Showing 1–50 of 57 results for author: Beaulieu, L

Non-negative Matrix Factorization using Partial Prior Knowledge for Radiation Dosimetry

Authors: Boby Lessard, Frédéric Marcotte, Arthur Lalonde, François Therriault-Proulx, Simon Lambert-Girard, Luc Beaulieu, Louis Archambault

Abstract: Hyperspectral unmixing aims at decomposing a given signal into its spectral signatures and its associated fractional abundances. To improve the accuracy of this decomposition, algorithms have included different assumptions depending on the application. The goal of this study is to develop a new unmixing algorithm that can be applied for the calibration of multi-point scintillation dosimeters used… ▽ More Hyperspectral unmixing aims at decomposing a given signal into its spectral signatures and its associated fractional abundances. To improve the accuracy of this decomposition, algorithms have included different assumptions depending on the application. The goal of this study is to develop a new unmixing algorithm that can be applied for the calibration of multi-point scintillation dosimeters used in the field of radiation therapy. This new algorithm is based on a non-negative matrix factorization. It incorporates a partial prior knowledge on both the abundances and the endmembers of a given signal. It is shown herein that, following a precise calibration routine, it is possible to use partial prior information about the fractional abundances, as well as on the endmembers, in order to perform a simplified yet precise calibration of these dosimeters. Validation and characterization of this algorithm is made using both simulations and experiments. The experimental validation shows an improvement in accuracy compared to previous algorithms with a mean spectral angle distance (SAD) on the estimated endmembers of 0.0766, leading to an average error of $(0.25 \pm 0.73)$ % on dose measurements. △ Less

Submitted 14 June, 2024; v1 submitted 17 September, 2023; originally announced September 2023.

Comments: 12 pages, 6 figures

Image registration of an electromagnetic tracking enabled afterloader and CT using a phantom for the quality control of implant reconstruction

Authors: Isaac Neri Gomez-Sarmiento, Daline Tho, Christopher Dürrbeck, Wim de Jager, Denis Laurendeau, Luc Beaulieu

Abstract: Electromagnetic tracking (EMT) shows great potential for automating implant reconstruction in brachytherapy. One of the challenges of this technology is that it does not intrinsically share the same reference frame as the patient's medical imaging. The purpose of this work is to register the reference frames of an EMT-enabled afterloader and a CT scan image of a rigid phantom for quality control o… ▽ More Electromagnetic tracking (EMT) shows great potential for automating implant reconstruction in brachytherapy. One of the challenges of this technology is that it does not intrinsically share the same reference frame as the patient's medical imaging. The purpose of this work is to register the reference frames of an EMT-enabled afterloader and a CT scan image of a rigid phantom for quality control of EMT-based implant reconstruction. The geometry of twelve 6F catheters and a tandem and ring gynecological applicator were reconstructed using an EMT sensor attached to an afterloader's check cable. All EMT reconstructions were done in three different environments: disturbance free, CT-on-rails brachytherapy suite and MRI brachytherapy suite. Implants were reconstructed using two acquisition methods: step-and-record and continuous motion. A CT scan of the phantom was obtained and manually reconstructed in the treatment planning system, with the help of the solid model of the applicator. Rigid registration algorithms were used to register EMT and CT scan reference frames using corresponding points from the EMT and CT based reconstructions of the phantom, following three approaches: one gynecological applicator, four catheters inside four calibration plates having and S-shaped path, and four ceramic marbles within the calibration plates. The absolute median deviation from the expected value for EMT measurements in all three environments significantly lie below the sensor's expected accuracy of 0.70 mm (p < 0.001), suggesting that the environment did not have a significant impact on the measurements, given that care is taken in the immediate surroundings. In all three environments, the two acquisition and three registration approaches have a mean and median registration errors (perpendicular distance) that lie at or below 1 mm, which is lower than the clinical acceptable threshold of 2 mm. △ Less

Submitted 3 August, 2023; originally announced August 2023.

Glamour muscles: why having a body is not what it means to be embodied

Authors: Shawn L. Beaulieu, Sam Kriegman

Abstract: Embodiment has recently enjoyed renewed consideration as a means to amplify the faculties of smart machines. Proponents of embodiment seem to imply that optimizing for movement in physical space promotes something more than the acquisition of niche capabilities for solving problems in physical space. However, there is nothing in principle which should so distinguish the problem of action selection… ▽ More Embodiment has recently enjoyed renewed consideration as a means to amplify the faculties of smart machines. Proponents of embodiment seem to imply that optimizing for movement in physical space promotes something more than the acquisition of niche capabilities for solving problems in physical space. However, there is nothing in principle which should so distinguish the problem of action selection in physical space from the problem of action selection in more abstract spaces, like that of language. Rather, what makes embodiment persuasive as a means toward higher intelligence is that it promises to capture, but does not actually realize, contingent facts about certain bodies (living intelligence) and the patterns of activity associated with them. These include an active resistance to annihilation and revisable constraints on the processes that make the world intelligible. To be theoretically or practically useful beyond the creation of niche tools, we argue that "embodiment" cannot be the trivial fact of a body, nor its movement through space, but the perpetual negotiation of the function, design, and integrity of that body$\unicode{x2013}$that is, to participate in what it means to $\textit{constitute}$ a given body. It follows that computer programs which are strictly incapable of traversing physical space might, under the right conditions, be more embodied than a walking, talking robot. △ Less

Submitted 17 July, 2023; originally announced July 2023.

Hybrid Cerenkov-scintillation detector validation using Monte Carlo simulations

Authors: Emilie Jean, Simon Lambert-Girard, Francois Therriault-Proulx, Luc Beaulieu

Abstract: Objective: This study aimed at investigating through Monte Carlo simulations the limitations of a novel hybrid Cerenkov-scintillation detector and the associated method for irradiation angle measurements. Approach: Using Monte Carlo simulations, previous experimental irradiations of the hybrid detector with a linear accelerator were replicated to evaluate its general performances and limitations.… ▽ More Objective: This study aimed at investigating through Monte Carlo simulations the limitations of a novel hybrid Cerenkov-scintillation detector and the associated method for irradiation angle measurements. Approach: Using Monte Carlo simulations, previous experimental irradiations of the hybrid detector with a linear accelerator were replicated to evaluate its general performances and limitations. Cerenkov angular calibration curves and irradiation angle measurements were then compared. Furthermore, the impact of the Cerenkov light energy dependency on the detector accuracy was investigated using the energy spectra of electrons travelling through the detector. Main results: Monte Carlo simulations were found to be in good agreement with experimental values. The irradiation angle absolute mean error was found to be lesser than what was obtained experimentally, with a maximum value of 1.12 degree for the 9 MeV beam. A 0.4% increase of the ratio of electrons having an energy below 1 MeV to the total electrons was found to impact the Cerenkov light intensity collected as a function of the incident angle. The effect of the Cerenkov intensity variation on the measured angle was determined to vary according to the slope of the angular calibration curve. While the contribution of scattered electrons with a lower energy affects the detector accuracy, greatest discrepancies result from the limitations of the calculation method and the calibration curve itself. Significance: A precise knowledge of the limitations of the hybrid detector and the irradiation angle calculation method is crucial for a clinical implementation. Moreover, the simulations performed in this study also corroborates hypotheses made regarding the relations between multiple Cerenkov dependencies and observations from the experimental measurements. △ Less

Submitted 22 March, 2022; originally announced March 2022.

Technical note: On the use of polychromatic cameras for high spatial resolution spectral dose measurements

Authors: Emily Cloutier, Luc Beaulieu, Louis Archambault

Abstract: Despite the demonstrated benefits of hyperspectral formalism for stem effect corrections in the context of fiber dose measurements, this approach has not been yet translated into volumetric measurements where cameras are typically used for their distinguishing spatial resolution. This work investigates demosaicing algorithms for polychromatic cameras based spectral imaging. The scintillation and C… ▽ More Despite the demonstrated benefits of hyperspectral formalism for stem effect corrections in the context of fiber dose measurements, this approach has not been yet translated into volumetric measurements where cameras are typically used for their distinguishing spatial resolution. This work investigates demosaicing algorithms for polychromatic cameras based spectral imaging. The scintillation and Cherenkov signals produced in a radioluminescent phantom are imaged by a polychromatic camera and isolated using the spectral formalism. To do so, five demosaicing algorithms are investigated from calibration to measurements: a clustering method and four interpolation algorithms. The resulting accuracy of scintillation and Cherenkov images is evaluated with measurements of the differences (mean $\pm$ standard deviation) between the obtained and expected signals from profiles drawn across a scintillation spot. Signal-to-noise ratio and signal-to-background ratio are further measured and compared in the resulting scintillation images. Clustering, OpenCV, bilinear, Malvar and Menon demosaicing algorithms respectively yielded differences of $3\pm6\%$, $0.1\pm0.5\%$, $0.5\pm0.5\%$, $1\pm3\%$ and $1\pm4\%$ in the resulting scintillation images. For the Cherenkov images, all algorithms provided differences below 1\%. All methods enabled measurements over the detectability (SBR>2) and sensitivity (SNR>5) thresholds with the bilinear algorithm providing the best SNR value. Hence, radioluminescent signals can accurately be isolated using a single polychromatic camera. Moreover, demosaicing using a bilinear kernel provided the best results and enabled stem effect subtraction while preserving the full spatial resolution of the camera. △ Less

Submitted 30 November, 2021; originally announced December 2021.

External beam irradiation angle measurement using Cerenkov emission

Authors: Emilie Jean, Simon Lambert-Girard, Francois Therriault-Proulx, Luc Beaulieu

Abstract: Due to its angular dependency, Cerenkov light has long been considered a contamination signal in plastic scintillating dosimeters. In this study, we propose a novel approach designed to take advantage of this angular dependency to perform a direct measurement of an external beam radiation angle of incidence. A Cerenkov probe composed of a 10-mm long filtered sensitive volume of clear PMMA optical… ▽ More Due to its angular dependency, Cerenkov light has long been considered a contamination signal in plastic scintillating dosimeters. In this study, we propose a novel approach designed to take advantage of this angular dependency to perform a direct measurement of an external beam radiation angle of incidence. A Cerenkov probe composed of a 10-mm long filtered sensitive volume of clear PMMA optical fibre was built. Both filtered and raw Cerenkov signals from the transport fibre were collected through a single 1-mm diameter transport fibre. An independent PSD composed of 10-mm BCF12 scintillating fibre was also used for simultaneous dose measurements. A first series of measurements aimed at validating the ability to account for the Cerenkov electron energy spectrum dependency by simultaneously measuring the deposited dose. A cylindrical phantom was then used to obtain an angular calibration curve for fixed dose irradiations and perform incident angle measurements using electron and photon beams. The beam nominal energy was found to have a significant impact on the shapes of the angular calibration curves obtained for irradiation angle measurements. This can be linked to the electron energy spectrum dependency of the Cerenkov emission cone. Irradiation angle measurements exhibit an absolute mean error of 1.86° and 1.02° at 6 and 18 MV, respectively. Similar results were obtained with electron beams and the absolute mean error reaches 1.97, 1.66, 1.45 and 0.95 degrees at 9, 12, 16 and 20 MeV, respectively. Reducing the numerical aperture of the Cerenkov probe leads to an increased angular dependency for the lowest energy while no major changes were observed at higher energy. This allowed irradiation angle measurements at 6 MeV with a mean absolute error of 4.82°. The detector offers promising perspectives for external beam radiotherapy and brachytherapy applications. △ Less

Submitted 16 March, 2022; v1 submitted 22 November, 2021; originally announced November 2021.

