Showing 1–18 of 18 results for author: Bykov, I

Experimental end-to-end demonstration of intersatellite absolute ranging for LISA

Authors: Kohei Yamamoto, Iouri Bykov, Jan Niklas Reinhardt, Christoph Bode, Pascal Grafe, Martin Staab, Narjiss Messied, Myles Clark, Germán Fernández Barranco, Thomas S. Schwarze, Olaf Hartwig, Juan José Esteban Delgado, Gerhard Heinzel

Abstract: The Laser Interferometer Space Antenna (LISA) is a gravitational wave detector in space. It relies on a post-processing technique named time-delay interferometry (TDI) to suppress the overwhelming laser frequency noise by several orders of magnitude. This algorithm requires intersatellite-ranging monitors to provide information on spacecraft separations. To fulfill this requirement, we will use on… ▽ More The Laser Interferometer Space Antenna (LISA) is a gravitational wave detector in space. It relies on a post-processing technique named time-delay interferometry (TDI) to suppress the overwhelming laser frequency noise by several orders of magnitude. This algorithm requires intersatellite-ranging monitors to provide information on spacecraft separations. To fulfill this requirement, we will use on-ground observatories, optical sideband-sideband beatnotes, pseudo-random noise ranging (PRNR), and time-delay interferometric ranging (TDIR). This article reports on the experimental end-to-end demonstration of a hexagonal optical testbed used to extract absolute ranges via the optical sidebands, PRNR, and TDIR. These were applied for clock synchronization of optical beatnote signals sampled at independent phasemeters. We set up two possible PRNR processing schemes: Scheme 1 extracts pseudoranges from PRNR via a calibration relying on TDIR; Scheme 2 synchronizes all beatnote signals without TDIR calibration. The schemes rely on newly implemented monitors of local PRNR biases. After the necessary PRNR treatments (unwrap**, ambiguity resolution, bias correction, in-band jitter reduction, and/or calibration), Scheme 1 and 2 achieved ranging accuracies of 2.0 cm to 8.1 cm and 5.8 cm to 41.1 cm, respectively, below the classical 1 m mark with margins. △ Less

Submitted 5 June, 2024; originally announced June 2024.

Comments: 17 pages, 13 figures

Investigation of W-SiC compositionally graded films as a divertor material

Authors: Zihan Lin, Carlos Monton, Stefan Bringuier, Gregory Sinclair, Guangming Cheng, Eduardo Marin, Zachary Bergstrom, Dmitry Rudakov, Žana Popović, Ulises Losada, Igor Bykov, Evan T. Ostrowski, Shota Abe, Nan Yao, Bruce E. Koel, Tyler Abrams

Abstract: W-SiC composite material is a promising plasma-facing material candidate alternative to pure W due to the low neutron activation, low impurity radiation, and low tritium diffusivity of SiC while leveraging the high erosion resistance of the W armor. Additionally, W and SiC have high thermomechanical compatibility given their similar thermal expansion rates. The present study addresses the synthesi… ▽ More W-SiC composite material is a promising plasma-facing material candidate alternative to pure W due to the low neutron activation, low impurity radiation, and low tritium diffusivity of SiC while leveraging the high erosion resistance of the W armor. Additionally, W and SiC have high thermomechanical compatibility given their similar thermal expansion rates. The present study addresses the synthesis and performance of compositionally graded W-SiC films fabricated by pulsed-DC magnetron sputtering. Compositional gradients were characterized using transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS), and crystallographic information was obtained using electron diffraction and X-ray diffraction (XRD). Samples were exposed to L-mode deuterium plasma discharges in the DIII-D tokamak using the Divertor Material Evaluation System (DiMES). Post-mortem characterizations were performed using scanning electron microscopy (SEM) and XRD. Electron diffraction and XRD showed that the compositionally graded W-SiC films were composed of polycrystalline W and amorphous SiC with amorphous W+SiC interlayers. No macroscopic delamination or microstructural changes were observed under mild exposure conditions. This study serves as a preliminary examination of W-SiC compositionally graded composites as a potential candidate divertor material in future tokamak devices. △ Less

Submitted 15 February, 2024; v1 submitted 30 August, 2023; originally announced August 2023.

