-
Sensitivity in Nanomechanical Pedestal MEMS Cantilever
Authors:
Abhay K. Rajak,
Ritambhara Dash,
Ashwini Kumari,
A. S. Bhattacharyya
Abstract:
Nanomechanical resonator-based sensing devices are used in medical diagnostics based on their high-frequency dynamic behavior. Cantilevers fall into the category of Nanomechanical resonators. It also resembles a resonator whose shape is like that of a nanowire clamped at one end. As the surface-to-volume ratio of a nanowire resonator increases due to scaling down, surface stress plays a crucial ro…
▽ More
Nanomechanical resonator-based sensing devices are used in medical diagnostics based on their high-frequency dynamic behavior. Cantilevers fall into the category of Nanomechanical resonators. It also resembles a resonator whose shape is like that of a nanowire clamped at one end. As the surface-to-volume ratio of a nanowire resonator increases due to scaling down, surface stress plays a crucial role in the mechanical behavior of a resonator. Piezoresistive MEMS cantilevers are used for vapor phase analysis of volatile compounds and gas. Studies were done to address the mass sensitivity issues and fractures associated with bioceramic and nanocomposite coatings-based cantilever resonators. The studies show how the sensing performance can be determined or tuned. Nanomechanical studies of thin films of SiCN on silicon were performed. The sharpness of the tip was found to have an influence on the tip-sample conduction mechanism useful for MEMS applications
△ Less
Submitted 4 August, 2023;
originally announced August 2023.
-
Characterization of Zinc oxide & Aluminum Ferrite and Simulation studies of M-H plots of Cobalt/Cobaltoxide
Authors:
Prashant Kumar,
Balram S. Yadav,
Komal Singh,
A. S. Bhattacharyya
Abstract:
Zinc oxide and Aluminum Ferrite were prepared Chemical route. The samples were characterized by XRD and VSM. Simulation of M-H plots of Co/CoO thin films were performed. Effect of parameters was observed on saturation magnetization.
Zinc oxide and Aluminum Ferrite were prepared Chemical route. The samples were characterized by XRD and VSM. Simulation of M-H plots of Co/CoO thin films were performed. Effect of parameters was observed on saturation magnetization.
△ Less
Submitted 4 July, 2022; v1 submitted 25 April, 2017;
originally announced May 2017.
-
Nanoindentation stress-strain for Fracture Analysis and computational modeling for hardness and modulus
Authors:
A. S. Bhattacharyya,
S Priyadarshi,
S. Sonu,
S. Shivam,
S. Anshu
Abstract:
Stress-strain plots based on nanoindentation load-depth curves reflected cracking phenomenon. A transition from ductile to brittle fracture was observed on increasing the depth or load of indenter penetration. A new approach with shape factors in the fracture studies based on radial crack branching and micro-cracking was done. Hardness and modulus plots were fitted with polynomials. The coefficien…
▽ More
Stress-strain plots based on nanoindentation load-depth curves reflected cracking phenomenon. A transition from ductile to brittle fracture was observed on increasing the depth or load of indenter penetration. A new approach with shape factors in the fracture studies based on radial crack branching and micro-cracking was done. Hardness and modulus plots were fitted with polynomials. The coefficients were varied to obtain different hardness and modulus responses.
△ Less
Submitted 12 April, 2017;
originally announced April 2017.
-
Raman studies on nanocomposite silicon carbonitride thin film deposited by RF magnetron sputtering at different substrate temperatures
Authors:
A. S. Bhattacharyya,
S. K. Mishra
Abstract:
Raman studies of nanocomposite SiCN thin film by sputtering showed that with an increase of substrate temperature from room temperature to 500oC, a transition from mostly sp2 graphitic phase to sp3 carbon took place which was observed from the variation of ID/IG ratio and the peak shifts. This process resulted in the growth of C3N4 and Si3N4 crystallites in the amorphous matrix which led to an inc…
▽ More
Raman studies of nanocomposite SiCN thin film by sputtering showed that with an increase of substrate temperature from room temperature to 500oC, a transition from mostly sp2 graphitic phase to sp3 carbon took place which was observed from the variation of ID/IG ratio and the peak shifts. This process resulted in the growth of C3N4 and Si3N4 crystallites in the amorphous matrix which led to an increase in hardness and modulus obtained through nanoindentation. However, at a further higher temperature of 600oC, again an increase of sp2 C concentration in the film was observed and the H and E values showed a decrease due to increased growth of graphitic carbon phase. The whole process got reflected in a modified four stage Ferrari Robertson model of Raman spectroscopy.
△ Less
Submitted 17 November, 2016;
originally announced November 2016.
