-
Discrepancies in dynamic yield stress measurements of cement pastes
Authors:
Subhransu Dhar,
Teresa Liberto,
Catherine Barentin,
Thibaut Divoux,
Agathe Robisson
Abstract:
The dynamic yield stress associated with the flow cessation of cement pastes is measured using a rheometer equipped with various shear geometries such as vane, helical, sandblasted co-axial cylinders, and serrated parallel plates, as well as with the mini-cone spread test. Discrepancies in yield stress values are observed for cement pastes at various volume fractions, with one to two orders of mag…
▽ More
The dynamic yield stress associated with the flow cessation of cement pastes is measured using a rheometer equipped with various shear geometries such as vane, helical, sandblasted co-axial cylinders, and serrated parallel plates, as well as with the mini-cone spread test. Discrepancies in yield stress values are observed for cement pastes at various volume fractions, with one to two orders of magnitude difference between vane, helical and mini-cone spread measurements on the one hand, and co-axial cylinder and parallel plate measurements on the other hand. To understand this discrepancy, the flow profile of a cement paste in the parallel-plate geometry is investigated with a high-speed camera, revealing the rapid formation of an un-sheared band near the static bottom plate. The width of this band depends upon the rotational velocity of the top plate, and upon the shear time. Recalculation of shear stress shows that the reduced sheared gap alone cannot explain the low measured yield stress. Further exploration suggests the formation of zones with lower particle content, possibly linked to cement particle sedimentation. Here, we argue that the complex nature of cement pastes, composed of negatively buoyant non-Brownian particles with attractive interactions due to highly charged nano-size hydration products, accounts for their complex rheological behavior.
△ Less
Submitted 19 March, 2024;
originally announced March 2024.
-
Ductile-to-brittle transition and yielding in soft amorphous materials: perspectives and open questions
Authors:
Thibaut Divoux,
Elisabeth Agoritsas,
Stefano Aime,
Catherine Barentin,
Jean-Louis Barrat,
Roberto Benzi,
Ludovic Berthier,
Dapeng Bi,
Giulio Biroli,
Daniel Bonn,
Philippe Bourrianne,
Mehdi Bouzid,
Emanuela Del Gado,
Hélène Delanoë-Ayari,
Kasra Farain,
Suzanne Fielding,
Matthias Fuchs,
Jasper van der Gucht,
Silke Henkes,
Maziyar Jalaal,
Yogesh M. Joshi,
Anaël Lemaître,
Robert L. Leheny,
Sébastien Manneville,
Kirsten Martens
, et al. (15 additional authors not shown)
Abstract:
Soft amorphous materials are viscoelastic solids ubiquitously found around us, from clays and cementitious pastes to emulsions and physical gels encountered in food or biomedical engineering. Under an external deformation, these materials undergo a noteworthy transition from a solid to a liquid state that reshapes the material microstructure. This yielding transition was the main theme of a worksh…
▽ More
Soft amorphous materials are viscoelastic solids ubiquitously found around us, from clays and cementitious pastes to emulsions and physical gels encountered in food or biomedical engineering. Under an external deformation, these materials undergo a noteworthy transition from a solid to a liquid state that reshapes the material microstructure. This yielding transition was the main theme of a workshop held from January 9 to 13, 2023 at the Lorentz Center in Leiden. The manuscript presented here offers a critical perspective on the subject, synthesizing insights from the various brainstorming sessions and informal discussions that unfolded during this week of vibrant exchange of ideas. The result of these exchanges takes the form of a series of open questions that represent outstanding experimental, numerical, and theoretical challenges to be tackled in the near future.
△ Less
Submitted 21 December, 2023;
originally announced December 2023.
