Cherenkov radiation generated by charged particles from neutrino-induced collisions in its vicinity. In comparison to moorings typically used for oceanography,…
▽ More
KM3NeT is a research infrastructure being installed in the deep Mediterranean Sea. It will house a neutrino telescope comprising hundreds of networked moorings - detection units or strings equipped with optical instrumentation to detect the Cherenkov radiation generated by charged particles from neutrino-induced collisions in its vicinity. In comparison to moorings typically used for oceanography, several key features of the KM3NeT string are different: the instrumentation is contained in transparent and thus unprotected glass spheres; two thin Dyneema ropes are used as strength members; and a thin delicate backbone tube with fibre-optics and copper wires for data and power transmission, respectively, runs along the full length of the mooring. Also, compared to other neutrino telescopes such as ANTARES in the Mediterranean Sea and GVD in Lake Baikal, the KM3NeT strings are more slender to minimise the amount of material used for support of the optical sensors. Moreover, the rate of deploying a large number of strings in a period of a few years is unprecedented. For all these reasons, for the installation of the KM3NeT strings, a custom-made, fast deployment method was designed. Despite the length of several hundreds of metres, the slim design of the string allows it to be compacted into a small, re-usable spherical launching vehicle instead of deploying the mooring weight down from a surface vessel. After being lowered to the seafloor, the string unfurls to its full length with the buoyant launching vehicle rolling along the two ropes.The design of the vehicle, the loading with a string, and its underwater self-unrolling are detailed in this paper.
△ Less
Submitted 31 July, 2020;
originally announced July 2020.
-
KM3NeT front-end and readout electronics system: hardware, firmware and software
Authors:
The KM3NeT Collaboration,
S. Aiello,
F. Ameli,
M. Andre,
G. Androulakis,
M. Anghinolfi,
G. Anton,
M. Ardid,
J. Aublin,
C. Bagatelas,
G. Barbarino,
B. Baret,
S. Basegmez du Pree,
A. Belias,
E. Berbee,
A. M. van den Berg,
V. Bertin,
V. van Beveren,
S. Biagi,
A. Biagioni,
S. Bianucci,
M. Billault,
M. Bissinger,
P. Bos,
J. Boumaaza
, et al. (215 additional authors not shown)
Abstract:
The KM3NeT research infrastructure being built at the bottom of the Mediterranean Sea will host water-Cherenkov telescopes for the detection of cosmic neutrinos. The neutrino telescopes will consist of large volume three-dimensional grids of optical modules to detect the Cherenkov light from charged particles produced by neutrino-induced interactions. Each optical module houses 31 3-inch photomult…
▽ More
The KM3NeT research infrastructure being built at the bottom of the Mediterranean Sea will host water-Cherenkov telescopes for the detection of cosmic neutrinos. The neutrino telescopes will consist of large volume three-dimensional grids of optical modules to detect the Cherenkov light from charged particles produced by neutrino-induced interactions. Each optical module houses 31 3-inch photomultiplier tubes, instrumentation for calibration of the photomultiplier signal and positioning of the optical module and all associated electronics boards. By design, the total electrical power consumption of an optical module has been capped at seven watts. This paper presents an overview of the front-end and readout electronics system inside the optical module, which has been designed for a 1~ns synchronization between the clocks of all optical modules in the grid during a life time of at least 20 years.
△ Less
Submitted 29 July, 2019; v1 submitted 15 July, 2019;
originally announced July 2019.
