Showing 1–45 of 45 results for author: Abraham, D

Inactive Overhang in Silicon Anodes

Authors: Aidin I. OBrien, Stephen E. Trask, Devashish Salpekar, Seoung-Bum Son, Alison R. Dunlop, Gabriel M. Veith, Wenquan Lu, Brian J. Ingram, Daniel P. Abraham, Andrew N. Jansen, Marco-Tulio F. Rodrigues

Abstract: Li-ion batteries contain excess anode area to improve manufacturability and prevent Li plating. These overhang areas in graphite electrodes are active but experience decreased Li+ flux during cycling. Over time, the overhang and the anode portions directly opposite to the cathode can exchange Li+, driven by differences in local electrical potential across the electrode, which artificially inflates… ▽ More Li-ion batteries contain excess anode area to improve manufacturability and prevent Li plating. These overhang areas in graphite electrodes are active but experience decreased Li+ flux during cycling. Over time, the overhang and the anode portions directly opposite to the cathode can exchange Li+, driven by differences in local electrical potential across the electrode, which artificially inflates or decreases the measured cell capacity. Here, we show that lithiation of the overhang is less likely to happen in silicon anodes paired with layered oxide cathodes. The large voltage hysteresis of silicon creates a lower driving force for Li+ exchange as lithium ions transit into the overhang, rendering this exchange highly inefficient. For crystalline Si particles, Li+ storage at the overhang is prohibitive, because the low potential required for the initial lithiation can act as thermodynamic barrier for this exchange. We use micro-Raman spectroscopy to demonstrate that crystalline Si particles at the overhang are never lithiated even after cell storage at 45 oC for four months. Since the anode overhang can affect the forecasting of cell life, cells using silicon anodes may require different methodologies for life estimation compared to those used for traditional graphite-based Li-ion batteries. △ Less

Submitted 15 May, 2024; originally announced May 2024.

Low-loss liquid metal interconnects for superconducting quantum circuits

Authors: Zhancheng Yao, Martin Sandberg, David W. Abraham, David J. Bishop

Abstract: Building a modular architecture with superconducting quantum computing chips is one of the means to achieve qubit scalability, allowing the screening, selection, replacement, and integration of individual qubit modules into large quantum systems. However, the nondestructive replacement of modules within a compact architecture remains a challenge. Liquid metals, specifically gallium alloys, can be… ▽ More Building a modular architecture with superconducting quantum computing chips is one of the means to achieve qubit scalability, allowing the screening, selection, replacement, and integration of individual qubit modules into large quantum systems. However, the nondestructive replacement of modules within a compact architecture remains a challenge. Liquid metals, specifically gallium alloys, can be alternatives to solid-state galvanic interconnects. This is motivated by their self-healing, self-aligning, and other desirable fluidic properties, potentially enabling the nondestructive replacement of modules at room temperatures, even after operating the entire system at millikelvin regimes. In this study, we present coplanar waveguide resonators (CPWRs) interconnected by gallium alloy droplets, achieving high internal quality factors up to nearly one million and demonstrating performance on par with the continuous solid-state CPWRs. Leveraging the desirable fluidic properties of gallium alloys at room temperature and their compact design, we envision a modular quantum system enabled by liquid metals. △ Less

Submitted 27 June, 2024; v1 submitted 31 March, 2024; originally announced April 2024.

Journal ref: Appl. Phys. Lett. 124, 264002 (2024)

Surface fields and emergence of long-range couplings in classical uniaxial ferromagnetic arrays

Authors: D. B. Abraham, A. Maciolek, A. Squarcini

Abstract: Critical wetting is of crucial importance for the phase behaviour of a simple fluid or Ising magnet confined between walls that exert opposing surface fields so that one wall favours liquid (spin up), while the other favours gas (spin down). We show that arrays of boxes filled with fluid or Ising magnet and linked by channels with such ``opposing'' walls can exhibit long-range cooperative effects,… ▽ More Critical wetting is of crucial importance for the phase behaviour of a simple fluid or Ising magnet confined between walls that exert opposing surface fields so that one wall favours liquid (spin up), while the other favours gas (spin down). We show that arrays of boxes filled with fluid or Ising magnet and linked by channels with such ``opposing'' walls can exhibit long-range cooperative effects, on a length scale far exceeding the bulk correlation length. We give the theoretical foundations of these long-range couplings by using a lattice gas (Ising model) description of a system. △ Less

Submitted 29 December, 2023; originally announced December 2023.

Comments: 16 pages, 14 figures

Sequence adaptive field-imperfection estimation (SAFE): retrospective estimation and correction of $B_1^+$ and $B_0$ inhomogeneities for enhanced MRF quantification

Authors: Mengze Gao, Xiaozhi Cao, Daniel Abraham, Zihan Zhou, Kawin Setsompop

Abstract: $B_1^+$ and $B_0$ field-inhomogeneities can significantly reduce accuracy and robustness of MRF's quantitative parameter estimates. Additional $B_1^+$ and $B_0$ calibration scans can mitigate this but add scan time and cannot be applied retrospectively to previously collected data. Here, we proposed a calibration-free sequence-adaptive deep-learning framework, to estimate and correct for $B_1^+… ▽ More $B_1^+$ and $B_0$ field-inhomogeneities can significantly reduce accuracy and robustness of MRF's quantitative parameter estimates. Additional $B_1^+$ and $B_0$ calibration scans can mitigate this but add scan time and cannot be applied retrospectively to previously collected data. Here, we proposed a calibration-free sequence-adaptive deep-learning framework, to estimate and correct for $B_1^+$ and $B_0$ effects of any MRF sequence. We demonstrate its capability on arbitrary MRF sequences at 3T, where no training data were previously obtained. Such approach can be applied to any previously-acquired and future MRF-scans. The flexibility in directly applying this framework to other quantitative sequences is also highlighted. △ Less

Submitted 14 December, 2023; originally announced December 2023.

Comments: 12 pages, 5 figures, submitted to International Society for Magnetic Resonance in Medicine 31th Scientific Meeting, 2024

Implicit Representation of GRAPPA Kernels for Fast MRI Reconstruction

Authors: Daniel Abraham, Mark Nishimura, Xiaozhi Cao, Congyu Liao, Kawin Setsompop

Abstract: MRI data is acquired in Fourier space/k-space. Data acquisition is typically performed on a Cartesian grid in this space to enable the use of a fast Fourier transform algorithm to achieve fast and efficient reconstruction. However, it has been shown that for multiple applications, non-Cartesian data acquisition can improve the performance of MR imaging by providing fast and more efficient data acq… ▽ More MRI data is acquired in Fourier space/k-space. Data acquisition is typically performed on a Cartesian grid in this space to enable the use of a fast Fourier transform algorithm to achieve fast and efficient reconstruction. However, it has been shown that for multiple applications, non-Cartesian data acquisition can improve the performance of MR imaging by providing fast and more efficient data acquisition, and improving motion robustness. Nonetheless, the image reconstruction process of non-Cartesian data is more involved and can be time-consuming, even through the use of efficient algorithms such as non-uniform FFT (NUFFT). Reconstruction complexity is further exacerbated when imaging in the presence of field imperfections. This work (implicit GROG) provides an efficient approach to transform the field corrupted non-Cartesian data into clean Cartesian data, to achieve simpler and faster reconstruction which should help enable non-Cartesian data sampling to be performed more widely in MRI. △ Less

Submitted 14 January, 2024; v1 submitted 16 October, 2023; originally announced October 2023.