Comments: Published in Journal of Nuclear Materials

Journal ref: J. Nucl. Mater. 592 (2024) 154942

In-situ coating of silicon-rich films on tokamak plasma-facing components with real-time Si material injection

Authors: Florian Effenberg, Shota Abe, Gregory Sinclair, Tyler Abrams, Alessandro Bortolon, William R. Wampler, Florian M. Laggner, Dmitry L. Rudakov, Igor Bykov, Charles J. Lasnier, David Mauzey, Alexander Nagy, Raffi Nazikian, Filippo Scotti, Huiqian Wang, Robert S. Wilcox, the DIII-D Team

Abstract: Experiments have been conducted in the DIII-D tokamak to explore the in-situ growth of silicon-rich layers as a potential technique for real-time replenishment of surface coatings on plasma-facing components (PFCs) during steady-state long-pulse reactor operation. Silicon (Si) pellets of 1 mm diameter were injected into low- and high-confinement (L-mode and H-mode) plasma discharges with densities… ▽ More Experiments have been conducted in the DIII-D tokamak to explore the in-situ growth of silicon-rich layers as a potential technique for real-time replenishment of surface coatings on plasma-facing components (PFCs) during steady-state long-pulse reactor operation. Silicon (Si) pellets of 1 mm diameter were injected into low- and high-confinement (L-mode and H-mode) plasma discharges with densities ranging from $3.9-7.5\times10^{19}$ m$^{-3}$ and input powers ranging from $5.5-9$ MW. The small Si pellets were delivered with the impurity granule injector (IGI) at frequencies ranging from 4-16 Hz corresponding to mass flow rates of $5-19$ mg/s ($1-4.2\times10^{20}$ Si/s) at cumulative amounts of up to 34 mg of Si per five-second discharge. Graphite samples were exposed to the scrape-off layer and private flux region plasmas through the divertor material evaluation system (DiMES) to evaluate the Si deposition on the divertor targets. The Si II emission at the sample correlates with silicon injection and suggests net surface Si-deposition in measurable amounts. Post-mortem analysis showed Si-rich coatings containing silicon oxides, of which SiO$_2$ is the dominant component. No evidence of SiC was found, which is attributed to low divertor surface temperatures. The in-situ and ex-situ analysis found that Si-rich coatings of at least $0.4-1.2$ nm thickness have been deposited at $0.4-0.7$ nm/s. The technique is estimated to coat a surface area of at least 0.94 m$^2$ on the outer divertor. These results demonstrate the potential of using real-time material injection to form Si-enriched layers on divertor PFCs during reactor operation. △ Less

Submitted 9 August, 2023; v1 submitted 8 April, 2023; originally announced April 2023.

Comments: Florian Effenberg et al 2023 Nucl. Fusion in press https://doi.org/10.1088/1741-4326/acee98

Journal ref: Nucl. Fusion 63 106004 (2023)

Mitigation of plasma-wall interactions with low-Z powders in DIII-D high confinement plasmas

Authors: Florian Effenberg, Alessandro Bortolon, Livia Casali, Raffi Nazikian, Igor Bykov, Filippo Scotti, Huiqian Q. Wang, Max E. Fenstermacher, Robert Lunsford, Alexander Nagy, Brian A. Grierson, Florian M. Laggner, Rajesh Maingi, the DIII-D Team

Abstract: Experiments with low-Z powder injection in DIII-D high confinement discharges demonstrated increased divertor dissipation and detachment while maintaining good core energy confinement. Lithium (Li), boron (B), and boron nitride (BN) powders were injected in high-confinement mode plasmas ($I_p=$1 MA, $B_t=$2 T, $P_{NB}=$6 MW, $\langle n_e\rangle=3.6-5.0\cdot10^{19}$ m$^{-3}$) into the upper small-a… ▽ More Experiments with low-Z powder injection in DIII-D high confinement discharges demonstrated increased divertor dissipation and detachment while maintaining good core energy confinement. Lithium (Li), boron (B), and boron nitride (BN) powders were injected in high-confinement mode plasmas ($I_p=$1 MA, $B_t=$2 T, $P_{NB}=$6 MW, $\langle n_e\rangle=3.6-5.0\cdot10^{19}$ m$^{-3}$) into the upper small-angle slot (SAS) divertor for 2-s intervals at constant rates of 3-204 mg/s. The multi-species BN powders at a rate of 54 mg/s showed the most substantial increase in divertor neutral compression by more than an order of magnitude and lasting detachment with minor degradation of the stored magnetic energy $W_{mhd}$ by 5%. Rates of 204 mg/s of boron nitride powder further reduce ELM-fluxes on the divertor but also cause a drop in confinement performance by 24% due to the onset of an $n=2$ tearing mode. The application of powders also showed a substantial improvement of wall conditions manifesting in reduced wall fueling source and intrinsic carbon and oxygen content in response to the cumulative injection of non-recycling materials. The results suggest that low-Z powder injection, including mixed element compounds, is a promising new core-edge compatible technique that simultaneously enables divertor detachment and improves wall conditions during high confinement operation. △ Less

