Showing 1–23 of 23 results for author: Bar, T

Fabrication of $^{108}$Cd target for the astrophysical p-process studies

Authors: Sukhendu Saha, Mousri Paul, Lalit Kumar Sahoo, Dipali Basak, Tanmoy Bar, Jagannath Datta, Sandipan Dasgupta, G. L. N. Reddy, Chinmay Basu

Abstract: The detailed process of preparing enriched $^{108}$Cd targets on mylar and copper backing using the vacuum evaporation technique is described. These targets were employed in an experiment to measure the proton capture cross-section at energies significantly below the Coulomb barrier, for the astrophysical p-process studies. Due to the low melting point and high vapor pressure of cadmium, some adju… ▽ More The detailed process of preparing enriched $^{108}$Cd targets on mylar and copper backing using the vacuum evaporation technique is described. These targets were employed in an experiment to measure the proton capture cross-section at energies significantly below the Coulomb barrier, for the astrophysical p-process studies. Due to the low melting point and high vapor pressure of cadmium, some adjustments were implemented in the Telemark multipocket e-beam setup. The target thickness was determined through the measurement of alpha particle energy loss from a triple alpha source and also by RBS measurements. The thickness of the $^{108}$Cd films varies between 290 to 660 $μ$g/cm$^2$, with a non-uniformity of approximately 10$\%$. X-ray Photoelectron Spectroscopy (XPS) and X-ray Fluorescence (XRF) analyses were conducted to examine the presence of impurities and to assess surface morphology, phase, and chemical composition. △ Less

Submitted 19 January, 2024; originally announced February 2024.

First (calibration) experiment using proton beam from FRENA at SINP

Authors: C. Basu, K. Banerjee, T. K. Ghosh, G. Mukherjee, C. Bhattacharya, Shraddha S Desai, R. Shil, A. K. Saha, J. K. Meena, T. Bar, D. Basak, L. K. Sahoo, S. Saha, C. Marick, D. Das, D. Das, D. Das, M. Kujur, S. Roy, S. S. Basu, U. Gond, A. Saha, A. Das, M. Samanta, P. Saha , et al. (1 additional authors not shown)

Abstract: This work presents the first calibration experiment of a 3 MV Tandetron accelerator, FRENA, performed in May 2022. The $^7$Li(p,n) reaction threshold was measured to calibrate the terminal voltage measuring device. A LiF target of thickness 175 $μ$g/cm$^2$ was used in the experiment. The measured threshold was 1872$\pm$2.7 keV, indicating 6$-$10 keV energy shift. This work presents the first calibration experiment of a 3 MV Tandetron accelerator, FRENA, performed in May 2022. The $^7$Li(p,n) reaction threshold was measured to calibrate the terminal voltage measuring device. A LiF target of thickness 175 $μ$g/cm$^2$ was used in the experiment. The measured threshold was 1872$\pm$2.7 keV, indicating 6$-$10 keV energy shift. △ Less

Submitted 24 January, 2024; originally announced February 2024.

Study of $^{113}$In($α,α$) elastic scattering to determine $α$-optical potential relevant for astrophysical $γ$-process

Authors: Dipali Basak, Tanmoy Bar, Lalit Kumar Sahoo, Sukhendu Saha, T. K. Rana, S. Manna, C. Bhattacharya, Samir Kundu, J. K. Sahoo, J. K. Meena, A. K. Saha, Ashok Kumar Mondal, Chinmay Basu

Abstract: The $α$-optical potential is one of the key input parameters used to measure the reaction rate of the ($γ,α$)-process using the Hauser-Feshbach(HF) statistical model and the principle of detailed balance. $α$-elastic scattering experiment on $^{113}$In $p$-nucleus was carried out in the energy range E$_{lab}$=26$-$32 MeV. The vacuum evaporation technique was used to prepare the $^{113}$In target~(… ▽ More The $α$-optical potential is one of the key input parameters used to measure the reaction rate of the ($γ,α$)-process using the Hauser-Feshbach(HF) statistical model and the principle of detailed balance. $α$-elastic scattering experiment on $^{113}$In $p$-nucleus was carried out in the energy range E$_{lab}$=26$-$32 MeV. The vacuum evaporation technique was used to prepare the $^{113}$In target~($\sim$86 $μ$g/cm$^2$). An energy-dependent local optical potential parameters set was obtained by analysing the experimental elastic scattering angular distribution data. The local potential parameters are extrapolated for lower energies and are used to measure the $^{113}$In($α,γ$) reaction cross-section. △ Less

Submitted 15 January, 2024; originally announced January 2024.