DotHash: Estimating Set Similarity Metrics for Link Prediction and Document Deduplication

Authors: Igor Nunes, Mike Heddes, Pere Vergés, Danny Abraham, Alexander Veidenbaum, Alexandru Nicolau, Tony Givargis

Abstract: Metrics for set similarity are a core aspect of several data mining tasks. To remove duplicate results in a Web search, for example, a common approach looks at the Jaccard index between all pairs of pages. In social network analysis, a much-celebrated metric is the Adamic-Adar index, widely used to compare node neighborhood sets in the important problem of predicting links. However, with the incre… ▽ More Metrics for set similarity are a core aspect of several data mining tasks. To remove duplicate results in a Web search, for example, a common approach looks at the Jaccard index between all pairs of pages. In social network analysis, a much-celebrated metric is the Adamic-Adar index, widely used to compare node neighborhood sets in the important problem of predicting links. However, with the increasing amount of data to be processed, calculating the exact similarity between all pairs can be intractable. The challenge of working at this scale has motivated research into efficient estimators for set similarity metrics. The two most popular estimators, MinHash and SimHash, are indeed used in applications such as document deduplication and recommender systems where large volumes of data need to be processed. Given the importance of these tasks, the demand for advancing estimators is evident. We propose DotHash, an unbiased estimator for the intersection size of two sets. DotHash can be used to estimate the Jaccard index and, to the best of our knowledge, is the first method that can also estimate the Adamic-Adar index and a family of related metrics. We formally define this family of metrics, provide theoretical bounds on the probability of estimate errors, and analyze its empirical performance. Our experimental results indicate that DotHash is more accurate than the other estimators in link prediction and detecting duplicate documents with the same complexity and similar comparison time. △ Less

Submitted 26 May, 2023; originally announced May 2023.

Pouch cells with 15% silicon calendar-aged for 4 years

Authors: Marco-Tulio F. Rodrigues, Zhenzhen Yang, Stephen E. Trask, Alison R. Dunlop, Minkyu Kim, Fulya Dogan, Baris Key, Ira Bloom, Daniel P. Abraham, Andrew N. Jansen

Abstract: Small amounts of high-capacity silicon-based materials are already used in the anode of commercial Li-ion batteries, hel** increase their energy density. Despite their remarkable storage capability, silicon continuously reacts with the electrolyte, accelerating time-dependent cell performance fade. Nevertheless, very limited information is available on the specific consequences of this reactivit… ▽ More Small amounts of high-capacity silicon-based materials are already used in the anode of commercial Li-ion batteries, hel** increase their energy density. Despite their remarkable storage capability, silicon continuously reacts with the electrolyte, accelerating time-dependent cell performance fade. Nevertheless, very limited information is available on the specific consequences of this reactivity for the calendar aging of Li-ion cells. Here, we analyze aging effects on 450 mAh pouch cells containing 15 wt% of Si (and 73 wt% graphite) after storage at 21 oC for four years. We show that severe losses of Si capacity occurred due to particle isolation when cells were stored at high states of charge (SOC), but not when cells were fully discharged prior to storage. Impedance rise was also significantly higher when cells were kept at high SOCs and was mostly due to phenomena taking place at the cathode; the continuous electrolyte reduction at the anode did not lead to a major increase in bulk electrode resistance. A series of post-test characterization provided additional information on the effects of time and SOC on the calendar aging of Si-containing cells. Our study highlights the many challenges posed by Si during calendar aging and can inform future studies in the field. △ Less

Submitted 31 August, 2022; originally announced September 2022.

Journal ref: J. Power Sources 565, 232894 (2023)

CEBaB: Estimating the Causal Effects of Real-World Concepts on NLP Model Behavior

Authors: Eldar David Abraham, Karel D'Oosterlinck, Amir Feder, Yair Ori Gat, Atticus Geiger, Christopher Potts, Roi Reichart, Zhengxuan Wu

Abstract: The increasing size and complexity of modern ML systems has improved their predictive capabilities but made their behavior harder to explain. Many techniques for model explanation have been developed in response, but we lack clear criteria for assessing these techniques. In this paper, we cast model explanation as the causal inference problem of estimating causal effects of real-world concepts on… ▽ More The increasing size and complexity of modern ML systems has improved their predictive capabilities but made their behavior harder to explain. Many techniques for model explanation have been developed in response, but we lack clear criteria for assessing these techniques. In this paper, we cast model explanation as the causal inference problem of estimating causal effects of real-world concepts on the output behavior of ML models given actual input data. We introduce CEBaB, a new benchmark dataset for assessing concept-based explanation methods in Natural Language Processing (NLP). CEBaB consists of short restaurant reviews with human-generated counterfactual reviews in which an aspect (food, noise, ambiance, service) of the dining experience was modified. Original and counterfactual reviews are annotated with multiply-validated sentiment ratings at the aspect-level and review-level. The rich structure of CEBaB allows us to go beyond input features to study the effects of abstract, real-world concepts on model behavior. We use CEBaB to compare the quality of a range of concept-based explanation methods covering different assumptions and conceptions of the problem, and we seek to establish natural metrics for comparative assessments of these methods. △ Less

Submitted 12 October, 2022; v1 submitted 27 May, 2022; originally announced May 2022.

Comments: Accepted to NeurIPS 2022

Torchhd: An Open Source Python Library to Support Research on Hyperdimensional Computing and Vector Symbolic Architectures

Authors: Mike Heddes, Igor Nunes, Pere Vergés, Denis Kleyko, Danny Abraham, Tony Givargis, Alexandru Nicolau, Alexander Veidenbaum

Abstract: Hyperdimensional computing (HD), also known as vector symbolic architectures (VSA), is a framework for computing with distributed representations by exploiting properties of random high-dimensional vector spaces. The commitment of the scientific community to aggregate and disseminate research in this particularly multidisciplinary area has been fundamental for its advancement. Joining these effort… ▽ More Hyperdimensional computing (HD), also known as vector symbolic architectures (VSA), is a framework for computing with distributed representations by exploiting properties of random high-dimensional vector spaces. The commitment of the scientific community to aggregate and disseminate research in this particularly multidisciplinary area has been fundamental for its advancement. Joining these efforts, we present Torchhd, a high-performance open source Python library for HD/VSA. Torchhd seeks to make HD/VSA more accessible and serves as an efficient foundation for further research and application development. The easy-to-use library builds on top of PyTorch and features state-of-the-art HD/VSA functionality, clear documentation, and implementation examples from well-known publications. Comparing publicly available code with their corresponding Torchhd implementation shows that experiments can run up to 100x faster. Torchhd is available at: https://github.com/hyperdimensional-computing/torchhd. △ Less

Submitted 21 July, 2023; v1 submitted 18 May, 2022; originally announced May 2022.

Journal ref: Journal of Machine Learning Research 24 (2023) 1--10

Efficient Off-Policy Reinforcement Learning via Brain-Inspired Computing

Authors: Yang Ni, Danny Abraham, Mariam Issa, Yeseong Kim, Pietro Mercati, Mohsen Imani

Abstract: Reinforcement Learning (RL) has opened up new opportunities to enhance existing smart systems that generally include a complex decision-making process. However, modern RL algorithms, e.g., Deep Q-Networks (DQN), are based on deep neural networks, resulting in high computational costs. In this paper, we propose QHD, an off-policy value-based Hyperdimensional Reinforcement Learning, that mimics brai… ▽ More Reinforcement Learning (RL) has opened up new opportunities to enhance existing smart systems that generally include a complex decision-making process. However, modern RL algorithms, e.g., Deep Q-Networks (DQN), are based on deep neural networks, resulting in high computational costs. In this paper, we propose QHD, an off-policy value-based Hyperdimensional Reinforcement Learning, that mimics brain properties toward robust and real-time learning. QHD relies on a lightweight brain-inspired model to learn an optimal policy in an unknown environment. On both desktop and power-limited embedded platforms, QHD achieves significantly better overall efficiency than DQN while providing higher or comparable rewards. QHD is also suitable for highly-efficient reinforcement learning with great potential for online and real-time learning. Our solution supports a small experience replay batch size that provides 12.3 times speedup compared to DQN while ensuring minimal quality loss. Our evaluation shows QHD capability for real-time learning, providing 34.6 times speedup and significantly better quality of learning than DQN. △ Less

Submitted 21 June, 2023; v1 submitted 14 May, 2022; originally announced May 2022.

Comments: In Proceedings of the Great Lakes Symposium on VLSI 2023(GLSVLSI 2023)

Scattering statistics of rock outcrops: Model-data comparisons and Bayesian inference using mixture distributions

Authors: Derek R. Olson, Anthony P. Lyons, Douglas A. Abraham, Torstein O. Sæbø

Abstract: The probability density function of the acoustic field amplitude scattered by the seafloor was measured in a rocky environment off the coast of Norway using a synthetic aperture sonar system, and is reported here in terms of the probability of false alarm. Interpretation of the measurements focused on finding appropriate class of statistical models (single versus two-component mixture models), and… ▽ More The probability density function of the acoustic field amplitude scattered by the seafloor was measured in a rocky environment off the coast of Norway using a synthetic aperture sonar system, and is reported here in terms of the probability of false alarm. Interpretation of the measurements focused on finding appropriate class of statistical models (single versus two-component mixture models), and on appropriate models within these two classes. It was found that two-component mixture models performed better than single models. The two mixture models that performed the best (and had a basis in the physics of scattering) were a mixture between two K distributions, and a mixture between a Rayleigh and generalized Pareto distribution. Bayes' theorem was used to estimate the probability density function of the mixture model parameters. It was found that the K-K mixture exhibits significant correlation between its parameters. The mixture between the Rayleigh and generalized Pareto distributions also had significant parameter correlation, but also contained multiple modes. We conclude that the mixture between two K distributions is the most applicable to this dataset. △ Less

Submitted 23 January, 2019; originally announced January 2019.