-
Dependence of atmospheric muon flux on seawater depth measured with the first KM3NeT detection units
Authors:
KM3NeT Collaboration,
M. Ageron,
S. Aiello,
F. Ameli,
M. Andre,
G. Androulakis,
M. Anghinolfi,
G. Anton,
M. Ardid,
J. Aublin,
C. Bagatelas,
G. Barbarino,
B. Baret,
S. Basegmez du Pree,
A. Belias,
E. Berbee,
A. M. van den Berg,
V. Bertin,
V. van Beveren,
S. Biagi,
A. Biagioni,
S. Bianucci,
M. Billault,
M. Bissinger,
R. de Boer
, et al. (240 additional authors not shown)
Abstract:
KM3NeT is a research infrastructure located in the Mediterranean Sea, that will consist of two deep-sea Cherenkov neutrino detectors. With one detector (ARCA), the KM3NeT Collaboration aims at identifying and studying TeV-PeV astrophysical neutrino sources. With the other detector (ORCA), the neutrino mass ordering will be determined by studying GeV-scale atmospheric neutrino oscillations. The fir…
▽ More
KM3NeT is a research infrastructure located in the Mediterranean Sea, that will consist of two deep-sea Cherenkov neutrino detectors. With one detector (ARCA), the KM3NeT Collaboration aims at identifying and studying TeV-PeV astrophysical neutrino sources. With the other detector (ORCA), the neutrino mass ordering will be determined by studying GeV-scale atmospheric neutrino oscillations. The first KM3NeT detection units were deployed at the Italian and French sites between 2015 and 2017. In this paper, a description of the detector is presented, together with a summary of the procedures used to calibrate the detector in-situ. Finally, the measurement of the atmospheric muon flux between 2232-3386 m seawater depth is obtained.
△ Less
Submitted 4 February, 2020; v1 submitted 6 June, 2019;
originally announced June 2019.
-
TiCkS: A Flexible White-Rabbit Based Time-Stam** Board
Authors:
C. Champion,
M. Punch,
R. Oger,
S. Colonges,
Y. Moudden
Abstract:
We have developed the TiCkS board (Time and Clock Stam**) based on the White Rabbit (WR) SPEC node (Simple PCIe FMC carrier), to provide ns-precision time-stamps (TSs) of input signals (e.g., triggers from a connected device) and transmission of these TSs to a central collection point. TiCkS was developed within the specifications of the Cherenkov Telescope Array (CTA) as one of the candidate TS…
▽ More
We have developed the TiCkS board (Time and Clock Stam**) based on the White Rabbit (WR) SPEC node (Simple PCIe FMC carrier), to provide ns-precision time-stamps (TSs) of input signals (e.g., triggers from a connected device) and transmission of these TSs to a central collection point. TiCkS was developed within the specifications of the Cherenkov Telescope Array (CTA) as one of the candidate TS nodes, with a small form-factor allowing its use in any CTA camera. The essence of this development concerns the firmware in its Spartan-6 FPGA (Field-Programmable Gate Array), with the addition of: 1) a ns-precision TDC (Time-to-Digital Convertor) for the TSs; and 2) a UDP stack (User Datagram Protocol) to send TSs and auxiliary information over the WR fibre, and to receive configuration & slow control commands over the same fibre. It also provides a PPS (Pulse Per Second) and other clock signals to the connected device, from which it can receive auxiliary event-type information over an SPI link (Serial Peripheral Interface). A version of TiCkS with an FMC connector (FPGA Mezzanine Card) will be made available in the WR OpenHardware repository, so allowing the use of a mezzanine card with varied formats of input/output connectors, providing a cheap, flexible, and reliable solution for ns-precision time-stam** of trigger signals up to 400 kHz, for use in other experiments.
△ Less
Submitted 19 October, 2017;
originally announced October 2017.
-
Cherenkov Telescope Array Contributions to the 35th International Cosmic Ray Conference (ICRC2017)
Authors:
F. Acero,
B. S. Acharya,
V. Acín Portella,
C. Adams,
I. Agudo,
F. Aharonian,
I. Al Samarai,
A. Alberdi,
M. Alcubierre,
R. Alfaro,
J. Alfaro,
C. Alispach,
R. Aloisio,
R. Alves Batista,
J. -P. Amans,
E. Amato,
L. Ambrogi,
G. Ambrosi,
M. Ambrosio,
J. Anderson,
M. Anduze,
E. O. Angüner,
E. Antolini,
L. A. Antonelli,
V. Antonuccio
, et al. (1117 additional authors not shown)
Abstract:
List of contributions from the Cherenkov Telescope Array Consortium presented at the 35th International Cosmic Ray Conference, July 12-20 2017, Busan, Korea.