-
Continuum modeling of Soft Glassy Materials under shear
Authors:
Roberto Benzi,
Thibaut Divoux,
Catherine Barentin,
Sébastien Manneville,
Mauro Sbragaglia,
Federico Toschi
Abstract:
Soft Glassy Materials (SGM) consist in dense amorphous assemblies of colloidal particles of multiple shapes, elasticity, and interactions, which confer upon them solid-like properties at rest. They are ubiquitously encountered in modern engineering, including additive manufacturing, semi-solid flow cells, dip-coating, adhesive locomotion, where they are subjected to complex mechanical histories. S…
▽ More
Soft Glassy Materials (SGM) consist in dense amorphous assemblies of colloidal particles of multiple shapes, elasticity, and interactions, which confer upon them solid-like properties at rest. They are ubiquitously encountered in modern engineering, including additive manufacturing, semi-solid flow cells, dip-coating, adhesive locomotion, where they are subjected to complex mechanical histories. Such processes often include a solid-to-liquid transition induced by large enough shear, which results in complex transient phenomena such as non-monotonic stress responses, i.e., stress overshoot, and spatially heterogeneous flows, e.g., shear-banding or brittle failure. In the present article, we propose a pedagogical introduction to a continuum model based on a spatially-resolved fluidity approach that we recently introduced to rationalize shear-induced yielding in SGMs. Our model, which relies upon non-local effects, quantitatively captures salient features associated with such complex flows, including the rate dependence of the stress overshoot, as well as transient shear-banded flows together with nontrivial scaling laws for fluidization times. This approach offers a versatile framework to account for subtle effects, such as avalanche-like phenomena, or the impact of boundary conditions, which we illustrate by including in our model the elasto-hydrodynamic slippage of soft particles compressed against solid surfaces.
△ Less
Submitted 20 September, 2022;
originally announced September 2022.
-
Continuum modelling of shear start-up in soft glassy materials
Authors:
Roberto Benzi,
Thibaut Divoux,
Catherine Barentin,
Sébastien Manneville,
Mauro Sbragaglia,
Federico Toschi
Abstract:
Yield stress fluids (YSFs) display a dual nature highlighted by the existence of a yield stress such that YSFs are solid below the yield stress, whereas they flow like liquids above it. Under an applied shear rate $\dotγ$, the solid-to-liquid transition is associated with a complex spatiotemporal scenario. Still, the general phenomenology reported in the literature boils down to a simple sequence…
▽ More
Yield stress fluids (YSFs) display a dual nature highlighted by the existence of a yield stress such that YSFs are solid below the yield stress, whereas they flow like liquids above it. Under an applied shear rate $\dotγ$, the solid-to-liquid transition is associated with a complex spatiotemporal scenario. Still, the general phenomenology reported in the literature boils down to a simple sequence that can be divided into a short-time response characterized by the so-called "stress overshoot", followed by stress relaxation towards a steady state. Such relaxation can be either long-lasting, which usually involves the growth of a shear band that can be only transient or that may persist at steady-state, or abrupt, in which case the solid-to-liquid transition resembles the failure of a brittle material, involving avalanches. Here we use a continuum model based on a spatially-resolved fluidity approach to rationalize the complete scenario associated with the shear-induced yielding of YSFs. Our model provides a scaling for the coordinates of the stress maximum as a function of $\dotγ$, which shows excellent agreement with experimental and numerical data extracted from the literature. Moreover, our approach shows that such a scaling is intimately linked to the growth dynamics of a fluidized boundary layer in the vicinity of the moving boundary. Yet, such scaling is independent of the fate of that layer, and of the long-term behavior of the YSF. Finally, when including the presence of "long-range" correlations, we show that our model displays a ductile to brittle transition, i.e., the stress overshoot reduces into a sharp stress drop associated with avalanches, which impacts the scaling of the stress maximum with $\dotγ$. Our work offers a unified picture of shear-induced yielding in YSFs, whose complex spatiotemporal dynamics are deeply connected to non-local effects.
△ Less
Submitted 1 July, 2021; v1 submitted 31 March, 2021;
originally announced March 2021.
