-
A New Architecture for Energy Efficient Fault Detection Using Energy Harvesters
Authors:
Dongti Zhang,
Patricio Peralta-Braz,
Chun Tung Chou,
Elena Atroshchenko,
Mehrisadat Makki Alamdari,
Mahbub Hassan
Abstract:
The current battery-powered fault detection system for vibration monitoring has a rather limited lifetime. This is because the high-frequency sampling (typically tens of kilo-Hertz) required for vibration monitoring results in high energy consumption in both the analog-to-digital (ADC) converter and wireless transmissions. This paper proposes a new fault detection architecture that can significant…
▽ More
The current battery-powered fault detection system for vibration monitoring has a rather limited lifetime. This is because the high-frequency sampling (typically tens of kilo-Hertz) required for vibration monitoring results in high energy consumption in both the analog-to-digital (ADC) converter and wireless transmissions. This paper proposes a new fault detection architecture that can significantly reduce the energy consumption of the ADC and wireless transmission. Our inspiration for the new architecture is based on the observation that the many tens of thousand of data samples collected for fault detection are ultimately transformed into a small number of features. If we can generate these features directly without high frequency sampling, then we can avoid the the energy cost for ADC and wireless transmissions. We propose to use piezoelectric energy harvesters (which can be designed to have different frequency responses) and integrators to obtain these features in an energy-efficient manner. By using a publicly available data set for ball bearing fault detection (which was originally sampled at 51.2kHz) and piezoelectric energy harvester models, we can produce features, which when sampled at 0.33Hz, give a fault detection accuracy of 89% while reducing the sampling requirement by 4 orders-of-magnitude.
△ Less
Submitted 21 February, 2024;
originally announced February 2024.
-
Optimal design of Piezoelectric Energy Harvesters for bridge infrastructure: Effects of Location and Traffic Intensity on Energy Production
Authors:
Shaui Yao,
Patricio Peralta-Braz,
Mehri Makki Alamdari,
Rafael O. Ruiz,
Elena Atroshchenko,
Mahbub Hassan
Abstract:
Piezoelectric energy harvesters (PEHs) can be used as an additional power supply for a Structural Health Monitoring (SHM) system. Its design can be optimised for the best performance; however, the optimal design depends on the input vibration, e.g. acceleration of a bridge due to wind loads and passing traffic. In previous studies, we have shown that optimal design tunes to some predominant freque…
▽ More
Piezoelectric energy harvesters (PEHs) can be used as an additional power supply for a Structural Health Monitoring (SHM) system. Its design can be optimised for the best performance; however, the optimal design depends on the input vibration, e.g. acceleration of a bridge due to wind loads and passing traffic. In previous studies, we have shown that optimal design tunes to some predominant frequency of the signal spectrum. However, our previous study was limited to a single location of a PEH on a bridge. In this work, we extend the rigorous optimisation framework to include the effect of the PEH's location. The optimisation framework uses the PEH plate model discretised by IsoGeometric Analysis (IGA) and coupled with the Particle Swarm Optimisation algorithm to find the designs with maximum energy outputs for many acceleration histories, extracted from the recorded dynamic response data of a real cable-stayed bridge in Australia. Then, clustering is performed to find several best candidates for the entire bridge. An additional study is performed to quantify the effect of traffic intensity on the produced energy. It is shown that variation in traffic volume throughout the 24hr time window leads to variation in optimal PEH designs. The study concludes the impact of location and traffic on energy harvesting by identifying the optimal PEH design and placement throughout the bridge structure. The results indicate that the key factors of maximising energy harvesting efficiency are related to the input excitation and the mode of vibration being excited. The position of maximum displacement in the vibration mode corresponds to the best location for energy harvesting. Also, the change in traffic intensity affects the amount of convertible mechanical energy and also directs the fundamental frequency of a PEH to shift within a specific range of frequencies to achieve the highest energy conversion.
△ Less
Submitted 6 March, 2023;
originally announced March 2023.
-
On the Joint Optimization of Energy Harvesting and Sensing of Piezoelectric Energy Harvesters: Case Study of a Cable-Stayed Bridge
Authors:
Patricio Peralta-Braz,
Mehrisadat Makki Alamdari,
Rafael O. Ruiz,
Elena Atroshchenko,
Mahbub Hassan
Abstract:
Piezoelectric Energy Harvesters (PEHs) are typically employed to provide additional source of energy for a sensing system. However, studies show that a PEH can be also used as a sensor to acquire information about the source of vibration by analysing the produced voltage signal. This opens a possibility to create Simultaneous Energy Harvesting and Sensing (SEHS) system, where a single piece of har…
▽ More
Piezoelectric Energy Harvesters (PEHs) are typically employed to provide additional source of energy for a sensing system. However, studies show that a PEH can be also used as a sensor to acquire information about the source of vibration by analysing the produced voltage signal. This opens a possibility to create Simultaneous Energy Harvesting and Sensing (SEHS) system, where a single piece of hardware, a PEH, acts as both, a harvester and as a sensor. This raises a question if it is possible to design a bi-functional PEH device with optimal harvesting and sensing performance. In this work, we propose a bi-objective PEH design optimisation framework and show that there is a trade-off between energy harvesting efficiency and sensing accuracy within a PEH design space. The proposed framework is based on an extensive vibration (strain and acceleration) dataset collected from a real-world operational cable-stayed bridge in New South Wales, Australia. The bridge acceleration data is used as an input for a PEH numerical model to simulate a voltage signal and estimate the amount of produced energy. The numerical PEH model is based on the Kirchhoff-Love plate and isogeometric analysis. For sensing, convolutional neural network AlexNet is trained to identify traffic speed labels from voltage CWT (Continuous Wavelet Transform) images. In order to improve computational efficiency of the approach, a kriging metamodel is built and genetic algorithm is used as an optimisation method. The results are presented in the form of Pareto fronts in three design spaces.