External beam irradiation angle measurement using Cerenkov emission I: Signal dependencies consideration

Authors: Emilie Jean, Simon Lambert-Girard, Francois Therriault-Proulx, Luc Beaulieu

Abstract: This study introduces a novel hybrid Cerenkov-scintillation dosimeter which is intended to be used for irradiation angle measurements based on the Cerenkov angular dependency. First measurements aimed at validating the ability to account for the Cerenkov electron energy spectrum dependency by simultaneously measuring the deposited dose, thus isolating signal variations resulting from the angular d… ▽ More This study introduces a novel hybrid Cerenkov-scintillation dosimeter which is intended to be used for irradiation angle measurements based on the Cerenkov angular dependency. First measurements aimed at validating the ability to account for the Cerenkov electron energy spectrum dependency by simultaneously measuring the deposited dose, thus isolating signal variations resulting from the angular dependency. The Cerenkov probe is composed of a 10-mm long sensitive volume of clear PMMA optical fiber separated by an absorptive filter from a 1-mm diameter transport fiber. Filtered and raw Cerenkov signals from the sensitive volume and transport fiber, respectively, were collected using the Hyperscint RP-200 scintillation dosimetry platform. The total signal was unmixed using a hyperspectral approach. Dose calibration of the detector signal was accomplished with photon and electron beams. Using a solid-water phantom, measurements at fixed incident angles covering a wide range of doses and output factors were realized. For fixed incident angle, signal characterization of the Cerenkov detector displays a linear dose-light relationship. As expected, the sensitive volume signal was found to be energy dependent. Output factors were accurately measured within 0.8 % for field size up to 25 cm x 25 cm with both photons and electrons. First validation of the Cerenkov angular dependency shows a linear dose-light relationship for the whole range of angles tested. As expected, the Cerenkov signal intensity per dose unit varies based on the irradiation angle due to the angular dependency. Results showed that using calibration conditions where the electron energy spectrum is similar to the measurement conditions allows to rely on deposited dose to account for this dependency. These preliminary results constitute a first step toward experimental irradiation angle measurements. △ Less

Submitted 26 January, 2022; v1 submitted 22 November, 2021; originally announced November 2021.

Comments: The two-part study was merged in a single paper as requested by the editor of the journal. Findings of both papers can now be found in the updated version of the second part "External beam irradiation angle measurement using Cerenkov emission"

Continual learning under domain transfer with sparse synaptic bursting

Authors: Shawn L. Beaulieu, Jeff Clune, Nick Cheney

Abstract: Existing machines are functionally specific tools that were made for easy prediction and control. Tomorrow's machines may be closer to biological systems in their mutability, resilience, and autonomy. But first they must be capable of learning and retaining new information without being exposed to it arbitrarily often. Past efforts to engineer such systems have sought to build or regulate artifici… ▽ More Existing machines are functionally specific tools that were made for easy prediction and control. Tomorrow's machines may be closer to biological systems in their mutability, resilience, and autonomy. But first they must be capable of learning and retaining new information without being exposed to it arbitrarily often. Past efforts to engineer such systems have sought to build or regulate artificial neural networks using disjoint sets of weights that are uniquely sensitive to specific tasks or inputs. This has not yet enabled continual learning over long sequences of previously unseen data without corrupting existing knowledge: a problem known as catastrophic forgetting. In this paper, we introduce a system that can learn sequentially over previously unseen datasets (ImageNet, CIFAR-100) with little forgetting over time. This is done by controlling the activity of weights in a convolutional neural network on the basis of inputs using top-down regulation generated by a second feed-forward neural network. We find that our method learns continually under domain transfer with sparse bursts of activity in weights that are recycled across tasks, rather than by maintaining task-specific modules. Sparse synaptic bursting is found to balance activity and suppression such that new functions can be learned without corrupting extant knowledge, thus mirroring the balance of order and disorder in systems at the edge of chaos. This behavior emerges during a prior pre-training (or 'meta-learning') phase in which regulated synapses are selectively disinhibited, or grown, from an initial state of uniform suppression through prediction error minimization. △ Less

Submitted 16 January, 2024; v1 submitted 26 August, 2021; originally announced August 2021.

Accurate Dose Measurements Using Cherenkov Polarization Imaging

Authors: Emily Cloutier, Louis Archambault, Luc Beaulieu

Abstract: Purpose: Cherenkov radiation carries the potential of direct in-water dose measurements, but its precision is currently limited by a strong anisotropy. Taking advantage of polarization imaging, this work proposes a new approach for high accuracy Cherenkov dose measurements. Methods: Cherenkov produced in a 15x15x20 cm^3 water tank is imaged with a cooled CCD camera from four polarizer transmission… ▽ More Purpose: Cherenkov radiation carries the potential of direct in-water dose measurements, but its precision is currently limited by a strong anisotropy. Taking advantage of polarization imaging, this work proposes a new approach for high accuracy Cherenkov dose measurements. Methods: Cherenkov produced in a 15x15x20 cm^3 water tank is imaged with a cooled CCD camera from four polarizer transmission axes [0°, 45°, 90°, 135°]. The water tank is positioned at the isocenter of a 5x5 cm^2, 6 MV photon beam. Using Malus' law, the polarized portion of the signal is extracted. Corrections are applied to the polarized signal following azimuthal and polar Cherenkov angular distributions extracted from Monte Carlo simulations. Percent depth dose and beam profiles are measured and compared with the prediction from a treatment planning system (TPS). Results: Corrected polarized signals on the central axis reduced deviations at depth from 20% to 0.8\pm1%. For the profile measurement, differences between the corrected polarized signal and the TPS calculations are 1\pm3% and 8\pm3% on the central axis and penumbra regions respectively. 29\pm1% of the Cherenkov signal was found to be polarized. Conclusions: This work proposes a novel polarization imaging approach enabling high precision water-based Cherenkov dose measurements. The method allows correction of the Cherenkov anisotropy within 3% on the beam central axis and in depth. △ Less

Submitted 15 June, 2021; originally announced June 2021.

Performance of an Enhanced Afterloader with Electromagnetic Tracking Capabilities for Channel Reconstruction and Error Detection

Authors: Daline Tho, Marie-Claude Lavallée, Luc Beaulieu

Abstract: The reconstruction and error detection performance of a Flexitron research unit equipped with a special check-cable in which is integrated an EM sensor (NDI Aurora V3) that enables tracking and reconstruction capability was assessed. Reconstructions of a 24 cm long catheter were performed using two methods: continuous fixed speed check cable backward step** and step** through each dwell positi… ▽ More The reconstruction and error detection performance of a Flexitron research unit equipped with a special check-cable in which is integrated an EM sensor (NDI Aurora V3) that enables tracking and reconstruction capability was assessed. Reconstructions of a 24 cm long catheter were performed using two methods: continuous fixed speed check cable backward step** and step** through each dwell position every 1mm. The ability of the system to differentiate between two closely located (parallel) catheters was investigated by connecting catheters to the afterloader and moving it from its axis with an increment of 1mm. A robotic arm was used to move the catheter between each reconstruction. Reconstructions were obtained with a locally weighted scatter-plot smoothing algorithm. To quantify the reconstruction accuracy, distances between two catheters were computed along the reconstruction track with a 5mm step. Reconstructions of curve catheter paths were assessed through parallel and perpendicular phantom configuration to the EM field generator. Indexer length and lateral error were simulated and ROC analysis was made. Using a 50cm/s check cable speed does not allow accurate reconstruction. A slower check cable speed results in better reconstruction performance and smaller standard deviations. The optimum operating distance from the field generator (50-300mm) resulted in a lower absolute mean deviation from the expected value (0.2pm0.1mm) versus being positioned on the edge of the electromagnetic sensitive detection volume (0.6pm0.3mm). Reconstructions of curved and circular paths with a check cable speed under 5cm/s gave a 0.8pm0.5mm error, or better. All indexer and lateral shifts of 1mm were detected with a check cable speed of 2.5cm/s or under. A speed under 5cm/s is recommended for straight and curved catheter reconstructions. The check cable can also be used to detect common shift errors. △ Less

Submitted 12 May, 2021; originally announced May 2021.

Deformable Scintillation Dosimeter II: Real-Time Simultaneous Measurements of Dose and Tracking of Deformation Vector Fields

Authors: Emily Cloutier, Luc Beaulieu, Louis Archambault

Abstract: Anatomical motion and deformation pose challenges to the understanding of the delivered dose distribution during radiotherapy treatments. Hence, deformable image registration (DIR) algorithms are increasingly used to map contours and dose distributions from one image set to another. However, the lack of validation tools slows their clinical adoption, despite their commercial availability. This wor… ▽ More Anatomical motion and deformation pose challenges to the understanding of the delivered dose distribution during radiotherapy treatments. Hence, deformable image registration (DIR) algorithms are increasingly used to map contours and dose distributions from one image set to another. However, the lack of validation tools slows their clinical adoption, despite their commercial availability. This work presents a novel water-equivalent deformable dosimeter that simultaneously measures the dose distribution and tracks deformation vector fields (DVF). The dosimeter in made of an array of 19 scintillating fiber detectors embedded in a cylindrical elastomer matrix. It is imaged by two pairs of stereoscopic cameras tracking the position and angulation of the scintillators, while measuring the dose. The resulting system provides a precision of 0.3 mm on DVF measurements. The dosimeter was irradiated with 5$\times$3, 4$\times$3 and 3$\times$3 cm$^2$ 6 MV photon beams in both fixed and deformed conditions. The measured DVF was compared to the one computed with a DIR algorithm (Plastimatch). The deviations between the computed and measured DVFs was below 1.5 mm. As for dose measurements, the dosimeter acquired the dose distribution in fixed and deformed conditions within 1\% of the treatment planning system calculation and complementary dose validation using the Hyperscint dosimetry system. Using the demonstrated qualities of scintillating detectors, we developed a real-time, water-equivalent deformable dosimeter. Given it's sensor tracking position precision and dose measurements accuracy, the developed detector is a promising tools for the validation of DIR algorithms as well as dose distribution measurements under fixed and deformed conditions. △ Less

Submitted 21 January, 2021; originally announced January 2021.