List of contributions from the Cherenkov Telescope Array Consortium presented at the 35th International Cosmic Ray Conference, July 12-20 2017, Busan, Korea.
△ Less
Submitted 24 October, 2017; v1 submitted 11 September, 2017;
originally announced September 2017.
-
Intrinsic limits on resolutions in muon- and electron-neutrino charged-current events in the KM3NeT/ORCA detector
Authors:
S. Adrián-Martínez,
M. Ageron,
S. Aiello,
A. Albert,
F. Ameli,
E. G. Anassontzis,
M. Andre,
G. Androulakis,
M. Anghinolfi,
G. Anton,
M. Ardid,
T. Avgitas,
G. Barbarino,
E. Barbarito,
B. Baret,
J. Barrios-Martí,
A. Belias,
E. Berbee,
A. van den Berg,
V. Bertin,
S. Beurthey,
V. van Beveren,
N. Beverini,
S. Biagi,
A. Biagioni
, et al. (228 additional authors not shown)
Abstract:
Studying atmospheric neutrino oscillations in the few-GeV range with a multimegaton detector promises to determine the neutrino mass hierarchy. This is the main science goal pursued by the future KM3NeT/ORCA water Cherenkov detector in the Mediterranean Sea. In this paper, the processes that limit the obtainable resolution in both energy and direction in charged-current neutrino events in the ORCA…
▽ More
Studying atmospheric neutrino oscillations in the few-GeV range with a multimegaton detector promises to determine the neutrino mass hierarchy. This is the main science goal pursued by the future KM3NeT/ORCA water Cherenkov detector in the Mediterranean Sea. In this paper, the processes that limit the obtainable resolution in both energy and direction in charged-current neutrino events in the ORCA detector are investigated. These processes include the composition of the hadronic fragmentation products, the subsequent particle propagation and the photon-sampling fraction of the detector. GEANT simulations of neutrino interactions in seawater produced by GENIE are used to study the effects in the 1 - 20 GeV range. It is found that fluctuations in the hadronic cascade in conjunction with the variation of the inelasticity y are most detrimental to the resolutions. The effect of limited photon sampling in the detector is of significantly less importance. These results will therefore also be applicable to similar detectors/media, such as those in ice.
△ Less
Submitted 19 May, 2017; v1 submitted 29 November, 2016;
originally announced December 2016.
-
Contributions of the Cherenkov Telescope Array (CTA) to the 6th International Symposium on High-Energy Gamma-Ray Astronomy (Gamma 2016)
Authors:
The CTA Consortium,
:,
A. Abchiche,
U. Abeysekara,
Ó. Abril,
F. Acero,
B. S. Acharya,
C. Adams,
G. Agnetta,
F. Aharonian,
A. Akhperjanian,
A. Albert,
M. Alcubierre,
J. Alfaro,
R. Alfaro,
A. J. Allafort,
R. Aloisio,
J. -P. Amans,
E. Amato,
L. Ambrogi,
G. Ambrosi,
M. Ambrosio,
J. Anderson,
M. Anduze,
E. O. Angüner
, et al. (1387 additional authors not shown)
Abstract:
List of contributions from the Cherenkov Telescope Array (CTA) Consortium presented at the 6th International Symposium on High-Energy Gamma-Ray Astronomy (Gamma 2016), July 11-15, 2016, in Heidelberg, Germany.
List of contributions from the Cherenkov Telescope Array (CTA) Consortium presented at the 6th International Symposium on High-Energy Gamma-Ray Astronomy (Gamma 2016), July 11-15, 2016, in Heidelberg, Germany.
△ Less
Submitted 17 October, 2016;
originally announced October 2016.
