Showing 1–32 of 32 results for author: Cho, H J

Changes in boiling controlled by molar concentration-dependent diffusion of surfactants

Authors: Mario R. Mata, Matic Može, Armin Hadžić, Giseop Lee, Blake Naccarato, Isaac Berk, Iztok Golobič, H. Jeremy Cho

Abstract: Boiling is a prevalent phase-change process that plays a vital role in facilitating efficient heat transfer from a heating surface. While this heat transfer mechanism is generally effective, a rapid increase in surface temperature can lead to hydrodynamic instabilities, resulting in a boiling crisis. Previous studies have shown that surfactants often improve boiling performance and change the boil… ▽ More Boiling is a prevalent phase-change process that plays a vital role in facilitating efficient heat transfer from a heating surface. While this heat transfer mechanism is generally effective, a rapid increase in surface temperature can lead to hydrodynamic instabilities, resulting in a boiling crisis. Previous studies have shown that surfactants often improve boiling performance and change the boiling crisis behavior. Conventional wisdom in this field attributes that these changes in boiling behavior are tied to the critical micelle concentration (CMC) of the particular surfactant. However, our work reveals that these changes in boiling behavior are independent of the CMC for three nonionic surfactants across a wide range of molar concentrations. In addition, visual snapshots of the bubbling behavior indicate changes in bubble formation, such as bubble size and nucleation site density, influenced by the molar concentration-dependent diffusion timescale of surfactants. Hence, these findings offer compelling evidence that boiling behavior, encompassing both boiling performance and boiling crisis, is governed by the dynamic adsorption of surfactants rather than dictated by the CMC. This becomes evident when quantifying the heat transfer coefficient (HTC) and critical heat flux (CHF) using the logarithm of molar concentration, as predicted by theory. Building upon these findings, we propose insights for controlling when CHF modification occurs in specific scenarios involving any surfactants. These insights hold significant potential for optimizing heat transfer processes and leveraging surfactants in energy-related applications to maximize boiling efficiency. △ Less

Submitted 4 June, 2024; originally announced June 2024.

Comments: 21 pages, 7 figures, 2 appendices

High-yield atmospheric water capture via bioinspired material segregation

Authors: Yiwei Gao, Santiago Ricoy, Addison Cobb, Ryan Phung, Areianna Lewis, Aaron Sahm, Nathan Ortiz, Sameer Rao, H. Jeremy Cho

Abstract: Atmospheric water harvesting is urgently needed given increasing global water scarcity. Current sorbent-based devices that cycle between water capture and release have low harvesting rates. We envision a radically different multi-material architecture with segregated and simultaneous capture and release. This way, proven fast-release mechanisms that approach theoretical limits can be incorporated;… ▽ More Atmospheric water harvesting is urgently needed given increasing global water scarcity. Current sorbent-based devices that cycle between water capture and release have low harvesting rates. We envision a radically different multi-material architecture with segregated and simultaneous capture and release. This way, proven fast-release mechanisms that approach theoretical limits can be incorporated; however, no capture mechanism exists to supply liquid adequately for release. Inspired by tree frogs and airplants, our capture approach transports water through a hydrogel membrane ``skin'' into a liquid desiccant. We report an extraordinarily high capture rate of 5.50 $\text{kg}\,\text{m}^{-2}\,\text{d}^{-1}$ at a low humidity of 35%, limited by the convection of air to the device. At higher humidities, we demonstrate up to 16.9 $\text{kg}\,\text{m}^{-2}\,\text{d}^{-1}$, exceeding theoretical limits for release. Simulated performance of a hypothetical one-square-meter device shows that water could be supplied to two to three people in dry environments. This work is a significant step toward providing new resources to water-scarce regions. △ Less

Submitted 6 October, 2023; originally announced October 2023.

Comments: 22 pages, 23 figures

RECAP: Retrieval-Enhanced Context-Aware Prefix Encoder for Personalized Dialogue Response Generation

Authors: Shuai Liu, Hyundong J. Cho, Marjorie Freedman, Xuezhe Ma, Jonathan May

Abstract: Endowing chatbots with a consistent persona is essential to an engaging conversation, yet it remains an unresolved challenge. In this work, we propose a new retrieval-enhanced approach for personalized response generation. Specifically, we design a hierarchical transformer retriever trained on dialogue domain data to perform personalized retrieval and a context-aware prefix encoder that fuses the… ▽ More Endowing chatbots with a consistent persona is essential to an engaging conversation, yet it remains an unresolved challenge. In this work, we propose a new retrieval-enhanced approach for personalized response generation. Specifically, we design a hierarchical transformer retriever trained on dialogue domain data to perform personalized retrieval and a context-aware prefix encoder that fuses the retrieved information to the decoder more effectively. Extensive experiments on a real-world dataset demonstrate the effectiveness of our model at generating more fluent and personalized responses. We quantitatively evaluate our model's performance under a suite of human and automatic metrics and find it to be superior compared to state-of-the-art baselines on English Reddit conversations. △ Less

Submitted 12 June, 2023; originally announced June 2023.

Determining Optimal Combination Regimens for Patients with Multiple Myeloma

Authors: Mahya Aghaee, Urszula Ledzewicz, Michael Robbins, Natalie Bezman, Hearn Jay Cho, Helen Moore

Abstract: While many novel therapies have been approved in recent years for treating patients with multiple myeloma, there is still no established curative regimen, especially for patients with high risk disease. In this work, we use a mathematical modeling approach to determine combination therapy regimens that maximize healthy lifespan for patients with multiple myeloma. We start with a model of ordinary… ▽ More While many novel therapies have been approved in recent years for treating patients with multiple myeloma, there is still no established curative regimen, especially for patients with high risk disease. In this work, we use a mathematical modeling approach to determine combination therapy regimens that maximize healthy lifespan for patients with multiple myeloma. We start with a model of ordinary differential equations for the underlying disease and immune dynamics, which was presented and analyzed previously. We add the effects of three therapies to the model: pomalidomide, dexamethasone, and elotuzumab. We consider multiple approaches to optimizing combinations of these therapies. We find that optimal control combined with approximation outperforms other methods, in that they can quickly produce a combination regimen that is clinically-feasible and near-optimal. Implications of this work can be used to optimize doses and advance the scheduling of drugs. △ Less

Submitted 16 November, 2022; originally announced November 2022.