Experimental study of $α$-induced reactions on $^{113}$In for astrophysical $p$-process

Authors: Dipali Basak, Tanmoy Bar, Abhijit Roy, Lalit Kumar Sahoo, Sukhendu Saha, Jagannath Datta, Sandipan Dasgupta, Chinmay Basu

Abstract: Neutron deficient nuclei from $^{74}$Se$-^{196}$Hg are thought to be produced by $γ$-induced reactions ($γ$,n), ($γ$,p) and ($γ,α$) processes. The relatively high abundance of $^{113}$In odd A $p$-nuclei has inspired to study its production processes. As reaction with $γ$-beam is difficult to perform in the laboratory, $γ$-induced reaction rate is calculated from the inverse reaction data employin… ▽ More Neutron deficient nuclei from $^{74}$Se$-^{196}$Hg are thought to be produced by $γ$-induced reactions ($γ$,n), ($γ$,p) and ($γ,α$) processes. The relatively high abundance of $^{113}$In odd A $p$-nuclei has inspired to study its production processes. As reaction with $γ$-beam is difficult to perform in the laboratory, $γ$-induced reaction rate is calculated from the inverse reaction data employing reciprocity theorem. Stacked foil activation method was used to measure the $^{113}$In($α,γ$) and $^{113}$In($α$, n) reactions cross-section near the astrophysical energies. Theoretical statistical model calculations were performed with different nuclear input parameters and compared with the experimental results. An appropriate $α$-optical potential has been identified from the ($α,γ$) and ($α$, n) fitting, which provides the major source of uncertainty in the statistical model calculations. The other nuclear input parameters like level density, and $γ$-ray strength function were also constrained for theoretical calculations. $^{113}$In($α,γ$)$^{117}$Sb and $^{117}$Sb($α,γ$)$^{113}$In reaction rates were calculated using best-fitted input parameters. △ Less

Submitted 12 January, 2024; originally announced January 2024.

Measurement of $^{144}$Sm(p,$γ$) cross-section at Gamow energies

Authors: Tanmoy Bar, Dipali Basak, Lalit Kumar Sahoo, Sukhendu Saha, Jagannath Datta, Sandipan Dasgupta, Chinmay Basu

Abstract: The cross-section measurement of $^{144}$Sm(p, $γ$)$^{145}$Eu (T$_{1/2}=$5.93(4) days) reaction has been performed at proton energies around 2.6, 3.1, 3.7, 4.1, 4.2, 4.7, 5.1, 5.5, 5.9, 6.4, 6.8 MeV using the activation technique. These energies correspond to the Gamow window for 3, 4 GK and a partial portion for 2 GK. $^{144}$Sm has been chosen for the present study because of its significantly h… ▽ More The cross-section measurement of $^{144}$Sm(p, $γ$)$^{145}$Eu (T$_{1/2}=$5.93(4) days) reaction has been performed at proton energies around 2.6, 3.1, 3.7, 4.1, 4.2, 4.7, 5.1, 5.5, 5.9, 6.4, 6.8 MeV using the activation technique. These energies correspond to the Gamow window for 3, 4 GK and a partial portion for 2 GK. $^{144}$Sm has been chosen for the present study because of its significantly higher abundance compared to the other neighboring $p$-nuclides (Z $>$ 50). The astrophysical $S-$factor of this reaction has been measured for the first time at E$^{cm}_p=$ 2.57$\pm$0.13 MeV, $S-$ factor$=$2.542$\pm$1.152($\times$10$^{10}$) MeV-b. Cross-section data were compared with the previously measured experimental data from literature and the theoretical predictions obtained using Hauser-Feshbach statistical model codes TALYS 1.96 and NON-SMOKER. A satisfactory agreement between experimental data and theoretical results was observed. Molecular deposition technique was used to prepare the $^{144}$Sm targets having thickness between 100$-$350 $μ$g/cm$^2$ on Al backing. Obtained results were utilized to predict the reaction rates for $^{144}$Sm (p, $γ$) and $^{145}$Eu ($γ$, p) reactions using TALYS 1.96 and the reciprocity theorem. △ Less

Submitted 7 January, 2024; originally announced January 2024.