Comments: 15 pages, 7 figures, Accepted to the Journal of the Acoustical Society of America

Lost Waterways: Clues from Digitized Historical Maps of Manila and Other Philippine Cities

Authors: K. G. Jubilo, M. R. Algodon, E. M. Torres, Z. D. Abraham, A. Ide-Ektessabi, M. Soriano

Abstract: We search for lost bodies of water in the cities of Manila, Tacloban, Iloilo, Cebu, Davao, and Naga by aligning their digitized Spanish-era and American-era maps to Google maps. These vanished ancient waterways can either become flooding hazards in case of extreme weather events, or liquefaction hazards, in case of earthquakes. Digitized historical maps of the cities were georectified, overlaid on… ▽ More We search for lost bodies of water in the cities of Manila, Tacloban, Iloilo, Cebu, Davao, and Naga by aligning their digitized Spanish-era and American-era maps to Google maps. These vanished ancient waterways can either become flooding hazards in case of extreme weather events, or liquefaction hazards, in case of earthquakes. Digitized historical maps of the cities were georectified, overlaid on current Google maps, and checked for potential missing bodies of water. Inspection through field visits and interviews with locals were conducted to verify the actual status of suspected sites. The validation identified lost, found, and even new bodies of water. There was also evidence of affected buildings, rainless flooding, and a new normal for the meaning of flooding among frequently inundated residents. △ Less

Submitted 13 December, 2018; originally announced December 2018.

A continuum of pure states in the Ising model on a halfplane

Authors: Douglas Abraham, Charles M. Newman, Senya Shlosman

Abstract: We study the homogeneous nearest-neighbor Ising ferromagnet on the right half plane with a Dobrushin type boundary condition --- say plus on the top part of the boundary and minus on the bottom. For sufficiently low temperature $T$, we completely characterize the pure (i.e., extremal) Gibbs states, as follows. There is exactly one for each angle $θ\in\lbrack-π/2,+π/2]$; here $θ$ specifies the asym… ▽ More We study the homogeneous nearest-neighbor Ising ferromagnet on the right half plane with a Dobrushin type boundary condition --- say plus on the top part of the boundary and minus on the bottom. For sufficiently low temperature $T$, we completely characterize the pure (i.e., extremal) Gibbs states, as follows. There is exactly one for each angle $θ\in\lbrack-π/2,+π/2]$; here $θ$ specifies the asymptotic angle of the interface separating regions where the spin configuration looks like that of the plus (respectively, minus) full-plane state. Some of these conclusions are extended all the way to $T=T_{c}$ by develo** new Ising exact solution result -- in particular, there is at least one pure state for each $θ$. △ Less

Submitted 12 November, 2017; v1 submitted 15 October, 2017; originally announced October 2017.

Comments: In this version, a discussion of the 3D case is included

MSC Class: 82B20

Action at a distance in classical uniaxial ferromagnetic arrays

Authors: D. B. Abraham, A. Maciołek, A. Squarcini, O. Vasilyev

Abstract: We examine in detail the theoretical foundations of striking long-range couplings emerging in arrays of fluid cells connected by narrow channels by using a lattice gas (Ising model) description of a system. We present a reexamination of the well known exact determination of the two-point correlation function along the edge of a channel using the transfer matrix technique and a new interpretation i… ▽ More We examine in detail the theoretical foundations of striking long-range couplings emerging in arrays of fluid cells connected by narrow channels by using a lattice gas (Ising model) description of a system. We present a reexamination of the well known exact determination of the two-point correlation function along the edge of a channel using the transfer matrix technique and a new interpretation is provided. The explicit form of the correlation length is found to grow exponentially with the cross section of the channels at the bulk two-phase coexistence. The aforementioned result is recaptured by a refined version of the Fisher-Privman theory of first order phase transitions in which the Boltzmann factor for a domain wall is decorated with a contribution stemming from the point tension originated at its endpoints. The Boltzmann factor for a domain wall together with the point tension is then identified exactly thanks to two independent analytical techniques, providing a critical test of the Fisher-Privman theory. We then illustrate how to build up the network model from its elementary constituents, the cells and the channels. Moreover, we are able to extract the strength of the coupling between cells and express them in terms of the length and width and coarse grained quantities such as surface and point tensions. We then support our theoretical investigation with a series of corroborating results based on Monte Carlo simulations. We illustrate how the long range ordering occurs and how the latter is signaled by the thermodynamic quantities corresponding to both planar and three-dimensional Ising arrays. △ Less

Submitted 3 July, 2017; originally announced July 2017.

Comments: 36 pages, 19 figures

Journal ref: Phys. Rev. E 96, 042154 (2017)

A Correction Function Method for the Wave Equation with Interface Jump Conditions

Authors: David S. Abraham, Alexandre Noll Marques, Jean-Christophe Nave

Abstract: In this paper a novel method to solve the constant coefficient wave equation, subject to interface jump conditions, is presented. In general, such problems pose issues for standard finite difference solvers, as the inherent discontinuity in the solution results in erroneous derivative information wherever the stencils straddle the given interface. Here, however, the recently proposed Correction Fu… ▽ More In this paper a novel method to solve the constant coefficient wave equation, subject to interface jump conditions, is presented. In general, such problems pose issues for standard finite difference solvers, as the inherent discontinuity in the solution results in erroneous derivative information wherever the stencils straddle the given interface. Here, however, the recently proposed Correction Function Method (CFM) is used, in which correction terms are computed from the interface conditions, and added to affected nodes to compensate for the discontinuity. In contrast to existing methods, these corrections are not simply defined at affected nodes, but rather generalized to a continuous function within a small region surrounding the interface. As a result, the correction function may be defined in terms of its own governing partial differential equation (PDE) which may be solved, in principle, to arbitrary order of accuracy. The resulting scheme is not only arbitrarily high order, but also robust, having already seen application to Poisson problems and the heat equation. By extending the CFM to this new class of PDEs, the treatment of wave interface discontinuities in homogeneous media becomes possible. This allows, for example, for the straightforward treatment of infinitesimal source terms and sharp boundaries, free of staircasing errors. Additionally, new modifications to the CFM are derived, allowing compatibility with explicit multi-step methods, such as Runge-Kutta (RK4), without a reduction in accuracy. These results are then verified through numerous numerical experiments in one and two spatial dimensions. △ Less

Submitted 20 December, 2016; v1 submitted 17 September, 2016; originally announced September 2016.

Comments: 31 pages, 19 figures; clarified certain sections of the text, results unchanged

MSC Class: 35L05; 65M06

Stress Evolution in Lithium-ion Composite Electrodes during Electrochemical Cycling and Resulting Internal Pressures on the Cell Casing

Authors: Siva P. V. Nadimpalli, Vijay A. Sethuraman, Daniel P. Abraham, Allan F. Bower, Pradeep R. Guduru

Abstract: Composite cathode coatings made of a high energy density layered oxide (Li1.2Ni0.15Mn0.55Co0.1O2, theoretical capacity ~377 mAh/g), polyvinylidene fluoride (PVdF) binder, and electron-conduction additives, were bonded to an elastic substrate. An electrochemical cell, built by pairing the cathode with a capacity-matched graphite anode, was electrochemically cycled and the real-time average stress e… ▽ More Composite cathode coatings made of a high energy density layered oxide (Li1.2Ni0.15Mn0.55Co0.1O2, theoretical capacity ~377 mAh/g), polyvinylidene fluoride (PVdF) binder, and electron-conduction additives, were bonded to an elastic substrate. An electrochemical cell, built by pairing the cathode with a capacity-matched graphite anode, was electrochemically cycled and the real-time average stress evolution in the cathode coating was measured using a substrate-curvature technique. Features in the stress evolution profile showed correlations with phase changes in the oxide, thus yielding data complementary to in situ XRD studies on this material. The stress evolution showed a complex variation with lithium concentration suggesting that the volume changes associated with phase transformations in the oxide are not monotonically varying functions of lithium concentration. The peak tensile stress in the cathode during oxide delithiation was approximately 1.5 MPa and the peak compressive stress during oxide lithiation was about 6 MPa. Stress evolution in the anode coating was also measured separately using the same technique. The measured stresses are used to estimate the internal pressures that develop in a cylindrical lithium-ion cell with jelly-roll electrodes. △ Less

Submitted 8 November, 2015; originally announced November 2015.