-
Stress Overshoots in Simple Yield Stress Fluids
Authors:
Roberto Benzi,
Thibaut Divoux,
Catherine Barentin,
Sébastien Manneville,
Mauro Sbragaglia,
Federico Toschi
Abstract:
Soft glassy materials such as mayonnaise, wet clays, or dense microgels display under external shear a solid-to-liquid transition. Such a shear-induced transition is often associated with a non-monotonic stress response, in the form of a stress maximum referred to as "stress overshoot". This ubiquitous phenomenon is characterized by the coordinates of the maximum in terms of stress $σ_\text{M}$ an…
▽ More
Soft glassy materials such as mayonnaise, wet clays, or dense microgels display under external shear a solid-to-liquid transition. Such a shear-induced transition is often associated with a non-monotonic stress response, in the form of a stress maximum referred to as "stress overshoot". This ubiquitous phenomenon is characterized by the coordinates of the maximum in terms of stress $σ_\text{M}$ and strain $γ_\text{M}$ that both increase as weak power laws of the applied shear rate. Here we rationalize such power-law scalings using a continuum model that predicts two different regimes in the limit of low and high applied shear rates. The corresponding exponents are directly linked to the steady-state rheology and are both associated with the nucleation and growth dynamics of a fluidized region. Our work offers a consistent framework for predicting the transient response of soft glassy materials upon start-up of shear from the local flow behavior to the global rheological observables.
△ Less
Submitted 13 September, 2021; v1 submitted 31 March, 2021;
originally announced March 2021.
-
Unified theoretical and experimental view on transient shear banding
Authors:
Roberto Benzi,
Thibaut Divoux,
Catherine Barentin,
Sébastien Manneville,
Mauro Sbragaglia,
Federico Toschi
Abstract:
Dense emulsions, colloidal gels, microgels, and foams all display a solid-like behavior at rest characterized by a yield stress, above which the material flows like a liquid. Such a fluidization transition often consists of long-lasting transient flows that involve shear-banded velocity profiles. The characteristic time for full fluidization, $τ_\text{f}$, has been reported to decay as a power-law…
▽ More
Dense emulsions, colloidal gels, microgels, and foams all display a solid-like behavior at rest characterized by a yield stress, above which the material flows like a liquid. Such a fluidization transition often consists of long-lasting transient flows that involve shear-banded velocity profiles. The characteristic time for full fluidization, $τ_\text{f}$, has been reported to decay as a power-law of the shear rate $\dot γ$ and of the shear stress $σ$ with respective exponents $α$ and $β$. Strikingly, the ratio of these exponents was empirically observed to coincide with the exponent of the Herschel-Bulkley law that describes the steady-state flow behavior of these complex fluids. Here we introduce a continuum model, based on the minimization of a "free energy", that captures quantitatively all the salient features associated with such \textit{transient} shear-banding. More generally, our results provide a unified theoretical framework for describing the yielding transition and the steady-state flow properties of yield stress fluids.
△ Less
Submitted 2 October, 2019; v1 submitted 20 July, 2019;
originally announced July 2019.
-
Simple ions control the elasticity of calcite gels via interparticle forces
Authors:
Teresa Liberto,
Catherine Barentin,
Jean Colombani,
Anna Costa,
Davide Gardini,
Maurizio Bellotto,
Marie Le Merrer
Abstract:
Suspensions of calcite in water are employed in many industrial fields such as paper filling, pharmaceutics, heritage conservation or building construction, where the rheological properties of the paste need to be controlled. We measure the impact of simple ions such as calcium, sodium or hydroxide on the elasticity of a nanocalcite paste, which behaves as a colloidal gel. We confront our macrosco…
▽ More
Suspensions of calcite in water are employed in many industrial fields such as paper filling, pharmaceutics, heritage conservation or building construction, where the rheological properties of the paste need to be controlled. We measure the impact of simple ions such as calcium, sodium or hydroxide on the elasticity of a nanocalcite paste, which behaves as a colloidal gel. We confront our macroscopic measurements to DLVO interaction potentials, based on chemical speciations and measurements of the zeta potential. By changing the ion type and concentration, we go beyond the small repulsion regime and span two orders of magnitude in shear modulus. Upon addition of calcium hydroxide, we observe a minimum in shear modulus, correlated to a maximum in the DLVO energy barrier, due to two competing effects: Calcium adsorption onto calcite surface rises the zeta potential and consequently the electrostatic repulsion, while increasing salt concentration induces stronger electrostatic screening. We also demonstrate that the addition of sodium hydroxide completely screens the surface charge and leads to a more rigid paste. A second important result is that carbonation of the calcite suspensions by the atmospheric CO 2 leads to a convergent high elasticity of the colloidal gels, whatever their initial value, also well rationalized by DLVO theory and resulting from a decrease in zeta potential and in surface charge density.