Geometrical optics of large deviations of Brownian motion in inhomogeneous media

Authors: Tal Bar, Baruch Meerson

Abstract: Geometrical optics provides an instructive insight into Brownian motion, ``pushed" into a large-deviations regime by imposed constraints. Here we extend geometrical optics of Brownian motion by accounting for diffusion inhomogeneity in space. We consider three simple model problems of Brownian motion on the line or in the plane in situations where the diffusivity of the Brownian particle depends o… ▽ More Geometrical optics provides an instructive insight into Brownian motion, ``pushed" into a large-deviations regime by imposed constraints. Here we extend geometrical optics of Brownian motion by accounting for diffusion inhomogeneity in space. We consider three simple model problems of Brownian motion on the line or in the plane in situations where the diffusivity of the Brownian particle depends on one spatial coordinate. One of our results describes ``Brownian refraction": an analog of refraction of light passing through a boundary between two media with different refraction indices. △ Less

Submitted 4 August, 2023; v1 submitted 10 May, 2023; originally announced May 2023.

Comments: 9 pages, 4 figures

Journal ref: J. Stat. Mech. (2023) 093301

Real-time microscopic view of the relaxation of a glass

Authors: Marta Ruiz-Ruiz, Ana Vila-Costa, Tapas Bar, Cristian Rodríguez-Tinoco, Marta Gonzalez-Silveira, Jose Antonio Plaza, Jorge Alcalá, Jordi Fraxedas, Javier Rodriguez-Viejo

Abstract: The understanding of glassy dynamics above the devitrification temperature of a glass remains poorly understood. Here, we use real-time AFM imaging to build a spatio-temporal map of the relaxation dynamics of a highly stable glass into its supercooled liquid. This new methodology enables a direct visualization of the progression of the liquid phase and clarifies and quantifies the presence of loca… ▽ More The understanding of glassy dynamics above the devitrification temperature of a glass remains poorly understood. Here, we use real-time AFM imaging to build a spatio-temporal map of the relaxation dynamics of a highly stable glass into its supercooled liquid. This new methodology enables a direct visualization of the progression of the liquid phase and clarifies and quantifies the presence of localized fast mobility regions separated by giant length scales. Our data permit to establish a clear correlation between dynamic length and time scales in glasses. This approach may also be applicable to unveil the microscopic structure and dynamics of other glass forming systems with much shorter length and time scales, including liquid-cooled glasses. △ Less

Submitted 20 January, 2023; originally announced January 2023.

Critical Slowing Down at the Abrupt Mott Transition: When the First-Order Phase Transition Becomes Zeroth-Order and Looks Like Second-Order

Authors: Satyaki Kundu, Tapas Bar, Rajesh Kumble Nayak, Bhavtosh Bansal

Abstract: We report that the thermally-induced Mott transition in vanadium sesquioxide shows critical-slowing-down and enhanced variance ('critical opalescence') of the order parameter fluctuations measured through low-frequency resistance-noise spectroscopy. Coupled with the observed increase of also the phase-ordering time, these features suggest that the strong abrupt transition is controlled by a critic… ▽ More We report that the thermally-induced Mott transition in vanadium sesquioxide shows critical-slowing-down and enhanced variance ('critical opalescence') of the order parameter fluctuations measured through low-frequency resistance-noise spectroscopy. Coupled with the observed increase of also the phase-ordering time, these features suggest that the strong abrupt transition is controlled by a critical-like singularity in the hysteretic metastable phase. The singularity is identified with the spinodal point and is a likely consequence of the strain-induced long-range interaction. △ Less

Submitted 19 January, 2023; originally announced January 2023.

Comments: 14 pages, 16 figures

Journal ref: Phys. Rev. Lett. 124, 095703 (2020)

Compatible director fields in $\mathbb{R}^3$

Authors: Luiz C. B. da Silva, Tal Bar, Efi Efrati

Abstract: The geometry and interactions between the constituents of a liquid crystal, which are responsible for inducing the partial order in the fluid, may locally favor an attempted phase that could not be realized in $\mathbb{R}^3$. While states that are incompatible with the geometry of $\mathbb{R}^3$ were identified more than 50 years ago, the collection of compatible states remained poorly understood… ▽ More The geometry and interactions between the constituents of a liquid crystal, which are responsible for inducing the partial order in the fluid, may locally favor an attempted phase that could not be realized in $\mathbb{R}^3$. While states that are incompatible with the geometry of $\mathbb{R}^3$ were identified more than 50 years ago, the collection of compatible states remained poorly understood and not well characterized. Recently, the compatibility conditions for three-dimensional director fields were derived using the method of moving frames. These compatibility conditions take the form of six differential relations in five scalar fields locally characterizing the director field. In this work, we rederive these equations using a more transparent approach employing vector calculus. We then use these equations to characterize a wide collection of compatible phases. △ Less

Submitted 14 February, 2023; v1 submitted 15 November, 2022; originally announced November 2022.