Comments: 23 pages, 9 figures

Journal ref: Journal of The Electrochemical Society, 162 (14), A2656-A2663, 2015

Bulk and surface loss in superconducting transmon qubits

Authors: Oliver Dial, Douglas T. McClure, Stefano Poletto, Jay M. Gambetta, David W. Abraham, Jerry M. Chow, Matthias Steffen

Abstract: Decoherence of superconducting transmon qubits is purported to be consistent with surface loss from two-level systems on the substrate surface. Here, we present a study of surface loss in transmon devices, explicitly designed to have varying sensitivities to different surface loss contributors. Our experiments also encompass two particular different sapphire substrates, which reveal the onset of a… ▽ More Decoherence of superconducting transmon qubits is purported to be consistent with surface loss from two-level systems on the substrate surface. Here, we present a study of surface loss in transmon devices, explicitly designed to have varying sensitivities to different surface loss contributors. Our experiments also encompass two particular different sapphire substrates, which reveal the onset of a yet unknown additional loss mechanism outside of surface loss for one of the substrates. Tests across different wafers and devices demonstrate substantial variation, and we emphasize the importance of testing large numbers of devices for disentangling different sources of decoherence. △ Less

Submitted 13 September, 2015; originally announced September 2015.

Comments: 4 pages, 3 figures

Journal ref: Superconductor Science and Technology, 29(4) 044001 (2016)

Characterizing a Four-Qubit Planar Lattice for Arbitrary Error Detection

Authors: Jerry M. Chow, Srikanth J. Srinivasan, Easwar Magesan, A D. Corcoles, David W. Abraham, Jay M. Gambetta, Matthias Steffen

Abstract: Quantum error correction will be a necessary component towards realizing scalable quantum computers with physical qubits. Theoretically, it is possible to perform arbitrarily long computations if the error rate is below a threshold value. The two-dimensional surface code permits relatively high fault-tolerant thresholds at the ~1% level, and only requires a latticed network of qubits with nearest-… ▽ More Quantum error correction will be a necessary component towards realizing scalable quantum computers with physical qubits. Theoretically, it is possible to perform arbitrarily long computations if the error rate is below a threshold value. The two-dimensional surface code permits relatively high fault-tolerant thresholds at the ~1% level, and only requires a latticed network of qubits with nearest-neighbor interactions. Superconducting qubits have continued to steadily improve in coherence, gate, and readout fidelities, to become a leading candidate for implementation into larger quantum networks. Here we describe characterization experiments and calibration of a system of four superconducting qubits arranged in a planar lattice, amenable to the surface code. Insights into the particular qubit design and comparison between simulated parameters and experimentally determined parameters are given. Single- and two-qubit gate tune-up procedures are described and results for simultaneously benchmarking pairs of two-qubit gates are given. All controls are eventually used for an arbitrary error detection protocol described in separate work [Corcoles et al., Nature Communications, 6, 2015] △ Less

Submitted 9 September, 2015; originally announced September 2015.

Comments: 9 pages, 3 figures in Proc. SPIE 9500, Quantum Information and Computation XIII, 95001G (May 21, 2015)

Apparent first-order wetting and anomalous scaling in the two-dimensional Ising model

Authors: X. T. Wu, D. B. Abraham, J. O. Indekeu

Abstract: The global phase diagram of wetting in the two-dimensional (2d) Ising model is obtained through exact calculation of the surface excess free energy. Besides a surface field for inducing wetting, a surface-coupling enhancement is included. The wetting transition is critical (second order) for any finite ratio of surface coupling J_s to bulk coupling J, and turns first order in the limit J_s/J to in… ▽ More The global phase diagram of wetting in the two-dimensional (2d) Ising model is obtained through exact calculation of the surface excess free energy. Besides a surface field for inducing wetting, a surface-coupling enhancement is included. The wetting transition is critical (second order) for any finite ratio of surface coupling J_s to bulk coupling J, and turns first order in the limit J_s/J to infinity. However, for J_s/J much larger than 1 the critical region is exponentially small and practically invisible to numerical studies. A distinct pre-asymptotic regime exists in which the transition displays first-order character. Surprisingly, in this regime the surface susceptibility and surface specific heat develop a divergence and show anomalous scaling with an exponent equal to 3/2. △ Less

Submitted 3 January, 2016; v1 submitted 30 October, 2014; originally announced October 2014.

Comments: This new version presents the exact solution and its properties whereas the older version was based on an approximate numerical study of the model

Journal ref: Phys. Rev. Lett. 116, 046101 (2016)

Action at the distance

Authors: D. B. Abraham, A. Maciolek, O. Vasilyev

Abstract: We present a system exhibiting giant proximity effects which parallel observations in superfluid helium (Perron et al, Nature Physics V. 6, 499 (2010)) and give a theoretical explanation of these phenomena based on the mesoscopic picture of phase coexistence in finite systems. Our theory is confirmed by MC simulation studies. Our work demonstrates that such action-at-a-distance can occur in classi… ▽ More We present a system exhibiting giant proximity effects which parallel observations in superfluid helium (Perron et al, Nature Physics V. 6, 499 (2010)) and give a theoretical explanation of these phenomena based on the mesoscopic picture of phase coexistence in finite systems. Our theory is confirmed by MC simulation studies. Our work demonstrates that such action-at-a-distance can occur in classical systems involving simple or complex fluids, such as colloid-polymer mixtures, or ferromagnets. △ Less

Submitted 21 May, 2014; originally announced May 2014.

Blackbox Quantization of Superconducting Circuits using exact Impedance Synthesis

Authors: Firat Solgun, David W. Abraham, David P. DiVincenzo

Abstract: We propose a new quantization method for superconducting electronic circuits involving a Josephson junction device coupled to a linear microwave environment. The method is based on an exact impedance synthesis of the microwave environment considered as a blackbox with impedance function Z(s). The synthesized circuit captures dissipative dynamics of the system with resistors coupled to the reactive… ▽ More We propose a new quantization method for superconducting electronic circuits involving a Josephson junction device coupled to a linear microwave environment. The method is based on an exact impedance synthesis of the microwave environment considered as a blackbox with impedance function Z(s). The synthesized circuit captures dissipative dynamics of the system with resistors coupled to the reactive part of the circuit in a non-trivial way. We quantize the circuit and compute relaxation rates following previous formalisms for lumped element circuit quantization. Up to the errors in the fit our method gives an exact description of the system and its losses. △ Less

Submitted 28 March, 2014; originally announced March 2014.

Implementing a strand of a scalable fault-tolerant quantum computing fabric

Authors: Jerry M. Chow, Jay M. Gambetta, Easwar Magesan, Srikanth J. Srinivasan, Andrew W. Cross, David W. Abraham, Nicholas A. Masluk, B. R. Johnson, Colm A. Ryan, M. Steffen

Abstract: Quantum error correction (QEC) is an essential step towards realising scalable quantum computers. Theoretically, it is possible to achieve arbitrarily long protection of quantum information from corruption due to decoherence or imperfect controls, so long as the error rate is below a threshold value. The two-dimensional surface code (SC) is a fault-tolerant error correction protocol} that has garn… ▽ More Quantum error correction (QEC) is an essential step towards realising scalable quantum computers. Theoretically, it is possible to achieve arbitrarily long protection of quantum information from corruption due to decoherence or imperfect controls, so long as the error rate is below a threshold value. The two-dimensional surface code (SC) is a fault-tolerant error correction protocol} that has garnered considerable attention for actual physical implementations, due to relatively high error thresholds ~1%, and restriction to planar lattices with nearest-neighbour interactions. Here we show a necessary element for SC error correction: high-fidelity parity detection of two code qubits via measurement of a third syndrome qubit. The experiment is performed on a sub-section of the SC lattice with three superconducting transmon qubits, in which two independent outer code qubits are joined to a central syndrome qubit via two linking bus resonators. With all-microwave high-fidelity single- and two-qubit nearest-neighbour entangling gates, we demonstrate entanglement distributed across the entire sub-section by generating a three-qubit Greenberger-Horne-Zeilinger (GHZ) state with fidelity ~94%. Then, via high-fidelity measurement of the syndrome qubit, we deterministically entangle the otherwise un-coupled outer code qubits, in either an even or odd parity Bell state, conditioned on the syndrome state. Finally, to fully characterize this parity readout, we develop a new measurement tomography protocol to obtain a fidelity metric (90% and 91%). Our results reveal a straightforward path for expanding superconducting circuits towards larger networks for the SC and eventually a primitive logical qubit implementation. △ Less

Submitted 25 November, 2013; originally announced November 2013.