-
Thin Film growth of Solid State materials
Authors:
A. S Bhattacharyya,
P. Prabhakar,
R. P. Kumar,
S. Sharma,
S. K. Raj,
R. Ratn,
P. Kommu
Abstract:
Magnetron sputtering has also been used to deposit thin films of some materials and it has significant technological importance. A modeling on deposition of epitaxial thin films of Yttrium Stabilized Zirconia (YSZ) was done the diffusion of adatom on the surface were studies. There exists a strong interaction of ions formed in the plasma during the sputtering process. Cu thin films were deposited…
▽ More
Magnetron sputtering has also been used to deposit thin films of some materials and it has significant technological importance. A modeling on deposition of epitaxial thin films of Yttrium Stabilized Zirconia (YSZ) was done the diffusion of adatom on the surface were studies. There exists a strong interaction of ions formed in the plasma during the sputtering process. Cu thin films were deposited on Si. Nanocomposite thin film of SiCN showed dendritic growth.
△ Less
Submitted 17 November, 2016;
originally announced November 2016.
-
Nanocomposite si-c-n coatings
Authors:
A. S. Bhattacharyya
Abstract:
Coatings of ternary nanocomposite Si-C-N ceramic coatings have shown newer and improved mechanical and functional properties over the coarser and monolithic coatings. Properties like high hardness, wear resistance, oxidation resistance, tunable band gap and chemical inertness have been observed for Si-C-N which makes its potential for numerous applications. Although lot of research has taken place…
▽ More
Coatings of ternary nanocomposite Si-C-N ceramic coatings have shown newer and improved mechanical and functional properties over the coarser and monolithic coatings. Properties like high hardness, wear resistance, oxidation resistance, tunable band gap and chemical inertness have been observed for Si-C-N which makes its potential for numerous applications. Although lot of research has taken place in Si-C-N coatings, proper understanding of the effect of different parameters on the coating properties are still not resolved. The changes occurring in fraction of Si, C and N and the phases forming in the coatings with variation in deposition conditions require investigations. This research paper gives a systematic study of the role of different deposition parameters like substrate temperature, pressure, power on the nucleation and growth, structure, microstructural bonding and mechanical properties of the film deposited by magnetron sputtering which adds significantly to the fundamental knowledge of nanocomposite Si-C-N coatings as well as its applications.
△ Less
Submitted 17 August, 2016;
originally announced August 2016.
-
Ion Beam radiation and temperature effect on Co/Si and CoO/Co/Si thin films
Authors:
A. S. Bhattacharyya
Abstract:
Co and CoO thin films were deposited by magnetron sputtering in the form of multilayers. They were irradiated with Ar and Si ion beams of different energies and fluences. The magnetic properties were investigated.
Co and CoO thin films were deposited by magnetron sputtering in the form of multilayers. They were irradiated with Ar and Si ion beams of different energies and fluences. The magnetic properties were investigated.
△ Less
Submitted 18 August, 2016;
originally announced August 2016.
-
Composites of FeCl3 and TiO2 with Bismaleimide resins
Authors:
A. S. Bhattacharyya,
Nitesh Rajak,
Abhishek Sharma,
P. Kommu
Abstract:
Ferric Chloride-Bismaleimide (FeCl3-BMI) and Titania-Bismaleimide (TiO2-BMI) composite were synthesized using PVA as a binder. The composite systems were deposited on glass slide as a homogenous coating. XRD and FTIR studies of the composite system showed its crystalline and structural configuration. A mixed phase of TiO2 and BMI as well as short range crystallinity was observed. An increase in cr…
▽ More
Ferric Chloride-Bismaleimide (FeCl3-BMI) and Titania-Bismaleimide (TiO2-BMI) composite were synthesized using PVA as a binder. The composite systems were deposited on glass slide as a homogenous coating. XRD and FTIR studies of the composite system showed its crystalline and structural configuration. A mixed phase of TiO2 and BMI as well as short range crystallinity was observed. An increase in crystallinity with temperature was also seen. The percentage of N-H symmetric stretching was also found to increase with temperature.
△ Less
Submitted 4 August, 2016;
originally announced August 2016.