-
Letter of Intent for KM3NeT 2.0
Authors:
S. Adrián-Martínez,
M. Ageron,
F. Aharonian,
S. Aiello,
A. Albert,
F. Ameli,
E. Anassontzis,
M. Andre,
G. Androulakis,
M. Anghinolfi,
G. Anton,
M. Ardid,
T. Avgitas,
G. Barbarino,
E. Barbarito,
B. Baret,
J. Barrios-Martí,
B. Belhorma,
A. Belias,
E. Berbee,
A. van den Berg,
V. Bertin,
S. Beurthey,
V. van Beveren,
N. Beverini
, et al. (222 additional authors not shown)
Abstract:
The main objectives of the KM3NeT Collaboration are i) the discovery and subsequent observation of high-energy neutrino sources in the Universe and ii) the determination of the mass hierarchy of neutrinos. These objectives are strongly motivated by two recent important discoveries, namely: 1) The high-energy astrophysical neutrino signal reported by IceCube and 2) the sizable contribution of elect…
▽ More
The main objectives of the KM3NeT Collaboration are i) the discovery and subsequent observation of high-energy neutrino sources in the Universe and ii) the determination of the mass hierarchy of neutrinos. These objectives are strongly motivated by two recent important discoveries, namely: 1) The high-energy astrophysical neutrino signal reported by IceCube and 2) the sizable contribution of electron neutrinos to the third neutrino mass eigenstate as reported by Daya Bay, Reno and others. To meet these objectives, the KM3NeT Collaboration plans to build a new Research Infrastructure consisting of a network of deep-sea neutrino telescopes in the Mediterranean Sea. A phased and distributed implementation is pursued which maximises the access to regional funds, the availability of human resources and the synergetic opportunities for the earth and sea sciences community. Three suitable deep-sea sites are identified, namely off-shore Toulon (France), Capo Passero (Italy) and Pylos (Greece). The infrastructure will consist of three so-called building blocks. A building block comprises 115 strings, each string comprises 18 optical modules and each optical module comprises 31 photo-multiplier tubes. Each building block thus constitutes a 3-dimensional array of photo sensors that can be used to detect the Cherenkov light produced by relativistic particles emerging from neutrino interactions. Two building blocks will be configured to fully explore the IceCube signal with different methodology, improved resolution and complementary field of view, including the Galactic plane. One building block will be configured to precisely measure atmospheric neutrino oscillations.
△ Less
Submitted 26 July, 2016; v1 submitted 27 January, 2016;
originally announced January 2016.
-
The prototype detection unit of the KM3NeT detector
Authors:
KM3NeT Collaboration,
S. Adrián-Martínez,
M. Ageron,
F. Aharonian,
S. Aiello,
A. Albert,
F. Ameli,
E. G. Anassontzis,
G. C. Androulakis,
M. Anghinolfi,
G. Anton,
S. Anvar,
M. Ardid,
T. Avgitas,
K. Balasi,
H. Band,
G. Barbarino,
E. Barbarito,
F. Barbato,
B. Baret,
S. Baron,
J. Barrios,
A. Belias,
E. Berbee,
A. M. van den Berg
, et al. (224 additional authors not shown)
Abstract:
A prototype detection unit of the KM3NeT deep-sea neutrino telescope has been installed at 3500m depth 80km offshore the Italian coast. KM3NeT in its final configuration will contain several hundreds of detection units. Each detection unit is a mechanical structure anchored to the sea floor, held vertical by a submerged buoy and supporting optical modules for the detection of Cherenkov light emitt…
▽ More
A prototype detection unit of the KM3NeT deep-sea neutrino telescope has been installed at 3500m depth 80km offshore the Italian coast. KM3NeT in its final configuration will contain several hundreds of detection units. Each detection unit is a mechanical structure anchored to the sea floor, held vertical by a submerged buoy and supporting optical modules for the detection of Cherenkov light emitted by charged secondary particles emerging from neutrino interactions. This prototype string implements three optical modules with 31 photomultiplier tubes each. These optical modules were developed by the KM3NeT Collaboration to enhance the detection capability of neutrino interactions. The prototype detection unit was operated since its deployment in May 2014 until its decommissioning in July 2015. Reconstruction of the particle trajectories from the data requires a nanosecond accuracy in the time calibration. A procedure for relative time calibration of the photomultiplier tubes contained in each optical module is described. This procedure is based on the measured coincidences produced in the sea by the 40K background light and can easily be expanded to a detector with several thousands of optical modules. The time offsets between the different optical modules are obtained using LED nanobeacons mounted inside them. A set of data corresponding to 600 hours of livetime was analysed. The results show good agreement with Monte Carlo simulations of the expected optical background and the signal from atmospheric muons. An almost background-free sample of muons was selected by filtering the time correlated signals on all the three optical modules. The zenith angle of the selected muons was reconstructed with a precision of about 3°.