Comments: 9 pages, 4 main figures, 3 extended data figures

Journal ref: Nature Communications 5, 4015 (2014)

Stress Evolution in Composite Silicon Electrodes during Lithiation/Delithiation

Authors: Vijay A. Sethuraman, Annam Nguyen, Michael J. Chon, Siva P. V. Nadimpalli, Hailong Wang, Daniel P. Abraham, Allan F. Bower, Vivek B. Shenoy, Pradeep R. Guduru

Abstract: We report real-time average stress measurements on composite silicon electrodes made with two different binders [Carboxymethyl cellulose (CMC), and polyvinylidene fluoride (PVDF)] during electrochemical lithiation and delithiation. During galvanostatic lithiation at very slow rates, the stress in a CMC-based electrode becomes compressive and increases to 70 MPa, where it reaches a plateau and incr… ▽ More We report real-time average stress measurements on composite silicon electrodes made with two different binders [Carboxymethyl cellulose (CMC), and polyvinylidene fluoride (PVDF)] during electrochemical lithiation and delithiation. During galvanostatic lithiation at very slow rates, the stress in a CMC-based electrode becomes compressive and increases to 70 MPa, where it reaches a plateau and increases slowly thereafter with capacity. The PVDF-based electrode exhibits similar behavior, although with lower peak compressive stress of about 12 MPa. These initial experiments indicate that the stress evolution in a Si composite electrode depends strongly on the mechanical properties of the binder. Stress data obtained from a series of lithiation/delithiation cycles suggests plasticity induced irreversible shape changes in contacting Si particles, and as a result, the stress response of the system during any given lithiation/delithiation cycle depends on the cycling history of the electrode. While these results constitute the first in-situ stress measurements on composite Si electrodes during electrochemical cycling, the diagnostic technique described herein can be used to assess the mechanical response of a composite electrode made with other active material/binder combinations. △ Less

Submitted 18 August, 2013; originally announced August 2013.

Comments: 22 pages, 8 figures

Journal ref: Journal of The Electrochemical Society, 160 (4), A739-A746, 2013

Collective Effects in Linear Spectroscopy of Dipole-Coupled Molecular Arrays

Authors: A. A. Kocherzhenko, J. Dawlaty, B. P. Abolins, F. Herrera, D. B. Abraham, K. B. Whaley

Abstract: We present a consistent analysis of linear spectroscopy for arrays of nearest neighbor dipole-coupled two-level molecules that reveals distinct signatures of weak and strong coupling regimes separated for infinite size arrays by a quantum critical point. In the weak coupling regime, the ground state of the molecular array is disordered, but in the strong coupling regime it has (anti)ferroelectric… ▽ More We present a consistent analysis of linear spectroscopy for arrays of nearest neighbor dipole-coupled two-level molecules that reveals distinct signatures of weak and strong coupling regimes separated for infinite size arrays by a quantum critical point. In the weak coupling regime, the ground state of the molecular array is disordered, but in the strong coupling regime it has (anti)ferroelectric ordering. We show that multiple molecular excitations (odd/even in weak/strong coupling regime) can be accessed directly from the ground state. We analyze the scaling of absorption and emission with system size and find that the oscillator strengths show enhanced superradiant behavior in both ordered and disordered phases. As the coupling increases, the single excitation oscillator strength rapidly exceeds the well known Heitler-London value. In the strong coupling regime we show the existence of a unique spectral transition with excitation energy that can be tuned by varying the system size and that asymptotically approaches zero for large systems. The oscillator strength for this transition scales quadratically with system size, showing an anomalous one-photon superradiance. For systems of infinite size, we find a novel, singular spectroscopic signature of the quantum phase transition between disordered and ordered ground states. We outline how arrays of ultra cold dipolar molecules trapped in an optical lattice can be used to access the strong coupling regime and observe the anomalous superradiant effects associated with this regime. △ Less

Submitted 16 October, 2014; v1 submitted 10 July, 2013; originally announced July 2013.

Comments: 12 pages, 7 figures main text

Quasi-One-Dimensional Thermal Breakage

Authors: Cristiano Nisoli, Douglas Abraham, Turab Lookman, Avadh Saxena

Abstract: Breakage is generally understood in mechanical terms, yet nano-structures can rupture not only under external loads but also via thermal activation. Here we treat in a general framework the statistical mechanics of thermally induced breakage at the nano-scale for one-dimensional systems. We test it on a simple approximation and find that the probability of breakage controls distinct regimes, chara… ▽ More Breakage is generally understood in mechanical terms, yet nano-structures can rupture not only under external loads but also via thermal activation. Here we treat in a general framework the statistical mechanics of thermally induced breakage at the nano-scale for one-dimensional systems. We test it on a simple approximation and find that the probability of breakage controls distinct regimes, characterized by sharp crossovers and narrow peaks in the thermal fluctuations and specific heat. Our work provides predictions on clustering of new phases, of relevance in nano-fabrication. △ Less

Submitted 18 October, 2014; v1 submitted 24 June, 2013; originally announced June 2013.

Comments: 7 Pages 6 Figures

Journal ref: Physical Review E 88 (4), 042409 (2014)

Improved superconducting qubit coherence using titanium nitride

Authors: J. Chang, M. R. Vissers, A. D. Corcoles, M. Sandberg, J. Gao, David W. Abraham, Jerry M. Chow, Jay M. Gambetta, M. B. Rothwell, G. A. Keefe, Matthias Steffen, D. P. Pappas

Abstract: We demonstrate enhanced relaxation and dephasing times of transmon qubits, up to ~ 60 μs by fabricating the interdigitated shunting capacitors using titanium nitride (TiN). Compared to lift-off aluminum deposited simultaneously with the Josephson junction, this represents as much as a six-fold improvement and provides evidence that previous planar transmon coherence times are limited by surface lo… ▽ More We demonstrate enhanced relaxation and dephasing times of transmon qubits, up to ~ 60 μs by fabricating the interdigitated shunting capacitors using titanium nitride (TiN). Compared to lift-off aluminum deposited simultaneously with the Josephson junction, this represents as much as a six-fold improvement and provides evidence that previous planar transmon coherence times are limited by surface losses from two-level system (TLS) defects residing at or near interfaces. Concurrently, we observe an anomalous temperature dependent frequency shift of TiN resonators which is inconsistent with the predicted TLS model. △ Less

Submitted 17 March, 2013; originally announced March 2013.

Comments: 3 figures

Journal ref: Appl. Phys. Lett. 103, 012602 (2013)

Entanglement of two superconducting qubits in a waveguide cavity via monochromatic two-photon excitation

Authors: S. Poletto, Jay M. Gambetta, Seth T. Merkel, John A. Smolin, Jerry M. Chow, A. D. Corcoles, George A. Keefe, Mary B. Rothwell, J. R. Rozen, D. W. Abraham, Chad Rigetti, M. Steffen

Abstract: We report a system where fixed interactions between non-computational levels make bright the otherwise forbidden two-photon 00 --> 11 transition. The system is formed by hand selection and assembly of two discrete component transmon-style superconducting qubits inside a rectangular microwave cavity. The application of a monochromatic drive tuned to this transition induces two-photon Rabi-like osci… ▽ More We report a system where fixed interactions between non-computational levels make bright the otherwise forbidden two-photon 00 --> 11 transition. The system is formed by hand selection and assembly of two discrete component transmon-style superconducting qubits inside a rectangular microwave cavity. The application of a monochromatic drive tuned to this transition induces two-photon Rabi-like oscillations between the ground and doubly-excited states via the Bell basis. The system therefore allows all-microwave two-qubit universal control with the same techniques and hardware required for single qubit control. We report Ramsey-like and spin echo sequences with the generated Bell states, and measure a two-qubit gate fidelity of 90% (unconstrained) and 86% (maximum likelihood estimator). △ Less

Submitted 12 November, 2012; v1 submitted 6 August, 2012; originally announced August 2012.