△ Less
Submitted 30 April, 2019;
originally announced April 2019.
-
Probing the Fluctuation-Dissipation Theorem in a Perrin-like Experiment
Authors:
Jean Colombani,
Laure Petit,
Christophe Ybert,
Catherine Barentin
Abstract:
In this Letter, we present a new experimental approach to investigate the effective temperature concept as a generalization of the fluctuation-dissipation theorem (FDT) for nonequilibrium systems. Simultaneous measurements of diffusion coefficient and sedimentation velocity of heavy colloids, embedded in a Laponite clay suspension, are performed with a fluorescence-recovery-based setup. This nonpe…
▽ More
In this Letter, we present a new experimental approach to investigate the effective temperature concept as a generalization of the fluctuation-dissipation theorem (FDT) for nonequilibrium systems. Simultaneous measurements of diffusion coefficient and sedimentation velocity of heavy colloids, embedded in a Laponite clay suspension, are performed with a fluorescence-recovery-based setup. This nonperturbative dual measurement, performed at a single time in a single sample, allows for a direct application of the FDT to the tracer velocity observable. It thus provides a well-defined derivation of the effective temperature in this ageing colloidal gel. For a wide range of concentrations and ageing times, we report no violation of the FDT, with effective temperature agreeing with bath temperature. This result is consistent with recent theoretical predictions on the coupling between the velocity observable and nonequilibrium gels dynamics.
△ Less
Submitted 5 December, 2017;
originally announced December 2017.
-
Yield stress and elasticity influence on surface tension measurements
Authors:
Loren Jørgensen,
Marie Le Merrer,
Hélène Delanoë-Ayari,
Catherine Barentin
Abstract:
We have performed surface tension measurements on carbopol gels of different concentrations and yield stresses. Our setup, based on the force exerted by a capillary bridge on two parallel plates, allows to measure an effective surface tension of the complex fluid and to investigate the influence of flow history. More precisely the effective surface tension measured after stretching the bridge is a…
▽ More
We have performed surface tension measurements on carbopol gels of different concentrations and yield stresses. Our setup, based on the force exerted by a capillary bridge on two parallel plates, allows to measure an effective surface tension of the complex fluid and to investigate the influence of flow history. More precisely the effective surface tension measured after stretching the bridge is always higher than after compressing it. The difference between the two values is due to the existence of a yield stress in the fluid. The experimental observations are successfully reproduced with a simple elasto-plastic model. The shape of successive stretching-compression cycles can be described by taking into account the yield stress and the elasticity of the gel. We show that the surface tension $γ_{LV}$ of yield stress fluids is the mean of the effective surface tension values only if the elastic modulus is high compared to the yield stress. This work highlights that thermodynamical quantities measurements are challenged by the fluid out-of-equilibrium state implied by jamming, even at small scales where the shape of the bridge is driven by surface energy. Therefore setups allowing deformation in opposite directions are relevant for measurements on yield stress fluids.
△ Less
Submitted 4 June, 2015;
originally announced June 2015.
-
Scaling laws for slippage on superhydrophobic fractal surfaces
Authors:
C. Cottin-Bizonne,
C. Barentin,
L. Bocquet
Abstract:
We study the slippage on hierarchical fractal superhydrophobic surfaces, and find an unexpected rich behavior for hydrodynamic friction on these surfaces. We develop a scaling law approach for the effective slip length, which is validated by numerical resolution of the hydrodynamic equations. Our results demonstrate that slippage does strongly depend on the fractal dimension, and is found to be al…
▽ More
We study the slippage on hierarchical fractal superhydrophobic surfaces, and find an unexpected rich behavior for hydrodynamic friction on these surfaces. We develop a scaling law approach for the effective slip length, which is validated by numerical resolution of the hydrodynamic equations. Our results demonstrate that slippage does strongly depend on the fractal dimension, and is found to be always smaller on fractal surfaces as compared to surfaces with regular patterns. This shows that in contrast to naive expectations, the value of effective contact angle is not sufficient to infer the amount of slippage on a fractal surface: depending on the underlying geometry of the roughness, strongly superhydrophobic surfaces may in some cases be fully inefficient in terms of drag reduction. Finally, our scaling analysis can be directly extended to the study of heat transfer at fractal surfaces, in order to estimate the Kapitsa surface resistance on patterned surfaces, as well as to the question of trap** of diffusing particles by patchy hierarchical surfaces, in the context of chemoreception.
