-
Soil Erosion in the United States. Present and Future (2020-2050)
Authors:
Shahab Aldin Shojaeezadeh,
Malik Al-Wardy,
Mohammad Reza Nikoo,
Mehrdad Ghorbani Mooselu,
Mohammad Reza Alizadeh,
Jan Franklin Adamowski,
Hamid Moradkhani,
Nasrin Alamdari,
Amir H. Gandomi
Abstract:
Soil erosion is a significant threat to the environment and long-term land management around the world. Accelerated soil erosion by human activities inflicts extreme changes in terrestrial and aquatic ecosystems, which is not fully surveyed/predicted for the present and probable future at field-scales (30-m). Here, we estimate/predict soil erosion rates by water erosion, (sheet and rill erosion),…
▽ More
Soil erosion is a significant threat to the environment and long-term land management around the world. Accelerated soil erosion by human activities inflicts extreme changes in terrestrial and aquatic ecosystems, which is not fully surveyed/predicted for the present and probable future at field-scales (30-m). Here, we estimate/predict soil erosion rates by water erosion, (sheet and rill erosion), using three alternative (2.6, 4.5, and 8.5) Shared Socioeconomic Pathway and Representative Concentration Pathway (SSP-RCP) scenarios across the contiguous United States. Field Scale Soil Erosion Model (FSSLM) estimations rely on a high resolution (30-m) G2 erosion model integrated by satellite- and imagery-based estimations of land use and land cover (LULC), gauge observations of long-term precipitation, and scenarios of the Coupled Model Intercomparison Project Phase 6 (CMIP6). The baseline model (2020) estimates soil erosion rates of 2.32 Mg ha 1 yr 1 with current agricultural conservation practices (CPs). Future scenarios with current CPs indicate an increase between 8% to 21% under different combinations of SSP-RCP scenarios of climate and LULC changes. The soil erosion forecast for 2050 suggests that all the climate and LULC scenarios indicate either an increase in extreme events or a change in the spatial location of extremes largely from the southern to the eastern and northeastern regions of the United States.
△ Less
Submitted 13 July, 2022;
originally announced July 2022.
-
Precipitate strengthening of pyramidal slip in Mg-Zn alloys
Authors:
Reza Alizadeh,
**gya Wang,
Javier LLorca
Abstract:
The mechanical properties of Mg-4wt.% Zn alloy single crystals along the [0001] orientation were measured through micropillar compression at 23C and 100C. Basal slip was dominant in the solution treated alloy, while pyramidal slip occurred in the precipitation hardened alloy. Pyramidal dislocations pass the precipitates by forming Orowan loops, leading to homogeneous deformation and to a strong ha…
▽ More
The mechanical properties of Mg-4wt.% Zn alloy single crystals along the [0001] orientation were measured through micropillar compression at 23C and 100C. Basal slip was dominant in the solution treated alloy, while pyramidal slip occurred in the precipitation hardened alloy. Pyramidal dislocations pass the precipitates by forming Orowan loops, leading to homogeneous deformation and to a strong hardening. The predictions of the yield stress based on the Orowan model were in reasonable agreement with the experimental data. The presence of rod-shape precipitates perpendicular to the basal plane leads to a strong reduction in the plastic anisotropy of Mg.
△ Less
Submitted 20 December, 2020;
originally announced December 2020.
-
Atomistic simulations of the interaction of basal dislocations with MgZn$_2$ precipitates in Mg alloys
Authors:
G. Esteban-Manzanares,
R. Alizadeh,
I. Papadimitriou,
D. Dickel,
C. D. Barrett,
J. LLorca
Abstract:
The interaction between Mg edge basal dislocations and rod-shaped $β_1'$-MgZn$_2$ precipitates was studied by atomistic simulations using a new interatomic potential. The atomistic model was carefully built taking into account the experimental information about the orientation relationship between the matrix and the precipitate to ensure minimum energy interfaces. It was found that the dislocation…
▽ More
The interaction between Mg edge basal dislocations and rod-shaped $β_1'$-MgZn$_2$ precipitates was studied by atomistic simulations using a new interatomic potential. The atomistic model was carefully built taking into account the experimental information about the orientation relationship between the matrix and the precipitate to ensure minimum energy interfaces. It was found that the dislocations initially overcame the precipitate by the formation of an Orowan loop that penetrated in the precipitate. The precipitate was finally sheared after several Orowan loops were piled-up. The number of loops necessary to shear the precipitate decreased as precipitate cross-section decreased and the temperature increased but was independent of the precipitate spacing. Precipitate shearing did not take place along well-defined crystallographic planes but it was triggered by the accumulation of the elastic energy in the precipitate which finally led to formation of an amorphous layer below and above the slip plane of the basal dislocations. The kink induced in the precipitate by this mechanism was in good agreement with transmission electron microscopy observations.