-
Indentation of Coatings at micro/nano scale: Crack formation and deflection
Authors:
A. S. Bhattacharyya
Abstract:
Nanoindentation is an effective way of finding mechanical properties at nanoscale. They are especially useful for thin films where elimination of the substrate effect is required. The mechanism is based upon depth sensing indentation based on Oliver and Pharr modeling. Nanoindentation was used to evaluate the nanomechanical and fractographic properties of hard coatings deposited by magnetron sputt…
▽ More
Nanoindentation is an effective way of finding mechanical properties at nanoscale. They are especially useful for thin films where elimination of the substrate effect is required. The mechanism is based upon depth sensing indentation based on Oliver and Pharr modeling. Nanoindentation was used to evaluate the nanomechanical and fractographic properties of hard coatings deposited by magnetron sputtering. Radial and lateral cracks accompanied by delamination of the coatings were observed during the indentation tests. A novel phenomenon of stress induced crystallization was observed in case of the CNx films which resulted in crack deflection. Indentations at micro scale using Vickers Indenter were also done and the cracking phenomena were analyzed.
△ Less
Submitted 21 July, 2016;
originally announced July 2016.
-
Structural characterization of APPJ treated Bismaleimide coatings and heat treated Titania-BMI
Authors:
S. Shrinidhi,
S. Suman,
A. Shah,
P. Prabhakar,
A. Chaurasia A. Kumar,
K. G. Chauhan,
A. S. Bhattacharyya
Abstract:
Bismaleimide (BMI) are thermosetting polymers mainly used in aerospace applications having properties of dimensional stability, low shrinkage, chemical resistance, fire resistance, good mechanical properties and high resistance against various solvents, acids, and water. BMI is commercially available as Homide 250. BMI coating has also been used for the corrosion protection. Metallization (AL) of…
▽ More
Bismaleimide (BMI) are thermosetting polymers mainly used in aerospace applications having properties of dimensional stability, low shrinkage, chemical resistance, fire resistance, good mechanical properties and high resistance against various solvents, acids, and water. BMI is commercially available as Homide 250. BMI coating has also been used for the corrosion protection. Metallization (AL) of BMI using vacuum evaporation was done which serves the purpose of prevention of space charge accumulation in aircraft bodies. Addition of inorganic materials like metal oxides can influence the properties of the polymer as an inorganic-organic composite. The organic-ionorganic composites have wide applications in electronics, optics, chemistry and medicine. Titanium dioxide (TiO2, Titania) has a wide range of applications starting from photocatalysis, dye-sensitized solar cells to optical coatings and electronics. A BMI-TiO2 composite was prepared by chemical route. Atmospheric Plasma Jet (APPJ) using Helium gas was also treated on BMI. XRD and FTIR studies of the composite system prepared at different temperatures showed its crystalline and structural configuration.
△ Less
Submitted 6 April, 2016;
originally announced April 2016.
-
Some aspects of epitaxial thin film growth
Authors:
A. S. Bhattacharyya,
Rishdeo Kumar,
Vikrant Raj,
S. Shrinidhi,
Shrishti Suman,
Asmita Shah,
Ramgiri P. Kumar
Abstract:
The article consists of four sections all dealing with the computational modeling of the sputtering process. The first section deals with the difference in Bismuth atomic layer deposition at different polar angle and ion flounce. In the second section, atomic layer deposition was studied as a function of incident Argon ion energy at different pressure conditions. A curve analogous to Bragg curve w…
▽ More
The article consists of four sections all dealing with the computational modeling of the sputtering process. The first section deals with the difference in Bismuth atomic layer deposition at different polar angle and ion flounce. In the second section, atomic layer deposition was studied as a function of incident Argon ion energy at different pressure conditions. A curve analogous to Bragg curve was obtained .In the third section TiOx films was developed by simulations. The sputtering parameters were varied to get different atomic layers. The variation of coverage with sticking coefficient was shown. The last section deals with sputter based deposition of TiN films. The rate of change of partial sputtering yield with coverage was considered. The deposition pressure and time were varied to get films of different thickness. All the sections are stored separately
△ Less
Submitted 6 April, 2016;
originally announced April 2016.
-
Substrate effect and nanoindentation fracture toughness based on pile up and failure
Authors:
Arnab S. Bhattacharyya,
R. Praveen Kumar,
Rohit Mandal,
Nikhil Kumar,
N. Rajak,
Abhishek Sharma,
Shashi Kant
Abstract:
The effect of substrate was studied using nanoindentation on thin films. Soft films on hard substrate showed more pile up than usual which was attributed to the dislocation pile up at the film substrate interface. The effect of tip blunting on the load depth and hardness plots of nanoindentation was shown. The experimental date of variation of Vickers hardness with film thickness and loads were fi…
▽ More
The effect of substrate was studied using nanoindentation on thin films. Soft films on hard substrate showed more pile up than usual which was attributed to the dislocation pile up at the film substrate interface. The effect of tip blunting on the load depth and hardness plots of nanoindentation was shown. The experimental date of variation of Vickers hardness with film thickness and loads were fitted and new parameters were analyzed. The delaminated area was analyzed using geometrical shapes using optical view of the failure region along with the load displacement Indentation fracture using Nanoindentation using Berkovich indenter has been studied. Indentation fracture toughness (KR) was analyzed based on computational programs. The contact mechanics during nanoindentation was studied with parameters related to indenter shape and tip sharpness. Elastic, plastic and total energies were computationally determined. The energy difference was related to shear stress being generated with elastic to plastic transition. Change in the nature of residual stress was related to film thickness.