△ Less
Submitted 24 January, 2012;
originally announced January 2012.
-
Yielding dynamics of a Herschel-Bulkley fluid: a critical-like fluidization behaviour
Authors:
Thibaut Divoux,
David Tamarii,
Catherine Barentin,
Stephen Teitel,
Sébastien Manneville
Abstract:
The shear-induced fluidization of a carbopol microgel is investigated during long start-up experiments using combined rheology and velocimetry in Couette cells of varying gap widths and boundary conditions. As already described in [Divoux et al., {\it Phys. Rev. Lett.}, 2010, {\bf 104}, 208301], we show that the fluidization process of this simple yield stress fluid involves a transient shear-band…
▽ More
The shear-induced fluidization of a carbopol microgel is investigated during long start-up experiments using combined rheology and velocimetry in Couette cells of varying gap widths and boundary conditions. As already described in [Divoux et al., {\it Phys. Rev. Lett.}, 2010, {\bf 104}, 208301], we show that the fluidization process of this simple yield stress fluid involves a transient shear-banding regime whose duration $τ_f$ decreases as a power law of the applied shear rate $\gp$. Here we go one step further by an exhaustive investigation of the influence of the shearing geometry through the gap width $e$ and the boundary conditions. While slip conditions at the walls seem to have a negligible influence on the fluidization time $τ_f$, different fluidization processes are observed depending on $\gp$ and $e$: the shear band remains almost stationary for several hours at low shear rates or small gap widths before strong fluctuations lead to a homogeneous flow, whereas at larger values of $\gp$ or $e$, the transient shear band is seen to invade the whole gap in a much smoother way. Still, the power-law behaviour appears as very robust and hints to critical-like dynamics. To further discuss these results, we propose (i) a qualitative scenario to explain the induction-like period that precedes full fluidization and (ii) an analogy with critical phenomena that naturally leads to the observed power laws if one assumes that the yield point is the critical point of an underlying out-of-equilibrium phase transition.
△ Less
Submitted 23 July, 2013; v1 submitted 8 October, 2011;
originally announced October 2011.
-
Stress overshoot in a simple yield stress fluid: an extensive study combining rheology and velocimetry
Authors:
Thibaut Divoux,
Catherine Barentin,
Sebastien Manneville
Abstract:
We report a large amount of experimental data on the stress overshoot phenomenon which takes place during start-up shear flows in a simple yield stress fluid, namely a carbopol microgel. A combination of classical rheological measurements and ultrasonic velocimetry makes it possible to get physical insights on the transient dynamics of both the stress $σ(t)$ and the velocity field across the gap o…
▽ More
We report a large amount of experimental data on the stress overshoot phenomenon which takes place during start-up shear flows in a simple yield stress fluid, namely a carbopol microgel. A combination of classical rheological measurements and ultrasonic velocimetry makes it possible to get physical insights on the transient dynamics of both the stress $σ(t)$ and the velocity field across the gap of a rough cylindrical Couette cell during the start-up of shear under an applied shear rate $\dotγ$. (i) At small strains ($γ<1$), $σ(t)$ increases linearly and the microgel undergoes homogeneous deformation. (ii) At a time $t_m$, the stress reaches a maximum value $σ_m$ which corresponds to the failure of the microgel and to the nucleation of a thin lubrication layer at the moving wall. (iii) The microgel then experiences a strong elastic recoil and enters a regime of total wall slip while the stress slowly decreases. (iv) Total wall slip gives way to a transient shear-banding phenomenon, which occurs on timescales much longer than that of the stress overshoot and has been described elsewhere [Divoux \textit{et al., Phys. Rev. Lett.}, 2010, \textbf{104}, 208301]. This whole sequence is very robust to concentration changes in the explored range ($0.5 \le C \le 3%$ w/w). We further demonstrate that the maximum stress $σ_m$ and the corresponding strain $γ_m=\dotγt_m$ both depend on the applied shear rate $\dot γ$ and on the waiting time $t_w$ between preshear and shear start-up: they remain roughly constant as long as $\dotγ$ is smaller than some critical shear rate $\dotγ_w\sim 1/t_w$ and they increase as weak power laws of $\dot γ$ for $\dotγ> \dotγ_w$ [...].