Submitted 16 August, 2022; v1 submitted 28 March, 2022; originally announced March 2022.

Comments: F. Effenberg et al 2022 Nucl. Fusion in press https://doi.org/10.1088/1741-4326/ac899d

Journal ref: Nucl. Fusion 62 106015 (2022)

Plasmon localization and giant fields in holographic metasurface for SERS sensors

Authors: Andrey K. Sarychev, Andrey Ivanov, Andrey N. Lagarkov, Gregory Barbillon, Igor Bykov, Ilya Ryzhikov, Konstantin Afanasev, Nikita Bakholdin, Mikhail Mikhailov, Alexander Smyk, Alexander Shurygin, Alexander Shalygin

Abstract: We present SERS-active metal holographic metasurfaces fabricated from metal periodical nanograting deposited on a dielectric substrate. The metasurface consists of a modulated dielectric, which is covered by a thin silver layer. The metasurface operates as an open plasmon resonator. The theory of plasmons excited in the open resonator formed by a metal nanograting is presented. The large local ele… ▽ More We present SERS-active metal holographic metasurfaces fabricated from metal periodical nanograting deposited on a dielectric substrate. The metasurface consists of a modulated dielectric, which is covered by a thin silver layer. The metasurface operates as an open plasmon resonator. The theory of plasmons excited in the open resonator formed by a metal nanograting is presented. The large local electromagnetic field is predicted for optical frequencies. The excitation of plasmons is experimentally demonstrated in the metasurface designed on a 4-inch Si wafer. The enhancement of the local electric field results in surface-enhanced Raman scattering (SERS). To investigate the SERS effect, the metasurfaces are covered by molecules of 4-mercaptophenylboronic acid, which form covalent bonds with the silver nanolayer and serve as a proof-of-concept. Finally, we obtain a detection limit of 230 nM for molecules of 4-mercaptophenylboronic acid. △ Less

Submitted 9 November, 2021; originally announced November 2021.

Comments: 12 pages, 11 figures, 67 references

Design and Testing of Dimes Carbon Ablation Rods in the DIII-D Tokamak

Authors: Dmitri M. Orlov, Michael O. Hanson, Jason Escalera, Hadith Taheri, Caitlin N. Villareal, Daniel M. Zubovic, Igor Bykov, Evdokiya G. Kostadinova, Dmitri L. Rudakov, Maziar Ghazinejad

Abstract: We present the design of ATJ graphite rods developed for ablation experiments under high heat flux (up to 50 MW/m2) in the lower divertor of the DIII-D tokamak [1], a magnetic plasma confinement device. This work is motivated by the need to test ablation models relevant to carbon-based thermal shields used in high-speed spacecraft atmospheric entries, where the heat fluxes encountered can be compa… ▽ More We present the design of ATJ graphite rods developed for ablation experiments under high heat flux (up to 50 MW/m2) in the lower divertor of the DIII-D tokamak [1], a magnetic plasma confinement device. This work is motivated by the need to test ablation models relevant to carbon-based thermal shields used in high-speed spacecraft atmospheric entries, where the heat fluxes encountered can be comparable to those achieved in the DIII-D divertor plasma. Several different designs for the flow-facing side of the rod are analyzed, including "sharp nose," "blunt," and "concave". The last shape is studied for its potential to lower heat fluxes at the rod surface by increased radiation from trapped neutrals and reduced parallel plasma pressure. We also analyze the possibility of applying a thin (approximately 30 microns) layer of silicon carbide (SiC) to the exposed part of several carbon ablation rods to benchmark its erosion calculations and lifetime predictions. Such calculations are of interest as SiC represents a promising material for both thermal protection systems (TPS) and a fusion plasma-facing material (PFM). Preliminary results from the DIII-D rod ablation experiments are also discussed. △ Less

Submitted 15 June, 2021; originally announced June 2021.