Comments: 37 pages (32 in the published version), 5 figures. Keywords: Geometric frustration, Incompatibility, Liquid crystal, Frobenius. Note: This version is essentially the same as the published one. In addition, it is part of a Collection: Soft Matter Elasticity (https://link.springer.com/collections/ijhficbgii)

MSC Class: 53Z05; 35F50; 53A45; 53A55; 53B50

Journal ref: Journal of Elasticity (2023)

Finite-dimensional signature of spinodal instability in an athermal hysteretic transition

Authors: Anurag Banerjee, Tapas Bar

Abstract: We study the off-equilibrium critical phenomena across a hysteretic first-order transition in disordered athermal systems. The study focuses on the zero temperature random field Ising model (ZTRFIM) above the critical disorder for spatial dimensions $d=2,3,$ and $4$. We use Monte Carlo simulations to show that disorder suppresses critical slowing down in phase ordering time for finite-dimensional… ▽ More We study the off-equilibrium critical phenomena across a hysteretic first-order transition in disordered athermal systems. The study focuses on the zero temperature random field Ising model (ZTRFIM) above the critical disorder for spatial dimensions $d=2,3,$ and $4$. We use Monte Carlo simulations to show that disorder suppresses critical slowing down in phase ordering time for finite-dimensional systems. The dynamic hysteresis scaling, the measure of explicit finite-time scaling, is used to subsequently quantify the critical slowing down. The scaling exponents in all dimensions increase with disorder strength and finally reach a stable value where the transformation is no longer critical. The associated critical behavior in the mean-field limit is very different, where the exponent values for various disorders in all dimensions are similar. The non-mean-field exponents asymptotically approach the mean-field value ($Υ\approx 2/3$) with increase in dimensions. The results suggest that the critical features in the hysteretic metastable phase are controlled by inherent mean-field spinodal instability that gets blurred by disorder in low-dimension athermal systems. △ Less

Submitted 12 January, 2023; v1 submitted 8 October, 2022; originally announced October 2022.

Comments: 10 pages, 7 figures

Journal ref: Phys. Rev. B 107, 024103 (2023)

Investigation of long lived activity produced due to neutron emitting reactions

Authors: Tanmoy Bar, Dipali Basak, Sukhendu Saha, Lalit Kumar Sahoo, Chinmay Basu

Abstract: In this article, a detailed investigation has been done for the long lived gamma activity due to neutron emitting experiments. These calculations mainly focused on the experiments used for energy calibration purposes. Calibrated energy is one of the most essential features of any accelerator facility. Several experiments have been used for this purpose. Generally, experiments having sharp curvatur… ▽ More In this article, a detailed investigation has been done for the long lived gamma activity due to neutron emitting experiments. These calculations mainly focused on the experiments used for energy calibration purposes. Calibrated energy is one of the most essential features of any accelerator facility. Several experiments have been used for this purpose. Generally, experiments having sharp curvature change in cross section of yield are used. Neutron emitting experiments are one of such. Around the globe reactions like $^7Li(p,n)$, $^{13}C(p,n)$, $^{19}F(p,n)$, $^{27}Al(p,n)$ etc. are used to calibrate energy of the beam with accelerator terminal voltage. Neutrons coming from these experiments can interact with surrounding elements. These interactions with neutrons can create long lived gamma activity which may interfere with future measurements. The present study has been done kee** in mind the new Facility for Research in Experimental Nuclear Astrophysics (FRENA) at Saha Institute of Nuclear Physics. It is a 3MV tandetron low energy high current machine. △ Less

Submitted 3 March, 2022; originally announced March 2022.