△ Less
Submitted 9 May, 2020;
originally announced May 2020.
-
Interactions between basal dislocations and $β_1'$ precipitates in Mg-4Zn alloy: mechanisms and strengthening
Authors:
R. Alizadeh,
J. LLorca
Abstract:
The mechanisms of dislocation/precipitate interaction as well as the critical resolved shear stress were determined as a function of temperature in a Mg-4 wt. % Zn alloy by means of micropillar compression tests. It was found that the mechanical properties were independent of the micropillar size when the cross-section was $>$ 3 x 3 $μ$m$^2$. Transmission electron microscopy showed that deformatio…
▽ More
The mechanisms of dislocation/precipitate interaction as well as the critical resolved shear stress were determined as a function of temperature in a Mg-4 wt. % Zn alloy by means of micropillar compression tests. It was found that the mechanical properties were independent of the micropillar size when the cross-section was $>$ 3 x 3 $μ$m$^2$. Transmission electron microscopy showed that deformation involved a mixture of dislocation bowing around the precipitates and precipitate shearing. The initial yield strength was compatible with the predictions of the Orowan model for dislocation bowing around the precipitates. Nevertheless, precipitate shearing was dominant afterwards, leading to the formation of slip bands in which the rod precipitates were transformed into globular particles, limiting the strain hardening. The importance of precipitate shearing increased with temperature and was responsible for the reduction in the mechanical properties of the alloy from 23C to 100C.
△ Less
Submitted 13 January, 2020;
originally announced January 2020.
-
A criterion for slip transfer at grain boundaries in Al
Authors:
R. Alizadeh,
M. Peña-Ortega,
T. R. Bieler,
J. LLorca
Abstract:
The slip transfer phenomenon was studied at the grain boundaries of pure Aluminum by means of slip trace analysis. Either slip transfer or blocked slip was analyzed in more than 250 grain boundaries and the likelihood of slip transfer between two slip systems across the boundary was assessed. The experimental results indicate that slip transfer was very likely to occur if the residual Burgers vect…
▽ More
The slip transfer phenomenon was studied at the grain boundaries of pure Aluminum by means of slip trace analysis. Either slip transfer or blocked slip was analyzed in more than 250 grain boundaries and the likelihood of slip transfer between two slip systems across the boundary was assessed. The experimental results indicate that slip transfer was very likely to occur if the residual Burgers vector, $Δ$b, was below 0.35b and the Luster- Morris parameter was higher than 0.9, and that the ratio of the Luster-Morris parameter and the residual Burgers vector has a threshold above which slip transfer is probable.
△ Less
Submitted 5 December, 2019;
originally announced December 2019.
-
Effect of slip transmission at grain boundaries in Al bicrystals
Authors:
S. Haouala,
R. Alizadeh,
T. R. Bieler,
J. Segurado,
J. LLorca
Abstract:
The effect of slip transfer on the deformation mechanisms of Al bicrystals was explored using a rate-dependent dislocation-based crystal plasticity model. Three different types of grain boundaries (GBs) were included in the model by modifying the rate of dislocation accumulation near the GB in the Kocks-Mecking law, leading to fully-opaque (dislocation blocking), fully-transparent and partially-tr…
▽ More
The effect of slip transfer on the deformation mechanisms of Al bicrystals was explored using a rate-dependent dislocation-based crystal plasticity model. Three different types of grain boundaries (GBs) were included in the model by modifying the rate of dislocation accumulation near the GB in the Kocks-Mecking law, leading to fully-opaque (dislocation blocking), fully-transparent and partially-transparent GBs. In the latter, slip transmission is only allowed in pairs of SS in neighbour grains that are suitably oriented for slip transfer according to the Luster-Morris parameter. Modifications of the GB character led to important changes in the deformation mechanisms at the GB. In general, bicrystals with fully-opaque boundaries showed an increase in the dislocation density near the GB, which was associated with an increase in the Von Mises stress. In contrast, the dislocation pile-ups and the stress concentration were less pronounced in the case of partially-transparent boundaries as the slip in one grain can progress into the next grain with some degree of continuity. No stress concentrations were found at these boundaries for fully-transparent boundaries, and there was continuity of strain across the boundary, which is not typical of most experimentally observed GBs. Simulations of ideal bicrystals oriented for favorable slip transfer on the most highly favored slip system in grains with high Schmid factors for slip transfer depends on the number of active SS in operation in the neighborhood and that most boundaries will lead to nearly opaque conditions while some boundaries will be transparent. Finally, the model was applied to a particular experimentally observed GB in which slip transfer was clearly operating indicating that the model predicted a nearly transparent GB.