Runaway Electron Seed Formation at Reactor-Relevant Temperature

Authors: C. Paz-Soldan, P. Aleynikov, E. M. Hollmann, A. Lvovskiy, I. Bykov, X. Du, N. W. Eidietis, D. Shiraki

Abstract: Systematic variation of the pre-disruption core electron temperature (Te) from 1 to 12 keV using an internal transport barrier scenario reveals a dramatic increase in the production of seed runaway electrons (REs), ultimately accessing near-complete conversion of the pre-disruption current into sub-MeV RE current. Injected Ar pellets are observed to ablate more intensely and promptly as Te rises.… ▽ More Systematic variation of the pre-disruption core electron temperature (Te) from 1 to 12 keV using an internal transport barrier scenario reveals a dramatic increase in the production of seed runaway electrons (REs), ultimately accessing near-complete conversion of the pre-disruption current into sub-MeV RE current. Injected Ar pellets are observed to ablate more intensely and promptly as Te rises. At high Te, the observed ablation exceeds predictions from published thermal ablation models. Simultaneously, the thermal quench (TQ) is observed to significantly shorten with increasing Te -- a surprising result. While the reason for the shorter TQ is not yet understood, candidate mechanisms include: insufficiently accurate thermal ablation models, enhanced ablation driven by the seed RE population, or significant parallel heat transport along stochastic fields. Kinetic modeling that self-consistently treats the plasma cooling via radiation, the induced electric field, and the formation of the seed RE is performed. Including the combined effect of the inherent dependence of hot-tail RE seeding on Te together with the shortened TQ, modeling recovers the progression towards near-complete conversion of the pre-disruption current to RE current as Te rises. Measurement of the HXR spectrum during the early current quench (CQ) reveals a trend of decreasing energy with pre-disruption Te. At the very highest Te ($\approx$ 12 keV), $\approx$ 100% conversion of the thermal current to runaway current is found. The energy of this peculiar RE beam is inferred to be sub-MeV as it emits vanishingly few MeV hard X-rays (HXRs). These measurements demonstrate novel TQ dynamics as Te is varied and illustrate the limitations of treating the RE seed formation problem without considering the inter-related dependencies of the pellet ablation, radiative energy loss, and resultant variations of the TQ duration. △ Less

Submitted 12 February, 2020; originally announced February 2020.

Dust remobilization in fusion plasmas under steady state conditions

Authors: P. Tolias, S. Ratynskaia, M. De Angeli, G. De Temmerman, D. Ripamonti, G. Riva, I. Bykov, A. Shalpegin, L. Vignitchouk, F. Brochard, K. Bystrov, S. Bardin, A. Litnovsky

Abstract: The first combined experimental and theoretical studies of dust remobilization by plasma forces are reported. The main theoretical aspects of remobilization in fusion devices under steady state conditions are analyzed. In particular, the dominant role of adhesive forces is highlighted and generic remobilization conditions - direct lift-up, sliding, rolling - are formulated. A novel experimental te… ▽ More The first combined experimental and theoretical studies of dust remobilization by plasma forces are reported. The main theoretical aspects of remobilization in fusion devices under steady state conditions are analyzed. In particular, the dominant role of adhesive forces is highlighted and generic remobilization conditions - direct lift-up, sliding, rolling - are formulated. A novel experimental technique is proposed, based on controlled adhesion of dust grains on tungsten samples combined with detailed map** of the dust deposition profile prior and post plasma exposure. Proof-of-principle experiments in the TEXTOR tokamak and the EXTRAP-T2R reversed-field pinch are presented. The versatile environment of the linear device Pilot-PSI allowed for experiments with different magnetic field topologies and varying plasma conditions that were complemented with camera observations. △ Less

Submitted 18 November, 2015; v1 submitted 25 August, 2015; originally announced August 2015.