△ Less
Submitted 15 December, 2022; v1 submitted 14 May, 2022;
originally announced May 2022.
-
Design optimisation of piezoelectric energy harvesters for bridge infrastructure
Authors:
Patricio Peralta-Braz,
Mehrisadat Makki Alamdari,
Rafael O. Ruiz,
Elena Atroshchenko,
Mahbub Hassan
Abstract:
Vibrational energy harvested from the bridge excitation due to the traffic flow or the wind load can be supplied to sensors in a Structural Health Monitoring (SHM) system and help prolong its service life, reduce chemical battery waste and enable its use in remote locations. A common approach to designing a Piezoelectric Energy Harvester (PEH) consists in tuning its fundamental frequency to some t…
▽ More
Vibrational energy harvested from the bridge excitation due to the traffic flow or the wind load can be supplied to sensors in a Structural Health Monitoring (SHM) system and help prolong its service life, reduce chemical battery waste and enable its use in remote locations. A common approach to designing a Piezoelectric Energy Harvester (PEH) consists in tuning its fundamental frequency to some target value (e.g., the fundamental frequency of a bridge). However, such approach does not answer the question if the chosen target frequency is optimal, and does not take into account the possibility to have multiple design configurations with the same fundamental frequency. In this work, we approach the problem of a PEH design optimisation in a rigorous way, using a PEH model based on the Kirchhoff-Love plate theory and Isogeometric Analysis (IGA), coupled with the Modal Order Reduction (MOR) approach and Runge-Kutta time integration method. The model is further equipped with the Particle Swarm Optimisation (PSO) algorithm that allows finding geometry which maximises energy output from a given base acceleration signal. A comprehensive study is conducted to infer the impact of a PEH geometry on its energy harvesting performance in a real-world setting by considering field health monitoring data of a large-scale cable-stayed bridge in NSW, Australia. A shape optimisation framework is developed based on acceleration events, i.e., where the level of response exceeds a certain threshold. Designs obtained in the event-based optimisation are then clustered to propose several best candidates for continuous energy generation. This work represents the first study on PEH design optimisation for real operational conditions.
△ Less
Submitted 26 September, 2022; v1 submitted 13 May, 2022;
originally announced May 2022.
-
On Physical Realizability for Inverse Structural Designs: Bounding the Least Eigenvalue of an Unknown Mass Matrix
Authors:
P. Cheema,
M. M. Alamdari,
G. A. Vio
Abstract:
In the field of structural engineering analysis, a common requirement is to calculate the modal frequencies of a structure that has undergone an update, either naturally (such as from material degradation), or due to man-made influences (by placing point masses along a structure). In addition to this requirement, it is common to only have access to truncated modal testing results. In this paper, w…
▽ More
In the field of structural engineering analysis, a common requirement is to calculate the modal frequencies of a structure that has undergone an update, either naturally (such as from material degradation), or due to man-made influences (by placing point masses along a structure). In addition to this requirement, it is common to only have access to truncated modal testing results. In this paper, we derive analytical bounds for the first eigenvalue of a completely unobserved mass matrix for linear elastic systems. Doing so allows engineers to proceed with modifying linear elastic systems, without requiring direct access to the mass matrix. This is because it is often difficult to know exactly what negative mass perturbations are allowable, given that the full mass matrix is an unknown quantity. Ultimately, the analysis in this paper will proceed by assuming only access to the left and right eigenvectors of the underlying system - which are both possible to obtain via physical experiments, so that the bounds are not only physically realizable, but also practically realizable.
△ Less
Submitted 23 August, 2020; v1 submitted 29 June, 2020;
originally announced June 2020.
-
New Approaches to Inverse Structural Modification Theory using Random Projections
Authors:
Prasad Cheema,
Mehrisadat M. Alamdari,
Gareth A. Vio
Abstract:
In many contexts the modal properties of a structure change, either due to the impact of a changing environment, fatigue, or due to the presence of structural damage. For example during flight, an aircraft's modal properties are known to change with both altitude and velocity. It is thus important to quantify these changes given only a truncated set of modal data, which is usually the case experim…
▽ More
In many contexts the modal properties of a structure change, either due to the impact of a changing environment, fatigue, or due to the presence of structural damage. For example during flight, an aircraft's modal properties are known to change with both altitude and velocity. It is thus important to quantify these changes given only a truncated set of modal data, which is usually the case experimentally. This procedure is formally known as the generalised inverse eigenvalue problem. In this paper we experimentally show that first-order gradient-based methods that optimise objective functions defined over a modal are prohibitive due to the required small step sizes. This in turn leads to the justification of using a non-gradient, black box optimiser in the form of particle swarm optimisation. We further show how it is possible to solve such inverse eigenvalue problems in a lower dimensional space by the use of random projections, which in many cases reduces the total dimensionality of the optimisation problem by 80% to 99%. Two example problems are explored involving a ten-dimensional mass-stiffness toy problem, and a one-dimensional finite element mass-stiffness approximation for a Boeing 737-300 aircraft.
△ Less
Submitted 10 December, 2018;
originally announced December 2018.