Absolute calibration of the latent heat of transition using differential thermal analysis

Authors: Tapas Bar, Bhavtosh Bansal

Abstract: We describe a simple and accurate differential thermal analysis set up to measure the latent heat of solid state materials undergoing abrupt phase transitions in the temperature range from 77 K to above room temperature. We report a numerical technique for the absolute calibration of the latent heat of the transition, without the need of a reference sample. The technique is applied to three differ… ▽ More We describe a simple and accurate differential thermal analysis set up to measure the latent heat of solid state materials undergoing abrupt phase transitions in the temperature range from 77 K to above room temperature. We report a numerical technique for the absolute calibration of the latent heat of the transition, without the need of a reference sample. The technique is applied to three different samples -- vanadium sesquioxide undergoing the Mott transition, bismuth barium ruthenate undergoing a magnetoelastic transition, and an intermetallic Heusler compound. In each case, the inferred latent heat value agrees with the literature value to within its error margins. To further demonstrate the importance of absolute calibration, we show that the changes in the latent heat of the Mott transition in vanadium sesquioxide (V$_2$O$_3$) stays constant to within 2% even as the depth of supersaturation changes by about 10 K, in non-equilibrium dynamic hysteresis measurements. We also apply this technique for the measurement of the temperature-dependent specific heat. △ Less

Submitted 11 October, 2021; originally announced October 2021.

Comments: This article may be downloaded for personal use only. Any other use requires prior permission of the author and AIP Publishing. This article appeared in Review of Scientific Instruments (volume 92, Issue 7) and may be found at this link (https://doi.org/10.1063/5.0056857)

Journal ref: Volume 92, number = 7, pages = 075106, year = 2021

Parallel Minimum Spanning Forest Computation using Sparse Matrix Kernels

Authors: Tim Baer, Raghavendra Kanakagiri, Edgar Solomonik

Abstract: Formulations of graph algorithms using sparse linear algebra have yielded highly scalable distributed algorithms for problems such as connectivity and shortest path computation. We develop the first formulation of the Awerbuch-Shiloach parallel minimum spanning forest (MSF) algorithm using linear algebra primitives. We introduce a multilinear kernel that operates on an adjacency matrix and two vec… ▽ More Formulations of graph algorithms using sparse linear algebra have yielded highly scalable distributed algorithms for problems such as connectivity and shortest path computation. We develop the first formulation of the Awerbuch-Shiloach parallel minimum spanning forest (MSF) algorithm using linear algebra primitives. We introduce a multilinear kernel that operates on an adjacency matrix and two vectors. This kernel updates graph vertices by simultaneously using information from both adjacent edges and vertices. In addition, we explore optimizations to accelerate the shortcutting step in the Awerbuch-Shiloach algorithm. We implement this MSF algorithm with Cyclops, a distributed-memory library for generalized sparse tensor algebra. We analyze the parallel scalability of our implementation on the Stampede2 supercomputer. △ Less

Submitted 14 December, 2021; v1 submitted 10 October, 2021; originally announced October 2021.

Suppression of spinodal instability by disorder in an athermal system

Authors: Tapas Bar, Arup Ghosh, Anurag Banerjee

Abstract: We observed asymmetric critical slowing down and asymmetric dynamical scaling exponent in the superheating and supercooling kinetic processes during the thermally-induced metal-insulator transition of MnNiSn based heusler alloy. During the transition to the insulator phase, the critical-like features get enhanced compared to the transition back to the metal phase. These experimental findings sugge… ▽ More We observed asymmetric critical slowing down and asymmetric dynamical scaling exponent in the superheating and supercooling kinetic processes during the thermally-induced metal-insulator transition of MnNiSn based heusler alloy. During the transition to the insulator phase, the critical-like features get enhanced compared to the transition back to the metal phase. These experimental findings suggest that the metastable phase in the cooling branch of hysteresis has approached close to the spinodal instability. On the other hand, the extended disorder, generated over and above the intrinsic crystal defects during heating, triggers the excess heterogeneous nucleation before reaching the spinodal point. Zero temperature random field Ising model (ZTRFIM) simulation, inscribed for the athermal martensitic transitions, support the argument that the disorder smears the spinodal instabilities as the correlation length is bounded by the average distance between the disorder points. △ Less

Submitted 12 January, 2023; v1 submitted 22 February, 2021; originally announced February 2021.