Comments: 16 pages, 11 figures, 3 tables

Journal ref: Plasma Phys. Control. Fusion 58, 025009 (2016)

Readout for intersatellite laser interferometry: Measuring low frequency phase fluctuations of HF signals with microradian precision

Authors: Oliver Gerberding, Christian Diekmann, Joachim Kullmann, Michael Tröbs, Ioury Bykov, Simon Barke, Nils Christopher Brause, Juan José Esteban Delgado, Thomas S. Schwarze, Jens Reiche, Karsten Danzmann, Torben Rasmussen, Torben Vendt Hansen, Anders Engaard, Søren Møller Pedersen, Oliver Jennrich, Martin Suess, Zoran Sodnik, Gerhard Heinzel

Abstract: Precision phase readout of optical beat note signals is one of the core techniques required for intersatellite laser interferometry. Future space based gravitational wave detectors like eLISA require such a readout over a wide range of MHz frequencies, due to orbit induced Doppler shifts, with a precision in the order of $μ\textrm{rad}/\sqrt{\textrm{Hz}}$ at frequencies between… ▽ More Precision phase readout of optical beat note signals is one of the core techniques required for intersatellite laser interferometry. Future space based gravitational wave detectors like eLISA require such a readout over a wide range of MHz frequencies, due to orbit induced Doppler shifts, with a precision in the order of $μ\textrm{rad}/\sqrt{\textrm{Hz}}$ at frequencies between $0.1\,\textrm{mHz}$ and $1\,\textrm{Hz}$. In this paper, we present phase readout systems, so-called phasemeters, that are able to achieve such precisions and we discuss various means that have been employed to reduce noise in the analogue circuit domain and during digitisation. We also discuss the influence of some non-linear noise sources in the analogue domain of such phasemeters. And finally, we present the performance that was achieved during testing of the elegant breadboard model of the LISA phasemeter, that was developed in the scope of an ESA technology development activity. △ Less

Submitted 30 April, 2015; originally announced April 2015.

Comments: submitted to Review of Scientific Instruments on April 30th 2015

Journal ref: Rev. Sci. Instrum. 86, 074501 (2015)

Phasemeter core for intersatellite laser heterodyne interferometry: modelling, simulations and experiments

Authors: Oliver Gerberding, Benjamin Sheard, Iouri Bykov, Joachim Kullmann, Juan Jose Esteban Delgado, Karsten Danzmann, Gerhard Heinzel

Abstract: Inter satellite laser interferometry is a central component of future space-borne gravity instruments like LISA, eLISA, NGO and future geodesy missions. The inherently small laser wavelength allows to measure distance variations with extremely high precision by interfering a reference beam with a measurement beam. The readout of such interferometers is often based on tracking phasemeters, able to… ▽ More Inter satellite laser interferometry is a central component of future space-borne gravity instruments like LISA, eLISA, NGO and future geodesy missions. The inherently small laser wavelength allows to measure distance variations with extremely high precision by interfering a reference beam with a measurement beam. The readout of such interferometers is often based on tracking phasemeters, able to measure the phase of an incoming beatnote with high precision over a wide range of frequencies. The implementation of such phasemeters is based on all digital phase-locked loops, hosted in FPGAs. Here we present a precise model of an all digital phase locked loop that allows to design such a readout algorithm and we support our analysis by numerical performance measurements and experiments with analog signals. △ Less

Submitted 9 October, 2013; originally announced October 2013.

Comments: 17 pages, 6 figures, accepted for publication in CQG

Journal ref: Classical and Quantum Gravity, Volume 30, Number 23 (2013)

The Gravitational Universe

Authors: The eLISA Consortium, :, P. Amaro Seoane, S. Aoudia, H. Audley, G. Auger, S. Babak, J. Baker, E. Barausse, S. Barke, M. Bassan, V. Beckmann, M. Benacquista, P. L. Bender, E. Berti, P. Binétruy, J. Bogenstahl, C. Bonvin, D. Bortoluzzi, N. C. Brause, J. Brossard, S. Buchman, I. Bykov, J. Camp, C. Caprini , et al. (136 additional authors not shown)