△ Less
Submitted 23 December, 2015; v1 submitted 6 October, 2015;
originally announced October 2015.
-
Status and Plans for the Array Control and Data Acquisition System of the Cherenkov Telescope Array
Authors:
I. Oya,
M. Fuessling,
U. Schwanke,
P. Wegner,
A. Balzer,
D. Berge,
J. Borkowski,
J. Camprecios,
S. Colonges,
J. Colome,
C. Champion,
V. Conforti,
F. Gianotti,
T. Le Flour,
R. Lindemann,
E. Lyard,
M. Mayer,
D. Melkumyan,
M. Punch,
C. Tanci,
T. Schmidt,
J. Schwarz,
G. Tosti,
K. Verma,
A. Weinstein
, et al. (2 additional authors not shown)
Abstract:
The Cherenkov Telescope Array (CTA) is the next-generation atmospheric Cherenkov gamma-ray observatory. CTA will consist of two installations, one in the northern, and the other in the southern hemisphere, containing tens of telescopes of different sizes. The CTA performance requirements and the inherent complexity associated with the operation, control and monitoring of such a large distributed m…
▽ More
The Cherenkov Telescope Array (CTA) is the next-generation atmospheric Cherenkov gamma-ray observatory. CTA will consist of two installations, one in the northern, and the other in the southern hemisphere, containing tens of telescopes of different sizes. The CTA performance requirements and the inherent complexity associated with the operation, control and monitoring of such a large distributed multi-telescope array leads to new challenges in the field of the gamma-ray astronomy. The ACTL (array control and data acquisition) system will consist of the hardware and software that is necessary to control and monitor the CTA arrays, as well as to time-stamp, read-out, filter and store -at aggregated rates of few GB/s- the scientific data. The ACTL system must be flexible enough to permit the simultaneous automatic operation of multiple sub-arrays of telescopes with a minimum personnel effort on site. One of the challenges of the system is to provide a reliable integration of the control of a large and heterogeneous set of devices. Moreover, the system is required to be ready to adapt the observation schedule, on timescales of a few tens of seconds, to account for changing environmental conditions or to prioritize incoming scientific alerts from time-critical transient phenomena such as gamma ray bursts. This contribution provides a summary of the main design choices and plans for building the ACTL system.
△ Less
Submitted 3 September, 2015;
originally announced September 2015.