Comments: 12 pages, 16 figures

Journal ref: Phys. Rev. B 104, 144102 (2021)

Text-to-speech for the hearing impaired

Authors: Josef Schlittenlacher, Thomas Baer

Abstract: Text-to-speech (TTS) systems offer the opportunity to compensate for a hearing loss at the source rather than correcting for it at the receiving end. This removes limitations such as time constraints for algorithms that amplify a sound in a hearing aid and can lead to higher speech quality. We propose an algorithm that restores loudness to normal perception at a high resolution in time, frequency… ▽ More Text-to-speech (TTS) systems offer the opportunity to compensate for a hearing loss at the source rather than correcting for it at the receiving end. This removes limitations such as time constraints for algorithms that amplify a sound in a hearing aid and can lead to higher speech quality. We propose an algorithm that restores loudness to normal perception at a high resolution in time, frequency and level, and embed it in a TTS system that uses Tacotron2 and WaveGlow to produce individually amplified speech. Subjective evaluations of speech quality showed that the proposed algorithm led to high-quality audio with sound quality similar to original or linearly amplified speech but considerably higher speech intelligibility in noise. Transfer learning led to a quick adaptation of the produced spectra from original speech to individually amplified speech, resulted in high speech quality and intelligibility, and thus gives us a way to train an individual TTS system efficiently. △ Less

Submitted 22 March, 2021; v1 submitted 3 December, 2020; originally announced December 2020.

A simple method to prepare deuterated targets for experiments relevant to nuclear astrophysics

Authors: Tanmoy Bar, Chinmay Basu

Abstract: In this work, a simple and efficient thin ($50- 350μg/cm^2$) deuterated polyethylene target preparation method is described. The method of easy removal of thin targets from casting surface without using any cryogenic freezing has been described. The difference in thermal expansion properties is used to separate films from glass slides. 3-$α$ radioactive source is used to measure the target thickne… ▽ More In this work, a simple and efficient thin ($50- 350μg/cm^2$) deuterated polyethylene target preparation method is described. The method of easy removal of thin targets from casting surface without using any cryogenic freezing has been described. The difference in thermal expansion properties is used to separate films from glass slides. 3-$α$ radioactive source is used to measure the target thickness. The material property of the prepared targets is verified by Attenuated total reflection (ATR) method. △ Less

Submitted 19 August, 2020; v1 submitted 12 April, 2020; originally announced April 2020.

Simulation of heat transfer and dissipation in targets used in nuclear astrophysics experiments

Authors: Tanmoy Bar, Chinmay Basu, Mithun Das, Apurba Kumar Santra, Swarnendu Sen

Abstract: This work presents time-dependent numerical calculations of heat generation and dissipation in targets used in high ion-beam current nuclear astrophysics experiments. The simulation is beneficial for choosing the thickness of targets, maximum ion-beam current and design setup for cooling of such targets. It is found that for the very thin target ($^{27}Al(p,p),^{12}C(p,p)$) heat generation inside… ▽ More This work presents time-dependent numerical calculations of heat generation and dissipation in targets used in high ion-beam current nuclear astrophysics experiments. The simulation is beneficial for choosing the thickness of targets, maximum ion-beam current and design setup for cooling of such targets. It is found that for the very thin target ($^{27}Al(p,p),^{12}C(p,p)$) heat generation inside target is relatively low and a fair amount of high current (few $μ$A)can be used without any melting issue. But in case of thick targets ($^{27}Al(p,γ),^{12}C(p,γ)$) cooling became essential for the survival of reaction target. △ Less

Submitted 24 February, 2020; originally announced February 2020.

The determination of α-spectroscopic factors and ANC of 16O states using 12C(20Ne,16O)16O reaction at Elab=150 MeV incident energy

Authors: Ashok Kumar Mondal, C. Basu, S. Adhikari, C. Bhattacharya, T. K. Rana, S. Kundu, S. Manna, R. Pandey, P. Roy, A. Sen, J. K. Meena, A. K. Saha, J. K. Sahoo, Dipali Basak, Tanmay Bar, Haridas Pai, A. Bisoi, A. K. Mitra, Piyasi Biswas

Abstract: The 12C(20Ne,16O)16O α-transfer reaction at Elab=150 MeV is first time used to determine the ANC of the 6.92 MeV and 7.12 MeV states of 16O. The 20Ne+ 12C potential parameters are also obtained from elastic scattering. The direct reaction code FRESCO is used to determine the α-spectroscopy factor (Sα ) of the three states of 16O (6.92 MeV, 7.12 MeV and 11.52 MeV) and ANC of the two states (6.92 Me… ▽ More The 12C(20Ne,16O)16O α-transfer reaction at Elab=150 MeV is first time used to determine the ANC of the 6.92 MeV and 7.12 MeV states of 16O. The 20Ne+ 12C potential parameters are also obtained from elastic scattering. The direct reaction code FRESCO is used to determine the α-spectroscopy factor (Sα ) of the three states of 16O (6.92 MeV, 7.12 MeV and 11.52 MeV) and ANC of the two states (6.92 MeV and 7.12 MeV) of 16O. The extracted ANC and Sα are compareable to previous measurements. △ Less

Submitted 9 January, 2020; originally announced January 2020.