△ Less
Submitted 7 September, 2019;
originally announced September 2019.
-
Effect of solute content and temperature on the deformation mechanisms and critical resolved shear stress in Mg-Al and Mg-Zn alloys
Authors:
J-Y. Wang,
N. Li,
R. Alizadeh,
M. A. Monclús,
Y. W. Cui,
J. M. Molina-Aldareguía,
J. LLorca
Abstract:
The influence of solute atoms (Al and Zn) on the deformation mechanisms and the critical resolved shear stress for basal slip in Mg alloys at 298 K and 373 K was ascertained by micropillar compression tests in combination with high-throughput processing techniques based on the diffusion couples. It was found that the presence of solute atoms enhances the size effect at 298 K as well as the localiz…
▽ More
The influence of solute atoms (Al and Zn) on the deformation mechanisms and the critical resolved shear stress for basal slip in Mg alloys at 298 K and 373 K was ascertained by micropillar compression tests in combination with high-throughput processing techniques based on the diffusion couples. It was found that the presence of solute atoms enhances the size effect at 298 K as well as the localization of deformation in slip bands, which is associated with large strain bursts in the resolved shear stress ($τ_{RSS}$)-strain ($ε$) curves. Deformation in pure Mg and Mg alloys was more homogeneous at 373 K and the influence of the micropillar size on the critical resolved shear stress was much smaller. In this latter case, it was possible to determine the effect of solute content on the critical resolved shear stress for basal slip in Mg-Al and Mg-Zn alloys.
△ Less
Submitted 20 March, 2019;
originally announced March 2019.
-
An analysis of (the lack of) slip transfer between near-cube oriented grains in pure Al
Authors:
T. R Bieler,
R. Alizadeh,
M. Peña-Ortega,
J. LLorca
Abstract:
Slip transfer across grain boundaries was studied in annealed polycrystalline Al foils deformed in uniaxial tension by means of the analysis of the slip traces on the specimen surface. Grain orientations and selected grain boundary misorientations were measured on both surfaces of the sample using electron back-scattered diffraction map**. It was found that most of the grains were within 15° of…
▽ More
Slip transfer across grain boundaries was studied in annealed polycrystalline Al foils deformed in uniaxial tension by means of the analysis of the slip traces on the specimen surface. Grain orientations and selected grain boundary misorientations were measured on both surfaces of the sample using electron back-scattered diffraction map**. It was found that most of the grains were within 15° of a cube orientation and approximately half of the grains percolated through the specimen thickness. The Luster-Morris m' parameter (that can be computed from the surface grain orientation) was used to assess the likelihood of slip transfer across boundaries. It was found that transfer across grain boundaries was rare in near-cube oriented grains, and convincing evidence was only found when m' > 0.97, which corresponds to low-angle boundaries with <15° misorientation. This behavior was explained by the presence of many active slip slips in near-cube oriented grains that favor self-accommodation of the grain shape to the evolving boundary conditions imposed by neighboring grains instead of promoting slip transfer across the boundary. These results indicate that the alignment between slip planes and slip directions across the boundary is not the only important metric to determine the threshold for slip transfer, as the particular details of deformation in each grain (such as the number of available slip systems) also must be considered.
△ Less
Submitted 12 February, 2019;
originally announced February 2019.
-
Does a dissolution-precipitation mechanism explain concrete creep in moist environments?