Quantifying the trade-off between stiffness and permeability in hydrogels

Authors: Yiwei Gao, H. Jeremy Cho

Abstract: Hydrogels have a distinct combination of mechanical and water-transport behaviors. As hydrogels stiffen, they become less permeable. Here, we combine semi-dilute polymer theory with the Kozeny-Carman equation to develop a simple scaling law describing the relationship between hydraulic permeability and mechanical stiffness. We find that these properties are dictated by the polymer strand spacing,… ▽ More Hydrogels have a distinct combination of mechanical and water-transport behaviors. As hydrogels stiffen, they become less permeable. Here, we combine semi-dilute polymer theory with the Kozeny-Carman equation to develop a simple scaling law describing the relationship between hydraulic permeability and mechanical stiffness. We find that these properties are dictated by the polymer strand spacing, explained via analogy of a bowl of noodle soup. We find a remarkably close agreement between our scaling law and experimental results across four different polymer families with varied crosslinkings. △ Less

Submitted 28 September, 2022; originally announced September 2022.

Comments: This is a pre-peer-review manuscript

Scaling laws to predict humidity-induced swelling and stiffness in hydrogels

Authors: Yiwei Gao, Nicholas K. K. Chai, Negin Garakani, Sujit S. Datta, H. Jeremy Cho

Abstract: From pasta to biological tissues to contact lenses, gel and gel-like materials inherently soften as they swell with water. In dry, low-relative-humidity environments, these materials stiffen as they de-swell with water. Here, we use semi-dilute polymer theory to develop a simple power-law relationship between hydrogel elastic modulus and swelling. From this relationship, we predict hydrogel stiffn… ▽ More From pasta to biological tissues to contact lenses, gel and gel-like materials inherently soften as they swell with water. In dry, low-relative-humidity environments, these materials stiffen as they de-swell with water. Here, we use semi-dilute polymer theory to develop a simple power-law relationship between hydrogel elastic modulus and swelling. From this relationship, we predict hydrogel stiffness or swelling at arbitrary relative humidities. Our close predictions of properties of hydrogels across three different polymer mesh families at varying crosslinking densities and relative humidities demonstrate the validity and generality of our understanding. This predictive capability enables more rapid material discovery and selection for hydrogel applications in varying humidity environments. △ Less

Submitted 27 September, 2021; originally announced September 2021.

Comments: This is a pre-peer-review manuscript

Anisotropic heat conduction of coherently transported phonons in InGaO3(ZnO)m single crystal films with superlattice structures

Authors: Hai Jun Cho, Yuzhang Wu, Youngha Kwon, Jiajun Qi, Yuna Kim, Keiji Saito, Hiromichi Ohta

Abstract: Superlattices provide a great platform for studying coherent transportation of low-frequency phonons, which are the main issues in mastering the manipulation of heat conduction. Studies have shown that the dominating characteristics in the thermal conductivity of superlattice can be adjusted between wave-like and particle-like phonon properties depending on the superlattice period. However, the ph… ▽ More Superlattices provide a great platform for studying coherent transportation of low-frequency phonons, which are the main issues in mastering the manipulation of heat conduction. Studies have shown that the dominating characteristics in the thermal conductivity of superlattice can be adjusted between wave-like and particle-like phonon properties depending on the superlattice period. However, the phonon coherence length and the phonon mean free path from Umklapp processes have not been defined in one superlattice system, and the transition from wave-like and particle-like behavior is not clear to date despite the extensive research efforts. In this study, we use InGaO3(ZnO)m (m = integer) single crystal films with superlattice structure to experimentally characterize the phonon coherence length as well as the Umklapp mean free path in one system. According to the results, the nature of heat conduction in superlattice can change in three different ways depending on the ratio between the phonon coherence length and the superlattice period. We also discuss the role of the phonon characteristic lengths in the heat conduction of superlattices and its anisotropy. △ Less

Submitted 10 August, 2021; originally announced August 2021.

Under pressure: Hydrogel swelling in a granular medium

Authors: Jean-François Louf, Nancy B. Lu, Margaret G. O'Connell, H. Jeremy Cho, Sujit S. Datta

Abstract: Hydrogels hold promise in agriculture as reservoirs of water in dry soil, potentially alleviating the burden of irrigation. However, confinement in soil can markedly reduce the ability of hydrogels to absorb water and swell, limiting their widespread adoption. Unfortunately, the underlying reason remains unknown. By directly visualizing the swelling of hydrogels confined in three-dimensional granu… ▽ More Hydrogels hold promise in agriculture as reservoirs of water in dry soil, potentially alleviating the burden of irrigation. However, confinement in soil can markedly reduce the ability of hydrogels to absorb water and swell, limiting their widespread adoption. Unfortunately, the underlying reason remains unknown. By directly visualizing the swelling of hydrogels confined in three-dimensional granular media, we demonstrate that the extent of hydrogel swelling is determined by the competition between the force exerted by the hydrogel due to osmotic swelling and the confining force transmitted by the surrounding grains. Furthermore, the medium can itself be restructured by hydrogel swelling, as set by the balance between the osmotic swelling force, the confining force, and intergrain friction. Together, our results provide quantitative principles to predict how hydrogels behave in confinement, potentially improving their use in agriculture as well as informing other applications such as oil recovery, construction, mechanobiology, and filtration. △ Less

Submitted 21 March, 2021; originally announced March 2021.