Abstract: The last century has seen enormous progress in our understanding of the Universe. We know the life cycles of stars, the structure of galaxies, the remnants of the big bang, and have a general understanding of how the Universe evolved. We have come remarkably far using electromagnetic radiation as our tool for observing the Universe. However, gravity is the engine behind many of the processes in th… ▽ More The last century has seen enormous progress in our understanding of the Universe. We know the life cycles of stars, the structure of galaxies, the remnants of the big bang, and have a general understanding of how the Universe evolved. We have come remarkably far using electromagnetic radiation as our tool for observing the Universe. However, gravity is the engine behind many of the processes in the Universe, and much of its action is dark. Opening a gravitational window on the Universe will let us go further than any alternative. Gravity has its own messenger: Gravitational waves, ripples in the fabric of spacetime. They travel essentially undisturbed and let us peer deep into the formation of the first seed black holes, exploring redshifts as large as z ~ 20, prior to the epoch of cosmic re-ionisation. Exquisite and unprecedented measurements of black hole masses and spins will make it possible to trace the history of black holes across all stages of galaxy evolution, and at the same time constrain any deviation from the Kerr metric of General Relativity. eLISA will be the first ever mission to study the entire Universe with gravitational waves. eLISA is an all-sky monitor and will offer a wide view of a dynamic cosmos using gravitational waves as new and unique messengers to unveil The Gravitational Universe. It provides the closest ever view of the early processes at TeV energies, has guaranteed sources in the form of verification binaries in the Milky Way, and can probe the entire Universe, from its smallest scales around singularities and black holes, all the way to cosmological dimensions. △ Less

Submitted 24 May, 2013; originally announced May 2013.

Comments: 20 pages; submitted to the European Space Agency on May 24th, 2013 for the L2/L3 selection of ESA's Cosmic Vision program

Breadboard model of the LISA phasemeter

Authors: Oliver Gerberding, Simon Barke, Ioury Bykov, Karsten Danzmann, Anders Enggaard, Juan Jose Esteban, Alberto Gianolio, Torben Vendt Hansen, Gerhard Heinzel, Allan Hornstrup, Oliver Jennrich, Joachim Kullmann, Søren Møller Pedersen, Torben Rasmussen, Jens Reiche, Zoran Sodnik, Martin Suess

Abstract: An elegant breadboard model of the LISA phasemeter is currently under development by a Danish-German consortium. The breadboard is build in the frame of an ESA technology development activity to demonstrate the feasibility and readiness of the LISA metrology baseline architecture. This article gives an overview about the breadboard design and its components, including the distribution of key funct… ▽ More An elegant breadboard model of the LISA phasemeter is currently under development by a Danish-German consortium. The breadboard is build in the frame of an ESA technology development activity to demonstrate the feasibility and readiness of the LISA metrology baseline architecture. This article gives an overview about the breadboard design and its components, including the distribution of key functionalities. △ Less

Submitted 27 January, 2013; v1 submitted 31 August, 2012; originally announced August 2012.

Comments: 5 pages, 3 figures, published in ASP Conference Series, Vol. 467, 9th LISA Symposium (2012), pp 271-276

Electron spin resonance investigation of Mn^{2+} ions and their dynamics in manganese doped SrTiO_3

Authors: V. V. Laguta, I. V. Kondakova, I. P. Bykov, M. D. Glinchuk, P. M. Vilarinho, A. Tkach, L. Jastrabik

Abstract: Using electron spin resonance, lattice position and dynamic properties of Mn2+ ions were studied in 0.5 and 2 % manganese doped SrTiO3 ceramics prepared by conventional mixed oxide method. The measurements showed that Mn2+ ions substitute preferably up to 97 % for Sr if the ceramics is prepared with a deficit of Sr ions. Motional narrowing of the Mn2+ ESR spectrum was observed when temperature i… ▽ More Using electron spin resonance, lattice position and dynamic properties of Mn2+ ions were studied in 0.5 and 2 % manganese doped SrTiO3 ceramics prepared by conventional mixed oxide method. The measurements showed that Mn2+ ions substitute preferably up to 97 % for Sr if the ceramics is prepared with a deficit of Sr ions. Motional narrowing of the Mn2+ ESR spectrum was observed when temperature increases from 120 K to 240-250 K that was explained as a manifestation of off-center position of this ion at the Sr site. From the analysis of the ESR spectra the activation energy Ea = 86 mV and frequency factor 1/?0 ? (2-10)x10^(-14) 1/s for jum** of the impurity between symmetrical off-center positions were determined. Both values are in agreement with those derived previously from dielectric relaxation. This proves the origin of dielectric anomalies in SrTiO3:Mn as those produced by the reorientation dynamics of Mn2+ dipoles. △ Less

Submitted 28 February, 2007; originally announced February 2007.