Deformable Scintillation Dosimeter I: Challenges and Implementation using Computer Vision Techniques

Authors: Emily Cloutier, Louis Archambault, Luc Beaulieu

Abstract: Plastic scintillation detectors are increasingly used to measure dose distributions in the context of radiotherapy treatments. Their water-equivalence, real-time response and high spatial resolution distinguish them from traditional detectors, especially in complex irradiation geometries. Their range of applications could be further extended by embedding scintillators in a deformable matrix mimick… ▽ More Plastic scintillation detectors are increasingly used to measure dose distributions in the context of radiotherapy treatments. Their water-equivalence, real-time response and high spatial resolution distinguish them from traditional detectors, especially in complex irradiation geometries. Their range of applications could be further extended by embedding scintillators in a deformable matrix mimicking anatomical changes. In this work, we characterized signal variations arising from the translation and rotation of scintillating fibers with respect to a camera. Corrections are proposed using stereo vision techniques and two sCMOS complementing a CCD camera. The study was extended to the case of a prototype real-time deformable dosimeter comprising an array of 19 scintillating. The signal to angle relationship follows a gaussian distribution (FWHM = 52°) whereas the intensity variation from radial displacement follows the inverse square law. Tracking the position and angle of the fibers enabled the correction of these spatial dependencies. The detecting system provides an accuracy and precision of respectively 0.008 cm and 0.03 cm on the position detection. This resulted in an uncertainty of 2° on the angle measurement. Displacing the dosimeter by $\pm$3 cm in depth resulted in relative intensities of 100$\pm$10% (mean $\pm$ standard deviation) to the reference position. Applying corrections reduced the variations thus resulting in relative intensities of 100$\pm$1%. Similarly, for lateral displacements of $\pm$3 cm, intensities went from 98$\pm$3% to 100$\pm$1% after the correction. Therefore, accurate correction of the signal collected by a camera imaging the output of scintillating elements in a 3D volume is possible. This work paves the way to the development of real-time scintillator-based deformable dosimeters. △ Less

Submitted 21 January, 2021; originally announced January 2021.

Comparative optic and dosimetric characterization of the HYPERSCINT scintillation dosimetry research platform for multipoint applications

Authors: Emilie Jean, Francois Therriault-Proulx, Luc Beaulieu

Abstract: This study introduces the HYPERSCINT research platform, the first commercially available scintillation dosimetry platform capable of multi-point dosimetry through the hyperspectral approach. Optic and dosimetric performances of the system were investigated through comparison with another commercially available solution, the Ocean Optics QE65Pro spectrometer. The optical characterization was accomp… ▽ More This study introduces the HYPERSCINT research platform, the first commercially available scintillation dosimetry platform capable of multi-point dosimetry through the hyperspectral approach. Optic and dosimetric performances of the system were investigated through comparison with another commercially available solution, the Ocean Optics QE65Pro spectrometer. The optical characterization was accomplished by measuring the linearity of the signal as a function of integration time, photon detection efficiency and spectral resolution for both systems. Dosimetric performances were then evaluated with a 3-point plastic scintillator detector (mPSD) in terms of signal to noise ratio (SNR) and signal to background ratio (SBR) associated with each scintillator. The latter were subsequently compared with those found in the literature for the Exradin W1, a single-point plastic scintillator detector. Finally, various beam measurements were realized with the HYPERSCINT platform to evaluate its ability to perform clinical photon beam dosimetry. Both systems were found to be comparable in terms of linearity of the signal as a function of the intensity. Although the QE65Pro possesses a higher spectral resolution, the detection efficency of the HYPERSCINT is up to 1000 time greater. Dosimetric measurements shows that the latter also offers a better SNR and SBR, surpassing even the SNR of the Exradin W1 single-point PSD. While the doses ranging from 1 cGy to 600 cGy were accurately measured within 2.1% of the predicted dose using the HYPERSCINT platform coupled to the mPSD, the Ocean optics spectrometer shows discrepencies up to 86% under 50cGy. Similarly, depth dose, full width at half maximum region of the beam profile and output factors were all accurately measured within 2.3% of the predicted dose using the HYPERSCINT platform and exhibit an average difference of 0.5%, 1.6% and 0.6%, respectively. △ Less

Submitted 22 March, 2021; v1 submitted 30 October, 2020; originally announced November 2020.

3D source tracking and error detection in HDR using two independent scintillator dosimetry systems

Authors: Haydee M. Linares Rosales, Jacob G. Johansen, Gustavo Kertzscher, Kari Tanderup, Luc Beaulieu, Sam Beddar

Abstract: The high dose gradients near the source characteristics of brachytherapy are equivalent to nefarious effects if unnoticed errors take place during the patient treatment. In vivo dosimetry is the only method to quantify the delivered dose. Previous studies to this one, have characterized potential detectors that can be used as in vivo dosimeter. Some of them have focused on the source tracking topi… ▽ More The high dose gradients near the source characteristics of brachytherapy are equivalent to nefarious effects if unnoticed errors take place during the patient treatment. In vivo dosimetry is the only method to quantify the delivered dose. Previous studies to this one, have characterized potential detectors that can be used as in vivo dosimeter. Some of them have focused on the source tracking topic in HDR brachytherapy. The aim of this study is to perform 3D source position reconstruction by combining in vivo dosimetry measurements from two independent detector systems. The first was based on multiple (three) plastic scintillator detectors and the second on a single inorganic crystal (CsI:Tl). By combining two detector responses, we enabled the determination of the absolute source coordinates in 3D space. The method in this study proposed can be extended to the combination of different systems. △ Less

Submitted 21 June, 2020; originally announced June 2020.

From conception to clinical trial: IViST -- the first multi-sensor-based platform for real-time In Vivo dosimetry and Source Tracking in HDR brachytherapy

Authors: Haydee M. Linares Rosales, Audrey Cantin, Sylviane Aubin, Sam Beddar, Luc Beaulieu

Abstract: This study aims to introduce IViST (In Vivo Source Tracking), a novel multi-sensors dosimetry platform for real-time treatment monitoring in HDR brachytherapy. IViST is a platform that comprises 3 parts: 1) an optimized and characterized multi-point plastic scintillator dosimeter (3 points mPSD; using BCF-60, BCF-12, and BCF-10 scintillators), 2) a compact assembly of photomultiplier tubes (PMTs)… ▽ More This study aims to introduce IViST (In Vivo Source Tracking), a novel multi-sensors dosimetry platform for real-time treatment monitoring in HDR brachytherapy. IViST is a platform that comprises 3 parts: 1) an optimized and characterized multi-point plastic scintillator dosimeter (3 points mPSD; using BCF-60, BCF-12, and BCF-10 scintillators), 2) a compact assembly of photomultiplier tubes (PMTs) coupled to dichroic mirrors and filters for high-sensitivity scintillation light collection, and 3) a Python-based graphical user interface used for system management and signal processing. IViST can simultaneously measure dose, triangulate source position, and measure dwell time. By making 100 000 measurements/s, IViST samples enough data to quickly perform key QA/QC tasks such as identifying wrong individual dwell time or interchanged transfer tubes. By using 3 co-linear sensors and planned information for an implant geometry (from DICOM RT), the platform can also triangulate source position in real-time. A clinical trial is presently on-going using the IViST system. △ Less

Submitted 14 June, 2020; originally announced June 2020.

Light-Generating CdSe/CdS Colloidal Quantum Dot-Doped Plastic Optical Fibers

Authors: Carly A. Whittaker, Arthur Perret, Charles W. Fortier, Olivier-Michel Tardif, Sébastien A. Lamarre, Steeve Morency, Dominic Larivière, Luc Beaulieu, Younès Messaddeq, Claudine Nì. Allen

Abstract: Colloidal quantum dots (cQDs) are now a mature nanomaterial with optical properties customizable through varying size and composition. However, their use in optical devices is limited as they are not widely available in convenient forms such as optical fibers. With advances in polymerization methods incorporating nanocrystals, nanocomposite materials suitable for processing into high quality hybri… ▽ More Colloidal quantum dots (cQDs) are now a mature nanomaterial with optical properties customizable through varying size and composition. However, their use in optical devices is limited as they are not widely available in convenient forms such as optical fibers. With advances in polymerization methods incorporating nanocrystals, nanocomposite materials suitable for processing into high quality hybrid active fibers can be achieved. We demonstrate a plastic optical fiber fabrication method which ensures homogeneous dispersion of cQDs within a polymer core matrix. Loading concentrations between 10$^{11}$-10$^{13}$ CdSe/CdS cQDs per cm$^{3}$ in polystyrene were electronically imaged, confirming only sporadic sub-wavelength aggregates. Rayleigh scattering losses are therefore dominant at energies below the semiconductors' band gap, but are overtaken by a sharp CdS-related absorption onset around 525 nm facilitating cQD excitation. The redshifted photoluminescence emission is then minimally reabsorbed along the fiber with a spectrum barely affected by the polymerization and a quantum yield staying at $\sim$65$\%$ of its initial value. The latter, along with the glass transition temperature and refractive index, is independent of the cQD concentration hence yielding a proportionally increasing light output. Our cQD-doped fibers are photostable to within 5$\%$ over days showing great promise for functional material applications. △ Less

Submitted 6 June, 2020; originally announced June 2020.

Comments: Submitted to ACS Applied Nano Materials

On the use of machine learning methods for mPSD calibration in HDR brachytherapy

Authors: Haydee M. Linares Rosales, Gabriel Couture, Louis Archambault, Sam Beddar, Philippe Despres, Luc Beaulieu

Abstract: Purpose: We sought to evaluate the feasibility of using machine learning algorithms for multipoint plastic scintillator detector calibration in high-dose-rate brachytherapy. Methods: The dosimetry system consisted of an optimized 1-mm-core mPSD and a compact assembly of photomultiplier tubes coupled with dichroic mirrors and filters. An $^{192}$Ir source was remotely controlled and sent to various… ▽ More Purpose: We sought to evaluate the feasibility of using machine learning algorithms for multipoint plastic scintillator detector calibration in high-dose-rate brachytherapy. Methods: The dosimetry system consisted of an optimized 1-mm-core mPSD and a compact assembly of photomultiplier tubes coupled with dichroic mirrors and filters. An $^{192}$Ir source was remotely controlled and sent to various positions in a homemade PMMA holder. Dose measurements covering a range of 0.5 to 12 cm of source displacement were carried out according to TG-43 recommendations. Individual scintillator doses were decoupled using a linear regression model, a random forest estimator, and artificial neural network algorithms. The performance of the different algorithms was evaluated using different sample sizes and distances to the source for the mPSD system calibration. Results: The decoupling methods' deviations from the expected TG-43 dose generally remained below 20%. However, the dose prediction with the three algorithms was accurate to within 7% relative to the dose predicted by the TG-43 formalism for measurements performed in the same range of distances used for calibration. The performance random forest was compromised when the predictions were done beyond the range of distances used for calibration. The dose prediction by the linear regression was less influenced by the calibration conditions than random forest, but with more significant deviations. The number of available measurements for training purposes influenced the random forest and neural network models the most. Their accuracy tended to converge toward deviation values close to 1% from a number of dwell positions greater than 100. Conclusions: In performing HDR brachytherapy dose measurements with an optimized mPSD system, ML algorithms are good alternatives for precise dose reporting and treatment assessment. △ Less

Submitted 1 May, 2020; originally announced May 2020.