Comments: This article is published in Science Advances and supplementary material is available at https://advances.sciencemag.org/content/7/7/eabd2711

Journal ref: Science Advances, Vol. 7, no. 7, eabd2711 (2021)

Towards Automated Safety Coverage and Testing for Autonomous Vehicles with Reinforcement Learning

Authors: Hyun Jae Cho, Madhur Behl

Abstract: The kind of closed-loop verification likely to be required for autonomous vehicle (AV) safety testing is beyond the reach of traditional test methodologies and discrete verification. Validation puts the autonomous vehicle system to the test in scenarios or situations that the system would likely encounter in everyday driving after its release. These scenarios can either be controlled directly in a… ▽ More The kind of closed-loop verification likely to be required for autonomous vehicle (AV) safety testing is beyond the reach of traditional test methodologies and discrete verification. Validation puts the autonomous vehicle system to the test in scenarios or situations that the system would likely encounter in everyday driving after its release. These scenarios can either be controlled directly in a physical (closed-course proving ground) or virtual (simulation of predefined scenarios) environment, or they can arise spontaneously during operation in the real world (open-road testing or simulation of randomly generated scenarios). In AV testing, simulation serves primarily two purposes: to assist the development of a robust autonomous vehicle and to test and validate the AV before release. A challenge arises from the sheer number of scenario variations that can be constructed from each of the above sources due to the high number of variables involved (most of which are continuous). Even with continuous variables discretized, the possible number of combinations becomes practically infeasible to test. To overcome this challenge we propose using reinforcement learning (RL) to generate failure examples and unexpected traffic situations for the AV software implementation. Although reinforcement learning algorithms have achieved notable results in games and some robotic manipulations, this technique has not been widely scaled up to the more challenging real world applications like autonomous driving. △ Less

Submitted 22 May, 2020; originally announced May 2020.

Electric field thermopower modulation analyses of the operation mechanism of transparent amorphous SnO$_2$ thin-film transistor

Authors: Dou-dou Liang, Yu-qiao Zhang, Hai Jun Cho, Hiromichi Ohta

Abstract: Transparent amorphous oxide semiconductors (TAOSs) based transparent thin-film transistors (TTFTs) with high field effect mobility are essential for develo** advanced flat panel displays. Among TAOSs, amorphous (a-) SnO$_2$ has several advantages against current a-InGaZnO4 such as higher field effect mobility and being indium free. Although a-SnO$_2$ TTFT has been demonstrated several times, the… ▽ More Transparent amorphous oxide semiconductors (TAOSs) based transparent thin-film transistors (TTFTs) with high field effect mobility are essential for develo** advanced flat panel displays. Among TAOSs, amorphous (a-) SnO$_2$ has several advantages against current a-InGaZnO4 such as higher field effect mobility and being indium free. Although a-SnO$_2$ TTFT has been demonstrated several times, the operation mechanism has not been clarified thus far due to the strong gas sensing characteristics of SnO$_2$. Here we clarify the operation mechanism of a-SnO$_2$ TTFT by electric field thermopower modulation analyses. We prepared a bottom-gate top-contact type TTFT using 4.2-nm-thick a-SnO$_2$ as the channel without any surface passivation. The effective thickness of the conducting channel was ~1.7 + - 0.4 nm in air and in vacuum, but a large threshold gate voltage shift occurred in different atmospheres; this is attributed to carrier depletion near at the top surface (~2.5 nm) of the a-SnO$_2$ due to its interaction with the gas molecules and the resulting shift in the Fermi energy. The present results would provide a fundamental design concept to develop a-SnO$_2$ TTFT. △ Less

Submitted 23 March, 2020; originally announced March 2020.

Journal ref: Applied Physics Letters 116, 143503 (2020)

Effect of lattice distortions on the electron and thermal transport properties of transparent oxide semiconductor Ba1-xSrxSnO3 solid solution films

Authors: Hai Jun Cho, Koichi Sato, Mian Wei, Gowoon Kim, Hiromichi Ohta

Abstract: La-doped ASnO3 (A = Ba, Sr) have great potential as advanced transparent oxide semiconductors due to their large optical bandgap and relatively high electron mobility. The bandgap of Ba1-xSrxSnO3 solid solution increases from 3.2 eV (BaSnO3) to 4.6 eV (SrSnO3) with x. However, the increase in the bandgap is accompanied by reductions in the electrical conductivity. The versatility in the changes in… ▽ More La-doped ASnO3 (A = Ba, Sr) have great potential as advanced transparent oxide semiconductors due to their large optical bandgap and relatively high electron mobility. The bandgap of Ba1-xSrxSnO3 solid solution increases from 3.2 eV (BaSnO3) to 4.6 eV (SrSnO3) with x. However, the increase in the bandgap is accompanied by reductions in the electrical conductivity. The versatility in the changes in the electrical properties are not trivial, and the property optimization has been challenging. Here we propose a simple metric for quantifying the transport properties of ASnO3. We investigated the electron/thermal transport properties of Ba1-xSrxSnO3 solid solution films and their relationship with the lattice distortion. The results suggest that the all transport properties of Ba1-xSrxSnO3 are dominated by the lattice distortion. This phenomenon is attributed to the distortions in the SnO6 octahedron, which consists the conduction band. △ Less

Submitted 26 February, 2020; originally announced February 2020.

