-
Magnetic Force Microscopy: High Quality Factor Two-Pass Mode
Authors:
Christopher Habenschaden,
Sibylle Sievers,
Alexander Klasen,
Andrea Cerreta,
Hans Werner Schumacher
Abstract:
Magnetic force microscopy (MFM) is a well-established technique in scanning probe microscopy (SPM) that allows the imaging of magnetic samples with spatial resolution of tens of nm and stray fields down to the mT range. Spatial resolution and field sensitivity can be improved significantly by measuring in vacuum conditions. This effect originates from the higher quality factor (Q-factor) of the ca…
▽ More
Magnetic force microscopy (MFM) is a well-established technique in scanning probe microscopy (SPM) that allows the imaging of magnetic samples with spatial resolution of tens of nm and stray fields down to the mT range. Spatial resolution and field sensitivity can be improved significantly by measuring in vacuum conditions. This effect originates from the higher quality factor (Q-factor) of the cantilevers oscillation in vacuum compared to ambient conditions. However, while high Q-factors are desirable as they directly improve the magnetic measurement signal, they pose a challenge when pursuing a standard MFM two-pass (lift) mode measurement. At high Q-factors amplitude-based topography measurements become impossible and MFM phase response behaves non-linear. Here we present an implementation of a modified two-pass mode into a vacuum atomic force microscope (AFM) that overcomes these issues. By controlling Q in the first pass and using a phase-locked loop (PLL) technique in the second pass, high Q-factor measurements in vacuum are enabled. By measuring the cantilevers frequency shift instead of phase shift, otherwise emerging non-linearities are eliminated. The achievable improvements in resolution and sensitivity are demonstrated on patterned magnetic nanostructured samples. Elimination of non-linear response is showcased by a measurement of a very well-known calculable multilayer reference sample that is used for tip calibration in quantitative MFM (qMFM).
△ Less
Submitted 25 June, 2024;
originally announced June 2024.
-
Infrared ellipsometry study of the photo-generated charge carriers at the (001) and (110) surfaces of SrTiO$_3$ crystals and the interface of corresponding LaAlO$_3$/SrTiO$_3$ heterostructures
Authors:
M. Yazdi-Rizi,
P. Marsik,
B. P. P. Mallett,
K. Sen,
A. Cerreta,
A. Dubroka,
M. Scigaj,
F. Sánchez,
G. Herranz,
C. Bernhard
Abstract:
With infrared (IR) ellipsometry and DC resistance measurements we investigated the photo-do** at the (001) and (110) surfaces of SrTiO$_3$ (STO) single crystals and at the corresponding interfaces of LaAlO$_3$/SrTiO$_3$ (LAO/STO) heterostructures. In the bare STO crystals we find that the photo-generated charge carriers, which accumulate near the (001) surface, have a similar depth profile and s…
▽ More
With infrared (IR) ellipsometry and DC resistance measurements we investigated the photo-do** at the (001) and (110) surfaces of SrTiO$_3$ (STO) single crystals and at the corresponding interfaces of LaAlO$_3$/SrTiO$_3$ (LAO/STO) heterostructures. In the bare STO crystals we find that the photo-generated charge carriers, which accumulate near the (001) surface, have a similar depth profile and sheet carrier concentration as the confined electrons that were previously observed in LAO/STO (001) heterostructures. A large fraction of these photo-generated charge carriers persist at low temperature at the STO (001) surface even after the UV light has been switched off again. These persistent charge carriers seem to originate from oxygen vacancies that are trapped at the structural domain boundaries which develop below the so-called antiferrodistortive transition at T* = 105 K. This is most evident from a corresponding photo-do** study of the DC transport in STO (110) crystals for which the concentration of these domain boundaries can be modified by applying a weak uniaxial stress. The oxygen vacancies and their trap** by defects are also the source of the electrons that are confined to the interface of LAO/STO (110) heterostructures which likely do not have a polar discontinuity as in LAO/STO (001). In the former, the trap** and clustering of the oxygen vacancies also has a strong influence on the anisotropy of the charge carrier mobility. We show that this anisotropy can be readily varied and even inverted by various means, such as a gentle thermal treatment, UV irradiation, or even a weak uniaxial stress. Our experiments suggest that extended defects, which develop over long time periods (of weeks to months), can strongly influence the response of the confined charge carriers at the LAO/STO (110) interface.
△ Less
Submitted 8 February, 2017; v1 submitted 31 January, 2017;
originally announced February 2017.
-
Granular superconductivity and magnetic-field-driven recovery of macroscopic coherence in a cuprate/manganite multilayer
Authors:
B. P. P. Mallett,
J. Khmaladze,
P. Marsik,
E. Perret,
A. Cerreta,
M. Orlita,
N. Biškup,
M. Varela,
C. Bernhard
Abstract:
We show that in Pr$ _{0.5} $La$ _{0.2} $Ca$ _{0.3} $MnO$ _{3} $/YBa$ _{2} $Cu$ _{3} $O$ _{7} $ (PLCMO/YBCO) multilayers the low temperature state of YBCO is very resistive and resembles the one of a granular superconductor or a frustrated Josephson-junction network. Notably, a coherent superconducting response can be restored with a large magnetic field which also suppresses the charge-orbital ord…
▽ More
We show that in Pr$ _{0.5} $La$ _{0.2} $Ca$ _{0.3} $MnO$ _{3} $/YBa$ _{2} $Cu$ _{3} $O$ _{7} $ (PLCMO/YBCO) multilayers the low temperature state of YBCO is very resistive and resembles the one of a granular superconductor or a frustrated Josephson-junction network. Notably, a coherent superconducting response can be restored with a large magnetic field which also suppresses the charge-orbital order in PLCMO. This coincidence suggests that the granular superconducting state of YBCO is induced by the charge-orbital order of PLCMO. The coupling mechanism and the nature of the induced inhomogeneous state in YBCO remain to be understood.
△ Less
Submitted 13 November, 2016; v1 submitted 10 December, 2015;
originally announced December 2015.