Comments: 5 pages, 4 figures. V2: add supplemental material about the Schrieffer-Wolff transformation

Journal ref: Phys. Rev. Lett. 109, 240505 (2012)

Surface states and the thermal Casimir interaction

Authors: Douglas B. Abraham, Anna Maciolek

Abstract: Using exact calculations, we elucidate the significance of the surface (bound) states for the thermal Casimir interactions for an Ising strip with a finite width. The surface state arises whenever an imaginary wavenumber mode appears in the spectrum of the transfer matrix, taken in the direction parallel to the edges of the strip. Depending on the boundary conditions, the imaginary modes emerge be… ▽ More Using exact calculations, we elucidate the significance of the surface (bound) states for the thermal Casimir interactions for an Ising strip with a finite width. The surface state arises whenever an imaginary wavenumber mode appears in the spectrum of the transfer matrix, taken in the direction parallel to the edges of the strip. Depending on the boundary conditions, the imaginary modes emerge below or above the bulk critical temperature, or below the wetting temperature of a single surface with surface magnetic field. The bound states are responsible for the strong asymmetry of the Casimir forces between the super- and sub-critical regimes and for their sign. Our analysis uses the fact that the Casimir forces have two mathematical forms. We show that these very different representation are the same and in the process find the origin of the asymmetry. △ Less

Submitted 25 June, 2012; originally announced June 2012.

Comments: 2 figures

Computational Study of a Multistep Height Model

Authors: Matthew Drake, Jon Machta, You** Deng, Douglas Abraham, Charles Newman

Abstract: An equilibrium random surface multistep height model proposed in [Abraham and Newman, EPL, 86, 16002 (2009)] is studied using a variant of the worm algorithm. In one limit, the model reduces to the two-dimensional Ising model in the height representation. When the Ising model constraint of single height steps is relaxed, the critical temperature and critical exponents are continuously varying func… ▽ More An equilibrium random surface multistep height model proposed in [Abraham and Newman, EPL, 86, 16002 (2009)] is studied using a variant of the worm algorithm. In one limit, the model reduces to the two-dimensional Ising model in the height representation. When the Ising model constraint of single height steps is relaxed, the critical temperature and critical exponents are continuously varying functions of the parameter controlling height steps larger than one. Numerical estimates of the critical exponents can be mapped via a single parameter-- the Coulomb gas coupling-- to the exponents of the O(n) loop model on the honeycomb lattice with n <= 1. △ Less

Submitted 2 July, 2012; v1 submitted 18 March, 2012; originally announced March 2012.

Comments: 13 pages, 6 figures; v2 includes small edits

Journal ref: Phys. Rev. E 85, 061104 (2012)

Real-Time Stress Measurements in Lithium-ion Battery Negative-electrodes

Authors: Vijay A. Sethuraman, Nathan Van Winkle, Daniel P. Abraham, Allan F. Bower, Pradeep R. Guduru

Abstract: Real-time stress evolution in a graphite-based lithium-ion battery negative-electrode during electrolyte wetting and electrochemical cycling is measured through wafer-curvature method. Upon electrolyte addition, the composite electrode rapidly develops compressive stress of the order of 1-2 MPa due to binder swelling; upon continued exposure, the stress continues to evolve towards an apparent plat… ▽ More Real-time stress evolution in a graphite-based lithium-ion battery negative-electrode during electrolyte wetting and electrochemical cycling is measured through wafer-curvature method. Upon electrolyte addition, the composite electrode rapidly develops compressive stress of the order of 1-2 MPa due to binder swelling; upon continued exposure, the stress continues to evolve towards an apparent plateau. During electrochemical intercalation at a slow rate, the compressive stress increases with the electrode's state-of-charge, reaching a maximum value of 10 - 12 MPa. There appears to be an approximate correlation between the rate of stress rise and the staging behavior of the lithiated graphite. De-intercalation at a slow rate results in a similar linear decrease in electrode stress. Tensile stress of a few MPa develops at the end of deintercalation in the first few cycles, after which the electrode remains under compressive stress only. Although higher peak stresses are seen at high C-rates, the dependence appears to be relatively weak (up to 5C). These measurements reveal, for the first time, the nature of stress evolution in practical lithium-ion-battery electrodes and provide useful data to quantify the driving force for mechanical damage that accrues in composite electrodes upon repeated cycling. While the reported results can serve as reference for calibrating theoretical and computational models to predict electrode stress and damage evolution, the methodology demonstrated can be used to measure stresses and characterize fatigue damage in any composite lithium-ion-battery electrode as well as optimize its microstructure to mitigate stress-related damage mechanisms. △ Less

Submitted 10 January, 2012; originally announced January 2012.

Comments: 22 pages, 8 figures; Journal of Power Sources, 201, 2012

Journal ref: Journal of Power Sources, 206, 334-342, 2012

Controls over Spreadsheets for Financial Reporting in Practice

Authors: Nancy Coster, Linda Leon, Lawrence Kalbers, Dolphy Abraham

Abstract: Past studies show that only a small percent of organizations implement and enforce formal rules or informal guidelines for the designing, testing, documenting, using, modifying, sharing and archiving of spreadsheet models. Due to lack of such policies, there has been little research on how companies can effectively govern spreadsheets throughout their life cycle. This paper describes a survey invo… ▽ More Past studies show that only a small percent of organizations implement and enforce formal rules or informal guidelines for the designing, testing, documenting, using, modifying, sharing and archiving of spreadsheet models. Due to lack of such policies, there has been little research on how companies can effectively govern spreadsheets throughout their life cycle. This paper describes a survey involving 38 participants from the United States, representing companies that were working on compliance with the Sarbanes-Oxley Act of 2002 (SOX) as it relates to spreadsheets for financial reporting. The findings of this survey describe specific controls organizations have implemented to manage spreadsheets for financial reporting throughout the spreadsheet's lifecycle. Our findings indicate that there are problems in all stages of a spreadsheet's life cycle and suggest several important areas for future research. △ Less

Submitted 29 November, 2011; originally announced November 2011.

Comments: 13Pages, 4 Tables, 1 Colour Figure; Proc. European Spreadsheet Risks Int. Grp. (EuSpRIG) 2011 ISBN 978-0-9566256-9-4

Thermoelectric Spin-Transfer Torque MRAM with Sub-Nanosecond Bi-Directional Writing using Magnonic Current

Authors: Niladri N. Mojumder, Kaushik Roy, David W. Abraham

Abstract: A new genre of Spin-Transfer Torque (STT) MRAM is proposed, in which bi-directional writing is achieved using thermoelectrically controlled magnonic current as an alternative to conventional electric current. The device uses a magnetic tunnel junction (MTJ), which is adjacent to a non-magnetic metallic and a ferrite film. This film stack is heated or cooled by a Peltier element which creates a bi-… ▽ More A new genre of Spin-Transfer Torque (STT) MRAM is proposed, in which bi-directional writing is achieved using thermoelectrically controlled magnonic current as an alternative to conventional electric current. The device uses a magnetic tunnel junction (MTJ), which is adjacent to a non-magnetic metallic and a ferrite film. This film stack is heated or cooled by a Peltier element which creates a bi-directional magnonic pulse in the ferrite film. Conversion of magnons to spin current occurs at the ferrite-metal interface, and the resulting spin-transfer torque is used to achieve sub-nanosecond precessional switching of the ferromagnetic free layer in the MTJ. Compared to electric current driven STT-MRAM with perpendicular magnetic anisotropy (PMA), thermoelectric STT-MRAM reduces the overall magnetization switching energy by more than 40% for nano-second switching, combined with a write error rate (WER) of less than 10-9 and a lifetime of 10 years or higher. The combination of higher thermal activation energy, sub-nanosecond read/write speed, improved tunneling magneto-resistance (TMR) and tunnel barrier reliability make thermoelectric STT-MRAM a promising choice for future non-volatile memory applications. △ Less

Submitted 11 August, 2011; originally announced August 2011.