Comments: 16 pages, 6 figures

Dipole glass and mixed ferroglass phase in SrTiO3 ceramics doped with manganese

Authors: M. D. Glinchuk, P. I. Bykov

Abstract: Recently new incipient ferroelectrics with off-center ions SrTiO3 with Mn2+ substituted for Sr2+ was revealed (Tkach et. al PRB 73, 104113 (2006). Experimental investigation of Sr1-xMnxTiO3 properties, namely temperature, frequency and external electric field dependence of dielectric permittivity at different concentrations gave evidence about phase transitions induced by the impurities. However… ▽ More Recently new incipient ferroelectrics with off-center ions SrTiO3 with Mn2+ substituted for Sr2+ was revealed (Tkach et. al PRB 73, 104113 (2006). Experimental investigation of Sr1-xMnxTiO3 properties, namely temperature, frequency and external electric field dependence of dielectric permittivity at different concentrations gave evidence about phase transitions induced by the impurities. However their nature was not found out up to now because of the absence of the theoretical analysis of the results. In this paper we performed such analysis by the theoretical description of the temperature of dielectric permittivity maxima dependence on Mn2+ concentration, the change of residual polarization with temperature, frequency and temperature dependence of the permittivity with Arrhenius and Vogel-Fulcher law at smaller and larger concentration respectively. The obtained results had shown that at x less than 0,03 and x between 0,15 and 0,03 the considered system Sr1-xMnxTiO3 is in dipole glass state and mixed ferroglass phase respectively. △ Less

Submitted 7 December, 2006; originally announced December 2006.

Comments: 8 pages, 3 figures

The mechanism of the decrease of barriers for oxygen ionic conductivity in nanocrystalline ceramics

Authors: M. D. Glinchuk, P. I. Bykov, B. Hilczer

Abstract: We calculated the influence of surface tension on the barriers of oxygen ionic conductivity in nanograin ceramics. Activation energy of oxygen ions diffusion via oxygen vacancies which were considered as the dilatational centers was calculated. This energy was shown to decrease with nanoparticle sizes decreasing. The distribution function of activation energy was derived on the basis of distribu… ▽ More We calculated the influence of surface tension on the barriers of oxygen ionic conductivity in nanograin ceramics. Activation energy of oxygen ions diffusion via oxygen vacancies which were considered as the dilatational centers was calculated. This energy was shown to decrease with nanoparticle sizes decreasing. The distribution function of activation energy was derived on the basis of distribution of nanoparticle sizes. We obtained an analytical expressions of ionic conductivity dependence on the temperature and nanograin sizes. These formulas fitted pretty good the observed earlier behaviour of oxygen conductivity in nanograin ceramics of ZrO2:16% Y observed earlier. Therefore the consideration we carried out had shown that the surface tension in nanoparticles is physical mechanism responsible for the essential enhancement of the oxygen ionic conductivity observed in nanograin samples, the main contribution to the conductivity being related to the region in vicinity of the particle surface. △ Less

Submitted 6 July, 2005; originally announced July 2005.

Comments: 8 pages, 7 figures

Size effects in radiospectroscopy spectra of ferroelectric nanopowders

Authors: M. D. Glinchuk, I. V. Kondakova, A. M. Slipenyuk, I. P. Bykov, V. V. Laguta, A. V. Ragulya, V. P. Klimenko

Abstract: The theoretical and experimental investigation of ferroelectric nanopowders is performed. The manifestation in radiospectroscopy spectra of size driven ferroelectric-paraelectric phase transition at some critical particle average size was the main goal of the consideration. In theoretical part the size effect for the materials with ferroelectric tetragonal phase and cubic paraelectric phase was… ▽ More The theoretical and experimental investigation of ferroelectric nanopowders is performed. The manifestation in radiospectroscopy spectra of size driven ferroelectric-paraelectric phase transition at some critical particle average size was the main goal of the consideration. In theoretical part the size effect for the materials with ferroelectric tetragonal phase and cubic paraelectric phase was considered allowing for the spontaneous polarization inhomogeneity inside a particle and distribution of particle sizes. In ESR the transformation of the spectra from tetragonal symmetry to cubic symmetry with decreasing of nanoparticle sizes was calculated. Measurements of Fe3+ ESR spectra in nanopowder of BaTiO3 were carried out at room temperature. The decrease of intensity of tetragonal symmetry ESR lines of Fe3+ and appearance of cubic symmetry line with asymmetry of the shoulders was observed with the average sizes decrease with complete disappearance of tetragonal spectrum at average size less or equal 40 nm. The comparison of the theory with experiment was carried out. The value of critical size Rc = 40 nm was extracted from ESR data. The asymmetry and broadening of right hand side shoulder of ESR cubic symmetry line was shown to be related to contribution of paramagnetic centers in the vicinity of the particles surface. The deconvolution of the cubic line allowed to show, that this region size is about 3 nm. △ Less

Submitted 25 May, 2005; originally announced May 2005.