Dosimetric performance of a multi-point plastic scintillator dosimeter as a tool for real-time source tracking in high dose rate brachytherapy

Authors: Haydee M. Linares Rosales, Louis Archambault, Sam Beddar, Luc Beaulieu

Abstract: Purpose: To present the performance of a multi-point plastic scintillation detector (mPSD) as a tool in vivo dosimetry in brachytherapy. Methods: A previously optimized three-point sensor system was used for in vivo HDR brachytherapy measurements (using the scintillators BCF-60, BCF-12, and BCF-10). The light detection system of the mPSD consisted of compactly assembled photomultiplier tubes (PMTs… ▽ More Purpose: To present the performance of a multi-point plastic scintillation detector (mPSD) as a tool in vivo dosimetry in brachytherapy. Methods: A previously optimized three-point sensor system was used for in vivo HDR brachytherapy measurements (using the scintillators BCF-60, BCF-12, and BCF-10). The light detection system of the mPSD consisted of compactly assembled photomultiplier tubes (PMTs) and dichroic mirrors and filters to achieve a highly sensitive scintillation light collection. The PMT signals were recorded using a NI-DAQ board at a rate of 100 kHz. Dose measurements covering a range of 0.5 to 10 cm from the 192Ir source were carried out according to TG-43 U1 recommendations in order to: (1) characterize the system's response in terms of angular dependence; (2) obtain the relative contribution of positioning and measurement uncertainties to the total system uncertainty; (3) assess the system's temporal resolution; and (4) track the source position in real time. Results: The positioning uncertainty dominated close to the source, whereas the measurement uncertainty dominated at larger distances. A maximum measurement uncertainty of 17 % was observed for the BCF-60 scintillator at 10 cm from the source. The average best compromise between positioning and measurement uncertainties were reached at 17.4 mm. The detector further exhibited no angular dependence. The system provided an average location with a standard deviation under 1.7 mm. The maximum observed differences between measured and expected source location was 1.82 mm. Dose deviations remained below 5% in all the explored measurement conditions. With regard to dwell time measurement accuracy, the maximum deviation observed at all distances was 0.56 s. Conclusions: The performance of the system demonstrated that it could be used for real-time dose, position and dwell time measurements during HDR brachytherapy. △ Less

Submitted 28 October, 2019; originally announced October 2019.

A GPU-based multi-criteria optimization algorithm for HDR brachytherapy

Authors: Cédric Bélanger, Songye Cui, Yunzhi Ma, Philippe Després, J. Adam M. Cunha, Luc Beaulieu

Abstract: Currently in HDR brachytherapy planning, a manual fine-tuning of an objective function is necessary to obtain case-specific valid plans. This study intends to facilitate this process by proposing a patient-specific inverse planning algorithm for HDR prostate brachytherapy: GPU-based multi-criteria optimization (gMCO). Two GPU-based optimization engines including simulated annealing (gSA) and a q… ▽ More Currently in HDR brachytherapy planning, a manual fine-tuning of an objective function is necessary to obtain case-specific valid plans. This study intends to facilitate this process by proposing a patient-specific inverse planning algorithm for HDR prostate brachytherapy: GPU-based multi-criteria optimization (gMCO). Two GPU-based optimization engines including simulated annealing (gSA) and a quasi-Newton optimizer (gL-BFGS) were implemented to compute multiple plans in parallel. After evaluating the equivalence and the computation performance of these two optimization engines, one preferred optimization engine was selected for the gMCO algorithm. Five hundred sixty-two previously treated prostate HDR cases were divided into validation set (100) and test set (462). In the validation set, the number of Pareto optimal plans to achieve the best plan quality was determined for the gMCO algorithm. In the test set, gMCO plans were compared with the physician-approved clinical plans. Over 462 cases, the number of clinically valid plans was 428 (92.6%) for clinical plans and 461 (99.8%) for gMCO plans. The number of valid plans with target V100 coverage greater than 95% was 288 (62.3%) for clinical plans and 414 (89.6%) for gMCO plans. The mean planning time was 9.4 s for the gMCO algorithm to generate 1000 Pareto optimal plans. In conclusion, gL-BFGS is able to compute thousands of SA equivalent treatment plans within a short time frame. Powered by gL-BFGS, an ultra-fast and robust multi-criteria optimization algorithm was implemented for HDR prostate brachytherapy. A large-scale comparison against physician approved clinical plans showed that treatment plan quality could be improved and planning time could be significantly reduced with the proposed gMCO algorithm. △ Less

Submitted 2 April, 2019; originally announced April 2019.

Comments: 18 pages, 7 figures

Technical Note: A Novel Electromagnetic-Tracked Scintillation Dosimeter for Accurate In Vivo Dosimetry in HDR Brachytherapy

Authors: Daline Tho, Luc Beaulieu

Abstract: Since large dose are administrated to the patient in brachytherapy treatment, ensuring the right dose is delivered is highly critical. This study presents a first step in solving the standing issue of accurately knowing the dosimeter position at all time during in vivo dosimetry. In this work, an energy independent dosimeter, namely plastic scintillation detector, is coupled to an electromagnetic… ▽ More Since large dose are administrated to the patient in brachytherapy treatment, ensuring the right dose is delivered is highly critical. This study presents a first step in solving the standing issue of accurately knowing the dosimeter position at all time during in vivo dosimetry. In this work, an energy independent dosimeter, namely plastic scintillation detector, is coupled to an electromagnetic (EM) sensor having sub-mm positional accuracy for real-time tracking of the dosimeter position. However, adding an EM sensor adds materials in the path to the scintillator and thus could potentially perturb the dose measurements.To confirm the perturbation presence, 4 different sensors were placed in front of the scintillator so the radiation does not arrive to it directly. Variation of the distance between the sensor and the scintillator was used to quantify the effect on the signal at 0° and 90°.To test the dependence for each sensor, the signal measurement were taken from 0° to 90° with 10$°$ increment. The 5PCBDOF sensor showed an increased signal of almost $20{\%}$ with increasing beam angle. Sensor 5DOF, 5DOFthin and 6DOFshowed no significant angle dependance.The 6DOF and 5DOFthin sensor's cable revealed no extra signal attenuation. The latter gives a smaller overall attenuation. Therefore, the 5DOFthin is chosen to be part of the novel dosimeter construction. It has a jitter error of $\pm$ 0.06 mm and a reproductibility of$ {\pm}$ 0.008 mm. In the optimal operating range, the average positional uncertainty is less than 0.2 mm. Average angle errors are at most of 1.1$°$. It is feasible to integrate an EM tracking sensor to an energy independent plastic scintillation dosimeter with minimal impact to the collected signal as well as sufficient positional accuracy to keep dose uncertainty below 5${\%}$. △ Less

Submitted 22 December, 2018; originally announced December 2018.

Investigation of the quinine sulfate dihydrate spectral properties and its effects on Cherenkov dosimetry

Authors: Emilie Jean, Marie-Eve Delage, Luc Beaulieu

Abstract: Recent studies have proposed that adding quinine to water while performing Cherenkov volumetric dosimetry improves the skewed percent depth dose measurement. The aim of this study was to quantify the ability of quinine to convert directional Cherenkov emission to isotropic fluorescence and evaluate its contribution to the total emitted light. Aqueous solutions of quinine were prepared with distill… ▽ More Recent studies have proposed that adding quinine to water while performing Cherenkov volumetric dosimetry improves the skewed percent depth dose measurement. The aim of this study was to quantify the ability of quinine to convert directional Cherenkov emission to isotropic fluorescence and evaluate its contribution to the total emitted light. Aqueous solutions of quinine were prepared with distilled water at various concentrations (0.01 to 1.2 g/L). The solutions were irradiated with photon beams at 6 and 23 MV. The dependence of the light produced as a function of sample concentration was studied using a spectrometer with a fixed integration time. Spectral measurements of the luminescent solution and the blank solution (distilled water only) were taken to deconvolve the Cherenkov and quinine contribution to the overall emission spectrum. Using a CCD camera, intensity profiles were obtained for the blank and the 1.00 g/L solutions to compare them with the dose predicted by a treatment planning system. The luminescent intensity of the samples was found to follow a logarithmic trend as a function of the quinine concentration. Based on the spectral deconvolution of the 1.00 g/L solution, 52.4% and 52.7% of the signal in the visible range results from the quinine emission at 6 and 23 MV, respectively. The remaining fraction of the spectrum is due to the Cherenkov light that has not been converted. The fraction of the Cherenkov emission produced between 250 nm and 380 nm in the water and that was absorbed by the fluorophore reached 24.8% and 9.4% respectively at 6 and 23 MV. X-ray stimulated fluorescence of the quinine was then proven to be the principal cause to the increased total light output compared to the water-only signal. This new information reinforces the direct correlation of the solution intensity to the dose deposition. △ Less

Submitted 20 May, 2019; v1 submitted 6 September, 2018; originally announced September 2018.

Optimization of a multipoint plastic scintillator dosimeter for high dose rate brachytherapy

Authors: Haydee M. Linares Rosales, Patricia Duguay-Drouin, Louis Archambault, Sam Beddar, Luc Beaulieu

Abstract: Purpose: This study aims to optimize and characterize the response of a mPSD for in vivo dosimetry in HDR brachytherapy. Methods: An exhaustive analysis was carried out in order to obtain an optimized mPSD design that maximize the scintillation light collection produced by the interaction of ionizing photons. Several mPSD prototypes were built and tested in order to determine the appropriate order… ▽ More Purpose: This study aims to optimize and characterize the response of a mPSD for in vivo dosimetry in HDR brachytherapy. Methods: An exhaustive analysis was carried out in order to obtain an optimized mPSD design that maximize the scintillation light collection produced by the interaction of ionizing photons. Several mPSD prototypes were built and tested in order to determine the appropriate order of scintillators relative to the photodetector, as well as their length as a function of the scintillation light emitted. Scintillators BCF-60, BCF-12 and BCF-10 constituted the mPSD sensitive volume.Each scintillator contribution to the total spectrum was determined by irradiations in the low energy range.For the best mPSD design, a numerical optimization was done in order to select the optical components that better match the light emission profile. The optimized dosimetric system was used for HDR brachytherapy dose determination. The system performance was quantified in term of signal to noise ratio and signal to background ratio. Results: It was determined that BCF-60 should be placed at the distal position, BCF-12 in the center and BCF-10 at proximal position with respect to the photodetector.This configuration allowed for optimized light transmission through the collecting fiber, avoiding inter-scintillator excitation and self-absorption effects.The optimized luminescence system allowed for signal deconvolution using a multispectral approach, extracting the dose to each element while taking into account Cerenkov stem effect.Differences between the mPSD measurements and TG-43 remain below 5%. In all measurement conditions, the system was able to properly differentiate the produced scintillation signal from the background one. Conclusions: A mPSD was constructed and optimized for HDR brachytherapy dosimetry, enabling real time dose determination, up to 6.5cm from the 192Ir source. △ Less

Submitted 31 May, 2019; v1 submitted 24 July, 2018; originally announced July 2018.