Magnonic spin-transfer torque MRAM with low power, high speed, and error-free switching

Authors: Niladri N. Mojumder, David W. Abraham, Kaushik Roy, D. C. Worledge

Abstract: A new class of spin-transfer torque magnetic random access memory (STT-MRAM) is discussed, in which writing is achieved using thermally initiated magnonic current pulses as an alternative to conventional electric current pulses. The magnonic pulses are used to destabilize the magnetic free layer from its initial direction, and are followed immediately by a bipolar electric current exerting convent… ▽ More A new class of spin-transfer torque magnetic random access memory (STT-MRAM) is discussed, in which writing is achieved using thermally initiated magnonic current pulses as an alternative to conventional electric current pulses. The magnonic pulses are used to destabilize the magnetic free layer from its initial direction, and are followed immediately by a bipolar electric current exerting conventional spin-transfer torque on the free layer. The combination of thermal and electric currents greatly reduces switching errors, and simultaneously reduces the electric switching current density by more than an order of magnitude as compared to conventional STT-MRAM. The energy efficiency of several possible electro-thermal circuit designs have been analyzed numerically. As compared to STT-MRAM with perpendicular magnetic anisotropy, magnonic STT-MRAM reduces the overall switching energy by almost 80%. Furthermore, the lower electric current density allows the use of thicker tunnel barriers, which should result in higher tunneling magneto-resistance and improved tunnel barrier reliability. The combination of lower power, improved reliability, higher integration density, and larger read margin make magnonic STT-MRAM a promising choice for future non-volatile storage. △ Less

Submitted 26 May, 2011; originally announced May 2011.

Comments: 9 Pages, 11 Figures

Boundary conditions and the critical Casimir force on an Ising model film: exact results in one and two dimensions

Authors: Roya Zandi, Joseph Rudnick, Aviva Shackell, Douglas Abraham

Abstract: Finite size effect in critical systems can be interpreted as universal Casimir forces. Here we compare the Casimir force for free, periodic and antiperiodic boundary conditions in the exactly calculable case of the Ising model in one and two dimensions. We employ a new procedure which allows us to calculate the Casimir force with periodic and antiperiodic boundary conditions analytically in a tr… ▽ More Finite size effect in critical systems can be interpreted as universal Casimir forces. Here we compare the Casimir force for free, periodic and antiperiodic boundary conditions in the exactly calculable case of the Ising model in one and two dimensions. We employ a new procedure which allows us to calculate the Casimir force with periodic and antiperiodic boundary conditions analytically in a transparent manner. Quite interestingly, we find an attractive Casimir force for the case of periodic boundary condition but a repulsive Casimir force for the anti-periodic one. △ Less

Submitted 6 January, 2010; originally announced January 2010.

Comments: 18 page, 10 figures

Casimir interactions in Ising strips with boundary fields: exact results

Authors: Douglas B. Abraham, Anna Maciolek

Abstract: An exact statistical mechanical derivation is given of the critical Casimir forces for Ising strips with arbitrary surface fields applied to edges. Our results show that the strength as well as the sign of the force can be controled by varying the temperature or the fields. An interpretation of the results is given in terms of a linked cluster expansion. This suggests a systematic approach for d… ▽ More An exact statistical mechanical derivation is given of the critical Casimir forces for Ising strips with arbitrary surface fields applied to edges. Our results show that the strength as well as the sign of the force can be controled by varying the temperature or the fields. An interpretation of the results is given in terms of a linked cluster expansion. This suggests a systematic approach for deriving the critical Casimir force which can be used in more general models. △ Less

Submitted 1 December, 2009; originally announced December 2009.

Comments: 10 pages, 4 figures

Thermally Induced Local Failures in Quasi-One-Dimensional Systems: Collapse in Carbon Nanotubes, Necking in Nanowires and Opening of Bubbles in DNA

Authors: Cristiano Nisoli, Douglas Abraham, Turab Lookman, Avadh Saxena

Abstract: We present a general framework to explore thermally activated failures in quasi one dimensional systems. We apply it to the collapse of carbon nanotubes, the formation of bottlenecks in nanowires, both of which limit conductance, and the opening of local regions or "bubbles" of base pairs in strands of DNA that are relevant for transcription and danaturation. We predict an exponential behavior f… ▽ More We present a general framework to explore thermally activated failures in quasi one dimensional systems. We apply it to the collapse of carbon nanotubes, the formation of bottlenecks in nanowires, both of which limit conductance, and the opening of local regions or "bubbles" of base pairs in strands of DNA that are relevant for transcription and danaturation. We predict an exponential behavior for the probability of the opening of bubbles in DNA, the average distance between flattened regions of a nanotube or necking in a nanowire as a monotonically decreasing function of temperature, and compute a temperature below which these events become extremely rare. These findings are difficult to obtain numerically, however, they could be accessible experimentally. △ Less

Submitted 20 October, 2009; originally announced October 2009.

Comments: 4 pages, 2 figures, to be submitted

Journal ref: Physical Review Letters 104 (2), 025503 (2010)

Thermal Stability of Strained Nanowires

Authors: Cristiano Nisoli, Douglas Abraham, Turab Lookman, Avadh Saxena

Abstract: Stranski-Krastanov strained islands undergo a shape anisotropy transition as they grow in size, finally evolving toward nanowires. This effect has been explained until now via simple energetic models that neglect thermodynamics. We investigate theoretically the stability of strained nanowires under thermal fluctuations of the long side. We find phase transitions from nanowires back to nanoisland… ▽ More Stranski-Krastanov strained islands undergo a shape anisotropy transition as they grow in size, finally evolving toward nanowires. This effect has been explained until now via simple energetic models that neglect thermodynamics. We investigate theoretically the stability of strained nanowires under thermal fluctuations of the long side. We find phase transitions from nanowires back to nanoislands as the temperature is increased and as the height of the nanostructure is raised or lowered and we predict regions of phase coexistence. Our results are general, but explain recent data on the growth of erbium silicide on a vicinal Si surface. △ Less

Submitted 8 April, 2009; originally announced April 2009.

Journal ref: Physical Review Letters 102 (24), 245504 (2009)

SN 2008S: an electron capture SN from a super-AGB progenitor?

Authors: M. T. Botticella, A. Pastorello, S. J. Smartt, W. P. S. Meikle, S. Benetti, R. Kotak, E. Cappellaro, R. M. Crockett, S. Mattila, M. Sereno, F. Patat, D. Tsvetkov, J. Th. Van Loon, D. Abraham, I. Agnoletto, R. Arbour, C. Benn, G. Di Rico, N. Elias-Rosa, D. L. Gorshanov, A. Harutyunyan, D. Hunter, V. Lorenzi, F. P. Keenan, K. Maguire , et al. (9 additional authors not shown)

Abstract: We present comprehensive photometric and spectroscopic observations of the faint transient SN 2008S discovered in NGC 6946. SN 2008S exhibited slow photometric evolution and almost no spectral variability during the first nine months, implying a high density CS medium. The light curve is similar in shape to that of SN 1998S and SN 1979C, although significantly fainter at maximum light. Our quasi… ▽ More We present comprehensive photometric and spectroscopic observations of the faint transient SN 2008S discovered in NGC 6946. SN 2008S exhibited slow photometric evolution and almost no spectral variability during the first nine months, implying a high density CS medium. The light curve is similar in shape to that of SN 1998S and SN 1979C, although significantly fainter at maximum light. Our quasi-bolometric lightcurve extends to 300 days and shows a tail phase decay rate consistent with that of ^{56}Co. We propose that this is evidence for an explosion and formation of ^{56}Ni (0.0015 +/- 0.0004 M_Sun). The large MIR flux detected shortly after explosion can be explained by a light echo from pre-exisiting dust. The late NIR flux excess is plausibly due to a combination of warm newly-formed ejecta dust together with shock-heated dust in the CS environment. We reassess the progenitor object detected previously in Spitzer archive images, supplementing this discussion with a model of the MIR spectral energy distribution. This supports the idea of a dusty, optically thick shell around SN 2008S with an inner radius of nearly 90AU and outer radius of 450AU, and an inferred heating source of 3000 K and luminosity of L ~ 10^{4.6} L_Sun. The combination of our monitoring data and the evidence from the progenitor analysis leads us to support the scenario of a weak electron capture supernova explosion in a super-AGB progenitor star (of initial mass 6-8 M_sun) embedded within a thick CS gaseous envelope. We suggest that all of main properties of the electron capture SN phenomenon are observed in SN 2008S and future observations may allow a definitive answer. △ Less

Submitted 18 May, 2009; v1 submitted 6 March, 2009; originally announced March 2009.