Journal ref: J. Appl. Phys. 127, 115701 (2020)

High electrical conducting deep-ultraviolet-transparent oxide semiconductor La-doped SrSnO3 exceeding ~3000 S cm-1

Authors: Mian Wei, Anup V. Sanchela, Bin Feng, Yuichi Ikuhara, Hai Jun Cho, Hiromichi Ohta

Abstract: La-doped SrSnO3 (LSSO) is known as one of deep-ultraviolet (DUV)-transparent conducting oxides with an energy bandgap of ~4.6 eV. Since LSSO can be grown heteroepitaxially on more wide bandgap substrates such as MgO (Eg ~7.8 eV), LSSO is considered to be a good candidate as a DUV-transparent electrode. However, the electrical conductivity of LSSO films are below 1000 S cm^-1, most likely due to th… ▽ More La-doped SrSnO3 (LSSO) is known as one of deep-ultraviolet (DUV)-transparent conducting oxides with an energy bandgap of ~4.6 eV. Since LSSO can be grown heteroepitaxially on more wide bandgap substrates such as MgO (Eg ~7.8 eV), LSSO is considered to be a good candidate as a DUV-transparent electrode. However, the electrical conductivity of LSSO films are below 1000 S cm^-1, most likely due to the low solubility of La ion in the LSSO lattice. Here we report that high electrically conducting (>3000 S cm^-1) LSSO thin films with an energy bandgap of ~4.6 eV can be fabricated by pulsed laser deposition on MgO substrate followed by a simple annealing in vacuum. From the X-ray diffraction and the scanning transmission electron microscopy analyses, we found that lateral grain growth occurred during the annealing, which improved the activation rate of La ion, leading to a significant improvement of carrier concentration (3.26 x 10^20 cm^-3) and Hall mobility (55.8 cm^2 V^-1 s^-1). The present DUV-transparent oxide semiconductor would be useful as a transparent electrode for develo** optoelectronic devices, which transmit and/or emit DUV-light. △ Less

Submitted 20 November, 2019; originally announced November 2019.

Comments: 19 pages, 7 figures

Macroscopic visualization of fast electrochemical reaction of SrCoOx oxygen sponge

Authors: Qian Yang, Hai Jun Cho, Hyoungjeen Jeen, Hiromichi Ohta

Abstract: Strontium cobaltite (SrCoOx) is known as a material showing fast topotactic electrochemical Redox reaction so-called oxygen sponge. Although atomic scale phenomenon of the oxidation of SrCoO2.5 into SrCoO3 is known, the macroscopic phenomenon has not been clarified yet thus far. Here, we visualize the electrochemical oxidation of SrCoOx macroscopically. SrCoOx epitaxial films with various oxidatio… ▽ More Strontium cobaltite (SrCoOx) is known as a material showing fast topotactic electrochemical Redox reaction so-called oxygen sponge. Although atomic scale phenomenon of the oxidation of SrCoO2.5 into SrCoO3 is known, the macroscopic phenomenon has not been clarified yet thus far. Here, we visualize the electrochemical oxidation of SrCoOx macroscopically. SrCoOx epitaxial films with various oxidation states were prepared by the electrochemical oxidation of SrCoO2.5 film into SrCoO3-d film. Steep decrease of both resistivity and the absolute value of thermopower of electrochemically oxidized SrCoOx epitaxial films indicated the columnar oxidation firstly occurred along with the surface normal and then spread in the perpendicular to the normal. Further, we directly visualized the phenomena using the conductive AFM. This macroscopic image of the electrochemical oxidation would be useful to develop a functional device utilizing the electrochemical redox reaction of SrCoOx. △ Less

Submitted 24 October, 2019; originally announced October 2019.

Comments: 24 pages, 5 figures, 5 supplementary figures

Journal ref: published in 2019

Scaling Law for Cracking in Shrinkable Granular Packings

Authors: H. Jeremy Cho, Sujit S. Datta

Abstract: Hydrated granular packings often crack into discrete clusters of grains when dried. Despite its ubiquity, accurate prediction of cracking remains elusive. Here, we elucidate the previously overlooked role of individual grain shrinkage---a feature common to many materials---in determining crack patterning using both experiments and simulations. By extending the classical Griffith crack theory, we o… ▽ More Hydrated granular packings often crack into discrete clusters of grains when dried. Despite its ubiquity, accurate prediction of cracking remains elusive. Here, we elucidate the previously overlooked role of individual grain shrinkage---a feature common to many materials---in determining crack patterning using both experiments and simulations. By extending the classical Griffith crack theory, we obtain a scaling law that quantifies how cluster size depends on the interplay between grain shrinkage, stiffness, and size---applicable to a diverse array of shrinkable, granular packings. △ Less

Submitted 4 October, 2019; originally announced October 2019.

Journal ref: Physical Review Letters 123, 158004 (2019)

Crack formation and self-closing in shrinkable, granular packings

Authors: H. Jeremy Cho, Nancy B. Lu, Michael P. Howard, Rebekah A. Adams, Sujit S. Datta

Abstract: Many clays, soils, biological tissues, foods, and coatings are shrinkable, granular materials: they are composed of packed, hydrated grains that shrink when dried. In many cases, these packings crack during drying, critically hindering applications. However, while cracking has been widely studied for bulk gels and packings of non-shrinkable grains, little is known about how packings of shrinkable… ▽ More Many clays, soils, biological tissues, foods, and coatings are shrinkable, granular materials: they are composed of packed, hydrated grains that shrink when dried. In many cases, these packings crack during drying, critically hindering applications. However, while cracking has been widely studied for bulk gels and packings of non-shrinkable grains, little is known about how packings of shrinkable grains crack. Here, we elucidate how grain shrinkage alters cracking during drying. Using experiments with model shrinkable hydrogel beads, we show that differential shrinkage can dramatically alter crack evolution during drying---in some cases, even causing cracks to spontaneously "self-close". In other cases, packings shrink without cracking or crack irreversibly. We developed both granular and continuum models to quantify the interplay between grain shrinkage, poromechanics, packing size, drying rate, capillarity, and substrate friction on cracking. Guided by the theory, we also found that cracking can be completely altered by varying the spatial profile of drying. Our work elucidates the rich physics underlying cracking in shrinkable, granular packings, and yields new strategies for controlling crack evolution. △ Less

Submitted 15 May, 2019; originally announced May 2019.