△ Less
Submitted 29 June, 2011; v1 submitted 22 April, 2011;
originally announced April 2011.
-
From transient fluidization processes to Herschel-Bulkley behavior in simple yield stress fluids
Authors:
Thibaut Divoux,
Catherine Barentin,
Sébastien Manneville
Abstract:
Stress-induced fluidization of a simple yield stress fluid, namely a carbopol microgel, is addressed through extensive rheological measurements coupled to simultaneous temporally and spatially resolved velocimetry. These combined measurements allow us to rule out any bulk fracture-like scenario during the fluidization process such as that suggested in [Caton {\it et al., Rheol Acta}, 2008, {\bf 47…
▽ More
Stress-induced fluidization of a simple yield stress fluid, namely a carbopol microgel, is addressed through extensive rheological measurements coupled to simultaneous temporally and spatially resolved velocimetry. These combined measurements allow us to rule out any bulk fracture-like scenario during the fluidization process such as that suggested in [Caton {\it et al., Rheol Acta}, 2008, {\bf 47}, 601-607]. On the contrary, we observe that the transient regime from solidlike to liquidlike behaviour under a constant shear stress $σ$ successively involves creep deformation, total wall slip, and shear banding before a homogeneous steady state is reached. Interestingly, the total duration $τ_f$ of this fluidization process scales as $τ_f \propto 1/(σ- σ_c)^β$, where $σ_c$ stands for the yield stress of the microgel, and $β$ is an exponent which only depends on the microgel properties and not on the gap width or on the boundary conditions. Together with recent experiments under imposed shear rate [Divoux {\it et al., Phys. Rev. Lett.}, 2010, {\bf 104}, 208301], this scaling law suggests a route to rationalize the phenomenological Herschel-Bulkley (HB) power-law classically used to describe the steady-state rheology of simple yield stress fluids. In particular, we show that the {\it steady-state} HB exponent appears as the ratio of the two fluidization exponents extracted separately from the {\it transient} fluidization processes respectively under controlled shear rate and under controlled shear stress.
△ Less
Submitted 29 June, 2011; v1 submitted 3 December, 2010;
originally announced December 2010.
-
Transient Shear Banding in a Simple Yield Stress Fluid
Authors:
Thibaut Divoux,
David Tamarii,
Catherine Barentin,
Sébastien Manneville
Abstract:
We report a large set of experimental data which demonstrates that a simple yield stress fluid, i.e. which does not present aging or thixotropy, exhibits transient shear banding before reaching a steady state characterized by a homogeneous, linear velocity profile. The duration of the transient regime decreases as a power law with the applied shear rate $\dotγ$. This power law behavior, observed…
▽ More
We report a large set of experimental data which demonstrates that a simple yield stress fluid, i.e. which does not present aging or thixotropy, exhibits transient shear banding before reaching a steady state characterized by a homogeneous, linear velocity profile. The duration of the transient regime decreases as a power law with the applied shear rate $\dotγ$. This power law behavior, observed here in carbopol dispersions, does not depend on the gap width and on the boundary conditions for a given sample preparation. For $\dotγ\lesssim 0.1$ s$^{-1}$, heterogeneous flows could be observed for as long as 10$^5$ s. These local dynamics account for the ultraslow stress relaxation observed at low shear rates.
△ Less
Submitted 28 February, 2010;
originally announced March 2010.