Combating catastrophic forgetting with developmental compression

Authors: Shawn L. E. Beaulieu, Sam Kriegman, Josh C. Bongard

Abstract: Generally intelligent agents exhibit successful behavior across problems in several settings. Endemic in approaches to realize such intelligence in machines is catastrophic forgetting: sequential learning corrupts knowledge obtained earlier in the sequence, or tasks antagonistically compete for system resources. Methods for obviating catastrophic forgetting have sought to identify and preserve fea… ▽ More Generally intelligent agents exhibit successful behavior across problems in several settings. Endemic in approaches to realize such intelligence in machines is catastrophic forgetting: sequential learning corrupts knowledge obtained earlier in the sequence, or tasks antagonistically compete for system resources. Methods for obviating catastrophic forgetting have sought to identify and preserve features of the system necessary to solve one problem when learning to solve another, or to enforce modularity such that minimally overlap** sub-functions contain task specific knowledge. While successful, both approaches scale poorly because they require larger architectures as the number of training instances grows, causing different parts of the system to specialize for separate subsets of the data. Here we present a method for addressing catastrophic forgetting called developmental compression. It exploits the mild impacts of developmental mutations to lessen adverse changes to previously-evolved capabilities and `compresses' specialized neural networks into a generalized one. In the absence of domain knowledge, developmental compression produces systems that avoid overt specialization, alleviating the need to engineer a bespoke system for every task permutation and suggesting better scalability than existing approaches. We validate this method on a robot control problem and hope to extend this approach to other machine learning domains in the future. △ Less

Submitted 11 April, 2018; originally announced April 2018.

On EM Reconstruction of a Multi Channel Shielded Applicator for Cervical Cancer Brachytherapy: A Feasibility Study

Authors: D. Tho, E. Racine, H. Easton, W. Y. Song, L. Beaulieu

Abstract: Electromagnetic tracking (EMT) is a promising technology for automated catheter and applicator reconstruc- 10 tions in brachytherapy. In this work, a proof-of-concept is presented for reconstruction of the individual channels of a shielded tandem applicator dedicated to intensity modulated brachytherapy. All six channels of a straight prototype was reconstructed and the distance between two opposi… ▽ More Electromagnetic tracking (EMT) is a promising technology for automated catheter and applicator reconstruc- 10 tions in brachytherapy. In this work, a proof-of-concept is presented for reconstruction of the individual channels of a shielded tandem applicator dedicated to intensity modulated brachytherapy. All six channels of a straight prototype was reconstructed and the distance between two opposite channels was measured. A study was also conducted on the influence of the shield on the data fluctuation of the EMT system. The differences with the CAD specified dimensions are under 2 mm. The pair of channels which has one of it more distant from the generator have 15 higher inter-channel distance with higher variability. In the first 110 cm reconstruction, all inter-channel distances are within the geometrical tolerances. According to a paired Student t-test, the data given by the EM system with and without the shield applicator tip are not significantly different. This study shows that the reconstruction of channel path within the mechanical accuracy of the applicator is possible. △ Less

Submitted 3 October, 2017; originally announced October 2017.

Comments: 3 pages, 3 figures

Journal ref: Med. Phys., (2018) 45: 1673-1676

A theoretical framework to predict the most likely ion path in particle imaging

Authors: Charles-Antoine Collins-Fekete, Lennart Volz, Stephen K. N. Portillo, Luc Beaulieu, Joao Seco

Abstract: In this work, a generic rigorous Bayesian formalism is introduced to predict the most likely path of any ion crossing a medium between two detection points. The path is predicted based on a combination of the particle scattering in the material and measurements of its initial and final position, direction and energy. The path estimate's precision is compared to the Monte Carlo simulated path. Ever… ▽ More In this work, a generic rigorous Bayesian formalism is introduced to predict the most likely path of any ion crossing a medium between two detection points. The path is predicted based on a combination of the particle scattering in the material and measurements of its initial and final position, direction and energy. The path estimate's precision is compared to the Monte Carlo simulated path. Every ion from hydrogen to carbon is simulated in two scenarios to estimate the accuracy achievable: one where the range is fixed and one where the initial velocity is fixed. In the scenario where the range is kept constant, the maximal root-mean-square error between the estimated path and the Monte Carlo path drops significantly between the proton path estimate (0.50 mm) and the helium path estimate (0.18 mm), but less so up to the carbon path estimate (0.09 mm). In the scenario where the initial velocity is kept constant, helium have systematically the minimal root-mean-square error throughout the path. As a result, helium is found to be the optimal particle for ion imaging. △ Less

Submitted 18 October, 2016; originally announced October 2016.

Comments: 20 pages, 6 figures, 1 table

Centrality dependence of the thermal excitation-energy deposition in 8-15 GeV/c hadron-Au reactions

Authors: R. A. Soltz, R. J. Newby, J. L. Klay, M. Heffner, L. Beaulieu, T. Lefort, K. Kwiatkowski, V. E. Viola

Abstract: The excitation energy per residue nucleon (E*/A) and fast and thermal light particle multiplicities are studied as a function of centrality defined as the number of grey tracks emitted N_grey and by the mean number of primary hadron-nucleon scatterings <nu> and mean impact parameter <b> extracted from it. The value of E*/A and the multiplicities show an increase with centrality for all systems,… ▽ More The excitation energy per residue nucleon (E*/A) and fast and thermal light particle multiplicities are studied as a function of centrality defined as the number of grey tracks emitted N_grey and by the mean number of primary hadron-nucleon scatterings <nu> and mean impact parameter <b> extracted from it. The value of E*/A and the multiplicities show an increase with centrality for all systems, 14.6 GeV p-Au and 8.0 GeV pi-Au and pbar-Au collisions, and the excitation energy per residue nucleon exhibits a uniform dependence on N_grey. △ Less

Submitted 9 January, 2009; v1 submitted 8 May, 2008; originally announced May 2008.

Comments: 7 pages, 6 figures

Journal ref: Phys.Rev.C79:034607,2009

Cooling Dynamics in Multi-fragmentation processes

Authors: T. X. Liu, W. G. Lynch, M. J. van Goethem, X. D. Liu, R. Shomin, W. P. Tan, M. B. Tsang, G. Verde, A. Wagner, H. F. Xi, H. S. Xu, W. A. Friedman, S. R. Souza, R. Donangelo, L. Beaulieu, B. Davin, Y. Larochelle, T. Lefort, R. T. de Souza, R. Yanez, V. E. Viola, R. J. Charity, L. G. Sobotka

Abstract: Fragment energy spectra of neutron deficient isotopes are significantly more energetic than those of neutron rich isotopes of the same element. This trend is well beyond what can be expected for the bulk multi-fragmentation of an equilibrated system. It can be explained, however, if some of these fragments are emitted earlier through the surface of the system while it is expanding and cooling. Fragment energy spectra of neutron deficient isotopes are significantly more energetic than those of neutron rich isotopes of the same element. This trend is well beyond what can be expected for the bulk multi-fragmentation of an equilibrated system. It can be explained, however, if some of these fragments are emitted earlier through the surface of the system while it is expanding and cooling. △ Less

Submitted 20 February, 2006; originally announced February 2006.

Comments: 13 pages, 3 figures

Journal ref: Europhys.Lett. 74 (2006) 806-812

Comparison of mid-velocity fragment formation with projectile-like decay

Authors: S. Hudan, R. Alfaro, B. Davin, Y. Larochelle, H. Xu, L. Beaulieu, T. Lefort, R. Yanez, R. T. de Souza, R. J. Charity, L. G. Sobotka, T. X. Liu, X. D. Liu, W. G. Lynch, R. Shomin, W. P. Tan, M. B. Tsang, A. Vander Molen, A. Wagner, H. F. Xi

Abstract: The characteristics of intermediate mass fragments (IMFs: 3<=Z<=20) produced in mid-peripheral and central collisions are compared. We compare IMFs detected at mid-velocity with those evaporated from the excited projectile-like fragment (PLF*). On average, the IMFs produced at mid-velocity are larger in atomic number, exhibit broader transverse velocity distributions, and are more neutron-rich a… ▽ More The characteristics of intermediate mass fragments (IMFs: 3<=Z<=20) produced in mid-peripheral and central collisions are compared. We compare IMFs detected at mid-velocity with those evaporated from the excited projectile-like fragment (PLF*). On average, the IMFs produced at mid-velocity are larger in atomic number, exhibit broader transverse velocity distributions, and are more neutron-rich as compared to IMFs evaporated from the PLF*. In contrast, comparison of mid-velocity fragments associated with mid-peripheral and central collisions reveals that their characteristics are remarkably similar despite the difference in impact parameter. The characteristics of mid-velocity fragments are consistent with low-density formation of the fragments. Neutron deficient isotopes of even Z elements manifest higher kinetic energies than heavier isotopes of the same element for both PLF* and mid-velocity emission. This result may be due to the decay of long-lived excited states in the field of the emitting system. △ Less

Submitted 24 January, 2005; originally announced January 2005.

Comments: 13 pages, 15 figures

Journal ref: Phys.Rev. C71 (2005) 054604

Interplay of initial deformation and Coulomb proximity on nuclear decay

Authors: S. Hudan, R. Alfaro, L. Beaulieu, B. Davin, Y. Larochelle, T. Lefort, V. E. Viola, H. Xu, R. Yanez, R. T. de Souza, R. J. Charity, L. G. Sobotka, T. X. Liu, X. D. Liu, W. G. Lynch, R. Shomin, W. P. Tan, M. B. Tsang, A. Vander, Molen A. Wagner, H. F. Xi

Abstract: Alpha particles emitted from an excited projectile-like fragment (PLF*) formed in a peripheral collision of two intermediate-energy heavy ions exhibit a strong preference for emission towards the target-like fragment (TLF). The interplay of the initial deformation of the PLF* caused by the reaction, Coulomb proximity, and the rotation of the PLF* results in the observed anisotropic angular distr… ▽ More Alpha particles emitted from an excited projectile-like fragment (PLF*) formed in a peripheral collision of two intermediate-energy heavy ions exhibit a strong preference for emission towards the target-like fragment (TLF). The interplay of the initial deformation of the PLF* caused by the reaction, Coulomb proximity, and the rotation of the PLF* results in the observed anisotropic angular distribution. Changes in the shape of the angular distribution with excitation energy are interpreted as being the result of forming more elongated initial geometries in the more peripheral collisions. △ Less

Submitted 14 May, 2004; originally announced May 2004.

Comments: 4 figures

Journal ref: Phys.Rev. C70 (2004) 031601

Effects of in-medium cross-sections and optical potential on thermal-source formation in p+197Au reactions at 6.2-14.6 GeV/c

Authors: S. Turbide, L. Beaulieu, P. Danielewicz, V. E. Viola, R. Roy, K. Kwiatkowski, W. -C. Hsi, G. Wang, T. Lefort, D. S. Bracken, H. Breuer, E. Cornell, F. Gimeno-Nogues, D. S. Ginger, S. Gushue, R. Huang, R. Korteling, W. G. Lynch, K. B. Morley, E. Ramakrishnan, L. P. Remsberg, D. Rowland, M. B. Tsang, H. Xi, S. J. Yennello

Abstract: Effects of in-medium cross-sections and of optical potential on pre-equilibrium emission and on formation of a thermal source are investigated by comparing the results of transport simulations with experimental results from the p+{197}Au reaction at 6.2-14.6 GeV/c. The employed transport model includes light composite-particle production and allows for inclusion of in-medium particle-particle cr… ▽ More Effects of in-medium cross-sections and of optical potential on pre-equilibrium emission and on formation of a thermal source are investigated by comparing the results of transport simulations with experimental results from the p+{197}Au reaction at 6.2-14.6 GeV/c. The employed transport model includes light composite-particle production and allows for inclusion of in-medium particle-particle cross-section reduction and of momentum dependence in the particle optical-potentials. Compared to the past, the model incorporates improved parameterizations of elementary high-energy processes. The simulations indicate that the majority of energy deposition occurs during the first ~25 fm/c of a reaction. This is followed by a pre-equilibrium emission and readjustment of system density and momentum distribution toward an equilibrated system. Good agreement with data, on the d/p and t/p yield ratios and on the residue mass and charge numbers, is obtained at the time of ~ 65 fm/c from the start of a reaction, provided reduced in-medium cross-sections and momentum-dependent optical potentials are employed in the simulations. By then, the pre-equilibrium nucleon and cluster emission, as well as mean-field readjustments, drive the system to a state of depleted average density, rho/rho_{0} ~ 1/4-1/3 for central collisions, and low-to-moderate excitation, i.e. the region of nuclear liquid-gas phase transition. △ Less

Submitted 20 February, 2004; originally announced February 2004.

