Showing 1–5 of 5 results for author: Adapa, S R

Heat Transfer Coefficients of Moving Particle Beds from Flow-Dependent Particle Bed Thermal Conductivity and Near-Wall Resistance

Authors: Sarath R. Adapa, Xintong Zhang, Tianshi Feng, Ka Man Chung, Kevin J. Albrecht, Clifford K. Ho, Dimitri A. Madden, Renkun Chen

Abstract: Determination of heat transfer coefficients for flowing packed particle beds is essential to the design of particle heat exchangers, and other thermal processes. While such dense granular flows fall into the well-known plug-flow regime, the discrete nature of granular materials alters the thermal transport processes in both the near-wall and bulk regions of flowing particle beds from their station… ▽ More Determination of heat transfer coefficients for flowing packed particle beds is essential to the design of particle heat exchangers, and other thermal processes. While such dense granular flows fall into the well-known plug-flow regime, the discrete nature of granular materials alters the thermal transport processes in both the near-wall and bulk regions of flowing particle beds from their stationary counterparts. As a result, heat transfer correlations based on the stationary particle bed thermal conductivity could be inadequate for flowing particles in a heat exchanger. Earlier works have achieved reasonable agreement with experiments by treating granular media as a plug-flow continuum with a near-wall thermal resistance in series. However, the properties of the continuum were often obtained from measurements on stationary beds owing to the difficulty of flowing bed measurements. In this work, it was found that the properties of a stationary bed are highly sensitive to the method of particle packing and there is a decrease in the particle bed thermal conductivity and increase in the near-wall thermal resistance, measured as an effective air gap thickness, on the onset of particle flow. These variations in the thermophysical properties of stationary and flowing particle beds can lead to errors in heat transfer coefficient calculations. Therefore, the heat transfer coefficients for granular flows were calculated using experimentally determined flowing particle bed thermal conductivity and near-wall air gap for ceramic particles -CARBOCP40/100(275 um), HSP40/70(404um) and HSP16/30(956um); at velocities of 5-15mms-1; and temperatures of 300-650C. The thermal conductivity and air gap values for CP40/100 and HSP40/70 were further used to calculate heat transfer coefficients across different particle bed temperatures and velocities for different parallel-plate heat exchanger dimensions. △ Less

Submitted 27 May, 2024; v1 submitted 28 March, 2024; originally announced March 2024.

Thermal Conductivity Measurement Using Modulated Photothermal Radiometry for Nitrate and Chloride Molten Salts

Authors: Ka Man Chung, Tianshi Feng, Jian Zeng, Sarath Reddy Adapa, Xintong Zhang, Andrew Z. Zhao, Ye Zhang, Peiwen Li, Youyang Zhao, Javier E. Garay, Renkun Chen

Abstract: Molten salts are being used or explored for thermal energy storage and conversion systems in concentrating solar power and nuclear power plants. Thermal conductivity of molten salts is an important thermophysical property dictating the performance and cost of these systems, but its accurate measurement has been challenging, as evidenced by wide scattering of existing data in literature. The corros… ▽ More Molten salts are being used or explored for thermal energy storage and conversion systems in concentrating solar power and nuclear power plants. Thermal conductivity of molten salts is an important thermophysical property dictating the performance and cost of these systems, but its accurate measurement has been challenging, as evidenced by wide scattering of existing data in literature. The corrosive and conducting nature of these fluids also leads to time consuming sample preparation processes of many contact-based measurements. Here, we report the measurement of thermal conductivity of molten salts using a modulated photothermal radiometry (MPR) technique, which is a laser-based, non-contact, frequency-domain method adopted for molten salts for the first time. By unitizing the advantages of front side sensing of frequency-domain measurements and the vertical holder orientation, the technique can minimize the natural convection and salt cree** effects, thus yielding accurate molten salt thermal conductivity. The MPR technique is first calibrated using standard molten materials including paraffin wax and sulfur. It is then applied on measuring pure nitrate salts ($NaNO_3$ and $KNO_3$), solar salt ($NaNO_3-KNO_3$ mixture), and chloride salt ($NaCl-KCl-MgCl_2$). The measurement results are compared with data from literature, especially those obtained from laser flash analysis (LFA). Our results demonstrate that the MPR is a convenient and reliable technique of measuring thermal conductivity of molten salts. Accurate thermal conductivity data of molten salts will be valuable in develo** the next-generation high-temperature thermal energy storage and conversion systems. △ Less

Submitted 31 August, 2023; originally announced September 2023.

In-situ Thermophysical Measurement of Flowing Molten Chloride Salt Using Modulated Photothermal Radiometry

Authors: Ka Man Chung, Ye Zhang, Jian Zeng, Fouad Haddad, Sarath Reddy Adapa, Tianshi Feng, Peiwen Li, Renkun Chen