Comments: 10 pages, 8 figures

The anomalies of the properties of nanomaterials related to the distribution of the grain sizes

Authors: M. D. Glinchuk, P. I. Bykov

Abstract: We have performed the calculations of the size effect in the temperature dependence of BaTiO3 nanograin ceramics specific heat and dielectric permittivity. We took into account the distribution of the grain sizes, that exists in any real nanomaterial. This distribution lead to the distribution of the temperatures of the size driven transition from ferroelectric to paraelectric phase because of r… ▽ More We have performed the calculations of the size effect in the temperature dependence of BaTiO3 nanograin ceramics specific heat and dielectric permittivity. We took into account the distribution of the grain sizes, that exists in any real nanomaterial. This distribution lead to the distribution of the temperatures of the size driven transition from ferroelectric to paraelectric phase because of relation between the temperature and the sizes. We calculated the transition temperature distribution function on the basis of the sizes distribution function. This function allowed to calculate the temperature dependence of any physical quantity in a nanomaterial. As an examples we calculated specific heat and dielectric permittivity in nanograin ferroelectric ceramics. The results demonstrate the strong influence of the size distribution on the observed properties and especially on extracted from experiment values of critical size and temperature. We carried out the comparison of the theory with the measured specific heat and dielectric permittivity in BaTiO3 nanomaterial. The developed theory described the experimental data pretty good. The possibility of the extraction of size distribution function parameters as well as real values of critical parameters from experimental data is discussed. △ Less

Submitted 1 June, 2004; originally announced June 2004.

Comments: 9 pages, 6 figures, 2 tables

NMR comparative study of PbMg_1/3Nb_2/3O_3 and PbSc_1/2Nb_1/2O_3 local structure

Authors: V. V. Laguta, M. D. Glinchuk, I. P. Bykov, R. Blinc, A. Gregorovic, B. Zalar

Abstract: The 93Nb and 45Sc NMR spectra in PbSc_1/2Nb_1/2O_3 (PSN) and PbMg_1/3Nb_2/3O_3 (PMN) disordered relaxor ferroelectrics at the temperature T > T_0 (T_0 is the temperature of the dielectric susceptibility maximum) have been studied. Spectra analysis was performed on the base both of the analytical description of NMR lines shapes, allowing for homogeneous and inhomogeneous broadening related to a r… ▽ More The 93Nb and 45Sc NMR spectra in PbSc_1/2Nb_1/2O_3 (PSN) and PbMg_1/3Nb_2/3O_3 (PMN) disordered relaxor ferroelectrics at the temperature T > T_0 (T_0 is the temperature of the dielectric susceptibility maximum) have been studied. Spectra analysis was performed on the base both of the analytical description of NMR lines shapes, allowing for homogeneous and inhomogeneous broadening related to a random distribution of the electric field gradients and numerical Monte Carlo method taking into account electric field gradients originated from random distribution of Mg, Sc and Nb ions (which may be shifted or not) over B-type cation sites. The observed 1/2 -1/2 transition spectrum both of the 93Nb and 45Sc nuclei in the PSN was shown to contain a narrow (3-4 kHz) almost isotropic part and a broad strongly anisotropic part. These two components of NMR spectra are related to 1:1 Sc/Nb ordered and compositionally disordered regions of the crystal, respectively. It was shown that in the disordered regions Sc^3+, Nb^5+ and O^2- ions are shifted from their cubic lattice sites at one of three possible directions: <100>, <110> or <111>. In PMN the NMR spectrum of 93Nb contains practically only the broad component. The portion of unbroadened spectrum that may correspond to ideal 1:2 regions accounts only for 1-2 percent of the total integral intensity. No evidance was obtained about existence of the 1:1 regions in PMN. The NMR data demonstrate that in PMN the cubic symmetry at T > T_0 is locally broken due to ions shifts similar to that in disordered PSN. The values of the ion shifts were estimated in the point charges point dipoles approximation of the electric field gradients calculation both in the PSN and PMN. △ Less

Submitted 1 February, 2002; v1 submitted 31 January, 2002; originally announced January 2002.