Comments: 35 pages, 14 figures

Journal ref: Phys.Rev. C70 (2004) 014608

Isospin Diffusion in Heavy Ion Reactions

Authors: M. B. Tsang, T. X. Liu, L. Shi, P. Danielewicz, C. K. Gelbke, X. D. Liu, W. G. Lynch, W. P. Tan, G. Verde, A. Wagner, H. S. Xu, W. A. Friedman, L. Beaulieu, B. Davin, R. T. de Souza, Y. Larochelle, T. Lefort, R. Yanez, V. E. Viola Jr, R. J. Charity, L. G. Sobotka

Abstract: Using symmetric 112Sn+112Sn, 124Sn+124Sn collisions as references, we probe isospin diffusion in peripheral asymmetric 112Sn+124Sn, 124Sn+112Sn systems at incident energy of E/A=50 MeV. Isoscaling analyses imply that the quasi-projectile and quasi-target in these collisions do not achieve isospin equilibrium, permitting an assessment of the isospin transport rates. We find that comparisons betwe… ▽ More Using symmetric 112Sn+112Sn, 124Sn+124Sn collisions as references, we probe isospin diffusion in peripheral asymmetric 112Sn+124Sn, 124Sn+112Sn systems at incident energy of E/A=50 MeV. Isoscaling analyses imply that the quasi-projectile and quasi-target in these collisions do not achieve isospin equilibrium, permitting an assessment of the isospin transport rates. We find that comparisons between isospin sensitive experimental and theoretical observables, using suitably chosen scaled ratios, permit investigation of the density dependence of the asymmetry term of the nuclear equation of state. △ Less

Submitted 25 October, 2003; originally announced October 2003.

Comments: 11 pages, 3 figures

Coulomb proximity decay: A clock for measuring the particle emission time scale

Authors: S. Hudan, A. S. Botvina, R. Alfaro, L. Beaulieu, B. Davin, Y. Larochelle, T. Lefort, V. E. Viola, H. Xu, R. Yanez, R. T. de Souza, T. X. Liu, X. D. Liu, W. G. Lynch, R. Shomin, W. P. Tan, M. B. Tsang, A. Vander Molen, A. Wagner, H. F. Xi, R. J. Charity, L. G. Sobotka

Abstract: A new method to examine the time scale of particle emission from hot nuclei is explored. Excited projectile-like and target-like fragments decay as they separate following a peripheral heavy-ion collision. Their mutual Coulomb influence results in an anisotropic angular distribution of emitted particles, providing a measure of the particle emission time scale. Predictions of a schematic evaporat… ▽ More A new method to examine the time scale of particle emission from hot nuclei is explored. Excited projectile-like and target-like fragments decay as they separate following a peripheral heavy-ion collision. Their mutual Coulomb influence results in an anisotropic angular distribution of emitted particles, providing a measure of the particle emission time scale. Predictions of a schematic evaporation model are presented and compared to experimental data. △ Less

Submitted 4 September, 2003; v1 submitted 28 August, 2003; originally announced August 2003.

Comments: 10 pages, 5 figures

Excitation and decay of projectile-like fragments formed in dissipative peripheral collisions at intermediate energies

Authors: R. Yanez, S. Hudan, R. Alfaro, B. Davin, Y. Larochelle, H. Xu, L. Beaulieu, T. Lefort, V. E. Viola, R. T. de Souza, T. X. Liu, X. D. Liu, W. G. Lynch, R. Shomin, W. P. Tan, M. B. Tsang, A. Vander Molen, A. Wagner, H. F. Xi, R. J. Charity, L. G. Sobotka

Abstract: Projectile-like fragments (PLF:15<=Z<=46) formed in peripheral and mid-peripheral collisions of 114Cd projectiles with 92Mo nuclei at E/A=50 MeV have been detected at very forward angles, 2.1 deg.<=theta_lab<=4.2 deg. Calorimetric analysis of the charged particles observed in coincidence with the PLF reveals that the excitation of the primary PLF is strongly related to its velocity dam**. Furt… ▽ More Projectile-like fragments (PLF:15<=Z<=46) formed in peripheral and mid-peripheral collisions of 114Cd projectiles with 92Mo nuclei at E/A=50 MeV have been detected at very forward angles, 2.1 deg.<=theta_lab<=4.2 deg. Calorimetric analysis of the charged particles observed in coincidence with the PLF reveals that the excitation of the primary PLF is strongly related to its velocity dam**. Furthermore, for a given V_PLF*, its excitation is not related to its size, Z_PLF*. For the largest velocity dam**, the excitation energy attained is large, approximately commensurate with a system at the limiting temperature △ Less

Submitted 2 June, 2003; originally announced June 2003.

Comments: 5 pages, 6 figures

Journal ref: Phys.Rev. C68 (2003) 011602

Precise Barriers and Shell Effects: a New Inroad to Fission Saddle Point Spectroscopy

Authors: L. Phair, L. G. Moretto, K. X. **g, L. Beaulieu, D. Breus, J. B. Elliott, T. S. Fan, Th. Rubehn, G. J. Wozniak

Abstract: Fission excitation functions have been measured for a chain of neighboring compound nuclei, from 207Po to 212Po. We present a new analysis which provides a determination of the fission barriers and ground state shell effects with nearly spectroscopic accuracy. The improved accuracy achieved in this analysis may lead to a future detailed exploration of the saddle mass surface and its spectroscopy… ▽ More Fission excitation functions have been measured for a chain of neighboring compound nuclei, from 207Po to 212Po. We present a new analysis which provides a determination of the fission barriers and ground state shell effects with nearly spectroscopic accuracy. The improved accuracy achieved in this analysis may lead to a future detailed exploration of the saddle mass surface and its spectroscopy. The sensitivity of the fission probabilities on shell effects extends to excitation energies of 150 MeV and negates recent claims for the disappearance of shell corrections due to collective effects. △ Less

Submitted 6 March, 2003; originally announced March 2003.

Comments: 10 pages, 3 figures

Report number: LBNL-51709

Fragment Production in Non-central Collisions of Intermediate Energy Heavy Ions

Authors: B. Davin, R. Alfaro, H. Xu, L. Beaulieu, Y. Larochelle, T. Lefort, R. Yanez, S. Hudan, A. L. Caraley, R. T. de Souza, T. X. Liu, X. D. Liu, W. G. Lynch, R. Shomin, W. P. Tan, M. B. Tsang, A. Vander Molen, A. Wagner, H. F. Xi, C. K. Gelbke, R. J. Charity, L. G. Sobotka

Abstract: The defining characteristics of fragment emission resulting from the non-central collision of 114Cd ions with 92Mo target nuclei at E/A = 50 MeV are presented. Charge correlations and average relative velocities for mid-velocity fragment emission exhibit significant differences when compared to standard statistical decay. These differences associated with similar velocity dissipation are indicat… ▽ More The defining characteristics of fragment emission resulting from the non-central collision of 114Cd ions with 92Mo target nuclei at E/A = 50 MeV are presented. Charge correlations and average relative velocities for mid-velocity fragment emission exhibit significant differences when compared to standard statistical decay. These differences associated with similar velocity dissipation are indicative of the influence of the entrance channel dynamics on the fragment production process. △ Less

Submitted 23 November, 2002; originally announced November 2002.

Journal ref: Phys.Rev. C65 (2002) 064614

Similarity of fragment characteristics at mid-velocity for mid-peripheral and central collisions

Authors: S. Hudan, R. Alfaro, B. Davin, Y. Larochelle, H. Xu, L. Beaulieu, T. Lefort, V. E. Viola, R. Yanez, R. T. de Souza, T. X. Liu, X. D. Liu, W. G. Lynch, R. Shomin, W. P. Tan, M. B. Tsang, A. Vander Molen, A. Wagner, H. F. Xi, C. K. Gelbke, R. J. Charity, L. G. Sobotka

Abstract: The characteristics, in particular the isotopic composition (N/Z), of intermediate mass fragments (IMF : 3<=Z<=20) produced near the center-of-mass in mid-peripheral and central collisions of 114Cd ions with 92Mo target nuclei at E/A=50 MeV are compared to that of IMFs emitted from the projectile-like fragment (PLF) in mid-peripheral collisions. IMFs produced at mid-velocities are on average lar… ▽ More The characteristics, in particular the isotopic composition (N/Z), of intermediate mass fragments (IMF : 3<=Z<=20) produced near the center-of-mass in mid-peripheral and central collisions of 114Cd ions with 92Mo target nuclei at E/A=50 MeV are compared to that of IMFs emitted from the projectile-like fragment (PLF) in mid-peripheral collisions. IMFs produced at mid-velocities are on average larger in atomic number, more energetic, and more neutron-rich as compared to IMFs emitted from the PLF. In contrast, the characteristics of mid-velocity IMFs in central collisions and mid-peripheral collisions are comparable. △ Less

Submitted 21 December, 2004; v1 submitted 5 October, 2002; originally announced October 2002.

Comments: This paper has been withdrawn to include efficiency calculations

Isotope yields from central 112,124Sn+112,124Sn collisions, dynamical emission?

Authors: T. X. Liu, X. D. Liu, M. J. van Goethem, W. G. Lynch, R. Shomin, W. P. Tan, M. B. Tsang, G. Verde, A. Wagner, H. F. Xi, H. S. Xu, M. Colonna, M. Di Toro, M. Zielinska-Pfabe, H. H. Wolter, L. Beaulieu, B. Davin, Y. Larochelle, T. Lefort, R. T. de Souza, R. Yanez, V. E. Viola, R. J. Charity, L. G. Sobotka

Abstract: Isotopic yields for light particles and intermediate mass fragments have been measured for 112Sn+112Sn, 112Sn+124Sn, 124Sn+112Sn and 124Sn+124Sn central collisions at E/A=50 MeV and compared with predictions of stochastic mean field calculations. These calculations predict a sensitivity of the isotopic distributions to the density dependence of the asymmetry term of the nuclear equation of state… ▽ More Isotopic yields for light particles and intermediate mass fragments have been measured for 112Sn+112Sn, 112Sn+124Sn, 124Sn+112Sn and 124Sn+124Sn central collisions at E/A=50 MeV and compared with predictions of stochastic mean field calculations. These calculations predict a sensitivity of the isotopic distributions to the density dependence of the asymmetry term of the nuclear equation of state. However, the secondary decay of the excited fragments modifies significantly the primary isotopic distributions and these modifications are rather sensitive to theoretical uncertainties in the excitation energies of the hot fragments. The predicted final isotope distributions are narrower than the experimental data and the sensitivity of the predicted yields to the density dependence of the asymmetry term is reduced. △ Less

Submitted 2 October, 2002; originally announced October 2002.