-
Shear-induced fragmentation of Laponite suspensions
Authors:
Thomas Gibaud,
Catherine Barentin,
Nicolas Taberlet,
Sébastien Manneville
Abstract:
Simultaneous rheological and velocity profile measurements are performed in a smooth Couette geometry on Laponite suspensions seeded with glass microspheres and undergoing the shear-induced solid-to-fluid (or yielding) transition. Under these slippery boundary conditions, a rich temporal behaviour is uncovered, in which shear localization is observed at short times, that rapidly gives way to a h…
▽ More
Simultaneous rheological and velocity profile measurements are performed in a smooth Couette geometry on Laponite suspensions seeded with glass microspheres and undergoing the shear-induced solid-to-fluid (or yielding) transition. Under these slippery boundary conditions, a rich temporal behaviour is uncovered, in which shear localization is observed at short times, that rapidly gives way to a highly heterogeneous flow characterized by intermittent switching from plug-like flow to linear velocity profiles. Such a temporal behaviour is linked to the fragmentation of the initially solid sample into blocks separated by fluidized regions. These solid pieces get progressively eroded over time scales ranging from a few minutes to several hours depending on the applied shear rate $\dotγ$. The steady-state is characterized by a homogeneous flow with almost negligible wall slip. The characteristic time scale for erosion is shown to diverge below some critical shear rate $\dotγ^\star$ and to scale as $(\dotγ-\dotγ^\star)^{-n}$ with $n\simeq 2$ above $\dotγ^\star$. A tentative model for erosion is discussed together with open questions raised by the present results.
△ Less
Submitted 6 April, 2009;
originally announced April 2009.
-
Influence of boundary conditions on yielding in a soft glassy material
Authors:
Thomas Gibaud,
Catherine Barentin,
Sebastien Manneville
Abstract:
The yielding behavior of a sheared Laponite suspension is investigated within a 1 mm gap under two different boundary conditions. No-slip conditions, ensured by using rough walls, lead to shear localization as already reported in various soft glassy materials. When apparent wall slip is allowed using a smooth geometry, the sample is shown to break up into macroscopic solid pieces that get slowly…
▽ More
The yielding behavior of a sheared Laponite suspension is investigated within a 1 mm gap under two different boundary conditions. No-slip conditions, ensured by using rough walls, lead to shear localization as already reported in various soft glassy materials. When apparent wall slip is allowed using a smooth geometry, the sample is shown to break up into macroscopic solid pieces that get slowly eroded by the surrounding fluidized material up to the point where the whole sample is fluid. Such a drastic effect of boundary conditions on yielding suggests the existence of some macroscopic characteristic length that could be connected to cooperativity effects in jammed materials under shear.
△ Less
Submitted 6 January, 2009; v1 submitted 21 July, 2008;
originally announced July 2008.
-
Dynamics of simple liquids at heterogeneous surfaces : Molecular Dynamics simulations and hydrodynamic description
Authors:
Cecile Cottin-Bizonne,
Catherine Barentin,
Elisabeth Charlaix,
Lyderic Bocquet,
Jean-Louis Barrat
Abstract:
In this paper we consider the effect of surface heterogeneity on the slippage of fluid, using two complementary approaches. First, MD simulations of a corrugated hydrophobic surface have been performed. A dewetting transition, leading to a super-hydrophobic state, is observed for pressure below a ``capillary'' pressure. Conversely a very large slippage of the fluid on this composite interface is…
▽ More
In this paper we consider the effect of surface heterogeneity on the slippage of fluid, using two complementary approaches. First, MD simulations of a corrugated hydrophobic surface have been performed. A dewetting transition, leading to a super-hydrophobic state, is observed for pressure below a ``capillary'' pressure. Conversely a very large slippage of the fluid on this composite interface is found in this superhydrophobic state. Second, we propose a macroscopic estimate of the effective slip length on the basis of continuum hydrodynamics, in order to rationalize the previous MD results. This calculation allows to estimate the effect of a heterogeneous slip length pattern on the composite interface. Comparison between the two approaches are in good agreement at low pressure, but highlights the role of the exact shape of the liquid-vapor interface at higher pressure. These results confirm that small variations in the roughness of a surface can lead to huge differences in the slip effect. On the basis of these results, we propose some guidelines to design highly slippery surfaces, motivated by potential applications in microfluidics.
△ Less
Submitted 3 April, 2004;
originally announced April 2004.