-
NectarCAM : a camera for the medium size telescopes of the Cherenkov Telescope Array
Authors:
J-F. Glicenstein,
O. Abril,
J-A. Barrio,
O. Blanch~Bigas,
J. Bolmont,
F. Bouyjou,
P. Brun,
E. Chabanne,
C. Champion,
S. Colonges,
P. Corona,
E. Delagnes,
C. Delgado,
C. Diaz Ginzov,
D. Durand,
J-P. Ernenwein,
S. Fegan,
O. Ferreira,
M. Fesquet,
A. Fiasson,
G. Fontaine,
N. Fouque,
D. Gascon,
B. Giebels,
F. Henault
, et al. (41 additional authors not shown)
Abstract:
NectarCAM is a camera proposed for the medium-sized telescopes of the Cherenkov Telescope Array (CTA) covering the central energy range of ~100 GeV to ~30 TeV. It has a modular design and is based on the NECTAr chip, at the heart of which is a GHz sampling Switched Capacitor Array and a 12-bit Analog to Digital converter. The camera will be equipped with 265 7-photomultiplier modules, covering a f…
▽ More
NectarCAM is a camera proposed for the medium-sized telescopes of the Cherenkov Telescope Array (CTA) covering the central energy range of ~100 GeV to ~30 TeV. It has a modular design and is based on the NECTAr chip, at the heart of which is a GHz sampling Switched Capacitor Array and a 12-bit Analog to Digital converter. The camera will be equipped with 265 7-photomultiplier modules, covering a field of view of 8 degrees. Each module includes the photomultiplier bases, high voltage supply, pre-amplifier, trigger, readout and Ethernet transceiver. The recorded events last between a few nanoseconds and tens of nanoseconds. The camera trigger will be flexible so as to minimize the read-out dead-time of the NECTAr chips. NectarCAM is designed to sustain a data rate of more than 4 kHz with less than 5\% dead time. The camera concept, the design and tests of the various subcomponents and results of thermal and electrical prototypes are presented. The design includes the mechanical structure, cooling of the electronics, read-out, clock distribution, slow control, data-acquisition, triggering, monitoring and services.
△ Less
Submitted 26 August, 2015;
originally announced August 2015.
-
CTA Contributions to the 34th International Cosmic Ray Conference (ICRC2015)
Authors:
The CTA Consortium,
:,
A. Abchiche,
U. Abeysekara,
Ó. Abril,
F. Acero,
B. S. Acharya,
M. Actis,
G. Agnetta,
J. A. Aguilar,
F. Aharonian,
A. Akhperjanian,
A. Albert,
M. Alcubierre,
R. Alfaro,
E. Aliu,
A. J. Allafort,
D. Allan,
I. Allekotte,
R. Aloisio,
J. -P. Amans,
E. Amato,
L. Ambrogi,
G. Ambrosi,
M. Ambrosio
, et al. (1290 additional authors not shown)
Abstract:
List of contributions from the CTA Consortium presented at the 34th International Cosmic Ray Conference, 30 July - 6 August 2015, The Hague, The Netherlands.
List of contributions from the CTA Consortium presented at the 34th International Cosmic Ray Conference, 30 July - 6 August 2015, The Hague, The Netherlands.
△ Less
Submitted 11 September, 2015; v1 submitted 24 August, 2015;
originally announced August 2015.
-
Deep sea tests of a prototype of the KM3NeT digital optical module
Authors:
S. Adrián-Martínez,
M. Ageron,
F. Aharonian,
S. Aiello,
A. Albert,
F. Ameli,
E. G. Anassontzis,
M. Anghinolfi,
G. Anton,
S. Anvar,
M. Ardid,
R. de Asmundis,
K. Balasi,
H. Band,
G. Barbarino,
E. Barbarito,
F. Barbato,
B. Baret,
S. Baron,
A. Belias,
E. Berbee,
A. M. van den Berg,
A. Berkien,
V. Bertin,
S. Beurthey
, et al. (225 additional authors not shown)
Abstract:
The first prototype of a photo-detection unit of the future KM3NeT neutrino telescope has been deployed in the deep waters of the Mediterranean Sea. This digital optical module has a novel design with a very large photocathode area segmented by the use of 31 three inch photomultiplier tubes. It has been integrated in the ANTARES detector for in-situ testing and validation. This paper reports on th…
▽ More
The first prototype of a photo-detection unit of the future KM3NeT neutrino telescope has been deployed in the deep waters of the Mediterranean Sea. This digital optical module has a novel design with a very large photocathode area segmented by the use of 31 three inch photomultiplier tubes. It has been integrated in the ANTARES detector for in-situ testing and validation. This paper reports on the first months of data taking and rate measurements. The analysis results highlight the capabilities of the new module design in terms of background suppression and signal recognition. The directionality of the optical module enables the recognition of multiple Cherenkov photons from the same $^{40}$K decay and the localization bioluminescent activity in the neighbourhood. The single unit can cleanly identify atmospheric muons and provide sensitivity to the muon arrival directions.