Comments: 30 pages, 7 figures

Journal ref: Phys.Rev.C69:014603,2004

Tracking the phase-transition energy in disassembly of hot nuclei

Authors: C. B. Das, S. Das Gupta, L. Beaulieu, T. Lefort, K. Kwiatkowski, V. E. Viola, S. J. Yennello, L. Pienkowski, R. G. Korteling, H. Breuer

Abstract: In efforts to determine phase transitions in the disintegration of highly excited heavy nuclei, a popular practice is to parametrise the yields of isotopes as a function of temperature in the form $Y(z)=z^{-τ}f(z^σ(T-T_0))$, where $Y(z)$'s are the measured yields and $τ, σ$ and $T_0$ are fitted to the yields. Here $T_0$ would be interpreted as the phase transition temperature. For finite systems… ▽ More In efforts to determine phase transitions in the disintegration of highly excited heavy nuclei, a popular practice is to parametrise the yields of isotopes as a function of temperature in the form $Y(z)=z^{-τ}f(z^σ(T-T_0))$, where $Y(z)$'s are the measured yields and $τ, σ$ and $T_0$ are fitted to the yields. Here $T_0$ would be interpreted as the phase transition temperature. For finite systems such as those obtained in nuclear collisions, this parametrisation is only approximate and hence allows for extraction of $T_0$ in more than one way. In this work we look in detail at how values of $T_0$ differ, depending on methods of extraction. It should be mentioned that for finite systems, this approximate parametrisation works not only at the critical point, but also for first order phase transitions (at least in some models). Thus the approximate fit is no guarantee that one is seeing a critical phenomenon. A different but more conventional search for the nuclear phase transition would look for a maximum in the specific heat as a function of temperature $T_2$. In this case $T_2$ is interpreted as the phase transition temperature. Ideally $T_0$ and $T_2$ would coincide. We invesigate this possibility, both in theory and from the ISiS data, performing both canonical ($T$) and microcanonical ($e=E^*/A$) calculations. Although more than one value of $T_0$ can be extracted from the approximate parmetrisation, the work here points to the best value from among the choices. Several interesting results, seen in theoretical calculations, are borne out in experiment. △ Less

Submitted 24 June, 2002; originally announced June 2002.

Comments: Revtex, 10 pages including 8 figures and 2 tables

Journal ref: Phys.Rev. C66 (2002) 044602

Caloric curve of 8 GeV/c negative pion and antiproton + Au reactions

Authors: A. Ruangma, R. Laforest, E. Martin, E. Ramakrishnan, D. J. Rowland, M. Veselsky, E. M. Winchester, S. J. Yennello, L. Beaulieu, W. -c. Hsi, K. Kwiatkowski, T. Lefort, V. E. Viola, A. Botvina, R. G. Korteling, L. Pienkowski, H. Breuer, S. Gushue, L. P. Remsberg

Abstract: The relationship between nuclear temperature and excitation energy of hot nuclei formed by 8 GeV/c negative pion and antiproton beams incident on 197Au has been investigated with the ISiS 4-pidetector array at the BNL AGS accelerator. The double-isotope-ratio technique was used to calculate the temperature of the hot system. The two thermometers used (p/d-3He/4He) and (d/t-3He/4He) are in agreem… ▽ More The relationship between nuclear temperature and excitation energy of hot nuclei formed by 8 GeV/c negative pion and antiproton beams incident on 197Au has been investigated with the ISiS 4-pidetector array at the BNL AGS accelerator. The double-isotope-ratio technique was used to calculate the temperature of the hot system. The two thermometers used (p/d-3He/4He) and (d/t-3He/4He) are in agreement below E*/A ~ 7 MeV when corrected for secondary decay. Comparison of these caloric curves to those from other experiments shows some differences that may be attributable to instrumentation and analysis procedures. The caloric curves from this experiment are also compared with the predictions from the SMM multifragmentation model. △ Less

Submitted 4 October, 2001; originally announced October 2001.

Comments: 34 pages, 11 figures

Journal ref: Phys.Rev.C66:044603,2002

Event-by-Event Analysis of Proton-Induced Nuclear Multifragmentation: Determination of Phase Transition Universality-Class in System with Extreme Finite-Size Constraints

Authors: M. Kleine Berkenbusch, W. Bauer, K. Dillman, S. Pratt, L. Beaulieu, K. Kwiatkowski, T. Lefort, W. -c. Hsi, V. Viola, S. J. Yennello, R. G. Korteling, H. Breuer

Abstract: A percolation model of nuclear fragmentation is used to interpret 10.2 GeV/c p+197Au multi-fragmentation data. Emphasis is put on finding signatures of a continuous nuclear matter phase transition in finite nuclear systems. Based on model calculations, corrections accounting for physical constraints of the fragment detection and sequential decay processes are derived. Strong circumstantial evide… ▽ More A percolation model of nuclear fragmentation is used to interpret 10.2 GeV/c p+197Au multi-fragmentation data. Emphasis is put on finding signatures of a continuous nuclear matter phase transition in finite nuclear systems. Based on model calculations, corrections accounting for physical constraints of the fragment detection and sequential decay processes are derived. Strong circumstantial evidence for a continuous phase transition is found, and the values of two critical exponents, sigma = 0.5+-0.1 and tau = 2.35+-0.05, are extracted from the data. A critical temperature of T_c = 8.3+-0.2 MeV is found. △ Less

Submitted 20 September, 2001; originally announced September 2001.

Comments: 5 pages, 4 figures, submitted to Phys. Rev. Lett

Journal ref: Phys.Rev.Lett. 88 (2002) 022701

A Quasi-Classical Model of Intermediate Velocity Particle Production in Asymmetric Heavy Ion Reactions

Authors: A. Chernomoretz, L. Gingras, Y. Larochelle, L. Beaulieu, R. Roy, C. St-Pierre, C. O. Dorso

Abstract: The particle emission at intermediate velocities in mass asymmetric reactions is studied within the framework of classical molecular dynamics. Two reactions in the Fermi energy domain were modelized, $^{58}$Ni+C and $^{58}$Ni+Au at 34.5 MeV/nucleon. The availability of microscopic correlations at all times allowed a detailed study of the fragment formation process. Special attention was paid to… ▽ More The particle emission at intermediate velocities in mass asymmetric reactions is studied within the framework of classical molecular dynamics. Two reactions in the Fermi energy domain were modelized, $^{58}$Ni+C and $^{58}$Ni+Au at 34.5 MeV/nucleon. The availability of microscopic correlations at all times allowed a detailed study of the fragment formation process. Special attention was paid to the physical origin of fragments and emission timescales, which allowed us to disentangle the different processes involved in the mid-rapidity particle production. Consequently, a clear distinction between a prompt pre- equilibrium emission and a delayed aligned asymmetric breakup of the heavier partner of the reaction was achieved. △ Less

Submitted 20 March, 2002; v1 submitted 31 August, 2001; originally announced August 2001.

Comments: 8 pages, 7 figures. Final version: figures were redesigned, and a new section discussing the role of Coulomb in IMF production was included

Journal ref: Phys.Rev. C65 (2002) 054613

Origins of Intermediate Velocity Particle Production in Heavy Ion Reactions

Authors: L. Gingras, A. Chernomoretz, Y. Larochelle, Z. Y. He, L. Beaulieu, G. C. Ball, F. Grenier, D. Horn, R. Roy, M. Samri, C. St-Pierre, D. Theriault, S. Turbide

Abstract: Investigation of intermediate-velocity particle production is performed on entrance channel mass asymmetric collisions of 58Ni+C and 58Ni+Au at 34.5 MeV/nucleon. Distinctions between prompt pre-equilibrium ejections, multiple neck ruptures and an alternative phenomenon of delayed aligned asymmetric breakup is achieved using source reconstructed correlation observables and time-based cluster reco… ▽ More Investigation of intermediate-velocity particle production is performed on entrance channel mass asymmetric collisions of 58Ni+C and 58Ni+Au at 34.5 MeV/nucleon. Distinctions between prompt pre-equilibrium ejections, multiple neck ruptures and an alternative phenomenon of delayed aligned asymmetric breakup is achieved using source reconstructed correlation observables and time-based cluster recognition in molecular dynamics simulations. △ Less

Submitted 31 August, 2001; originally announced August 2001.

Comments: 5 pages, 4 figures

Journal ref: Phys.Rev. C65 (2002) 061604

Fragment Isospin as a Probe of Heavy-Ion Collisions

Authors: H. Xu, R. Alfaro, B. Davin, L. Beaulieu, Y. Larochelle, T. Lefort, R. Yanez, R. T. de Souza, T. X. Liu, X. D. Liu, W. G. Lynch, R. Shomin, W. P. Tan, M. B. Tsang, A. Vander Molen, A. Wagner, H. F. Xi, C. K. Gelbke, R. J. Charity, L. G. Sobotka, A. S. Botvina

Abstract: Isotope ratios of fragments produced at mid-rapidity in peripheral and central collisions of 114Cd ions with 92Mo and 98Mo target nuclei at E/A = 50 MeV are compared. Neutron-rich isotopes are preferentially produced in central collisions as compared to peripheral collisions. The influence of the size (A), density, N/Z, E*/A, and Eflow/A of the emitting source on the measured isotope ratios was… ▽ More Isotope ratios of fragments produced at mid-rapidity in peripheral and central collisions of 114Cd ions with 92Mo and 98Mo target nuclei at E/A = 50 MeV are compared. Neutron-rich isotopes are preferentially produced in central collisions as compared to peripheral collisions. The influence of the size (A), density, N/Z, E*/A, and Eflow/A of the emitting source on the measured isotope ratios was explored by comparison with a statistical model (SMM). The mid-rapidity region associated with peripheral collisions does not appear to be neutron-enriched relative to central collisions. △ Less

Submitted 16 July, 2001; originally announced July 2001.

Comments: 12 pages including figures

Journal ref: Phys.Rev. C65 (2002) 061602

The liquid to vapor phase transition in excited nuclei

Authors: J. B. Elliott, L. G. Moretto, L. Phair, G. J. Wozniak, T. Lefort, L. Beaulieu, K. Kwiatkowski, W. -C. Hsi, L. Pienkowski, H. Breuer, R. G. Korteling, R. Laforest, E. Martin, E. Ramakrishnan, D. Rowland, A. Ruangma, V. E. Viola, E. Winchester, S. J. Yennello

Abstract: For many years it has been speculated that excited nuclei would undergo a liquid to vapor phase transition. For even longer, it has been known that clusterization in a vapor carries direct information on the liquid- vapor equilibrium according to Fisher's droplet model. Now the thermal component of the 8 GeV/c pion + 197Au multifragmentation data of the ISiS Collaboration is shown to follow the… ▽ More For many years it has been speculated that excited nuclei would undergo a liquid to vapor phase transition. For even longer, it has been known that clusterization in a vapor carries direct information on the liquid- vapor equilibrium according to Fisher's droplet model. Now the thermal component of the 8 GeV/c pion + 197Au multifragmentation data of the ISiS Collaboration is shown to follow the scaling predicted by Fisher's model, thus providing the strongest evidence yet of the liquid to vapor phase transition. △ Less

Submitted 2 May, 2001; v1 submitted 11 April, 2001; originally announced April 2001.