Authors:
Isabella Pignatelli,
Aditya Kumar,
Rouhollah Alizadeh,
Yann Le Pape,
Mathieu Bauchy,
Gaurav Sant
Abstract:
Long-term creep (i.e., deformation under sustained load) is a significant material response that needs to be accounted for in concrete structural design. However, the nature and origin of creep remains poorly understood, and controversial. Here, we propose that concrete creep at RH (relative humidity) > 50%, but fixed moisture-contents (i.e., basic creep), arises from a dissolution-precipitation m…
▽ More
Long-term creep (i.e., deformation under sustained load) is a significant material response that needs to be accounted for in concrete structural design. However, the nature and origin of creep remains poorly understood, and controversial. Here, we propose that concrete creep at RH (relative humidity) > 50%, but fixed moisture-contents (i.e., basic creep), arises from a dissolution-precipitation mechanism, active at nanoscale grain contacts, as is often observed in a geological context, e.g., when rocks are exposed to sustained loads, in moist environments. Based on micro-indentation and vertical scanning interferometry experiments, and molecular dynamics simulations carried out on calcium-silicate-hydrates (C-S-H's), the major binding phase in concrete, of different compositions, we show that creep rates are well correlated to dissolution rates - an observation which supports the dissolution-precipitation mechanism as the origin of concrete creep. C-S-H compositions featuring high resistance to dissolution, and hence creep are identified - analysis of which, using topological constraint theory, indicates that these compositions present limited relaxation modes on account of their optimally connected (i.e., constrained) atomic networks.
△ Less
Submitted 27 August, 2015;
originally announced August 2015.
-
Spectral radius, numerical radius, and the product of operators
Authors:
Rahim Alizadeh,
Mohammad B. Asadi,
Che-Man Cheng,
Wanli Hong,
Chi-Kwong Li
Abstract:
Let $σ(A)$, $ρ(A)$ and $r(A)$ denote the spectrum, spectral radius and numerical radius of a bounded linear operator $A$ on a Hilbert space $H$, respectively. We show that a linear operator $A$ satisfying $$ρ(AB)\le r(A)r(B) \quad\text{ for all bounded linear operators } B$$ if and only if there is a unique $μ\in σ(A)$ satisfying $|μ| = ρ(A)$ and $A = \frac{μ(I + L)}{2}$ for a contraction $L$ with…
▽ More
Let $σ(A)$, $ρ(A)$ and $r(A)$ denote the spectrum, spectral radius and numerical radius of a bounded linear operator $A$ on a Hilbert space $H$, respectively. We show that a linear operator $A$ satisfying $$ρ(AB)\le r(A)r(B) \quad\text{ for all bounded linear operators } B$$ if and only if there is a unique $μ\in σ(A)$ satisfying $|μ| = ρ(A)$ and $A = \frac{μ(I + L)}{2}$ for a contraction $L$ with $1\inσ(L)$. One can get the same conclusion on $A$ if $ρ(AB) \le r(A)r(B)$ for all rank one operators $B$. If $H$ is of finite dimension, we can further decompose $L$ as a direct sum of $C \oplus 0$ under a suitable choice of orthonormal basis so that $Re(C^{-1}x,x) \ge 1$ for all unit vector $x$.
△ Less
Submitted 26 August, 2014; v1 submitted 18 July, 2014;
originally announced July 2014.
-
Negative refraction of a three-dimensional metallic photonic crystal
Authors:
Ali Mahmoudi,
Abbas Semnani,
Ramazan Alizadeh,
Roohollah Adeli
Abstract:
A metamaterial with a negative effective index of refraction is made from a three-dimensional hexagonal lattice photonic crystal with a metallic basis embedded in foam. It has been simulated with Ansoft HFSSTM in a frequency range from 7.0 to 12.0 GHz. Simulated results tested experimentally and negative refraction verified in some frequencies. Experimental results are in excellent agreement wit…
▽ More
A metamaterial with a negative effective index of refraction is made from a three-dimensional hexagonal lattice photonic crystal with a metallic basis embedded in foam. It has been simulated with Ansoft HFSSTM in a frequency range from 7.0 to 12.0 GHz. Simulated results tested experimentally and negative refraction verified in some frequencies. Experimental results are in excellent agreement with simulations.
△ Less
Submitted 9 May, 2007; v1 submitted 23 January, 2007;
originally announced January 2007.