Comments: In press

Journal ref: Soft Matter 15, 4689-4702 (2019)

Oxygen vacancy driven mobility enhancement in epitaxial La-doped BaSnO3 from vacuum annealing

Authors: Hai Jun Cho, Takaki Onozato, Mian Wei, Anup V. Sanchela, Hiromichi Ohta

Abstract: Wide bandgap (~3.1 eV) La-doped BaSnO3 (LBSO) has attracted increasing attention as one of the transparent oxide semiconductors since its bulk single crystal shows a high carrier mobility (~320 cm2 V-1 s-1) with a high carrier concentration (~10^20 cm-3). For this reason, many researchers have fabricated LBSO epitaxial films thus far, but the obtainable carrier mobility is substantially low compar… ▽ More Wide bandgap (~3.1 eV) La-doped BaSnO3 (LBSO) has attracted increasing attention as one of the transparent oxide semiconductors since its bulk single crystal shows a high carrier mobility (~320 cm2 V-1 s-1) with a high carrier concentration (~10^20 cm-3). For this reason, many researchers have fabricated LBSO epitaxial films thus far, but the obtainable carrier mobility is substantially low compared to that of single crystals due to the formation of the lattice/structural defects. Here we report that the mobility suppression in LBSO films can be lifted by a simple vacuum annealing process. The vacuum annealing of the LBSO films on MgO substrate increased the carrier concentrations due to the oxygen vacancy formation, which leads to simultaneous lateral grain growth. As a result, the carrier mobility was greatly improved by the vacuum annealing, which does not occur after heat treatment in air. These results expand our current knowledge on the point defect formation in epitaxial LBSO films and show that vacuum annealing is a powerful tool for enhancing the mobility values of LBSO films. △ Less

Submitted 30 August, 2018; originally announced August 2018.

Journal ref: APL Materials 7, 022507 (2019)

Buffer layer-less fabrication of high-mobility transparent oxide semiconductor, La-doped BaSnO3

Authors: Anup V. Sanchela, Mian Wei, Joonhyuk Lee, Gowoon Kim, Hyoungjeen Jeen, Bin Feng, Yuichi Ikuhara, Hai Jun Cho, Hiromichi Ohta

Abstract: Transparent oxide semiconductors (TOSs) showing both high visible transparency and high electron mobility have attracted great attention towards the realization of advanced optoelectronic devices. La-doped BaSnO3 (LBSO) is one of the most promising TOSs because its single crystal exhibits a high electron mobility. However, in the LBSO films, it is very hard to obtain high mobility due to the threa… ▽ More Transparent oxide semiconductors (TOSs) showing both high visible transparency and high electron mobility have attracted great attention towards the realization of advanced optoelectronic devices. La-doped BaSnO3 (LBSO) is one of the most promising TOSs because its single crystal exhibits a high electron mobility. However, in the LBSO films, it is very hard to obtain high mobility due to the threading dislocations, which are originated from the lattice mismatch between the film and the substrate. Therefore, many researchers have tried to improve the mobility by inserting a buffer layer. While the buffer layers increased the electron mobilities, this approach leaves much to be desired since it involves a two-step film fabrication process and the enhanced mobility values are still significantly lower than single crystal values. We show herein that the electron mobility of LBSO films can be improved without inserting any buffer layers if the films are grown under highly oxidative ozone (O3) atmospheres. The O3 environments relaxed the LBSO lattice and reduced the formation of Sn2+ states, which are known to suppress the electron mobility in LBSO. The resultant O3-LBSO films showed improved mobility values up to 115 cm2 V-1 s-1, which is among the highest in LBSO films on SrTiO3 substrates and comparable to LBSO films with buffer layers. △ Less

Submitted 22 August, 2018; originally announced August 2018.

Comments: 16 pages including 5 figures

Journal ref: J. Mater. Chem. C, 2019, 7, 5797

The Minkowski dimension of boundary singular points in the Navier--Stokes equations

Authors: Hi Jun Choe, Minsuk Yang

Abstract: We study the partial regularity problem of the three-dimensional incompressible Navier--Stokes equations. We present a new boundary regularity criterion for boundary suitable weak solutions. As an application, a bound for the parabolic Minkowski dimension of possible singular points on the boundary is obtained. We study the partial regularity problem of the three-dimensional incompressible Navier--Stokes equations. We present a new boundary regularity criterion for boundary suitable weak solutions. As an application, a bound for the parabolic Minkowski dimension of possible singular points on the boundary is obtained. △ Less

Submitted 11 November, 2018; v1 submitted 12 May, 2018; originally announced May 2018.

Comments: 16 pages

Blow up criteria for the compressible Navier--Stokes equations

Authors: Hi Jun Choe, Minsuk Yang

Abstract: We study the strong solution to the 3-D compressible Navier--Stokes equations. We propose a new blow up criterion for barotropic gases in terms of the integral norm of density $ρ$ and the divergence of the velocity $\bu$ without any restriction on the physical viscosity constants. Our blow up criteria can be seen as a partial realization of the underlying principle that the higher integrability im… ▽ More We study the strong solution to the 3-D compressible Navier--Stokes equations. We propose a new blow up criterion for barotropic gases in terms of the integral norm of density $ρ$ and the divergence of the velocity $\bu$ without any restriction on the physical viscosity constants. Our blow up criteria can be seen as a partial realization of the underlying principle that the higher integrability implies the boundedness and then eventual regularity. We also present similar blow up criterion for the heat conducting gases. △ Less

Submitted 15 May, 2017; originally announced May 2017.