△ Less
Submitted 16 May, 2014; v1 submitted 5 May, 2014;
originally announced May 2014.
-
The NectarCAM camera project
Authors:
J-F. Glicenstein,
M. Barcelo,
J-A. Barrio,
O. Blanch,
J. Boix,
J. Bolmont,
C. Boutonnet,
S. Cazaux,
E. Chabanne,
C. Champion,
F. Chateau,
S. Colonges,
P. Corona,
S. Couturier,
B. Courty,
E. Delagnes,
C. Delgado,
J-P. Ernenwein,
S. Fegan,
O. Ferreira,
M. Fesquet,
G. Fontaine,
N. Fouque,
F. Henault,
D. Gascón
, et al. (35 additional authors not shown)
Abstract:
In the framework of the next generation of Cherenkov telescopes, the Cherenkov Telescope Array (CTA), NectarCAM is a camera designed for the medium size telescopes covering the central energy range of 100 GeV to 30 TeV. NectarCAM will be finely pixelated (~ 1800 pixels for a 8 degree field of view, FoV) in order to image atmospheric Cherenkov showers by measuring the charge deposited within a few…
▽ More
In the framework of the next generation of Cherenkov telescopes, the Cherenkov Telescope Array (CTA), NectarCAM is a camera designed for the medium size telescopes covering the central energy range of 100 GeV to 30 TeV. NectarCAM will be finely pixelated (~ 1800 pixels for a 8 degree field of view, FoV) in order to image atmospheric Cherenkov showers by measuring the charge deposited within a few nanoseconds time-window. It will have additional features like the capacity to record the full waveform with GHz sampling for every pixel and to measure event times with nanosecond accuracy. An array of a few tens of medium size telescopes, equipped with NectarCAMs, will achieve up to a factor of ten improvement in sensitivity over existing instruments in the energy range of 100 GeV to 10 TeV. The camera is made of roughly 250 independent read-out modules, each composed of seven photo-multipliers, with their associated high voltage base and control, a read-out board and a multi-service backplane board. The read-out boards use NECTAr (New Electronics for the Cherenkov Telescope Array) ASICs which have the dual functionality of analogue memories and Analogue to Digital Converter (ADC). The camera trigger to be used will be flexible so as to minimize the read-out dead-time of the NECTAr chips. We present the camera concept and the design and tests of the various subcomponents. The design includes the mechanical parts, the cooling of the electronics, the readout, the data acquisition, the trigger, the monitoring and services.
△ Less
Submitted 17 July, 2013;
originally announced July 2013.
-
CTA contributions to the 33rd International Cosmic Ray Conference (ICRC2013)
Authors:
The CTA Consortium,
:,
O. Abril,
B. S. Acharya,
M. Actis,
G. Agnetta,
J. A. Aguilar,
F. Aharonian,
M. Ajello,
A. Akhperjanian,
M. Alcubierre,
J. Aleksic,
R. Alfaro,
E. Aliu,
A. J. Allafort,
D. Allan,
I. Allekotte,
R. Aloisio,
E. Amato,
G. Ambrosi,
M. Ambrosio,
J. Anderson,
E. O. Angüner,
L. A. Antonelli,
V. Antonuccio
, et al. (1082 additional authors not shown)
Abstract:
Compilation of CTA contributions to the proceedings of the 33rd International Cosmic Ray Conference (ICRC2013), which took place in 2-9 July, 2013, in Rio de Janeiro, Brazil
Compilation of CTA contributions to the proceedings of the 33rd International Cosmic Ray Conference (ICRC2013), which took place in 2-9 July, 2013, in Rio de Janeiro, Brazil
△ Less
Submitted 29 July, 2013; v1 submitted 8 July, 2013;
originally announced July 2013.