Comments: four pages, four figures, first two in color (corrected typo in Ref. [26], corrected error in Fig. 4)

Report number: LBNL-47711

Journal ref: Phys.Rev.Lett.88:042701,2002

Breakup time scale studied in the 8 GeV/c pi- + 197Au reaction

Authors: L. Pienkowski, K. Kwiatkowski, T. Lefort, W. -c. Hsi, L. Beaulieu, A. Botvina, B. Back, H. Breuer, S. Gushue, R. G. Korteling, R. Laforest, E. Martin, E. Ramakrishnan, L. P. Remsberg, D. Rowland, A. Ruangma, V. E. Viola, E. Winchester, S. J. Yennello

Abstract: Experimental data from the reaction of an 8.0 GeV/c pi- beam incident on a 197Au target have been analyzed in order to investigate the integrated breakup time scale for hot residues. Alpha-particle energy spectra and particle angular distributions supported by a momentum tensor analysis suggest that at large excitation energy, above 3-5 MeV/nucleon, light-charged particles are emitted prior to o… ▽ More Experimental data from the reaction of an 8.0 GeV/c pi- beam incident on a 197Au target have been analyzed in order to investigate the integrated breakup time scale for hot residues. Alpha-particle energy spectra and particle angular distributions supported by a momentum tensor analysis suggest that at large excitation energy, above 3-5 MeV/nucleon, light-charged particles are emitted prior to or at the same time as the emission of the heavy fragments. Comparison with the SMM and GEMINI models is presented. A binary fission-like mechanism fits the experimental data at low excitation energies, but seems unable to reproduce the data at excitation energies above 3-5 MeV/nucleon. △ Less

Submitted 16 September, 2000; originally announced September 2000.

Comments: 12 pages including 3 postscript figures

Signals for a Transition from Surface to Bulk Emission in Thermal Multifragmentation

Authors: L. Beaulieu, T. Lefort, K. Kwiatkowski, R. T. de Souza, W. -c. Hsi, L. Pienkowski, B. Back, D. S. Bracken, H. Breuer, E. Cornell, F. Gimeno-Nogues, D. S. Ginger, S. Gushue, R. G. Korteling, R. Laforest, E. Martin, K. B. Morley, E. Ramakrishnan, L. P. Remsberg, D. Rowland, A. Ruangma, V. E. Viola, G. Wang, E. Winchester, S. J. Yennello

Abstract: Excitation-energy-gated two-fragment correlation functions have been studied between 2 to 9A MeV of excitation energy for equilibrium-like sources formed in $π^-$ and p + $^{197}$Au reactions at beam momenta of 8,9.2 and 10.2 GeV/c. Comparison of the data to an N-body Coulomb-trajectory code shows a decrease of one order of magnitude in the fragment emission time in the excitation energy interva… ▽ More Excitation-energy-gated two-fragment correlation functions have been studied between 2 to 9A MeV of excitation energy for equilibrium-like sources formed in $π^-$ and p + $^{197}$Au reactions at beam momenta of 8,9.2 and 10.2 GeV/c. Comparison of the data to an N-body Coulomb-trajectory code shows a decrease of one order of magnitude in the fragment emission time in the excitation energy interval 2-5A MeV, followed by a nearly constant breakup time at higher excitation energy. The observed decrease in emission time is shown to be strongly correlated with the increase of the fragment emission probability, and the onset of thermally-induced radial expansion. This result is interpreted as evidence consistent with a transition from surface-dominated to bulk emission expected for spinodal decomposition. △ Less

Submitted 11 April, 2000; originally announced April 2000.

Comments: 11 pages including 3 postscript figures (1 color)

Report number: INC-40007-140

Journal ref: Phys.Rev.Lett. 84 (2000) 5971-5974

Isospin Fractionation in Nuclear Multifragmentation

Authors: H. S. Xu, M. B. Tsang, T. X. Liu, X. D. Liu, W. G. Lynch, W. P. Tan, G. Verde, A. VanderMolen, A. Wagnera, H. F. Xib, C. K. Gelbke, L. Beaulieu, B. Davin, Y. Larochellec, T. Lefort, R. T. de Souza, R. Yanez, V. Viola, R. J. Charity, L. G. Sobotka

Abstract: Isotopic distributions for light particles and intermediate mass fragments have been measured for 112Sn+112Sn, 112Sn+124Sn, 124Sn+112Sn and 124Sn+124Sn collisions at E/A=50 MeV. Isotope, isotone and isobar yield ratios are utilized to obtain an estimate of the isotopic composition of the gas phase, i.e., the relative abundance of free neutrons and protons at breakup. Within the context of equili… ▽ More Isotopic distributions for light particles and intermediate mass fragments have been measured for 112Sn+112Sn, 112Sn+124Sn, 124Sn+112Sn and 124Sn+124Sn collisions at E/A=50 MeV. Isotope, isotone and isobar yield ratios are utilized to obtain an estimate of the isotopic composition of the gas phase, i.e., the relative abundance of free neutrons and protons at breakup. Within the context of equilibrium calculations, these analyses indicate that the gas phase is enriched in neutrons relative to the liquid phase represented by bound nuclei. △ Less

Submitted 1 November, 1999; originally announced October 1999.

Comments: 14 paged, 3 figures

Report number: msucl-1137

Journal ref: Phys.Rev.Lett. 85 (2000) 716-719

Thermally-induced expansion in the 8 GeV/c $π^-$ + $^{197}$Au reaction

Authors: T. Lefort, L. Beaulieu, A. Botvina, D. Durand, K. Kwiatkowski, W. -c. Hsi, L. Pienkowski, B. Back, H. Breuer, S. Gushue, R. G. Korteling, R. Laforest E. Martin, E. Ramakrishnan, L. P. Remsberg, D. Rowland, A. Ruangma, V. E. Viola, E. Winchester, S. J. Yennello

Abstract: Fragment kinetic energy spectra for reactions induced by 8.0 GeV/c $\rm{π^-}$ beams incident on a $\rm{^{197}}$Au target have been analyzed in order to deduce the possible existence and influence of thermal expansion. The average fragment kinetic energies are observed to increase systematically with fragment charge but are nearly independent of excitation energy. Comparison of the data with stat… ▽ More Fragment kinetic energy spectra for reactions induced by 8.0 GeV/c $\rm{π^-}$ beams incident on a $\rm{^{197}}$Au target have been analyzed in order to deduce the possible existence and influence of thermal expansion. The average fragment kinetic energies are observed to increase systematically with fragment charge but are nearly independent of excitation energy. Comparison of the data with statistical multifragmentation models indicates the onset of extra collective thermal expansion near an excitation energy of E*/A $\rm{\approx}$ 5 MeV. However, this effect is weak relative to the radial expansion observed in heavy-ion-induced reactions, consistent with the interpretation that the latter expansion may be driven primarily by dynamical effects such as compression/decompression. △ Less

Submitted 19 November, 1999; v1 submitted 29 October, 1999; originally announced October 1999.

Comments: 12 pages including 4 postscript figures

Journal ref: Phys.Rev. C62 (2000) 031604

A statistical interpretation of the correlation between intermediate mass fragment multiplicity and transverse energy

Authors: L. Phair, L. Beaulieu, L. G. Moretto, G. J. Wozniak, D. R. Bowman, N. Carlin, L. Celano, N. Colonna, J. D. Dinius, A. Ferrero, C. K. Gelbke, T. Glasmacher, F. Gramegna, D. O. Handzy, W. C. Hsi, M. J. Huang, I. Iori, Y. D. Kim, M. A. Lisa, W. G. Lynch, G. V. Margagliotti, P. F. Mastinu, P. M. Milazzo, C. P. Montoya, A. Moroni , et al. (7 additional authors not shown)

Abstract: Multifragment emission following Xe+Au collisions at 30, 40, 50 and 60 AMeV has been studied with multidetector systems covering nearly 4-pi in solid angle. The correlations of both the intermediate mass fragment and light charged particle multiplicities with the transverse energy are explored. A comparison is made with results from a similar system, Xe+Bi at 28 AMeV. The experimental trends are… ▽ More Multifragment emission following Xe+Au collisions at 30, 40, 50 and 60 AMeV has been studied with multidetector systems covering nearly 4-pi in solid angle. The correlations of both the intermediate mass fragment and light charged particle multiplicities with the transverse energy are explored. A comparison is made with results from a similar system, Xe+Bi at 28 AMeV. The experimental trends are compared to statistical model predictions. △ Less

Submitted 9 September, 1999; originally announced September 1999.

Comments: 7 pages, submitted to Phys. Rev. C

Report number: LBNL-41893

Journal ref: Phys.Rev.C60:054617,1999

Thermal excitation of heavy nuclei with 5-15 GeV/c antiproton, proton and pion beams

Authors: L. Beaulieu, K. Kwiatkowski, W. -c. Hsi, T. Lefort, L. Pienkowski, R. G. Korteling, G. Wang, B. Back, D. S. Bracken, H. Breuer, E. Cornell, F. Gimeno-Nogues, D. S. Ginger, S. Gushue, M. J. Huang, R. Laforest, W. G. Lynch, E. Martin, K. B. Morley, E. Ramakrishnan, L. P. Remsberg, D. Rowland, A. Ruangma, M. B. Tsang, V. E. Viola , et al. (3 additional authors not shown)

Abstract: Excitation-energy distributions have been derived from measurements of 5.0-14.6 GeV/c antiproton, proton and pion reactions with $^{197}$Au target nuclei, using the ISiS 4$π$ detector array. The maximum probability for producing high excitation-energy events is found for the antiproton beam relative to other hadrons, $^3$He and $\bar{p}$ beams from LEAR. For protons and pions, the excitation-ene… ▽ More Excitation-energy distributions have been derived from measurements of 5.0-14.6 GeV/c antiproton, proton and pion reactions with $^{197}$Au target nuclei, using the ISiS 4$π$ detector array. The maximum probability for producing high excitation-energy events is found for the antiproton beam relative to other hadrons, $^3$He and $\bar{p}$ beams from LEAR. For protons and pions, the excitation-energy distributions are nearly independent of hadron type and beam momentum above about 8 GeV/c. The excitation energy enhancement for $\bar{p}$ beams and the saturation effect are qualitatively consistent with intranuclear cascade code predictions. For all systems studied, maximum cluster sizes are observed for residues with E*/A $\sim$ 6 MeV. △ Less

Submitted 30 August, 1999; v1 submitted 25 June, 1999; originally announced June 1999.

Comments: 14 pages including 5 figures and 1 table. Accepted in Physics Letter B. also available at http://nuchem.iucf.indiana.edu/

Report number: Indiana University, INC-40007-138

Journal ref: Phys.Lett. B463 (1999) 159-167