Local kinetic energy and singularities of the incompressible Navier--Stokes Equations

Authors: Hi Jun Choe, Minsuk Yang

Abstract: We study the partial regularity problem of the incompressible Navier--Stokes equations. In this paper, we show that a reverse Hölder inequality of velocity gradient with increasing support holds under the condition that a scaled functional corresponding the local kinetic energy is uniformly bounded. As an application, we give a new bound for the Hausdorff dimension and the Minkowski dimension of s… ▽ More We study the partial regularity problem of the incompressible Navier--Stokes equations. In this paper, we show that a reverse Hölder inequality of velocity gradient with increasing support holds under the condition that a scaled functional corresponding the local kinetic energy is uniformly bounded. As an application, we give a new bound for the Hausdorff dimension and the Minkowski dimension of singular set when weak solutions $v$ belong to $L^\infty(0,T;L^{3,w}(\mathbb{R}^3))$ where $L^{3,w}(\mathbb{R}^3)$ denotes the standard weak Lebesgue space. △ Less

Submitted 12 May, 2017; originally announced May 2017.

On regularity and singularity for $L^\infty(0,T;L^{3,w}(\mathbb{R}^3))$ solutions to the Navier-Stokes equations

Authors: Hi Jun Choe, Jörg Wolf, Minsuk Yang

Abstract: We study local regularity properties of a weak solution $u$ to the Cauchy problem of the incompressible Navier-Stokes equations. We present a new regularity criterion for the weak solution $u$ satisfying the condition $L^\infty(0,T;L^{3,w}(\mathbb{R}^3))$ without any smallness assumption on that scale, where $L^{3,w}(\mathbb{R}^3)$ denotes the standard weak Lebesgue space. As an application, we co… ▽ More We study local regularity properties of a weak solution $u$ to the Cauchy problem of the incompressible Navier-Stokes equations. We present a new regularity criterion for the weak solution $u$ satisfying the condition $L^\infty(0,T;L^{3,w}(\mathbb{R}^3))$ without any smallness assumption on that scale, where $L^{3,w}(\mathbb{R}^3)$ denotes the standard weak Lebesgue space. As an application, we conclude that there are at most a finite number of blowup points at any singular time $t$. The condition that the weak Lebesgue space norm of the veclocity field $u$ is bounded in time is encompassing type I singularity and significantly weaker than the end point case of the so-called Ladyzhenskaya-Prodi-Serrin condition proved by Escauriaza-Sergin-Šverák. △ Less

Submitted 15 November, 2016; originally announced November 2016.

A new local regularity criterion for suitable weak solutions of the Navier--Stokes equations in terms of the velocity gradient

Authors: Hi Jun Choe, Joerg Wolf, Minsuk Yang

Abstract: We study the partial regularity of suitable weak solutions to the three dimensional incompressible Navier--Stokes equations. There have been several attempts to refine the Caffarelli--Kohn--Nirenberg criterion (1982). We present an improved version of the CKN criterion with a direct method, which also provides the quantitative relation in Seregin's criterion (2007). We study the partial regularity of suitable weak solutions to the three dimensional incompressible Navier--Stokes equations. There have been several attempts to refine the Caffarelli--Kohn--Nirenberg criterion (1982). We present an improved version of the CKN criterion with a direct method, which also provides the quantitative relation in Seregin's criterion (2007). △ Less

Submitted 8 June, 2016; originally announced June 2016.

Comments: 17 pages

Recombining binomial tree for constant elasticity of variance process

Authors: Hi Jun Choe, Jeong Ho Chu, So Jeong Shin

Abstract: The theme in this paper is the recombining binomial tree to price American put option when the underlying stock follows constant elasticity of variance(CEV) process. Recombining nodes of binomial tree are decided from finite difference scheme to emulate CEV process and the tree has a linear complexity. Also it is derived from the differential equation the asymptotic envelope of the boundary of tre… ▽ More The theme in this paper is the recombining binomial tree to price American put option when the underlying stock follows constant elasticity of variance(CEV) process. Recombining nodes of binomial tree are decided from finite difference scheme to emulate CEV process and the tree has a linear complexity. Also it is derived from the differential equation the asymptotic envelope of the boundary of tree. Conducting numerical experiments, we confirm the convergence and accuracy of the pricing by our recombining binomial tree method. As a result, we can compute the price of American put option under CEV model, effectively. △ Less

Submitted 22 October, 2014; originally announced October 2014.

Comments: 17 pages, 7 figures, 1 table

Experimental and theoretical studies on visible light attenuation in water

Authors: A. Simpson, A. Ludu, H. J. Cho, H. Liu

Abstract: In this study we describe lab experiments on determining the above water reflectance Rrs coefficient, and the water attenuation coefficient Kd for fresh water. Different types of screens (totally absorbent, gray, etc.) were submerged in water (0-0.6 m) and illuminated from outside. The spectral density of the water leaving radiance was measured for different depths. The results were ran by a code… ▽ More In this study we describe lab experiments on determining the above water reflectance Rrs coefficient, and the water attenuation coefficient Kd for fresh water. Different types of screens (totally absorbent, gray, etc.) were submerged in water (0-0.6 m) and illuminated from outside. The spectral density of the water leaving radiance was measured for different depths. The results were ran by a code which took into account the geometry of the incident irradiation, the geometry of the screen under water, and boundary conditions at the water surface provided by the radiation transfer theory. From the experimental data and our model we obtain the spectral distribution of the attenuation coefficient for fresh water and compared it with other data in literature. These experiments, performed in the Nonlinear Wave Lab at ERAU# represent just a preliminary calibration of the experimental protocol. More tests with water of different degrees of turbidity, and possibly wave filed at the water surface are in progress and will be presented in a forthcoming paper. △ Less

Submitted 17 August, 2014; originally announced August 2014.