Comments: 8 pages and 18 figures

Report number: 2001.02873

Kinetic Spinodal Instabilities in the Mott Transition in V2O3: Evidence from Hysteresis Scaling and Dissipative Phase Ordering

Authors: Tapas Bar, Sujeet Kumar Choudhary, Md. Arsalan Ashraf, K. S. Sujith, Sanjay Puri, Satyabrata Raj, Bhavtosh Bansal

Abstract: We present the first systematic observation of scaling of thermal hysteresis with the temperature scanning rate around an abrupt thermodynamic transition in correlated electron systems. We show that the depth of supercooling and superheating in vanadium sesquioxide (V2O3) shifts with the temperature quench rates. The dynamic scaling exponent is close to the mean field prediction of 2/3. These obse… ▽ More We present the first systematic observation of scaling of thermal hysteresis with the temperature scanning rate around an abrupt thermodynamic transition in correlated electron systems. We show that the depth of supercooling and superheating in vanadium sesquioxide (V2O3) shifts with the temperature quench rates. The dynamic scaling exponent is close to the mean field prediction of 2/3. These observations, combined with the purely dissipative continuous ordering seen in "quench-and-hold" experiments, indicate departures from classical nucleation theory toward a barrier-free phase ordering associated with critical dynamics. Observation of critical-like features and scaling in a thermally induced abrupt phase transition suggests that the presence of a spinodal-like instability is not just an artifact of the mean field theories but can also exist in the transformation kinetics of real systems, surviving fluctuations. △ Less

Submitted 2 August, 2018; originally announced August 2018.

Comments: 15 pages, includes supplemental material

Journal ref: Phys. Rev. Lett. 121, 045701 (2018)

Machine Protection, Interlocks and Availability

Authors: A. Apollonio, T. Baer, K. Dahlerup-Petersen, R. Denz, I. Romera Ramirez, R. Schmidt, A. Siemko, J. Wenninger, D. Wollmann, M. Zerlauth

Abstract: Chapter 7 in High-Luminosity Large Hadron Collider (HL-LHC) : Preliminary Design Report. The Large Hadron Collider (LHC) is one of the largest scientific instruments ever built. Since opening up a new energy frontier for exploration in 2010, it has gathered a global user community of about 7,000 scientists working in fundamental particle physics and the physics of hadronic matter at extreme temper… ▽ More Chapter 7 in High-Luminosity Large Hadron Collider (HL-LHC) : Preliminary Design Report. The Large Hadron Collider (LHC) is one of the largest scientific instruments ever built. Since opening up a new energy frontier for exploration in 2010, it has gathered a global user community of about 7,000 scientists working in fundamental particle physics and the physics of hadronic matter at extreme temperature and density. To sustain and extend its discovery potential, the LHC will need a major upgrade in the 2020s. This will increase its luminosity (rate of collisions) by a factor of five beyond the original design value and the integrated luminosity (total collisions created) by a factor ten. The LHC is already a highly complex and exquisitely optimised machine so this upgrade must be carefully conceived and will require about ten years to implement. The new configuration, known as High Luminosity LHC (HL-LHC), will rely on a number of key innovations that push accelerator technology beyond its present limits. Among these are cutting-edge 11-12 tesla superconducting magnets, compact superconducting cavities for beam rotation with ultra-precise phase control, new technology and physical processes for beam collimation and 300 metre-long high-power superconducting links with negligible energy dissipation. The present document describes the technologies and components that will be used to realise the project and is intended to serve as the basis for the detailed engineering design of HL-LHC. △ Less

Submitted 26 May, 2017; originally announced May 2017.