△ Less
Submitted 19 June, 2016; v1 submitted 23 February, 2016;
originally announced February 2016.
-
Surface and Mechanical studies of Bismaleimide coatings
Authors:
A. S. Bhattacharyya,
D. Paul,
P. P. Dutta,
G. Bhattacharjee
Abstract:
Bismaleimide (BMI) resins are a new breed of thermosetting resins used mainly for high temperature applications and have major usage in aerospace. BMI polymer coatings were deposited on aluminum and mild steel substrates. The effect of corrosion on mild steel and aluminum by Ringers Solution and there protection using BMI coatings were observed. X-ray diffraction studies showed crystalline nature…
▽ More
Bismaleimide (BMI) resins are a new breed of thermosetting resins used mainly for high temperature applications and have major usage in aerospace. BMI polymer coatings were deposited on aluminum and mild steel substrates. The effect of corrosion on mild steel and aluminum by Ringers Solution and there protection using BMI coatings were observed. X-ray diffraction studies showed crystalline nature of the BMI coatings. Surface contact angle measurements were carried out using goniometer.
△ Less
Submitted 3 September, 2015;
originally announced September 2015.
-
Metallization and APPJ treatment of Bismaleimide
Authors:
A. S. Bhattacharyya,
S. Kumar,
A. Sharma,
D. Kumar,
S. B. Patel,
D. Paul,
P. P. Dutta,
G. Bhattacharjee
Abstract:
Bismaleimide (BMI) resins are a new breed of thermosetting resins used mainly for high temperature applications and have major usage in aerospace. FTIR studies have shown the signatures of imide, CNC stretching, malemide and N-H stretching. These BMI polymer coatings were deposited on aluminum and mild steel substrates by sprinkling powers followed by baking. Thermo gravimetric analysis and Differ…
▽ More
Bismaleimide (BMI) resins are a new breed of thermosetting resins used mainly for high temperature applications and have major usage in aerospace. FTIR studies have shown the signatures of imide, CNC stretching, malemide and N-H stretching. These BMI polymer coatings were deposited on aluminum and mild steel substrates by sprinkling powers followed by baking. Thermo gravimetric analysis and Differential scanning calorimetric studies showed the degradation temperature of these polymers around 370oC. Aluminum coatings were deposited on BMI previously deposited on Al and mild steel to make a metal-BMI-metal trilayer. These trilayers can solve the problem charging of the aircraft bodies at high altitudes. Atomic force microscopy was done to determine the morphology of the surface. Roughness and thickness measurements of the BMI coatings were carried out by surface profilometer. Vickers microhardness tests showed an increase in hardness of the metal-BMI-metal trilayer. FTIR spectrum showed signature of imides, CNC stretching, maleimide and N-H stretching in BMI. We observed that peak broadens at which shows the release of the stress during thermal treatment of the coating. The coating is subject to variable APPJ conditions which improve the properties at high temperature.
△ Less
Submitted 29 June, 2016; v1 submitted 20 August, 2015;
originally announced August 2015.
-
Sputtering based epitaxial growth and modeling of Cu/Si thin films
Authors:
A. S. Bhattacharyya,
S. Kumar,
S. Jana,
P. Y. Kommu,
K. Gaurav,
S. Prabha,
V. S. Kujur,
P. Bharadwaj
Abstract:
Epitaxial copper thin films were deposited by magnetron sputtering. The adatoms during deposition are influenced by deposition parameters which cause variations in thin film properties. XRD and FESEM studies were done to get an insight into the growth mechanisms of the films. A modeling has been done on the epitaxial thin film growth with sputtering process. The parameters during sputtering like,…
▽ More
Epitaxial copper thin films were deposited by magnetron sputtering. The adatoms during deposition are influenced by deposition parameters which cause variations in thin film properties. XRD and FESEM studies were done to get an insight into the growth mechanisms of the films. A modeling has been done on the epitaxial thin film growth with sputtering process. The parameters during sputtering like, sputtering yield, pressure, temperature, current density, deposition time were related and an attempt has been made to analyze the sputtering process.
△ Less
Submitted 20 August, 2015;
originally announced August 2015.