Comments: 20 pages, 7 figures

MSC Class: 76xx; 78xx;

Existence and stability in a virtual interpolation method of the Stokes equations

Authors: Seong-Kwan Park, Gahyung Jo, Hi Jun Choe

Abstract: In this paper, we propose a new virtual interpolation point method to formulate the discrete Stokes equations. We form virtual staggered structure for the velocity and pressure from the actual computation node set. The virtual interpolation point method by a point collocation scheme is well suited to meshfree scheme since the approximation comes from smooth kernel and we can differentiate directly… ▽ More In this paper, we propose a new virtual interpolation point method to formulate the discrete Stokes equations. We form virtual staggered structure for the velocity and pressure from the actual computation node set. The virtual interpolation point method by a point collocation scheme is well suited to meshfree scheme since the approximation comes from smooth kernel and we can differentiate directly the kernels. The focus of this paper is laid on the contribution to a stable flow computation without explicit structure of staggered grid. In our method, we don't have to construct explicitly the staggered grid at all. Instead, there exists only virtual interpolation points at each computational node which play a key role in discretizing the conservative quantities of the Stokes equations. We prove the inf-sup condition for virtual interpolation point method with virtual structure of staggered grid and the existence and stability of discrete solutions. △ Less

Submitted 25 January, 2014; originally announced January 2014.

Comments: 16 pages, 21 figures

Virtual Interpolation Point Method for Viscous Flows in Complex Geometries

Authors: Seong-Kwan Park, Gahyung Jo, Hi Jun Choe

Abstract: A new approach for simulating flows over complex geometries is developed by introducing an accurate virtual interpolation point scheme as well as a virtual local stencil approach. The present method is based on the concept of point collocation on a virtual staggered structure together with a fractional step method. The use of a virtual staggered structure arrangement, which stores all the variable… ▽ More A new approach for simulating flows over complex geometries is developed by introducing an accurate virtual interpolation point scheme as well as a virtual local stencil approach. The present method is based on the concept of point collocation on a virtual staggered structure together with a fractional step method. The use of a virtual staggered structure arrangement, which stores all the variables at the same physical location and employs only one set of nodes using virtual interpolation points, reduces the geometrical complexity. The virtual staggered structure consists of the virtual interpolation points and the virtual local stencil. Also, computational enhancement of the virtual interpolation point method is considerable since the present method directly discretizes the strong forms of the incompressible Navier-Stokes equations without numerical integration. It makes a key difference from others. In the virtual interpolation point method, the choice of an accurate interpolation scheme satisfying the spatial approximation in the complex domain is important because there is the virtual staggered structure for computation of the velocities and pressure since there is no explicit staggered structure for stability. In our proposed method, the high order derivative approximations for constructing node-wise difference equations are easily obtained. Several different flow problems (decaying vortices, lid-driven cavity, triangular cavity, flow over a circular cylinder and a bumpy cylinder) are simulated using the virtual interpolation point method and the results agree very well with previous numerical and experimental results. They verify the accuracy of the present method. △ Less

Submitted 4 February, 2014; v1 submitted 25 January, 2014; originally announced January 2014.

Comments: 27 pages, 72 figures

Quasi-maximum modulus principle for the Stokes equations

Authors: Tongkeun Chang, Hi Jun Choe

Abstract: In this paper, we extend the maximum modulus estimate of the solutions of the nonstationary Stokes equations in the bounded $C^2$ cylinders for the space variables in \cite{CC} to time estimate. We show that if the boundary data is $L^\infty$ and the normal part of the boundary data has log-Dini continuity with respect to time, then the velocity is bounded. We emphasize that there is no continuity… ▽ More In this paper, we extend the maximum modulus estimate of the solutions of the nonstationary Stokes equations in the bounded $C^2$ cylinders for the space variables in \cite{CC} to time estimate. We show that if the boundary data is $L^\infty$ and the normal part of the boundary data has log-Dini continuity with respect to time, then the velocity is bounded. We emphasize that there is no continuity assumption on space variables in the new maximum modulus estimate. This completes the maximum modulus estimate. △ Less

Submitted 6 August, 2013; originally announced August 2013.

Maximum modulus estimate for the solution of the nonstationary Stokes equations

Authors: TongKeun Chang, Hi Jun Choe

Abstract: A maximum modulus estimate for the nonstationary Stokes equations in $C^2$ domain is found. The singular part and regular part of Poisson kernel are analyzed. The singular part consists of the gradient of single layer potential and the gradient of composite potential defined on only normal component of the boundary data. Furthermore, the normal velocity near the boundary is bounded if the boundary… ▽ More A maximum modulus estimate for the nonstationary Stokes equations in $C^2$ domain is found. The singular part and regular part of Poisson kernel are analyzed. The singular part consists of the gradient of single layer potential and the gradient of composite potential defined on only normal component of the boundary data. Furthermore, the normal velocity near the boundary is bounded if the boundary data is bounded. If the normal component of the boundary data is Dini-continuous and the tangential component of the boundary data is bounded, then the maximum modulus of velocity is bounded in whole domain. △ Less

Submitted 29 March, 2012; originally announced March 2012.

Manipulation of Spherical Droplets on a Liquid Platform Using Thermal Gradients

Authors: Ehsan Yakhshi-Tafti, Hyoung J. Cho, Ranganathan Kumar

Abstract: In the recent years, there has been a growing interest in droplet-based (digital) microfluidics for which, reliable means of droplet manipulation are required. In this study we demonstrate thermal actuation of droplets on liquid platforms, which is ideal for biochemical microsystems and lab-on-chip applications because droplets can be transported with high speed, good control and minimal thermal l… ▽ More In the recent years, there has been a growing interest in droplet-based (digital) microfluidics for which, reliable means of droplet manipulation are required. In this study we demonstrate thermal actuation of droplets on liquid platforms, which is ideal for biochemical microsystems and lab-on-chip applications because droplets can be transported with high speed, good control and minimal thermal loading as compared to using conventional solid substrates. In addition, other disadvantages of using solid surfaces such as evaporation, contamination, pinning, hysteresis and irreversibility of droplet motion are avoided. Based on the theoretical development and measurements, a silicon-based droplet transportation platform was developed with embedded Titanium micro heaters. A shallow liquid pool of inert liquid (FC-43) served as the carrier liquid. Heaters were interfaced with control electronics and driven through a computer graphical user interface. By creating appropriate spatio-temporal thermal gradient maps, transport of droplets on predetermined pathways was successfully demonstrated with high level of robustness, speed and reliability. The video shows normal imaging of droplet manipulation accompanied by the corresponding infrared thermal imaging showing the spatio-temporal temperature maps and the outline of the drop as it moves towards hot spots. △ Less

Submitted 15 October, 2010; originally announced October 2010.