Comments: accepted for publication in MNRAS (2009 May 7)

Interfaces in driven Ising models: shear enhances confinement

Authors: Thomas H. R. Smith, Oleg Vasilyev, Douglas B. Abraham, Anna Maciołek, Matthias Schmidt

Abstract: We use a phase-separated driven two-dimensional Ising lattice gas to study fluid interfaces exposed to shear flow parallel to the interface. The interface is stabilized by two parallel walls with opposing surface fields and a driving field parallel to the walls is applied which (i) either acts locally at the walls or (ii) varies linearly with distance across the strip. Using computer simulations… ▽ More We use a phase-separated driven two-dimensional Ising lattice gas to study fluid interfaces exposed to shear flow parallel to the interface. The interface is stabilized by two parallel walls with opposing surface fields and a driving field parallel to the walls is applied which (i) either acts locally at the walls or (ii) varies linearly with distance across the strip. Using computer simulations with Kawasaki dynamics, we find that the system reaches a steady state in which the magnetisation profile is the same as that in equilibrium, but with a rescaled length implying a reduction of the interfacial width. An analogous effect was recently observed in sheared phase-separated colloidal dispersions. Pair correlation functions along the interface decay more rapidly with distance under drive than in equilibrium and for cases of weak drive can be rescaled to the equilibrium result. △ Less

Submitted 15 July, 2008; v1 submitted 26 February, 2008; originally announced February 2008.

Comments: 4 pages, 3 figures Text modified, added Fig. 3b. To appear in Phys. Rev. Letters

Effective forces induced by fluctuating interface: exact results

Authors: D. B. Abraham, F. H. L. Essler, A. Maciolek, ;

Abstract: We present exact derivations of the effective capillary wave fluctuation induced forces resulting from pinning of an interface between two coexisting phases at two points separated by a distance r. In two dimensions the Ising ferromagnet calculations based on the transfer matrix approach give an attractive force decaying as 1/r for large distances. In three dimensions map** of the body-centere… ▽ More We present exact derivations of the effective capillary wave fluctuation induced forces resulting from pinning of an interface between two coexisting phases at two points separated by a distance r. In two dimensions the Ising ferromagnet calculations based on the transfer matrix approach give an attractive force decaying as 1/r for large distances. In three dimensions map** of the body-centered solid-on-solid model onto the 6-vertex model allows for exact solution using the bosonization analysis of the equivalent XXZ Heisenberg quantum chain. The exact result gives the attractive force which decays asymptotically as 1/(r\log r). △ Less

Submitted 30 March, 2007; originally announced March 2007.

Comments: 4 pages, 2 figures, accepted for publication in Phys. Rev. Lett

A microscopic model for thin film spreading

Authors: Douglas B. Abraham, Rodolfo Cuerno, Esteban Moro

Abstract: A microscopic, driven lattice gas model is proposed for the dynamics and spatio-temporal fluctuations of the precursor film observed in spreading experiments. Matter is transported both by holes and particles, and the distribution of each can be described by driven diffusion with a moving boundary. This picture leads to a stochastic partial differential equation for the shape of the boundary, wh… ▽ More A microscopic, driven lattice gas model is proposed for the dynamics and spatio-temporal fluctuations of the precursor film observed in spreading experiments. Matter is transported both by holes and particles, and the distribution of each can be described by driven diffusion with a moving boundary. This picture leads to a stochastic partial differential equation for the shape of the boundary, which agrees with the simulations of the lattice gas. Preliminary results for flow in a thermal gradient are discussed. △ Less

Submitted 14 January, 2002; originally announced January 2002.

Comments: 4 pages, 3 figures. Submitted

Journal ref: Physical Review Letters 88, 206101 (2002)

Thickness dependent magnetotransport in ultra-thin manganite films

Authors: J. Z. Sun, D. W. Abraham, R. A. Rao, C. B. Eom

Abstract: To understand the near-interface magnetism in manganites, uniform, ultra-thin films of La_{0.67}Sr_{0.33}MnO_3 were grown epitaxially on single crystal (001) LaAlO_3 and (110) NdGaO_3 substrates. The temperature and magnetic field dependent film resistance is used to probe the film's structural and magnetic properties. A surface and/or interface related dead-layer is inferred from the thickness… ▽ More To understand the near-interface magnetism in manganites, uniform, ultra-thin films of La_{0.67}Sr_{0.33}MnO_3 were grown epitaxially on single crystal (001) LaAlO_3 and (110) NdGaO_3 substrates. The temperature and magnetic field dependent film resistance is used to probe the film's structural and magnetic properties. A surface and/or interface related dead-layer is inferred from the thickness dependent resistance and magnetoresistance. The total thickness of the dead layer is estimated to be $\sim 30 Å$ for films on NdGaO_3 and $\sim 50 Å$ for films on LaAlO_3. △ Less

Submitted 30 September, 1998; originally announced September 1998.

Comments: 11 pages, 4 figures

Faceting Transition in an Exactly Solvable Terrace-Ledge-Kink model

Authors: D. B. Abraham, F. H. L. Essler, F. T. Latremoliere

Abstract: We solve exactly a Terrace-Ledge-Kink (TLK) model describing a crystal surface at a microscopic level. We show that there is a faceting transition driven either by temperature or by the chemical potential that controls the slope of the surface. In the rough phase we investigate thermal fluctuations of the surface using Conformal Field Theory. We solve exactly a Terrace-Ledge-Kink (TLK) model describing a crystal surface at a microscopic level. We show that there is a faceting transition driven either by temperature or by the chemical potential that controls the slope of the surface. In the rough phase we investigate thermal fluctuations of the surface using Conformal Field Theory. △ Less

Submitted 24 August, 1998; originally announced August 1998.

Comments: 27 pages, 18 EPS figures

Report number: OUTP-98-12S

Temperature- and Bias-dependence of magnetoresistance in doped manganite thin film trilayer junctions

Authors: J. Z. Sun, D. W. Abraham, K. Roche, S. S. P. Parkin

Abstract: Thin film trilayer junction of La$%_{0.67}$Sr$_{0.33}$MnO$_3$ - SrTiO$_3$ - La$_{0.67}$Sr$_{0.33}$MnO$_3$ shows a factor of 9.7 change in resistance, in a magnetic field around 100 Oe at 14K. The junction magnetoresistance is bias and temperature dependent. The energy scales associated with bias and temperature dependence are an order of magnitude apart. The same set of energies also determine t… ▽ More Thin film trilayer junction of La$%_{0.67}$Sr$_{0.33}$MnO$_3$ - SrTiO$_3$ - La$_{0.67}$Sr$_{0.33}$MnO$_3$ shows a factor of 9.7 change in resistance, in a magnetic field around 100 Oe at 14K. The junction magnetoresistance is bias and temperature dependent. The energy scales associated with bias and temperature dependence are an order of magnitude apart. The same set of energies also determine the bias and temperature dependence of the differential conductance of the junction. We discuss these results in terms of metallic cluster inclusions at the junction-barrier interface. △ Less

Submitted 6 July, 1998; originally announced July 1998.

Comments: 3 pages, 4 figures

Report number: cond.mat.jonsun.12563

Non-equilibrium Dynamics of Finite Interfaces

Authors: D. B. Abraham, T. J. Newman, G. M. Schütz

Abstract: We present an exact solution to an interface model representing the dynamics of a domain wall in a two-phase Ising system. The model is microscopically motivated, yet we find that in the scaling regime our results are consistent with those obtained previously from a phenomenological, coarse-grained Langevin approach. We present an exact solution to an interface model representing the dynamics of a domain wall in a two-phase Ising system. The model is microscopically motivated, yet we find that in the scaling regime our results are consistent with those obtained previously from a phenomenological, coarse-grained Langevin approach. △ Less

Submitted 20 April, 1994; originally announced April 1994.

Comments: 12 pages LATEX (figures available on request), Oxford preprint OUTP-94-07S