Comments: 10 pages, chapter 7 in High-Luminosity Large Hadron Collider (HL-LHC) : Preliminary Design Report

Journal ref: CERN Yellow Report CERN 2015-005, pp. 147-156

An In Vitro Nematic Model for Proliferating Cell Cultures

Authors: Sunil Pai, Nathan Loewke, Morgaine Green, Christine Cordeiro, Elise Cabral, Bertha Chen, Thomas Baer

Abstract: Confluent populations of elongated cells give rise to ordered patterns seen in nematic phase liquid crystals. We correlate cell elongation and intercellular distance with intercellular alignment using an amorphous spin glass model. We compare in vitro time-lapse imaging with Monte Carlo simulation results by framing a novel hard ellipses model in terms of Boltzmann statistics. Furthermore, we find… ▽ More Confluent populations of elongated cells give rise to ordered patterns seen in nematic phase liquid crystals. We correlate cell elongation and intercellular distance with intercellular alignment using an amorphous spin glass model. We compare in vitro time-lapse imaging with Monte Carlo simulation results by framing a novel hard ellipses model in terms of Boltzmann statistics. Furthermore, we find a statistically distinct alignment energy at quasi-steady state among fibroblasts, smooth muscle cells, and pluripotent cell populations when cultured in vitro. These findings have important implications in both non-invasive clinical screening of the stem cell differentiation process and in relating shape parameters to coupling in active crystal systems such as nematic cell monolayers. △ Less

Submitted 25 November, 2016; originally announced November 2016.

Testing Beam-Induced Quench Levels of LHC Superconducting Magnets

Authors: B. Auchmann, T. Baer, M. Bednarek, G. Bellodi, C. Bracco, R. Bruce, F. Cerutti, V. Chetvertkova, B. Dehning, P. P. Granieri, W. Hofle, E. B. Holzer, A. Lechner, E. Nebot Del Busto, A. Priebe, S. Redaelli, B. Salvachua, M. Sapinski, R. Schmidt, N. Shetty, E. Skordis, M. Solfaroli, J. Steckert, D. Valuch, A. Verweij , et al. (3 additional authors not shown)

Abstract: In the years 2009-2013 the Large Hadron Collider (LHC) has been operated with the top beam energies of 3.5 TeV and 4 TeV per proton (from 2012) instead of the nominal 7 TeV. The currents in the superconducting magnets were reduced accordingly. To date only seventeen beam-induced quenches have occurred; eight of them during specially designed quench tests, the others during injection. There has not… ▽ More In the years 2009-2013 the Large Hadron Collider (LHC) has been operated with the top beam energies of 3.5 TeV and 4 TeV per proton (from 2012) instead of the nominal 7 TeV. The currents in the superconducting magnets were reduced accordingly. To date only seventeen beam-induced quenches have occurred; eight of them during specially designed quench tests, the others during injection. There has not been a single beam- induced quench during normal collider operation with stored beam. The conditions, however, are expected to become much more challenging after the long LHC shutdown. The magnets will be operating at near nominal currents, and in the presence of high energy and high intensity beams with a stored energy of up to 362 MJ per beam. In this paper we summarize our efforts to understand the quench levels of LHC superconducting magnets. We describe beam-loss events and dedicated experiments with beam, as well as the simulation methods used to reproduce the observable signals. The simulated energy deposition in the coils is compared to the quench levels predicted by electro-thermal models, thus allowing to validate and improve the models which are used to set beam-dump thresholds on beam-loss monitors for Run 2. △ Less

Submitted 26 June, 2015; v1 submitted 18 February, 2015; originally announced February 2015.

Comments: 19 pages

Journal ref: Phys. Rev. ST Accel. Beams 18, 061002 (2015)

Camera identification by grou** images from database, based on shared noise patterns

Authors: Teun Baar, Wiger van Houten, Zeno Geradts

Abstract: Previous research showed that camera specific noise patterns, so-called PRNU-patterns, are extracted from images and related images could be found. In this particular research the focus is on grou** images from a database, based on a shared noise pattern as an identification method for cameras. Using the method as described in this article, groups of images, created using the same camera, could… ▽ More Previous research showed that camera specific noise patterns, so-called PRNU-patterns, are extracted from images and related images could be found. In this particular research the focus is on grou** images from a database, based on a shared noise pattern as an identification method for cameras. Using the method as described in this article, groups of images, created using the same camera, could be linked from a large database of images. Using MATLAB programming, relevant image noise patterns are extracted from images much quicker than common methods by the use of faster noise extraction filters and improvements to reduce the calculation costs. Relating noise patterns, with a correlation above a certain threshold value, can quickly be matched. Hereby, from a database of images, groups of relating images could be linked and the method could be used to scan a large number of images for suspect noise patterns. △ Less

Submitted 12 July, 2012; v1 submitted 11 July, 2012; originally announced July 2012.