Comments: 63rd APS - Division of Fluid Dynamics - 2010

Journal ref: Applied Physics Letters 96, 264101 (2010)

Drop Impact on Liquid Surfaces: Formation of Lens and Spherical Drops at the Air-Liquid Interface

Authors: Ehsan Yakhshi-Tafti, Hyoung J. Cho, Ranganathan Kumar

Abstract: Droplets at the air-liquid interface of immiscible liquids usually form partially-submerged lens shapes (e.g. water on oil). In addition to this structure, we showed that droplets released from critical heights above the target liquid can sustain the impact and at the end maintain a spherical ball-shape configuration above the surface, despite undergoing large deformation. Spherical drops are unst… ▽ More Droplets at the air-liquid interface of immiscible liquids usually form partially-submerged lens shapes (e.g. water on oil). In addition to this structure, we showed that droplets released from critical heights above the target liquid can sustain the impact and at the end maintain a spherical ball-shape configuration above the surface, despite undergoing large deformation. Spherical drops are unstable and will transform into the lens mode due to slight disturbances. Precision dispensing needles with various tip diameter sizes were used to release pendant drops of deionized water onto the surface of fluorocarbon liquid (FC-43, 3M). A cubic relationship was found between the nozzle tip diameter and the released droplet diameter. Drop impact was recorded by a high speed camera at a rate of 2000 frames per second. In order for the water drops to sustain the impact and retain a spherical configuration at the surface of the target liquid pool, it is required that they be of a critical size and be released from a certain height; otherwise the commonly observed lens shape droplets will form at the surface. △ Less

Submitted 15 October, 2010; originally announced October 2010.

Journal ref: E. Yakhshi-Tafti, H. J. Cho, and R. Kumar, Journal of Colloid and Interface Science 350, 373-376, 2010

Numerical Modeling of Complex Porous Media For Borehole Applications

Authors: Seungoh Ryu, Weishu Zhao, Gabriela Leu, Philip M. Singer, Hyung Joon Cho, Youngseuk Keehm

Abstract: The diffusion/relaxation behavior of polarized spins of pore filling fluid, as often probed by NMR relaxometry, is widely used to extract information on the pore-geometry. Such information is further interpreted as an indicator of the key transport property of the formation in the oil industry. As the importance of reservoirs with complex pore geometry grows, so does the need for deeper understa… ▽ More The diffusion/relaxation behavior of polarized spins of pore filling fluid, as often probed by NMR relaxometry, is widely used to extract information on the pore-geometry. Such information is further interpreted as an indicator of the key transport property of the formation in the oil industry. As the importance of reservoirs with complex pore geometry grows, so does the need for deeper understanding of how these properties are inter-related. Numerical modeling of relevant physical processes using a known pore geometry promises to be an effective tool in such endeavor. Using a suite of numerical techniques based on random-walk (RW) and Lattice-Boltzmann (LB) algorithms, we compare sandstone and carbonate pore geometries in their impact on NMR and flow properties. For NMR relaxometry, both laboratory measurement and simulation were done on the same source to address some of the long-standing issues in its borehole applications. Through a series of "numerical experiments" in which the interfacial relaxation properties of the pore matrix is varied systematically, we study the effect of a variable surface relaxivity while fully incorporating the complexity of the pore geometry. From combined RW and LB simulations, we also obtain diffusion-convection propagator and compare the result with experimental and network-simulation counterparts. △ Less

Submitted 13 August, 2009; v1 submitted 13 August, 2009; originally announced August 2009.

Comments: 6 pages, 6 color figures, Workshop GeoX10

Functional evolution of quantum cylindrical waves

Authors: Demian H. J. Cho, Madhavan Varadarajan

Abstract: Kucha{ř} showed that the quantum dynamics of (1 polarization) cylindrical wave solutions to vacuum general relativity is determined by that of a free axially-symmetric scalar field along arbitrary axially-symmetric foliations of a fixed flat 2+1 dimensional spacetime. We investigate if such a dynamics can be defined {\em unitarily} within the standard Fock space quantization of the scalar field.… ▽ More Kucha{ř} showed that the quantum dynamics of (1 polarization) cylindrical wave solutions to vacuum general relativity is determined by that of a free axially-symmetric scalar field along arbitrary axially-symmetric foliations of a fixed flat 2+1 dimensional spacetime. We investigate if such a dynamics can be defined {\em unitarily} within the standard Fock space quantization of the scalar field. Evolution between two arbitrary slices of an arbitrary foliation of the flat spacetime can be built out of a restricted class of evolutions (and their inverses). The restricted evolution is from an initial flat slice to an arbitrary (in general, curved) slice of the flat spacetime and can be decomposed into (i) `time' evolution in which the spatial Minkowskian coordinates serve as spatial coordinates on the initial and the final slice, followed by (ii) the action of a spatial diffeomorphism of the final slice on the data obtained from (i). We show that although the functional evolution of (i) is unitarily implemented in the quantum theory, generic spatial diffeomorphisms of (ii) are not. Our results imply that a Tomanaga-Schwinger type functional evolution of quantum cylindrical waves is not a viable concept even though, remarkably, the more limited notion of functional evolution in Kucha{ř}'s `half parametrized formalism' is well-defined. △ Less

Submitted 16 October, 2006; v1 submitted 11 May, 2006; originally announced May 2006.

Comments: Replaced with published version

Journal ref: Class.Quant.Grav.23:6115-6140,2006