Abstract: Molten salts are a leading candidate for high-temperature heat transfer fluids (HTFs) for thermal energy storage and conversion systems in concentrated solar power (CSP) and nuclear energy power plants. The ability to probe molten salt thermal transport properties in both stationary and flowing status is important for the evaluation of their heat transfer performance under realistic operational co… ▽ More Molten salts are a leading candidate for high-temperature heat transfer fluids (HTFs) for thermal energy storage and conversion systems in concentrated solar power (CSP) and nuclear energy power plants. The ability to probe molten salt thermal transport properties in both stationary and flowing status is important for the evaluation of their heat transfer performance under realistic operational conditions, including the temperature range and potential degradation due to corrosion and contamination. However, accurate thermal transport properties are usually challenging to obtain even for stagnant molten salts due to different sources of errors from convection, radiation, and corrosion, let alone flowing ones. To the best of authors' knowledge, there is no available in-situ technique for measuring flowing molten salt thermal conductivity. Here, we report the first in-situ flowing molten salt thermal conductivity measurement using modulated photothermal radiometry (MPR). We could successfully perform the first in-situ thermal conductivity measurement of flowing molten $NaCl-KCl-MgCl_2$ in the typical operating temperature (520 and 580 $^oC$) with flow velocities ranging from around 0.3 to 1.0 $m$$s^-1$. The relative change of the molten salt thermal conductivity was measured. Gnielinski's correlation was also used to estimate the heat transfer coefficient h of the flowing $NaCl-KCl-MgCl_2$ in the given experimental condition. The work showed the potential of the MPR technique serving as an in-situ diagnostics tool to evaluate the heat transfer performance of flowing molten salts and other high-temperature HTFs. △ Less

Submitted 31 August, 2023; originally announced September 2023.

Measurement and Analysis of Thermal Conductivity of Ceramic Particle Beds for Solar Thermal Energy Storage

Authors: Ka Man Chung, Jian Zeng, Sarath Reddy Adapa, Tianshi Feng, Malavika V. Bagepalli, Peter G. Loutzenhiser, Kevin J. Albrecht, Clifford K. Ho, Renkun Chen

Abstract: A systematic study was performed to measure the effective thermal conductivity of ceramic particle beds, a promising heat transfer and thermal energy storage media for concentrating solar power (CSP). The thermal conductivity of the ceramic particle beds was measured using a transient hot-wire (THW) method within a temperature range of room temperature to 700 oC, the target operating temperature o… ▽ More A systematic study was performed to measure the effective thermal conductivity of ceramic particle beds, a promising heat transfer and thermal energy storage media for concentrating solar power (CSP). The thermal conductivity of the ceramic particle beds was measured using a transient hot-wire (THW) method within a temperature range of room temperature to 700 oC, the target operating temperature of the next-generation CSP systems. Two different types of ceramic particles were examined: (1) CARBOBEAD HSP 40/70 and (2) CARBOBEAD CP 40/100 with the average particle sizes of ~ 400 μm and ~280 μm, respectively, and thermal conductivities ranging from ~0.25 W m-1 K-1 to ~0.50 W m-1 K-1 from 20 oC to 700 oC in both air and N2 gas. The gaseous pressure dependence of the thermal conductivity of the ceramic particle beds was also studied in the N2 environment to differentiate the contributions from gas conduction, solid conduction, and radiation. Calculations using the Zehner, Bauer, and Schlünder (ZBS) model showed good agreements with the measurements. Based on the model, it is concluded that the effective thermal conductivity of the packed particle beds is dominated by the gas conduction while the solid conduction and radiation contributes to about 20% of the effective thermal conductivity at high temperature. △ Less

Submitted 5 May, 2021; originally announced May 2021.

Comments: Department of Mechanical and Aerospace Engineering, University of California, San Diego, La Jolla, California 92093, USA Georgia Institute of Technology, Atlanta, Georgia 30332-0405, USA Sandia National Laboratories, 1515 Eubank Blvd. SE, Albuquerque, NM 87123, USA #Corresponding author: [email protected]

In-situ Thermal Transport Measurement of Flowing Fluid using Modulated Photothermal Radiometry

Authors: Jian Zeng, Ka Man Chung, Sarath Reddy Adapa, Tianshi Feng, Renkun Chen

Abstract: In situ thermal transport measurement of flowing fluid could be useful for the characterization and diagnosis of practical thermal systems such as fluid heat exchangers and thermal energy storage systems. Despite abundant reports on the ex-situ thermal conductivity measurement of stagnant fluids, a suitable technique for the thermal conductivity measurement of flowing fluid has been rarely reporte… ▽ More In situ thermal transport measurement of flowing fluid could be useful for the characterization and diagnosis of practical thermal systems such as fluid heat exchangers and thermal energy storage systems. Despite abundant reports on the ex-situ thermal conductivity measurement of stagnant fluids, a suitable technique for the thermal conductivity measurement of flowing fluid has been rarely reported. This paper presents the thermal conductivity measurement of flowing fluid within a pipe using a non-contact modulated photothermal radiometry (MPR) technique, where the surface of the pipe is heated by an intensity-modulated laser and the heat diffuses into the fluid with suitable modulation frequency. We design a tube section with small wall thickness suitable for the MPR measurements to maximize the sensitivity of the thermal response to the fluid properties while minimizing the lateral heat spreading effect. Intrinsic thermal conductivity of different fluids was obtained within a proper range of frequency and flow velocity where the forced convection effect is negligible. The forced convection effect became prominent at high flowing velocity and at low modulation frequency, leading to overestimated thermal conductivity of fluid. It is found that the intrinsic thermal conductivity could be obtained when the flow velocity is less than 100 mm/sec and ReD1/2Pr1/3 < 100 for DI water and Xceltherm oil under the specified experimental conditions, where Re_D is the Reynolds number and Pr is the Prandtl number. △ Less

Submitted 30 April, 2021; originally announced May 2021.

Comments: 1Department of Mechanical and Aerospace Engineering, University of California, San Diego, La Jolla, California 92093, United States 2Program of Material Science and Engineering, University of California, San Diego, La Jolla, California 92093, United States *These authors contributed equally. #Corresponding author: [email protected]